Engineering Commons^™

Effects Of Magnetite Particle Morphology On Adsorption Of Copper Ions From Aqueous Solutions, Alisa Hashley

Graduate Theses & Non-Theses

Adsorptive processes can be used for metal contaminant removal. This work addresses magnetite, a magnetic iron oxide, as the adsorbent for use in an adsorptive removal system, known as the continuous flow material recovery system (CFMR), developed by Leitzke et al. [1]. Though the system is effective in removing contaminants from aqueous solution, efforts to further improve efficiency are being made. One way to improve the efficiency of the CFMR is to analyze the magnetite particles being used and investigate how the particle properties effect adsorption. The author’s research is presented and discussed here to describe the effects magnetite particle …

Effect Of Chemical Identity And Morphology On Amphiphilic-Zwitterionic Block Copolymer Membranes, Ria Ghosh

Doctoral Dissertations

Amphiphilic block copolymers have gained a broad research interest attributed to their self-assembly properties over a range of pH, temperature, and ionic strength. Polyzwitterions have attracted special attention due to their hydrophilicity, charge sensitivity and coulombic attraction of the opposite charges over a range of environments making them a popular material of study in the field of stimuli responsive systems, for example in self-healing hydrogels, and water transport membranes. Combining the stimuli responsiveness and higher hydrophilicity of zwitterionic polymers with self-assembly behavior of amphiphilic block copolymers created an interest to study the effect of composition and identity of the zwitterionic …

Size Distribution, Elemental Composition And Morphology Of Nanoparticles Separated From Respirable Coal Mine Dust, Shoeleh Assemi, Lei Pan, Xuming Wang, Titilayo Akinseye, Jan D. Miller

Michigan Tech Publications

Nanoparticles, defined as particles with one dimension below 100 nm, contribute little to the total mass concentration in respirable coal mine dust (RCMD) toxicological studies, but they could have a considerable part in the adverse health effects by RCMD inhalation. It has been shown that inhaled nanoparticles can penetrate deep into the lung and could plausibly contribute to acute and chronic pulmonary diseases by triggering oxidative stress formation and inducing inflammation. RCMD nanoparticles from samples collected in an underground mine in the United States were analyzed by a particle separation technique, field-flow fractionation (FFF), for size, morphology, and elemental composition. …

A Study On Effect Of Manufacturing Parameters On Morphology Of A356 Aluminum Foam, Nikhil Nanabhau Mahajan

All Theses

Metal foams have shown an excellent promise for usage as multifunctional material concerning research & development in the last 20 years. They provide remarkable mechanical as well as physical properties being lightweight. Open-cell metal foams have already been used in sound and noise absorption. Open-cell metal foams are outstanding for use in heat exchangers, filters, and many more applications, while closed-cell foams show excellent characteristics in impact energy absorptions. Closed-cell metal foams have higher energy absorption than their solid parent metal as they convert most of the impact energy into deformation energy. Metal foams have been used as prominent safeguard …

Influence Of Electrolytic-Plasma Surface Quenching On The Structure And Strength Properties Of Ferritic-Pearlite Class Wheel Steel, B. K. Rakhadilov, Y. Y. Tabiyeva, G. K. Uazyrkhanova, L. G. Zhurerova, D. Baizhan

Eurasian Journal of Physics and Functional Materials

This paper examines the influence of electrolyte-plasma surface hardening on the structure and micro hardness of wheel steel mark 2. In the work electrolyte-plasma surface quenching was carried out in an electrolyte made from an aqueous solution of 10% carbamide (NH 2 ) 2 CO+20% sodium carbon ate Na 2 CO 3 . The work investigated the strength limit, fluidity and wear intensity of the wheeled steel after electrolyte-plasma surface quenching. After electrolytic-plasma surface quenching, a batch, high-temperature plate and low-temperature plate martensit is formed on the surface of the sample. Investigations have been carried out on microhardness determination on …

Investigation On The Morphology Of Charge-Transfer Complexes In Low Density Polyethylene, Wade Korf

Master's Theses

Fillers are used ubiquitously throughout the fields of polymer and material science to overcome many inherent limitations to polymeric materials (i.e. poor stiffness or strength) and to expand their potential applications. There is a need to develop controllable particle architectures to better understand fundamental structure-property relationships in particle reinforced polymer composites. Charge-transfer complexes (CTCs) can assemble in situ into various needle and dendritic shapes via simple fabrication processes and at low loading levels. In this study, the effect of tetrathiafulvalene (TTF) and 7,7,8,8-tetracyanoquinodimethane (TCNQ) CTC crystallites of various shapes and sizes on composite mechanical properties was investigated in an LDPE …

Atomic Force Microscopic Characterization Of Solid Electrolyte Interphase In Lithium Ion Batteries, Qing-Yu Dong, Yan-Li Chu, Yan-Bin Shen, Li-Wei Chen

Journal of Electrochemistry

In recent years, the rapid growing in the electric vehicle market has raised higher requirement on the lithium-ion batteries (LIBs) performance towards energy density and safety. However, considering the successful development of LIBs techniques in the past 30 years, there is little room left for improving the LIBs performance on the aspects related to the electrode materials, battery structure design and production processes. It is important to pursue more comprehensive fundamental understanding in the entire system and working principle of LIBs. Solid electrolyte interphase (SEI), existing between the electrode material and the electrolyte, has been proved to be an important …

Influences Of Morphology And Nitrogen Doping On The Electrocatalytic Characteristics For Oxygen Reduction Reaction Of Nio/Rgo, Dong Liang, Heng-Yi Fang, Shuo Yao, Jie-Mei Yu, Zhao-Liang Zhang, Zhan-Kun Jiang, Xue-Ping Gao, Tai-Zhong Huang

Journal of Electrochemistry

In this research, the reduced graphene oxide (rGO) supported sheet-like NiO (NiO/rGO) and spherical-like NiO (NiO/N-rGO) catalysts for oxygen reduction reaction (ORR) were prepared. The structures, morphologies and chemical states of the two catalysts were characterized by X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The electrochemical catalytic performance of the two catalysts for ORR were investigated by cyclic voltammetry (CV), Tafel, linear sweeping voltammetry (LSV), rotating disc electrode (RDE) and rotating ring disc electrode (RRDE) tests. Electrochemical results showed that the current density and onset potential (about 0.89 V) …

Polyurea Aerogels: From Nanoscopic To Macroscopic Properties, Tahereh Taghvaee

Doctoral Dissertations

"The morphology of a material is intrinsically a qualitative property and in order to relate nanomorphology to synthetic conditions, it is necessary to express nano/micro-structure quantitatively. In this context, polyurea aerogels were chosen as a model system with demonstrated potential for rich nanomorphology and being guided by a statistical Design-of-Experiments model, a large array of materials (208) with identical chemical composition, but quite different nanostructures were prepared. By reflecting upon the SEM images, it was realized that our first pre-verbal impression about a nanostructure is related to its openness and texture; the former is quantified by porosity (Π), and the …

Impacts Of Moisture On Asphalt Properties, Zahid Hossain

Publications

Stripping related moisture damage has been recognized as one of the major pavement distresses since the early 1990s. The main objective of this study is to establish an effective test protocol to quantify moisture susceptibility of asphalt pavements. To this end, selective test methods (Texas Boiling test, Tensile Strength Ratio, Retained Stability, and Hamburg Wheel Test), and procedures based on surface chemistries and molecular-level mechanistic properties have been investigated in this study. Firstly, a comprehensive list of literature related to moisture damage in asphalts was reviewed. Based on the literature review, a detailed project plan and test matrix were developed. …

Morphological And Energy Transport Optimization Of Spectrally-Selective Solar Absorber Coatings At Mesoscale, Dale Karas

UNLV Theses, Dissertations, Professional Papers, and Capstones

A special class of cuprous-based inorganic oxide materials, synthesized as nanoparticles via hydrothermal and co-precipitation methods, are portable to spectrally-selective absorber coatings with high solar-thermal energy conversion efficiency. Operating reliably at elevated temperatures when used in tandem with solar concentrators, these materials enable cost-competitive solar energy conversion technology that can be incorporated with thermal energy storage systems, supporting the viability of novel renewable power generation; notably, optimizing absorptive performance while mitigating thermal losses through re-radiated waste heat motivates sustainable energy production particular to desert climates, where water conservation and ecological sensitivity needs are paramount.

This work targets the chemical synthesis …

Comparing Laser Diffraction And Optical Microscopy For Characterizing Superabsorbent Polymer Particle Morphology, Size, And Swelling Capacity, Cole R. Davis, Stacey L. Kelly, Kendra Erk

School of Materials Engineering Faculty Publications

In this study, we determined the accuracy and practicality of using optical microscopy (OM) and laser diffraction (LD) to characterize hydrogel particle morphology, size, and swelling capacity (Q). Inverse-suspension-polymerized polyacrylamide particles were used as a model system. OM and LD showed that the average particle diameter varied with the mixing speed during synthesis for the dry (10–120 lm) and hydrated (34–240 lm) particles. The LD volume and number mean diameters showed that a few large particles were responsible for the majority of the water absorption. Excess water present in the gravimetric swelling measurements led to larger Qs (8.2 6 0.37 …

Synthesis, Characterization And Application Of Block Copolymer And Nanoparticle Composites, Yue Gai

Doctoral Dissertations

The “bottom-up” fabrication of functional hybrid material can be achieved by using directed self-assembly of functional nanoparticles (NP) and block copolymers (BCP) as templates. The versatile nanostructures of BCP provide possibilities to precisely control NPs spatial distribution and the resulting hybrid materials exhibit enhanced electrical, mechanical and optical functionalities. Three main topics related to BCP/NP composites are discussed in this dissertation: I) the spatial distribution of large NP in linear BCP; II) the morphology control of BCP templates with new architectures; and III) the magneto-optical properties of hybrid material using magnetic NPs. For well-ordered BCP/NP composite, the ratio of NP …

Synthesis Of Libob Fine Powder To Increase Solubility, Etty Marti Wigayati, Titik Lestariningsih, Christin Rina Ratri, Ibrahim Purawiardi, Bambang Prihandoko

Makara Journal of Technology

Lithium bis (oxalate) borate or LiBOB compound has captured interest of researchers, because it is potentially viable to be used as electrolyte salt in lithium-ion battery system. This compound is easy to synthesize and considered to be more environmentally friendly compared to conventional electrolyte salt because LiBOB does not contain halogen element. This research focused on the synthesis of LiBOB fine powder, which main purpose is improving LiBOB salt solubility in liquid electrolyte solution. This will aid the ion transfer between electrodes which in turn will increase the electrolyte performance. Solid state reaction was employed in this experiment. Synthesis of …

Polymer And Small Molecule Designs For Anion Conducting Membranes: Connected Ion-Channel Morphologies And Highly Alkaline Stable Ammonium Cations, Sedef P. Ertem

Doctoral Dissertations

Fuel cells are one of the oldest sustainable energy generation devices, converting chemical energy into electrical energy via reverse-electrolysis reactions. With the rapid development of polymer science, solid polymer electrolyte (SPE) membranes replaced the conventional liquid ion transport media, rendering low-temperature fuel cells more accessible for applications in portable electronics and transportation. However, SPE fuel cells are still far from commercialization due to high operation cost, and insufficient lifetime and performance limitations. Anion exchange membrane fuel cells (AEMFCs) are inexpensive alternatives to current proton exchange membrane fuel cell (PEMFC) technology, which relies on utilizing expensive noble-metal catalysts and perfluorinated SPE …

Morphology Evolution Mechanisms Of Low Band Gap Polymer-Based Photovoltaics, Sunzida Ferdous

Doctoral Dissertations

An optimal nanoscale phase separation between the donor (generally, a conjugated polymer) and the acceptor (generally, a fullerene derivative) materials is one of the major requirements for obtaining high efficiency organic photovoltaic (OPV) device. Recent methods of controlling such nanostructure morphology in a bulkheterojunction (BHJ) OPV device involve addition of a small amount of solvent additive to the donor and acceptor solutions. The idea is to retain the acceptor materials into the solution for a longer period of time during the film solidification process, thus allowing the donor material to crystallize earlier. The ultimate morphology resulting from the solvent casting …

Morphology-Property Relationship For Binary Organic Thin Films, Alyssa Lynn Griffin

Master's Theses

Organic thin films can be readily mass-produced through solution-based fabrication methods including ink-printing and solution-casting because their light weight, flexibility, and inexpensive sources. Their applications range from organic field-effect transistors (OFET), organic solar cells (OSC), to organic light emitting diodes (OLEDs). Compared with pure component films, binary organic thin films (BOTF) allows for novel characteristics and specialized features to handle more demanding tasks. Due to the complex intermolecular interactions in BOTF, various microscopic phases with different morphological and electronic properties may be formed and this information is difficult to extract through conventional bulk measurements.

Organic thin films can be readily …

Cure Kinetics, Morphologies, And Mechanical Properties Of Thermoplastic/Mwcnt Modified Multifunctional Glassy Epoxies Prepared Via Continuous Reaction Methods, Xiaole Cheng

Dissertations

The primary goal of this dissertation is to develop a novel continuous reactor method to prepare partially cured epoxy prepolymers for aerospace prepreg applications with the aim of replacing traditional batch reactors. Compared to batch reactors, the continuous reactor is capable of solubilizing and dispersing a broad range of additives including thermoplastic tougheners, stabilizers, nanoparticles and curatives and advancing epoxy molecular weights and viscosities while reducing energy consumption.

In order to prove this concept, polyethersulfone (PES) modified 4, 4’-diaminodiphenylsulfone (44DDS)/tetraglycidyl-4, 4’-diaminodiphenylmethane (TGDDM) epoxy prepolymers were firstly prepared using both continuous reactor and batch reactor methods. Kinetic studies confirmed the chain …

Characterization Of Dimethyl Sulfoxide-Treated Wool And Enhancement Of Reactive Wool Dyeing In Non-Aqueous Medium, Luyi Chen, Bijia Wang, Jiangang Chen, Xinhui Ruan, Yiqi Yang

Department of Textiles, Merchandising, and Fashion Design: Faculty Publications

Wool pretreated with dimethyl sulfoxide (DMSO) was characterized and its dyeing behavior in non-aqueous green solvents was investigated. Reactive dyeing of wool in deep shades is challenging because the mandatory alkaline aftertreatment to match the fastness of mordant dyes inevitably causes damage to wool keratin. The current study showed that the colorfastness-integrity dilemma could be solved by replacing water with organic solvents as the dyeing medium. Covalent fixation is predominantly favored in solvent dyeing so that excellent colorfastness is achievable at any given shade without alkali aftertreatment. Compared with aqueous dyeing, solvent dyeing was found to give 30% higher covalent …

Functional Nanocomposites From Self-Assembly Of Block Copolymers With Nanoparticles, Xinyu Wang

Doctoral Dissertations

This dissertation studied the proper distribution and location control of nanoparticles (NPs) within block copolymer (BCP) templates. A facile ligand exchange reaction was introduced for the hydrophilic magnetic NPs (MNPs) that are readily dispersed in polar solvents with outstanding stability. Small molecule ligands were selected to associate strongly with particle surfaces, provide hydrophilic termini for polarity matching with polar solvents, and offer the potential for hydrogen-bonding interactions to facilitate NP incorporation into polymers. Areal ligand densities of NPs indicated a significant increase in the ligand coverage after the exchange reaction. Hydrophilic MNPs were shown to drive the self-assembly of BCPs …

Creasing Instability Of Hydrogels And Elastomers, Dayong Chen

Doctoral Dissertations

CREASING INSTABILITY OF HYDROGELS AND ELASTOMERS MAY 2014 DAYONG CHEN, B.S., TIANJIN UNIVERISTY M.S., TIANJIN UNIVERSITY M.S., UNIVERSITY OF MASSACHUSETTS AMHERST Ph.D., UNIVERSITY OF MASSACHUSETTS AMHERST Directed by: Professor Ryan C. Hayward Soft polymers placed under compressive stress can undergo an elastic creasing instability in which sharp folds spontaneously form on the free surfaces. This process may play an important role in contexts as diverse as brain morphogenesis, failure of tires, and electrical breakdown of soft polymer actuators. While the creasing instability has been used for collotype printing since as early as the 1850s, the scientific appreciation of this instability …

Surface Modification Of Aluminum Alloys By Plasma Electrolytic Oxidation, Vahid Dehnavi

Electronic Thesis and Dissertation Repository

Plasma Electrolytic Oxidation (PEO) is a surface treatment for the production of ceramic oxide coatings with great properties, such as high wear and corrosion resistance, on metal substrates, particularly aluminum and magnesium alloys. Formation of PEO coatings involves complex processes and mechanisms that are difficult to study. Currently, the PEO process is in a transition phase from research to commercial application, with a primary focus on the corrosion and wear protection of light alloys, and has recently generated interest as a promising surface treatment for biomedical applications.

To justify the industrial application of PEO, a more systematic and in-depth study …

Structure And Morphology Of Sulfonated Polysulfone And Perfluorosulfonic Acid Ionomers, Chen Wang

Doctoral Dissertations

The limitations of conventional perfluorosulfonic acid (PFSA) based membrane materials have provoked the search for alternative materials which can function as the electrolyte in PEM fuel cells operated at higher temperatures (> 100 °C) and without humidification. A novel class of sulfonated poly(phenylene) sulfone (sPSO2) ionomers have shown much higher proton conductivity than typical PFSA membranes at elevated temperatures. In this dissertation, both computational and experimental methods were used to investigate proton transfer, morphological and structural properties of sPSO2 and PFSA ionomers. We have undertaken ab initio electronic structure calculations to understand the primary hydration and the transfer of protons …

The Effect Of Processing Parameters On Barrier Properties Of Polymers, Russell Louis Hallman Jr.

Doctoral Dissertations

The intent of this work was to learn if polyethylene could be made with predictable water transfer rates by control of the microstructure. A series of films were formed from three different polyethylenes with a range crystallinities using melt pressing, a controlled cooling rate, and subsequent heat treatments. The samples were tested on a novel device called the polymer characterization device that measures the water transfer flux as a function of temperature. The samples’ morphology was examined using differential gradient column, differential scanning calorimetry, Fourier transform infrared microscopy, wide-angle X-ray diffractions, small-angle X-ray scattering, and small angle light scattering, and …

Advanced Imaging As A Novel Approach To The Characterization Of Membranes For Microfiltration Applications, Milagro Marroquin

All Dissertations

This dissertation focuses on the design, development and implementation of novel, advanced imaging protocols for the characterization of membranes in microfiltration applications. Oftentimes, membrane characterization studies are done with high resolution microscopy techniques like scanning electron microscopy or transmission electron microscopy. The results obtained by these popular imaging techniques are subject to error and their reliability might be, in some instances, compromised because they require drying and metallization of the sample; working under high vacuum and electron beam intensity; and extensive sectioning to retrieve internal information. These factors may disrupt the membrane structure or modify its features. As an alternative …

Controlling Morphology In Swelling-Induced Wrinkled Surfaces, Derek Breid

Open Access Dissertations

Wrinkles represent a pathway towards the spontaneous generation of ordered surface microstructure for applications in numerous fields. Examples of highly complex ordered wrinkle structures abound in Nature, but the ability to harness this potential for advanced material applications remains limited. This work focuses on understanding the relationship between the patterns on a wrinkled surface and the experimental conditions under which they form. Because wrinkles form in response to applied stresses, particular attention is given to the nature of the stresses in a wrinkling surface. The fundamental insight gained was then utilized to account for observed wrinkle formation phenomena within more …

Morphology Changes In Pcpdtbt:Pcbm And P3ht:Pcpdtbt:Pcbm And Its Effect On Polymer Solar Cell Performance, Galen David Cauble

Physics

Polymer solar cell morphology is sensitive to both heat and time. By thermally annealing polymer solar cells the morphology of the devices can be altered causing immediate changes in device performance. Blending PCPDTBT:PCBM with P3HT:PCPDTBT combines the absorption characteristics of each to create a more even absorption spectrum. Subjecting PCPDTBT:PCBM, and P3HT:PCPDTBT:PCBM polymer solar cells to thermal annealing as well as recording device performance through time has shown that P3HT:PCPDTBT:PCBM devices react positively to thermal annealing (increasing from 0.8% to 1.4%) while PCPDTBT:PCBM devices have varied reactions. Furthermore, the P3HT:PCPDTBT:PCBM devices have achieved efficiencies of 1.6% in AM 1.5 compared …

Investigation Of The Processing, Structure And Properties Of Poly(Phenylene Sulfide) (Pps) Melt Spun Fibers, Prabhakar Gulgunje

Doctoral Dissertations

Numerous publications are available on the structure and properties correlation of fibers spun from polymers with flexible chains such as polyethylene terephthalate (PET), nylon, polypropylene. Also considerable amount of work is reported in fibers spun from rigid rod polymers like poly(p-phenylene terephthalamide) due to their value in high performance fibers category. However, very limited literature is available on the structure-properties relationship in fibers manufactured from poly(phenylene sulfide) (PPS), a high performance polymer which possesses chain flexibility between above two classes of polymers. A few researchers have studied crystallization kinetics and the fibers by extruding the polymer using capillary rheometers. However, …

Probing And Tuning The Size, Morphology, Chemistry And Structure Of Nanoscale Cerium Oxide, Satyanarayana Kuchibhatla

Electronic Theses and Dissertations

Cerium oxide (ceria)-based materials in the nanoscale regime are of significant fundamental and technological interest. Nanoceria in pure and doped forms has current and potential use in solid oxide fuel cells, catalysis, UV- screening, chemical mechanical planarization, oxygen sensors, and bio-medical applications. The characteristic feature of Ce to switch between the +3 and + 4 oxidation states renders oxygen buffering capability to ceria. The ease of this transformation was expected to be enhanced in the nanoceria. In most the practical scenarios, it is necessary to have a stable suspension of ceria nanoparticles (CNPs) over longer periods of time. However, the …

High Performance Zno Varistors Prepared From Nanocrystalline Precursors For Miniaturised Electronic Devices, Suresh Pillai, Declan Mccormack, John Kelly, Raghavendra Ramesh

Articles

An industrially viable solution-based processing route using minimal amounts of solvent has been used to prepare bulk quantity nanopowders (average particle size 15.3 nm) for the fabrication of ZnO varistors. The xerogels, calcined powders and sintered materials were fully characterised. The preparation of varistors from nanopowders has been optimised by studying the effect of temperature on grain growth, densification and breakdown voltage. The varistors are prepared by sintering at 1050 C for 2 hours, a temperature that is significantly lower than that used in the current industrial process. Highly dense varistor discs prepared from the sintered material produce devices, with …