Engineering Commons^™

Numerical And Semi-Analytical Estimation Of Convective Heat Transfer Coefficient For Buildings In An Urban-Like Setting, Anwar Demsis Awol

Electronic Thesis and Dissertation Repository

Urban building arrangements such as packing density, orientation and size are known to influence the microclimate surrounding each building. Studies on the impact of urban microclimatic changes on convective heat transfer coefficient (CHTC) from a stock of buildings, however, have been rare in surveyed literature. The present study focuses on numerical and analytical investigation of CHTC from building-like models with homogeneous set of equal and unequal planar and frontal densities. Consequently, the study discusses the CHTC response in relation to broader changes in the urban surface form. Part of the process involves the development of a simplified one-dimensional semi-analytical CHTC …

Development Of A Comsol Microdialysis Model, Towards Creation Of Microdialysis On A Chip With Improved Geometries And Recovery, Patrick Pysz

Graduate Theses and Dissertations

Microdialysis (µD) sampling is a diffusion-limited sampling method that has been widely used in different biomedical fields for greater than 35 years. Device calibration for in vivo studies is difficult for current non-steady state analytes of interest correlated with both inflammatory response and microbial signaling molecules (QS); which exist in low ng/mL to pg/mL with molecular weights over a wide range of 170 Da to 70 kDa. The primary performance metric, relative recovery (RR), relating the collected sample to the extracellular space concentration varies from 10% to 60% per analyte even under controlled bench-top conditions. Innovations in microdialysis device design …

Residual Stress Models For Large Eddy Simulation Of Stratified Turbulent Flows, Felipe Augusto Ventura De Bragança Alves

Doctoral Dissertations

The residual stresses and scalar fluxes are required to close the momentum and scalar transport equations in simulations of turbulence that are not fully resolved in space. In stratified turbulence, the stress and fluxes are statistically anisotropic unless the smallest resolved length scale is smaller than the Ozmidov scale and the buoyancy Reynolds number is sufficiently high for there to exist a range of scales that is statistically isotropic. In this work, a tensorial basis set is derived analytically that potentially contains sufficient information about the anisotropic interaction between resolved and residual scales. The residual stress tensor is evaluated by …

A Cfd Study Of Steady Fully Developed Laminar Flow Through A 90-Degree Bend Pipe With A Square Cross-Sectional Area, Subodh Sushant Toraskar

Mechanical & Aerospace Engineering Theses & Dissertations

Fluid flow through a closed curved conduit has always been a topic of extensive research, as it has many practical and industrial applications. The flow is generally characterized by a presence of secondary flow, vortical motions and pressure losses for different flow regimes. These observed irregularities may positively or negatively impact the flow. They are beneficial for cases where mixing of fluids is required, usually observed for multiphase flow regimes or detrimental for cases involving particles in the fluid. There are also instances where a particle-laden fluid transported through the curved pipe was directly related to corrosion- erosion related problems. …

Characterization Of Single- And Multi-Phase Shock-Accelerated Flows, Patrick John Wayne

Mechanical Engineering ETDs

Experiments conducted in the Shock Tube Facility at the University of New Mexico are focused on characterization of shock-accelerated flows. Single-phase (gaseous) initial conditions consist of a heavy gas column of sulfur hexafluoride seeded with approximately 11% acetone gas by mass. Visualization of the image plane for gaseous initial conditions is accomplished via planar laser-induced fluorescence (PLIF) with a high-powered Nd:YAG ultraviolet laser and an Apogee Alta U-42 monochrome CCD camera, with a quantum efficiency > 90%. Multi-phase (gas-solid) initial conditions consist of glass micro-beads deposited on small 1-cm diameter discs of specific surface chemistry, mounted flush with the bottom wall …

Flow-Induced Oscillations In Floating Offshore Wind Turbines, Daniel Carlson

Doctoral Dissertations

The goal of this thesis is to experimentally study the structural dynamics, wake interaction, and fluid forces on the multiple-degree of freedom systems typical of floating wind turbines. Vortex--surface alignment about flexibly-mounted prisms is studied to investigate the response of barges and semi-submersible hulls, and new results pertaining to the galloping response kink for a prism with dual inline--crossflow resonance is presented. Flow--induced oscillations of a spar model free to rotate in 3D space is replicated and observed as 2D figure--eight orbits about the center of the spar. Methods to suppress the flow from exciting the spar are proposed. The …

Meshless Modeling Of Flow Dispersion And Progressive Piping In Poroelastic Levees, Anthony Khoury, Eduardo Divo, Alain J. Kassab, Sai Kakuturu, Lakshmi Reddi

Publications

Performance data on earth dams and levees continue to indicate that piping is one of the major causes of failure. Current criteria for prevention of piping in earth dams and levees have remained largely empirical. This paper aims at developing a mechanistic understanding of the conditions necessary to prevent piping and to enhance the likelihood of self-healing of cracks in levees subjected to hydrodynamic loading from astronomical and meteorological (including hurricane storm surge-induced) forces. Systematic experimental investigations are performed to evaluate erosion in finite-length cracks as a result of transient hydrodynamic loading. Here, a novel application of the localized collocation …

Fluid Transport In Porous Media For Engineering Applications, Eric M. Benner

Chemical and Biological Engineering ETDs

This doctoral dissertation presents three topics in modeling fluid transport through porous media used in engineering applications. The results provide insights into the design of fuel cell components, catalyst and drug delivery particles, and aluminum- based materials. Analytical and computational methods are utilized for the modeling of the systems of interest. Theoretical analysis of capillary-driven transport in porous media show that both geometric and evaporation effects significantly change the time dependent behavior of liquid imbibition and give a steady state flux into the medium. The evaporation–capillary number is significant in determining the time-dependent behavior of capillary flows in porous media. …

High Resolution Validation Of Next Generation Turbulent Flow Models Using Neutron Beams, Laser Fluorescence, And Cryogenic Helium, Landen G Mcdonald

EURēCA: Exhibition of Undergraduate Research and Creative Achievement

Turbulent fluid flow is an incredibly unpredictable subject that continues to confound scientists and engineers. All of the empirical data that has been the basis of conventional turbulent computational fluid dynamics (CFD) models for decades only extends to roughly the equivalent turbulence created when Michael Phelps swims in a pool. The problem is that this data is then extrapolated out many orders of magnitude in order to design cruise ships, airplanes, and rockets which operate in significantly more turbulent flow regimes. This creates an incredible degree of uncertainty in the design process that demands over-engineering and increased expenditures.

The development …

Geospatial Energy Potential And Life Cycle Assessment Of Nearshore Oscillating Water Column Systems, Aleks Siemenn, Marie-Odile Fortier

CURCE Annual Undergraduate Conference

Oscillating Water Column (OWC) systems are an iteration of terminator ocean energy technology which generate electrical energy from turbine torque induced by the compression of air in a chamber from changing water level height. OWCs are a well-established technology, however, there have been no studies to date which quantify the life cycle environmental impacts of these systems in a geographic context. The goal of this study is to optimally size an OWC system for selected New England coastline sites and then assess the environmental impacts of the varying system sizes.

An OWC system is optimally sized when the volume of …

Modeling Multiphase Flow And Substrate Deformation In Nanoimprint Manufacturing Systems, Andrew Cochrane

Nanoscience and Microsystems ETDs

Nanopatterns found in nature demonstrate that macroscopic properties of a surface are tied to its nano-scale structure. Tailoring the nanostructure allows those macroscopic surface properties to be engineered. However, a capability-gap in manufacturing technology inhibits mass-production of nanotechnologies based on simple, nanometer-scale surface patterns. This gap represents an opportunity for research and development of nanoimprint lithography (NIL) processes. NIL is a process for replicating patterns by imprinting a fluid layer with a solid, nano-patterned template, after which ultraviolet cure solidifies the fluid resulting in a nano-patterned surface. Although NIL has been demonstrated to replicate pattern features as small as 4 …

Flame And Flow Characteristics Of A Plane-Jet Flame Modulated By A V-Shaped Fluidic Oscillator, Ching Min Hsu, Hsiu Feng Yang, Yuan Xu Zhang

Journal of Marine Science and Technology

The characteristic flame behaviors and velocity fields of a plane-jet flame modulated by a fluidic oscillator were experimentally studied. The flame behaviors were observed by the traditional photographic technique. The time-averaged velocity fields of the jet flame were measured by a high-speed particle image velocimeter. The temperature distributions of the jet flame were measured by an R-type thermocouple. The pulsating reacting jets issued from the side slots of the fluidic-oscillator burner formed two diffusion flames. By observing the flame behavior at around burner exit, three characteristic flame modes: attached flame, transitional flame, and lifted flame, were identified in the domain …

Direct Numerical Simulation Of Roughness Induced Hypersonic Boundary Layer Transition On A 7° Half-Angle Cone, Tara E. Crouch

Theses and Dissertations

Direct numerical simulation (DNS) computational fluid dynamic (CFD) calculations were performed on a 30° slice of 7° half-angle cones with increasing nose radii bluntness at Mach 10 while simulating a distributed roughness pattern on the cone surface. These DNS computations were designed to determine if the non-modal transition behavior observed in testing performed at the Arnold Engineering Development Center (AEDC) Hypervelocity Wind Tunnel 9 was induced via distributed surface roughness. When boundary layer transition is dominated by second mode instabilities, an increase in nose radius delays the transition location downstream. However, blunt nose experiments indicated that as the nose radius …

Analytical Models And Control Design Approaches For A 6 Dof Motion Test Apparatus, Kyra L. Schmidt

Theses and Dissertations

Wind tunnels play an indispensable role in the process of aircraft design, providing a test bed to produce valuable, accurate data that can be extrapolated to actual flight conditions. Historically, time-averaged data has made up the bulk of wind tunnel research, but modern flight design necessitates the use of dynamic wind tunnel testing to provide time-accurate data for high frequency motion. This research explores the use of a 6 degree of freedom (DOF) motion test apparatus (MTA) in the form of a robotic arm to allow models inside a subsonic wind tunnel to track prescribed trajectories to obtain time-accurate force …

Tracking Shock Movement On The Surface Of An Oscillating, Straked Semispan Delta Wing, Justin A. Pung

Theses and Dissertations

A recent research effort, sponsored by the Air Force Office of Scientific Research, numerically investigated the unsteady aerodynamic flow field around an oscillating, straked, delta wing. The study was centered on determining the importance of the unsteady aerodynamic forces acting as a driver for a nonlinear motion known as limit cycle oscillations. The current effort focused on creating a computational model to compare to the results of previous tests and modeling efforts and discover new information regarding the onset of LCO. The computational model was constructed using the Cartesian overset capabilities of the CREATE-AV™ fixed wing fluid dynamics solver Kestrel. …

Investigation Of Endwall Vortex Manipulation In High Lift Turbines Caused By Active Endwall Forcing, Horatio J. Babcock

Theses and Dissertations

With the increased demand for lighter, more fuel efficient and smaller gas turbine engines, the impetus to reduce the weight and size of the turbine has become apparent. One approach to reduce this weight is to reduce the number of blades in the turbine. However, to maintain power output, each blade must be capable of supporting a greater amount of lift. While several high-lift turbine profiles have been detailed in literature, most of these profiles have increased endwall losses, despite their desirable mid-span characteristics. To mitigate this endwall loss, a number of active and passive flow approaches have been studied …

Initial Stage Of Fluid-Structure Interaction Of A Celestial Icosahedron Shaped Vacuum Lighter Than Air Vehicle, Dustin P. Graves

Theses and Dissertations

The analysis of a celestial icosahedron geometry is considered as a potential design for a Vacuum Lighter than Air Vehicle (VLTAV). The goal of the analysis is ultimately to understand the initial fluid-structure interaction of the VLTAV and the surrounding airflow. Up to this point, previous research analyzed the celestial icosahedron VLTAV in relation to withstanding a symmetric sea-level pressure applied to the membrane of the structure. This scenario simulates an internal vacuum being applied in the worst-case atmospheric environmental condition. The next step in analysis is to determine the aerodynamic effects of the geometry. The experimental setup for obtaining …

Schlieren Imaging And Flow Analysis On A Cone/Flare Model In The Afrl Mach 6 Ludwieg Tube Facility, David A. Labuda

Theses and Dissertations

High-speed Schlieren photography was utilized to visualize flow in the Air Force Research Laboratory Mach 6 Ludwieg tube facility. A 7° half-angle cone/flare model with variable nosetip radius and flare angle options was used in the study. Testing was performed at two driver tube pressures, generating freestream Reynolds numbers of 10.0x10⁶ and 19.8x10⁶ per meter. The variable-angle flare portion of the model provided a method for adjusting the intensity of the adverse pressure gradient at the cone/flare junction. As expected from existing literature, boundary layer separation along the cone frustum occurred further upstream as the magnitude of the …

Examination Of Flow Dynamics And Passive Cooling In An Ultra Compact Combustor, Tylor C. Rathsack

Theses and Dissertations

The Ultra Compact Combustor (UCC) promises to greatly reduce the size of a gas turbine engine’s combustor by altering the manner in which fuel is burnt. Differing from the common axial flow combustor, the UCC utilizes a rotating flow, coaxial to the engine’s primary axis, in an outboard circumferential cavity as the primary combustion zone. The present study investigates two key UCC facets required to further this combustor design. The first area of investigation is cooling of the Hybrid Guide Vane (HGV). This UCC specific hardware acts as a combustor center body that alters the exit flow angle and acts …

Computational Aerothermodynamic Analysis Of Satellite Trans-Atmospheric Skip Entry Survivability, John J. Runco

Theses and Dissertations

Computational aerothermodynamic analysis is presented for a spacecraft in low Earth orbit performing an atmospheric skip entry maneuver. Typically, atmospheric reentry is a terminal operation signaling mission end-of-life and, in some instances, executed for spacecraft disposal. A variation on reentry – skip entry – is an aeroassisted trans-atmospheric maneuver in which a spacecraft utilizes the effects of aerodynamic drag in order to reduce energy prior to a terminal entry, pinpoint a targeted entry, or change orbital elements such as inclination. Spacecraft performing a skip entry enable new modes of maneuver to enhance operations in nominal or possibly contested mission environments. …

Wall Model Large Eddy Simulation Of A Diffusing Serpentine Inlet Duct, Ryan J. Thompson

Theses and Dissertations

The modeling focus on serpentine inlet ducts (S-duct), as with any inlet, is to quantify the total pressure recovery and ow distortion after the inlet, which directly impacts the performance of a turbine engine fed by the inlet. Accurate prediction of S-duct ow has yet to be achieved amongst the computational fluid dynamics (CFD) community to improve the reliance on modeling reducing costly testing. While direct numerical simulation of the turbulent ow in an S-duct is too cost prohibitive due to grid scaling with Reynolds number, wall-modeled large eddy simulation (WM-LES) serves as a tractable alternative. US3D, a hypersonic research …

Optimization And Control Of Arrays Of Wave Energy Converters, Jianyang Lyu

Dissertations, Master's Theses and Master's Reports

Wave Energy Converter Array is a practical approach to harvest ocean wave energy. To leverage the potential of the WEC array in terms of energy extraction, it is essential to have a properly designed array configuration and control system. This thesis explores the optimal configuration of Wave Energy Converters (WECs) arrays and their optimal control. The optimization of the WEC array allows both dimensions of individual WECs as well as the array layout to varying. In the first optimization problem, cylindrical buoys are assumed in the array where their radii and drafts are optimization parameters. Genetic Algorithms are used for …

Microfluidic Study Of Gravity-Driven Drainage And Coalescence Of Aqueous Two Dimensional Foams, Justin D. Heftel

Dissertations and Theses

Foams, a two-phase dispersion, are staples of the cosmetic, personal care, petroleum, pharmaceutical, and other industries. Central to these applications is the stability of the dispersion against separation. Foams break down by two mechanisms: the first is bubble coalescence, which is driven by the gravity drainage of the continuous phase. The drainage acts to push the bubbles against each other, and leads to the formation of thin lamellae, which break and cause the coalescence. The second is the mass transfer of the dispersed phase through the continuous phase, which is caused by the difference in pressures between the bubbles and …

Adhesion At Solid/Liquid Interfaces, Neda Ojaghlou

Theses and Dissertations

The adhesion at solid/liquid interface plays a fundamental role in diverse fields and helps explain the structure and physical properties of interfaces, at the atomic scale, for example in catalysis, crystal growth, lubrication, electrochemistry, colloidal system, and in many biological reactions. Unraveling the atomic structure at the solid/liquid interface is, therefore, one of the major challenges facing the surface science today to understand the physical processes in the phenomena such as surface coating, self-cleaning, and oil recovery applications. In this thesis, a variety of theory/computational methods in statistical physics and statistical mechanics are used to improve understanding of water adhesion …

A Study Of Several Applications Of Parallel Computing In The Sciences Using Petsc, Nicholas Stegmeier

Electronic Theses and Dissertations

The importance of computing in the natural sciences continues to grow as scientists strive to analyze complex phenomena. The dynamics of turbulence, astrophysics simulations, and climate change are just a few examples where computing is critical. These problems are computationally intractable on all computing platforms except supercomputers, necessitating the continued development of efficient algorithms and methodologies in parallel computing. This thesis investigates the use of parallel computing and mathematical modeling in the natural sciences through several applications, namely computational fluid dynamics for impinging jets in mechanical engineering, simulation of biofilms in an aqueous environment in mathematical biology, and the solution …

Call For Abstracts - Resrb 2019, July 8-9, Wrocław, Poland, Wojciech M. Budzianowski

Wojciech Budzianowski

No abstract provided.