Engineering Commons^™

Exploring A Platinum Nanocatalytic Microcombustion-Thermoelectric Coupled Device, Dylan Moore Mcnally

Theses and Dissertations

This work aimed to create a first-generation power device for eventual application to portable electronics. A platinum nanoparticle catalytic substrate was employed in a microcombustion-thermoelectric coupled (MTC) device for the purpose of chemical-to-electrical energy conversion. Multiple microcombustion reactors were designed, fabricated, and investigated. Most importantly, the reactor configuration was designed to accommodate thermoelectric generators (TEGs) for power production. Temperature studies with catalytic combustion of methanol-air fuel mixtures were used to evaluate the thermal power generation performance of each reactor. The final reactor design enabled ignition at room temperature with the ability to achieve repeat catalytic cycles upon subsequent exposure to …

A Study On Latent Thermal Energy Storage (Ltes) Using Phase Change Materials (Pcms) 2020, Ritvij Dixit

Masters Theses

The significant increase in energy requirements across the world, provides several opportunities for innovative methods to be developed to facilitate the storage and utilization of energy. The major energy demand is in the form of electrical energy for domestic as well as industrial sectors, a large part of which are the heating and cooling requirements. Appropriate utilization of thermal energy storage can effectively aid in reducing the electrical demand by storage and release of this thermal energy during peak hours.

Thermal Energy Storage using Phase Change Materials (PCMs) is an attractive method of energy storage, with a wide variety of …

Thermo-Fluid Characterizations Of The Powder-Bed Fusion Additive Manufacturing Processes Using Laser And Electron Beam, M Shafiqur Rahman

University of New Orleans Theses and Dissertations

The powder-bed fusion (PBF) process is a subdivision of Additive Manufacturing (AM) technology where a heat source at a controlled speed selectively fuses regions of a powder-bed material to form three-dimensional (3-D) parts. Two of the most effective PBF processes are selective laser melting (SLM) and electron beam additive manufacturing (EBAM), which can fabricate full-density metallic parts in a layer-by-layer fashion. In this study, thermal behavior and melt-pool dynamics in the PBF process are investigated by developing 3-D multiphysics-based thermo-fluid models for both SLM and EBAM, containing Ti-6Al-4V alloy as a powder-bed material. The laser and electron beams are modeled …

Performance Improvements For Next Generation Falling Particle Receiver Systems, Nathan R. Schroeder

Mechanical Engineering ETDs

Falling particle receiver (FPR) systems are a rapidly developing technology for concentrating solar power applications. Solid particles are used as both the heat transfer fluid and thermal energy storage media. Through the direct solar irradiation of the solid particles, flux and temperature limitations of tube-bundle receives can be overcome leading to higher operating temperatures and energy conversion efficiencies. Particle residence time, curtain opacity, and curtain stability affect the performance of FPR designs. As the particles fall through the receiver the curtain accelerates, increasing its transmissivity thus decreasing the amount of energy absorbed. Multistage release trough structures catch and release the …

Development Of A Tiny House Design Tool To Increase Safety, Efficiency, And Cost-Effectiveness, Michael Joseph Stratton Ii

Masters Theses

A growing number of people are choosing to live more sustainably, and this is commonly done through living in an extremely small house, also called a “tiny house”. There is no set definition for a tiny house, but it typically refers to a structure less than 500 ft2, sometimes built by the homeowner, and frequently built on a travel trailer.

The popularity of tiny houses has increased over the years due to different television shows, internet videos, and photo sharing websites, but the technical details are rarely covered, which is why this study examines the structural, stability, weight, and thermal …

A Method For Developing And Testing Nuclear Reactor Systems With Space Applications And Improving Performance Of Heat Pipe Reactor Systems, David Duff Dixon

Doctoral Dissertations

The concept of using nuclear reactor technology in propulsion systems is nearly as old as nuclear reactors themselves. Numerous publications, many at very primitive conceptual levels, suggested nuclear propulsion in the 1940s. Since then, numerous attempts have been made to build and fly a nuclear rocket, yet there have been no such systems advanced to the point of a system test in more than half a century.

This dissertation presents an approach to reactor system development, a testing approach developed by the author that resulted in the operation of the world’s first heat pipe reactor system, and the world’s first …

Molecular Mechanisms And Design Of Hydrogen-Bonded Materials For Thermal Applications, Jinlong He

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Heat transfer at the nanoscale plays an important role in determining the reliability and performance of many innovative advanced materials technologies such as nanoelectronics, semiconductor, biomedical devices, polymers, and composites. Extensive efforts have been made to design materials with extraordinary thermal properties. However, fundamental understanding of heat transfer in many of these materials is still not lacking, because the thermal transport processes are governed by several factors including molecular morphology and chemical bonding. Among these factors, the atomic bonding between two dissimilar materials or within single materials is of particular interest due to its ubiquity and importance in physical processes. …

Heat Transfer Modeling And Optimization Of A Carbonized Microvascular Solar Receiver, Taylor Brown

Boise State University Theses and Dissertations

Concentrating solar power is an emerging renewable energy source. The technology can collect and store thermal energy from the sun over long durations, generating electricity as needed at a later time. Current CSP systems are limited to a maximum operational temperature due to constraints of the working fluid, which limits the maximum possible efficiency of the system. One proposed pathway forward is to utilize a gas phase for the working fluid in the system such as supercritical carbon dioxide.

A composite gas phase modular receiver is being developed by researchers at Boise State University and the University of Tulsa. The …

Effect Of Adding Palm Fiber To Thermal Conductivity Of Quick Set Concrete, Monica Garcia

Theses and Dissertations

As climate change becomes a more dire issue and more readily accepted by those in power, the demand for local and systemic solutions grows louder. In urban environments, one issue of concern is the contribution of anthropogenic heat from buildings which contributes to localized warming of the environment. A method that can reduce anthropogenic heat is decreasing the thermal conductivity of building materials. The objective of this study is to examine the possibility of using palm fibers to reduce the thermal conductivity of quick-set concrete samples. The data gathered in this study are used to determine the thermal conductivity value …

Numerical Modeling And Conjugate Heat Transfer Analysis Of Single U-Tube Vertical Borehole Heat Exchangers, Talha Khan

FIU Electronic Theses and Dissertations

The primary purpose of this thesis was to develop a design for improving the efficiency of the vertical type single u-tube borehole heat exchanger. A thorough literature review of the various existing analytical and numerical models of the borehole heat exchanger (BHEs) was performed and numerical modeling of the BHE was conducted to solve the conjugate heat transfer problem in the BHE in 3D using ANSYS Fluent 2019 R1. A comparison between the results obtained using various mesh sizes, types, different turbulence models showed the independence of the parameters on the numerical simulation results.

From the numerical simulation, it was …

Characterization For Spray Droplet Behaviour In Afterburner-Like Flow Conditions, Matthew D. Mahaffy

Electronic Thesis and Dissertation Repository

Fuel injection processes can contribute to combustion instability in highly energetic combustion systems. In gas turbine engine afterburners, jet-in-crossflow (JIX) injection is used. Part one of the thesis study investigates the interaction between spray droplets and turbulent flow properties of a JIX. Jet-in-counterflow (JIC) configuration was also investigated. Part two of the investigation examined the behaviour of JIX droplets around a bluff body. Droplet size and flow turbulence was characterized simultaneously using particle image velocimetry and image processing techniques. Turbulence and droplet size were correlated, particularly at momentum flux ratios ≥ 60. High speed imaging was used to identify droplet …

Sustainable Smouldering For Waste-To-Energy: Scale, Heat Losses, And Energy Efficiency, Tarek L. Rashwan

Electronic Thesis and Dissertation Repository

Applied smouldering combustion is emerging as a highly energy efficient approach towards waste-to-energy. This thesis aims to better understand this potential by addressing a critical knowledge gap between laboratory scale smouldering research and large-scale applications. Altogether, new understanding in provided on the complex and dynamic interactions between the reaction zone (smouldering front) and the cooling zone (treated inert porous media) by integrating theory, experiments, analytical modelling, and global energy balance calculations. The experiments spanned a range of reactor sizes and smouldering conditions (from weak to robust) with dry (carbon) and wet (sludge) fuels mixed in sand. This work revealed that …

Modeling, Simulation, And Testing Of Sweeping Convection, Amir Kiaee

Mechanical Engineering Research Theses and Dissertations

In this study, the new convection heat transfer concept of sweeping convection, using large particles flowing with a fluid in a channel, is considered. This novel concept is inspired by the gas exchange process in alveolar capillaries, where red blood cells (RBCs) flow with blood plasma, yielding very high gas transfer efficiency. An important characteristic of alveolar capillary blood flow, believed to be related to the high efficiency of the lungs, is the snug fitting of the RBCs into the capillaries. This tight fitting sets the RBCs (particles) acting like pistons as they flow downstream with the plasma (fluid), facilitating …

Thermal Control Development Of A Proton Exchange Membrane Fuel Cell System, Ola Mohammed Taha Al-Shalash

Mechanical Engineering Theses

A fuel cell is an electrochemical energy conversion device that uses fuel to generate electricity. It basically converts the chemical energy of reactants directly into electricity without combustion. In a Proton Exchange Membrane Fuel Cell (PEMFC), the reactants, hydrogen and oxygen, are fed into the two electrodes, anode and cathode, respectively. A reaction takes place at each electrode and produces electricity, as well as water, and heat as the by-products. In order to maximize performance of a fuel cell, many factors can be considered for tuning and control. Temperature management is one of these factors.

A thermal-fluid model of a …

Potential Energy Generation From Agricultural Residue In Indonesia, Adrian Rizqi Irhamna

English Language Institute

Indonesia has great potential of biomass sources from their agricultural residue, which can potentially be used for alternative energy generation. This preliminary research explores the most suitable technology for energy generation from agricultural residue and its challenge for application in Indonesia. The study showed that biomass utilization via the direct combustion process is recommended for energy generation. It is also reported that the pretreatment process of drying and washing, are required to increase the fuel quality and plant efficiency.

Cooking Systems Using Aluminum Foam, Ryan Tetsuo Mizukami

Physics

In developing countries, the use of wood burning fires for cooking is cause for illness and death. With this in mind, research was conducted to develop a solar cooking device capable of cooking of soup within 15 mins in order to reduce the negative impacts of cooking with wood. Current methods of solar-based cooking, such as solar concentrators and solar tube ovens, are impractical. A small solar panel is a cost-effective way to produce energy but will not produce enough power to cook within a reasonable amount of time. Even if it is assumed that all of the energy produced …

Survivability Investigation Of Cylindrical Shaped Water Cooled Probe In High Heat Flux Conditions, Joshua Osborne

Masters Theses

Diagnostics and data collection downstream of turbine engine augmentors and scramjet combustors provide critical information for turbine engine and scramjet engine developers. One important diagnostic tool is the use of imaging measurement instruments, which are primarily used by the aeropropulsion ground testing community to assess flame holder stability and uniformity in turbine engines. The survivability limitations of these imaging probes are important to understand for use in applications behind ramjet or scramjet engines, where mass flows and exhaust temperatures exceed typical engine augmentor exhaust streams. At a minimum, imaging data acquired behind ramjet and scramjet engines would be used to …

What Difference Does A Catalyst Make?, Tammy Guthrie, Mike Jackson, Holly Haney

High School Lesson Plans

Students will use different catalysts for the decomposition of Hydrogen Peroxide, to determine if different catalysts affect the energy that is generated during the reaction.

Raysun's Infrared Raisin Dryer, Lucas Kensinger, Saraith Aispuro, Joe Vanacore

General Engineering

The RaySuns senior project team was tasked with lowering the drying costs of raisins for River Ranch Raisins. In doing so, we explored several options for cutting costs: utilizing automation and exploring new drying technologies were our primary focus. We eventually planned a modular infrared heating mechanism which would be easy to automate in future projects. After manufacturing and testing an infrared heating mechanism, it was found that infrared drying could significantly cut costs versus the previous natural gas fired dryer tunnels while leaving room for automation. The infrared dryer was also shown to have the potential to create high-quality …

Design For Additive Manufacturing, Michael Charonnat, Leonardo Franco-Muñoz, Sam Noble, J.P. Purdom

Mechanical Engineering

This document outlines the critical design details and timeline for the Design for Additive Manufacturing Senior Project sponsored by Solar Turbines, Inc. The scope of this project encompasses the redesign of two of Solar Turbine’s cast parts for metal additive manufacturing in order to minimize lead time, cost, and weight. With the overall objective of performing in-depth analysis exploring affordability & feasibility, this redesign process will aid Solar Turbines in expanding their knowledge of Design for Additive Manufacturing principles and enable them to further incorporate the use of additive manufacturing into their production processes. The first part that the team …

Analysis Of Burning Wood In The Transient State And The Application To Structural Design, Roberta Veliz, Kimberly Guzman

Architectural Engineering

Determining the extent of the contribution of exposed timber on compartment fire dynamics in open floor plans is a complex process. Designers traditionally used compartmentalization design methods which create spaces where flashover is likely, given the fuel load and ventilation conditions. However, due to the large geometric dimensions and spread of fuel, fires in open floor plans are more likely to remain as localized or traveling fires. As such, an understanding of not only ignition potential but also flame spread is critical to characterizing the contribution of exposed timber. An integral step in characterizing the potential contribution is through an …

Development Of Reduced Chemical Kinetic Models For The Numerical Simulation Of Combustion And Emissions Behavior Of Representative Conventional And Bio-Derived Fuels, Mazen A. Eldeeb

Mineta Transportation Institute

The study addresses two of the main challenges facing combustion modeling for transportation fuels: simultaneous simulation of non-related combustion problems and reducing the computational cost of the modeling process itself. To address the first challenge, researchers determine a characteristic flame time from thermal diffusivity and laminar burning velocity. Researchers examine parametric dependence of flame time and ignition delay time on pressure, temperature and equivalence ratio for methane, based on validated chemical kinetic mechanisms. The study reveals flame time and ignition delay time show similar temperature dependence, flame time has stronger dependence on equivalence ratio and weaker dependence on pressure than …

The Effect Of Orientation On The Ignition Of Solids, David Morrisset

Master's Theses

The ignition of a solid is an inherently complex phenomenon influenced by heat and mass transport mechanisms that are, even to this day, not understood in entirety. In order to use ignition data in meaningful engineering application, significant simplifications have been made to the theory of ignition. The most common way to classify ignition is the use of material specific parameters such as such as ignition temperature (T_ig) and the critical heat flux for ignition (CHF). These parameters are determined through standardized testing of solid materials – however, the results of these tests are generally used in applications …

Fly Ash Based Geopolymer For High Temperature And High Compressive Strength Applications In Aggressive Environment, Aaryan Manoj Nair, Akm S. Rahman

Publications and Research

Geopolymers are the results of geosynthetic reactions between aluminosilicates and strong bases. This results in chemical bonds between aluminum (Al), Silicon (Si)and oxygen (O) composing polymer rings in tetrahedral coordination. These bonds give them widespread useful applications such as high heat bearing ceramics, and base construction material whilst being far more environmentally conscious. The purpose of the experiment is to examine the effect of Silicon Carbide whisker and inorganic glass particles on thermal and mechanical properties of Geopolymers. This study will help understand the effect of various compositions and concentrations of SiO₂ in mechanical strength. In this experiment, the …

Development And Application Of Elliptic Blending Lag K-Omega Sst Standard And Wall-Distance-Free Turbulence Model, Wenjie Shang

McKelvey School of Engineering Theses & Dissertations

In recent decades, Computational Fluid Dynamics (CFD) has become the most widely used technology to understand the fundamental complex fluid dynamics of turbulent flows as well as for modeling of turbulent flows in industrial applications. In industrial applications, the widely used methodology is to solve Reynolds-Average Navier-Stokes Equations (RANS) equations in conjunction with a turbulence model since it strikes a balance between accuracy and computational cost compared to other high fidelity approaches namely the Large Eddy Simulation (LES) and Direct Numerical Simulation (DNS), There are a large number of turbulence models proposed in past five decades, majority of them are …

The Development Of All Solid-State Optical Cryo-Cooler, Junwei Meng

Optical Science and Engineering ETDs

This dissertation describes the development of an all solid-state optical cryo-cooler. Crystals of 10% wt. ytterbium-doped yttrium lithium fluoride (Yb³⁺:YLF) are used to cool an infrared HgCdTe sensor payload to an absolute temperature below 135 K, equivalent to delta T equal 138 K below ambient. This record level of cooling is accomplished with a single stage, in a completely vibration-free environment, with a corresponding cooling power of 190 mW. This milestone is made possible by the design and fabrication of an undoped YLF thermal link that efficiently shields the payload with a non-right angle kink from intense anti-Stokes …

A Study Of The Efficiency And Effectiveness Of The First Four Iterations Of Sierpinski Carpet Fractal-Like Fins At Increasing Angles In Natural Convection, Sophia N. Fleri

Honors College Theses

Fractal geometries have been found in several studies to increase a fin’s thermal performance. Both the reductions of volume and mass accompanied by an increase in performance are desirable to prevent malfunction of the device through passive heat dissipation. The Sierpinski carpet fractal pattern, beginning with a basic square geometry in which an increasing number of perforations are incorporated through each successive iteration, reduces the fin’s mass while increasing its surface area simultaneously; this increase in surface area increases the rate of heat transfer experienced across the fin. The first four iterations of the Sierpinski carpet pattern, each with identical …

Enhancement Of Phase Change Material Sorbitol By Nanoparticle Inclusion For Improving Thermal Energy Storage Capabilities, Joshua Kasitz

Mechanical Engineering Undergraduate Honors Theses

Thermal management of electronic devices has become an increasingly vital field of study with the rapid miniaturization of many key electrical components. With the significant improvement of semiconductor manufacturing and intensified focus on interconnects, electronic devices have decreased in size at an incredible rate. Decreasing spatial requirements is essential to improving device capabilities as the electronic system is able to incorporate more components. Currently, electronic systems are drastically limited by the capabilities of their cooling mechanisms. Smaller devices lead to large increases in the energy density of the system and require more powerful cooling systems to maintain proper component operating …

Computational Analysis Of A New Planar Mixing Layer Flame Configuration To Study Soot Inception, Carmen Ciardiello

Honors Scholar Theses

The production of soot is omnipresent in society today. Soot is the product of many of the combustion processes that provide the bulk of the usable energy throughout the world. Furthermore, soot particulate poses a great danger to both the environment and all forms of life on Earth. It has proven to pollute ecosystems, foster health problems for human beings, and degrade air quality [1].

These dangers make studying and understanding soot particulate paramount for improving the quality of life. Thus, this study introduces a new flame configuration for studying soot inception. Presently, various common flame configurations have been found …

Portable Calorimeter For Fire Experiments, Kayla Collins, Kara Hewson, Christopher Chen, Joel Keddie

Mechanical Engineering

Executive Summary

An oxygen consumption calorimeter works by measuring the heat release rate of a burning substance. This value is calculated by measuring the oxygen and byproducts in smoke from afire.In order to get these values two types of sensors were used. A non-dispersive infrared sensor (NDIR) that measured CO and CO2 and a zirconium O2 sensor were used to find their respective gas concentrations.The design to calculate the heat release rate is focused on maximizing sensor accuracy and portability while simplifying the manufacturing by using off-the-shelf components. The goal included making the system simple to recreate and package in …