Engineering Commons^™

Design And Comparison Of Asynchronous Fft Implementations, Julie Bigot

Graduate Theses and Dissertations

Fast Fourier Transform (FFT) is a widely used digital signal processing technology in a large variety of applications. For battery-powered embedded systems incorporating FFT, its physical implementation is constrained by strict power consumption, especially during idle periods. Compared to the prevailing clocked synchronous counterpart, quasi-delay insensitive asynchronous circuits offer a series of advantages including flexible timing requirement and lower leakage power, making them ideal choices for these systems. In this thesis work, various FFT configurations were implemented in the low-power Multi-Threshold NULL Convention Logic (MTNCL) paradigm. Analysis illustrates the area and power consumption trends along the changing of the number …

Electrical Modeling For Dynamic Performance Prediction And Optimization Of Mcpms Layout, Quang Minh Le

Graduate Theses and Dissertations

In recent years, the fast development of Multichip Power Modules (MCPM) packaging and Wide Bandgap (WBG) technology has enabled higher voltage and current ratings, better thermal performance, lower parasitic parameters, and higher mechanical reliability. However, the design of the MCPM layout is a multidisciplinary problem leading to many time-consuming analyses and tedious design processes. Because of these challenges, the design automation tool for MCPM layout has become an emerging research area and gained much attention from the power electronics community. The two critical objectives of a design automation tool for MCPM layout are fast and accurate models for design insights …

Framework Of Hardware Trojan Detection Leveraging Structural Checking Tool, Rafael Dacanay Del Carmen

Graduate Theses and Dissertations

Since there is a significant demand for obtaining third-party soft Intellectual Property (IP) by first-party integrated circuit (IC) vendors, it is becoming easier for adversaries to insert malicious logic known as hardware Trojans into designs. Due to this, vendors need to find ways to screen the third-party IPs for possible security threats and then mitigate them. The development of the Structural Checking (SC) tool provides a solution to this issue. This tool analyzes the structure of an unknown soft IP design and creates a network of all the signals within the design and how they are connected to each other. …

Computational Frameworks For Multi-Robot Cooperative 3d Printing And Planning, Laxmi Prasad Poudel

Graduate Theses and Dissertations

This dissertation proposes a novel cooperative 3D printing (C3DP) approach for multi-robot additive manufacturing (AM) and presents scheduling and planning strategies that enable multi-robot cooperation in the manufacturing environment. C3DP is the first step towards achieving the overarching goal of swarm manufacturing (SM). SM is a paradigm for distributed manufacturing that envisions networks of micro-factories, each of which employs thousands of mobile robots that can manufacture different products on demand. SM breaks down the complicated supply chain used to deliver a product from a large production facility from one part of the world to another. Instead, it establishes a network …

Achieving Differential Privacy And Fairness In Machine Learning, Depeng Xu

Graduate Theses and Dissertations

Machine learning algorithms are used to make decisions in various applications, such as recruiting, lending and policing. These algorithms rely on large amounts of sensitive individual information to work properly. Hence, there are sociological concerns about machine learning algorithms on matters like privacy and fairness. Currently, many studies only focus on protecting individual privacy or ensuring fairness of algorithms separately without taking consideration of their connection. However, there are new challenges arising in privacy preserving and fairness-aware machine learning. On one hand, there is fairness within the private model, i.e., how to meet both privacy and fairness requirements simultaneously in …

Analog Spiking Neural Network Implementing Spike Timing-Dependent Plasticity On 65 Nm Cmos, Luke Vincent

Graduate Theses and Dissertations

Machine learning is a rapidly accelerating tool and technology used for countless applications in the modern world. There are many digital algorithms to deploy a machine learning program, but the most advanced and well-known algorithm is the artificial neural network (ANN). While ANNs demonstrate impressive reinforcement learning behaviors, they require large power consumption to operate. Therefore, an analog spiking neural network (SNN) implementing spike timing-dependent plasticity is proposed, developed, and tested to demonstrate equivalent learning abilities with fractional power consumption compared to its digital adversary.

Stay-At-Home Motor Rehabilitation: Optimizing Spatiotemporal Learning On Low-Cost Capacitive Sensor Arrays, Reid Sutherland

Graduate Theses and Dissertations

Repeated, consistent, and precise gesture performance is a key part of recovery for stroke and other motor-impaired patients. Close professional supervision to these exercises is also essential to ensure proper neuromotor repair, which consumes a large amount of medical resources. Gesture recognition systems are emerging as stay-at-home solutions to this problem, but the best solutions are expensive, and the inexpensive solutions are not universal enough to tackle patient-to-patient variability. While many methods have been studied and implemented, the gesture recognition system designer does not have a strategy to effectively predict the right method to fit the needs of a patient. …

Automatic Methods To Enhance The Quality Of Colonoscopy Video, Nidhal Kareem Shukur Azawi

Graduate Theses and Dissertations

Colonoscopy is a form of endoscopy because it uses colonoscopy device to help the doctor to understand a colon patient. Enhancing the quality of Colonoscopy images is a challenge because of the wet and dynamic environment inside the colon causes many problems even the colonoscope devise has a good quality. Some of these problems are blurriness, specular highlights shiny areas.

In this work, different kinds of techniques have been investigated in order to improve the quality of colonoscopy images. Also, variety of preprocessing approaches (removing bad images, resizing images, median filtration with and without image resizing) have been conducted to …

Collaborative Robotic Path Planning For Industrial Spraying Operations On Complex Geometries, Steven Brown

Graduate Theses and Dissertations

Implementation of automated robotic solutions for complex tasks currently faces a few major hurdles. For instance, lack of effective sensing and task variability – especially in high-mix/low-volume processes – creates too much uncertainty to reliably hard-code a robotic work cell. Current collaborative frameworks generally focus on integrating the sensing required for a physically collaborative implementation. While this paradigm has proven effective for mitigating uncertainty by mixing human cognitive function and fine motor skills with robotic strength and repeatability, there are many instances where physical interaction is impractical but human reasoning and task knowledge is still needed. The proposed framework consists …

Automatic Performance Optimization On Heterogeneous Computer Systems Using Manycore Coprocessors, Chenggang Lai

Graduate Theses and Dissertations

Emerging computer architectures and advanced computing technologies, such as Intel’s Many Integrated Core (MIC) Architecture and graphics processing units (GPU), provide a promising solution to employ parallelism for achieving high performance, scalability and low power consumption. As a result, accelerators have become a crucial part in developing supercomputers. Accelerators usually equip with different types of cores and memory. It will compel application developers to reach challenging performance goals. The added complexity has led to the development of task-based runtime systems, which allow complex computations to be expressed as task graphs, and rely on scheduling algorithms to perform load balancing between …

The Effect Of Incorporating End-User Customization Into Additive Manufacturing Designs, Jonathan D. Ashley

Graduate Theses and Dissertations

In the realm of additive manufacturing there is an increasing trend among makers to create designs that allow for end-users to alter them prior to printing an artifact. Online design repositories have tools that facilitate the creation of such artifacts. There are currently no rules for how to create a good customizable design or a way to measure the degree of customization within a design. This work defines three types of customizations found in additive manufacturing and presents three metrics to measure the degree of customization within designs based on the three types of customization. The goal of this work …

A Proposed Approach To Hybrid Software-Hardware Application Design For Enhanced Application Performance, Alex Shipman

Graduate Theses and Dissertations

One important aspect of many commercial computer systems is their performance; therefore, system designers seek to improve the performance next-generation systems with respect to previous generations. This could mean improved computational performance, reduced power consumption leading to better battery life in mobile devices, smaller form factors, or improvements in many areas. In terms of increased system speed and computation performance, processor manufacturers have been able to increase the clock frequency of processors up to a point, but now it is more common to seek performance gains through increased parallelism (such as a processor having more processor cores on a single …

Automatic User Profile Construction For A Personalized News Recommender System Using Twitter, Shiva Theja Reddy Gopidi

Graduate Theses and Dissertations

Modern society has now grown accustomed to reading online or digital news. However, the huge corpus of information available online poses a challenge to users when trying to find relevant articles. A hybrid system “Personalized News Recommender Using Twitter’ has been developed to recommend articles to a user based on the popularity of the articles and also the profile of the user. The hybrid system is a fusion of a collaborative recommender system developed using tweets from the “Twitter” public timeline and a content recommender system based the user’s past interests summarized in their conceptual user profile. In previous work, …

Extending The Hybridthread Smp Model For Distributed Memory Systems, Eugene Anthony Cartwright Iii

Graduate Theses and Dissertations

Memory Hierarchy is of growing importance in system design today. As Moore's Law allows system designers to include more processors within their designs, data locality becomes a priority. Traditional multiprocessor systems on chip (MPSoC) experience difficulty scaling as the quantity of processors increases. This challenge is common behavior of memory accesses in a shared memory environment and causes a decrease in memory bandwidth as processor numbers increase. In order to provide the necessary levels of scalability, the computer architecture community has sought to decentralize memory accesses by distributing memory throughout the system. Distributed memory offers greater bandwidth due to decoupled …