Open Access. Powered by Scholars. Published by Universities.®
- Institution
- Publication
- Publication Type
Articles 1 - 6 of 6
Full-Text Articles in Engineering
Study On Electro-Sorption Of Heavy Metals And Sulfamethoxazole On Activated Carbon Fibers, Wen-Jun Zhao, Bing-Xin Jia, Ya-Nan Zhang, Jiu-Nian Guan, Jiao Qu, Ying Lu
Study On Electro-Sorption Of Heavy Metals And Sulfamethoxazole On Activated Carbon Fibers, Wen-Jun Zhao, Bing-Xin Jia, Ya-Nan Zhang, Jiu-Nian Guan, Jiao Qu, Ying Lu
Journal of Electrochemistry
To study the optimal removal condition, adsorption mechanism and comparative analysis of the three typical cationic pollutants, i.e., Zn(II), anionic pollutant Cr(VI) and molecular pollutant sulfamethoxazole (SMX), using self-made upflowed electro-sorption device for adsorptions of above three pollutants by modified activated carbon fiber were researched. The activated carbon fiber (ACF) was modified by hydrochloric acid. The ACF morphology and structure before and after modification were characterized by SEM, BET and FTIR. The characterization results show that the modified ACF had fewer surface impurities than the modified surface and the gully is more obvious, the specific surface area was increased by …
Open Source Waste Plastic Granulator, Arvind Ravindran, Sean Scsavnicki, Walker Nelson, Peter Gorecki, Jacob Franz, Shane Oberloier, Theresa K. Meyer, Andrew Barnard, Joshua M. Pearce
Open Source Waste Plastic Granulator, Arvind Ravindran, Sean Scsavnicki, Walker Nelson, Peter Gorecki, Jacob Franz, Shane Oberloier, Theresa K. Meyer, Andrew Barnard, Joshua M. Pearce
Michigan Tech Publications
In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built, and tested for its ability to convert post-consumer waste, 3D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404 W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than $2000 USD in materials. The experimentally measured power use …
Investigation Of Surface Treatment And Density Separation For Selective Recycling Of Plastics, Adilbek Baigabelov
Investigation Of Surface Treatment And Density Separation For Selective Recycling Of Plastics, Adilbek Baigabelov
Graduate Theses & Non-Theses
Froth flotation has been a useful method for flotation separation of plastics. Teeter bed concentration may also be potentially employed to accomplish gravity-based separation of plastics from a mixture. This work investigates selective separation of six different types of plastics using a novel method by combining advanced gravity concentration and froth flotation techniques. Surface active reagents were used during flotation studies for modification of surface properties of certain plastics in order to enhance selectivity. Elutriation technology in a teeter bed separator was successfully employed to achieve gravity-based concentration of certain plastics. The novel flowsheet was shown to recover plastics of …
Mechanical Properties And Applications Of Recycled Polycarbonate Particle Material Extrusion-Based Additive Manufacturing, Matthew J. Reich, Aubrey Woern, Nagendra Gautam Tanikella, Joshua M. Pearce
Mechanical Properties And Applications Of Recycled Polycarbonate Particle Material Extrusion-Based Additive Manufacturing, Matthew J. Reich, Aubrey Woern, Nagendra Gautam Tanikella, Joshua M. Pearce
Michigan Tech Publications
Past work has shown that particle material extrusion (fused particle fabrication (FPF)/fused granular fabrication (FGF)) has the potential for increasing the use of recycled polymers in 3D printing. This study extends this potential to high-performance (high-mechanical-strength and heat-resistant) polymers using polycarbonate (PC). Recycled PC regrind of approximately 25 mm2 was 3D printed with an open-source Gigabot X and analyzed. A temperature and nozzle velocity matrix was used to find useful printing parameters, and a print test was used to maximize the output for a two-temperature stage extruder for PC. ASTM type 4 tensile test geometries as well as ASTM-approved …
Reprapable Recyclebot: Open Source 3-D Printable Extruder For Converting Plastic To 3-D Printing Filament, Aubrey Woern, Joseph Mccaslin, Adam Pringle, Joshua M. Pearce
Reprapable Recyclebot: Open Source 3-D Printable Extruder For Converting Plastic To 3-D Printing Filament, Aubrey Woern, Joseph Mccaslin, Adam Pringle, Joshua M. Pearce
Joshua M. Pearce
In order to assist researchers explore the full potential of distributed recycling of post-consumer polymer waste, this article describes a recyclebot, which is a waste plastic extruder capable of making commercial quality 3-D printing filament. The device design takes advantage of both the open source hardware methodology and the paradigm developed by the open source self-replicating rapid prototyper (RepRap) 3-D printer community. Specifically, this paper describes the design, fabrication and operation of a RepRapable Recyclebot, which refers to the Recyclebot’s ability to provide the filament needed to largely replicate the parts for the Recyclebot on any type of RepRap 3-D …
Development And Characterization Of Polyethylene Terephthalate (Pet)-Cotton Natural Fiber-Reinforced Composites From Waste Materials, Israel Alejandro Carrete
Development And Characterization Of Polyethylene Terephthalate (Pet)-Cotton Natural Fiber-Reinforced Composites From Waste Materials, Israel Alejandro Carrete
Open Access Theses & Dissertations
Unprecedented levels of production and consumption have caused a rapid exhaustion of the Earth's virgin resources, which is coupled with a fast accumulation of contaminants in the form of solid waste, especially in landfills. Two significant landfill constituents come from textile waste and discarded plastic bottles. Since there is a finite amount of space that can be feasibly used for landfills, solutions that make use of these post-consumer products are imperative. This study presents one possible solution by using surface modifications of cotton fibers to produce a natural fiber-reinforced polymer composite (NFRPC) from post-consumer textile waste and polyethylene terephthalate (PET) …