Engineering Commons^™

Free-Space Measurements Of Dielectrics And Three-Dimensional Periodic Metamaterials, Clifford E. Kintner

Graduate Theses and Dissertations

This thesis presents the free-space measurements of a periodic metamaterial structure. The metamaterial unit cell consists of two dielectric sheets intersecting at 90 degrees. The dielectric is a polyetherimide-based material 0.001” thick. Each sheet has a copper capacitively-loaded loop (CLL) structure on the front and a cut-wire structure on the back. Foam material is used to support the unit cells. The unit cell repeats 40 times in the x-direction, 58 times in the y-direction and 5 times in the z-direction. The sample measures 12” × 12” × 1” in total. We use a free-space broadband system comprised of a pair …

Modeling And Simulation Of Iii-Nitride-Based Solar Cells Using Nextnano®, Malak Refaei

Graduate Theses and Dissertations

Nextnano³ software is a well-known package for simulating semiconductor band-structures at the nanoscale and predicting the general electronic structure. In this work, it is further demonstrated as a viable tool for the simulation of III-nitride solar cells. In order to prove this feasibility, the generally accepted solar cell simulation package, PC1D, was chosen for comparison. To critique the results from both PC1D and Nextnano3, the fundamental drift-diffusion equations were used to calculate the performance of a simple p-n homojunction solar cell device analytically. Silicon was picked as the material for this comparison between the outputs of the two simulators as …

A High Accuracy Microwave Radiometric Thermometer To Measure Internal Body Temperature, Michael D. Grady

USF Tampa Graduate Theses and Dissertations

The Center for Disease Control and Prevention (CDC) released heat illness data which highlighted that ~29 heat stress hospitalizations and ~3 heat-related deaths occurred every day during the summer months within the US from years 2000 to 2014. Heatstroke- the most severe form of heat illness which oftentimes lead to death- has been cited to be entirely preventable if a timely intervention is introduced. This dissertation uses microwave radiometric thermometry to perform wireless non-invasive internal body temperature monitoring which can enable intervention methods that help to prevent deaths associated with heat-illness.

Overall, this dissertation develops a comprehensive closed-form analytical radiometric …

Direct Digital Manufacturing Of Multi-Layer Wideband Ku-Band Patch Antennas, Merve Kacar

USF Tampa Graduate Theses and Dissertations

Design and performance of fully-printed Ku-band aperture coupled patch antennas fabricated by a direct digital manufacturing (DDM) approach that integrates fused deposition modeling (FDM) of acrylonitrile butadiene styrene (ABS) thermoplastic with in-situ micro-dispensing of conductive silver paste (CB028) are reported. Microstrip line characterizations are performed and demonstrate that misalignment of ABS substrate deposition direction with microstrip line micro-dispensing direction can degrade the effective conductivity up to 60% within the Ku-band, and must be taken into consideration in antenna array feed network designs. Specically, over 125 µm thick ABS substrate, RF loss of 0.052 dB/mm is obtained at 18 GHz, demonstrating …

Design And Simulation Of A Miniature Cylindrical Mirror Auger Electron Energy Analyzer With Secondary Electron Noise Suppression, Jay A. Bieber

USF Tampa Graduate Theses and Dissertations

In the nanoscale metrology industry, there is a need for low-cost instruments, which have the ability to probe the structrure and elemental composition of thin films. This dissertation, describes the research performed to design and simulate a miniature Cylindrical Mirror Analyzer, (CMA), and Auger Electron Spectrometer, (AES). The CMA includes an integrated coaxial thermionic electron source. Electron optics simulations were performed using the Finite Element Method, (FEM), software COMSOL. To address the large Secondary Electron, (SE), noise, inherent in AES spectra, this research also included experiments to create structures in materials, which were intended to suppress SE backgound noise in …

Design And Modeling Of A High-Power Periodic Spiral Antenna With An Integrated Rejection Band Filter, Jonathan M. O'Brien

USF Tampa Graduate Theses and Dissertations

This work details the design and fabrication of an ultra-wideband periodic spiral antenna (PSA) with a notch filter embedded directly into the radiating aperture. Prototype fabrication of the PSA reveals long assembly time due to forming the antenna element, therefore modifications are made to allow fabricating the antenna elements on a thin, flexible, Polyimide substrate. A transmission line model is develop to support the updated configuration of the antenna elements. In addition, a symmetric spurline filter is integrated into the arms of the spiral antenna in order to address the common problem of interference in ultra-wideband systems. For the first …

Analyses Of Densely Crosslinked Phenolic Systems Using Low Field Nmr, Jigneshkumar Patel

Doctoral Dissertations

A uniform dispersion of reactants is necessary to achieve a complete reaction involving multi-components, especially for the crosslinking of rigid high-performance materials. In these reactions, miscibility is crucial for curing efficiency. This miscibility is typically enhanced by adding a third component, a plasticizer. For the reaction of the highly crystalline crosslinking agent hexamethylenetetramine (HMTA) with a strongly hydrogen-bonded phenol formaldehyde resin, furfural has been traditionally used as the plasticizer. However, the reason for its effectiveness is not clear. In this doctoral thesis work, miscibility and crosslinking efficiency of plasticizers in phenolic curing reactions are studied by thermal analysis and spectroscopic …

Nanowire-Based Light-Emitting Diodes: A New Path Towards High-Speed Visible Light Communication, Mohsen Nami

Physics & Astronomy ETDs

Nano-scale optoelectronic devices have gained significant attention in recent years. Among these devices are semiconductor nanowires, whose dimeters range from 100 to 200 nm. Semiconductor nanowires can be utilized in many different applications including light-emitting diodes and laser diodes. Higher surface to volume ratio makes nanowire-based structures potential candidates for the next generation of photodetectors, sensors, and solar cells. Core-shell light-emitting diodes based on selective-area growth of gallium nitride (GaN) nanowires provide a wide range of advantages. Among these advantages are access to non-polar m-plane sidewalls, higher active region area compared to conventional planar structures, and reduction of threading …

Spatial Division Multiplexing Using Ince-Gaussian Beams, Sahil Sakpal

Electrical Engineering Theses and Dissertations

In space division multiplexing (SDM) the spatial modes of a multimode optical fiber are used as individual data channels. SDM gives another degree of freedom over wavelength for increasing data transmission rates. As a result, SDM is a potential solution for more than 400Gbit/s requirements in data centers where scaling data transmission rates with parallel single mode optical fibers is currently ubiquitous. However, due to mode coupling, i.e., spatial modes exchange of power, SDM may require multiple inputs multiple output digital signal processing (MIMO-DSP) to mitigate resulting mode crosstalk, the cost and complexity of which may be prohibited in data …

Quantum And Classical Optics Of Plasmonic Systems: 3d/2d Materials And Photonic Topological Insulators, Seyyed Ali Hassani Gangaraj

Theses and Dissertations

At the interface of two different media such as metal and vacuum, light can couple to the electrons of the metal to form a wave that is bound to the interface. This wave is called a surface plasmon-plariton (SPP), generally characterized by intense fields that decay quickly away from the interface. Due to their unique properties, SPPs have found a broad range of applications in various areas of science, including light harvesting, medical science, energy transfer and imaging. In addition to the widely studied classical plasmonics, quantum plasmonics is also attracting considerable interest in the electromagnetics and quantum optics communities. …

Two Senior Projects: 2.4 Ghz, 40% Efficiency Radio Frequency Amplifier, Ieee Design Contest, & Design And Implementation Of A Software Costas Loop For Audio Frequencies, Robert J. Tong

Electrical Engineering

How to Read this Document:

This document combines two senior project reports. The first senior project documents designing a class AB RF amplifier. The second, discusses the design and implementation of a software Costas loop for audio frequencies. The first report begins on the next page, while the Costas loop report starts on page 24. The two reports are orthogonal from one another. It is not a prerequisite to read the RF amplifier report before reading the Costas loop report. This document is merely two reports combined into one document. The second report, about the Costas loop, was written as …

Optimization Of Miniaturized Resonant Microwave Cavities For Use In Q-Thrusters, Joshua Steven Pennington

Graduate Theses and Dissertations

A gedankenexperiment was considered to compare a hypothetical thruster that used no reaction mass to propulsion methods currently in use. A brief discussion of previous research work done on closed resonant cavity thrust devices was conducted. Using the previous work as a template, a simulation plan was devised. Computational models of resonant microwave cavities were constructed and investigated using COMSOL software. These COMSOL simulations were verified against known analytical solutions using Matlab software as a computational tool. Multiphysics simulations were created to study the microwave heating environment of the resonant cavities. From the COMSOL study outputs, the electromagnetic field magnitude, …

Si-Based Germanium Tin Semiconductor Lasers For Optoelectronic Applications, Sattar H. Sweilim Al-Kabi

Graduate Theses and Dissertations

Silicon-based materials and optoelectronic devices are of great interest as they could be monolithically integrated in the current Si complementary metal-oxide-semiconductor (CMOS) processes. The integration of optoelectronic components on the CMOS platform has long been limited due to the unavailability of Si-based laser sources. A Si-based monolithic laser is highly desirable for full integration of Si photonics chip. In this work, Si-based germanium-tin (GeSn) lasers have been demonstrated as direct bandgap group-IV laser sources. This opens a completely new avenue from the traditional III-V integration approach. In this work, the material and optical properties of GeSn alloys were comprehensively studied. …

Microwave Interferometry Diagnostic Applications For Measurements Of Explosives, Loren A. Kline

Master's Theses

Microwave interferometry (MI) is a Doppler based diagnostic tool used to measure the detonation velocity of explosives, which has applications to explosive safety. The geometry used in existing MI experiments is cylindrical explosives pellets layered in a cylindrical case. It is of interest to Lawrence Livermore National Labs to measure additional geometries that may be overmoded, meaning that the geometries propagate higher-order transverse electromagnetic waves. The goal of my project is to measure and analyze the input reflection from a novel structure and to find a good frequency to use in an experiment using this structure. Two methods of determining …

Implementation Of Range Autofocus For Sar Radar Imaging, Nicholas J. Testin, Philip Davis

KSU Journey Honors College Capstones and Theses

The range calculation for an FMCW radar depends on accurate linear modulation. In some circumstances, linear modulation may not be available and must be corrected for. This paper describes an autofocus technique used to correct for phase error due to non-linearities in the components of a FMCW radar. Also described here is the algorithm used in calculating the phase error and application of the phase correction with triangle modulation. Known errors were calculated at certain distances and applied to correcting the phase of data taken at similar distances. The results given were generated using a SAR working outside linear ranges.

Development Of Intermediate Band Solar Cell Through Ingan Quantum Well Structures, Kelly Mckenzie

Electrical Engineering Undergraduate Honors Theses

In the search for high-efficiency solar cells, In_xGa_1-xN has come under scrutiny as a unique material with high potential. This is due to characteristics including an easily tunable bandgap, large range of potential bandgap values, and high heat resistance. However, one factor limiting its adaptation is the high density of crystal defects. In this thesis, the qualities of InGaN are discussed and the intermediate band solar cell structure is introduced. Additionally, the growth and characterization of two sets of InGaN-based solar cell devices are reported and evaluated.

Investigation Of Fes2 Nanoparticles For Use In Optoelectronic And Thermoelectric Applications, Rick Tefal Eyi Nkoghe

Graduate Theses and Dissertations

Iron pyrite (FeS2) is the most abundant sulfide material on earth. This material has been widely investigated by researchers because of its optical properties. However, it has been difficult to produce High efficiency FeS2 based solar cells. This is due to many different impurities that arise when making the materials. The ability to synthesize pure pyrite FeS2 material is therefore critical for applications.

Pure Iron pyrite nanocrystals were synthesized using hot injection by mixing sulfur with an iron precursor in the presence of an amine. To improve the stability, shorter ligands replaced the native amines ligands. The stability of the …

Novel Methods For The Time-Dependent Maxwell’S Equations And Their Applications, Sidney Shields

UNLV Theses, Dissertations, Professional Papers, and Capstones

This dissertation investigates three different mathematical models based on the time domain Maxwell's equations using three different numerical methods: a Yee scheme using a non-uniform grid, a nodal discontinuous Galerkin (nDG) method, and a newly developed discontinuous Galerkin method named the weak Galerkin (WG) method. The non-uniform Yee scheme is first applied to an electromagnetic metamaterial model. Stability and superconvergence error results are proved for the method, which are then confirmed through numerical results. Additionally, a numerical simulation of backwards wave propagation through a negative-index metamaterial is given using the presented method. Next, the nDG method is used to simulate …

Rural Broadband Mobile Communications: Spectrum Occupancy And Propagation Modeling In Western Montana, Erin Wiles

Graduate Theses & Non-Theses

Fixed and mobile spectrum monitoring stations were implemented to study the spectrum range from 174 to 1000 MHz in rural and remote locations within the mountains of western Montana, USA. The measurements show that the majority of this spectrum range is underused and suitable for spectrum sharing. This work identifies available channels of 5-MHz bandwidth to test a remote mobile broadband network. Both TV broadcast stations and a cellular base station were modelled to test signal propagation and interference scenarios.

Kasi: A Ka-Band And S-Band Cross-Track Interferometer, Gerard Ruiz Carregal

Masters Theses

A dual-frequency system is needed to better understand natural processes that constitute the environment and seasonal cycles of the Earth. A system working at two different wavelengths acquiring data simultaneously will give a valuable dataset since the conditions on the ground will be exactly the same. Hence, elements such as wind, soil moisture or any other changes on the ground will not interfere in the mea- surements. This thesis explains how an S-band radar was built and tested. Moreover, the experiments done with a Ka-band radar used as a scatterometer are explained as well as the data processing and analysis. …

Topography Measurements Using An Airborne Ka-Band Fmcw Interferometric Synthetic Aperture Radar, Kan Fu

Doctoral Dissertations

Radar interferometry at millimeter-wave frequencies has the ability of topography measurement of different types of terrain, such as water surfaces and tree canopies. A Ka-band interferometric radar was mounted on an airborne platform, and flown over the Connecticut river region in western Massachusetts near Amherst on June 11, 2012. More than 20 Gigabytes of raw data was recorded. This dissertation outline presents the results of the data processing, which includes (1) the estimation and removal of the embedded high frequency phase error in the raw data; (2) the synthetic aperture processing; (3) the interferometric processing. The digital elevation model (DEM) …

Engineered Nanocomposite Materials For Microwave/Millimeter-Wave Applications Of Fused Deposition Modeling, Juan De Dios Castro

USF Tampa Graduate Theses and Dissertations

A variety of high-permittivity (high-k) and low-loss ceramic-thermoplastic composite materials as fused deposition modeling (FDM) feedstock, based on cyclo-olefin polymer (COP) embedded with sintered ceramic fillers, have been developed and investigated for direct digital manufacturing (DDM) of microwave components. The composites presented in this dissertation use a high-temperature sintering process up to 1500°C to further enhance the dielectric properties of the ceramic fillers. The electromagnetic (EM) properties of these newly developed FDM composites were characterized up to the Ku-band by using the cavity perturbation technique. Several models for prediction of the effective relative dielectric permittivity of composites based …

Design Of Radio-Frequency Arrays For Ultra-High Field Mri, Ian R O Connell

Electronic Thesis and Dissertation Repository

Magnetic Resonance Imaging (MRI) is an indispensable, non-invasive diagnostic tool for the assessment of disease and function. As an investigational device, MRI has found routine use in both basic science research and medicine for both human and non-human subjects.

Due to the potential increase in spatial resolution, signal-to-noise ratio (SNR), and the ability to exploit novel tissue contrasts, the main magnetic field strength of human MRI scanners has steadily increased since inception. Beginning in the early 1980’s, 0.15 T human MRI scanners have steadily risen in main magnetic field strength with ultra-high field (UHF) 8 T MRI systems deemed to …

Picosecond Yb-Doped Fiber Amplifier, Weibin Zhu

Electronic Theses and Dissertations

Due to its versatility, rare earth doped fiber amplifier (RDFA) has attracted a lot of researchers worldwide in recent years. Depends on different kinds of rare earth ion, RDFA can be categorized into neodymium doped fiber amplifier (NDFA), erbium doped fiber amplifier (EDFA), thulium doped fiber amplifier (TDFA), and so forth. Among many kinds of RDFA, the ytterbium doped fiber amplifier (YDFA) has received even more interest, especially in high power application, mainly because of its broad gain bandwidth and high conversion efficiency which are due to its relatively simple electronic structure. The purpose of this research is to study …

Thermal And Waveguide Optimization Of Broad Area Quantum Cascade Laser Performance, Matthew Suttinger

Electronic Theses and Dissertations

Quantum Cascade Lasers are a novel source of coherent infrared light, unique in their tunability over the mid-infrared and terahertz range of frequencies. Advances in bandgap engineering and semiconductor processing techniques in recent years have led to the development of highly efficient quantum cascade lasers capable of room temperature operation. Recent work has demonstrated power scaling with broad area quantum cascade lasers by increasing active region width beyond the standard ~10 ?m. Taking into account thermal effects caused by driving a device with electrical power, an experimentally fitted model is developed to predict the optical power output in both pulsed …

Photothermal Lensing In Mid-Infrared Materials, Justin Cook

Electronic Theses and Dissertations

A thorough understanding of laser-materials interactions is crucial when designing and building optical systems. An ideal test method would probe both the thermal and optical properties simultaneously for materials under large optical loads where detrimental thermal effects emerge. An interesting class of materials are those used for infrared wavelengths due to their wide spectral transmission windows and large optical nonlinearities. Since coherent sources spanning the mid-wave and long-wave infrared wavelength regions have only become widely available in the past decade, data regarding their thermal and optical responses is lacking in literature. Photothermal Lensing (PTL) technique is an attractive method for …

High Dynamic Range Display Systems, Ruidong Zhu

Electronic Theses and Dissertations

High contrast ratio (CR) enables a display system to faithfully reproduce the real objects. However, achieving high contrast, especially high ambient contrast (ACR), is a challenging task. In this dissertation, two display systems with high CR are discussed: high ACR augmented reality (AR) display and high dynamic range (HDR) display. For an AR display, we improved its ACR by incorporating a tunable transmittance liquid crystal (LC) film. The film has high tunable transmittance range, fast response time, and is fail-safe. To reduce the weight and size of a display system, we proposed a functional reflective polarizer, which can also help …

Novel Photonic Resonance Arrangements Using Non-Hermitian Exceptional Points, Hossein Hodaei

Electronic Theses and Dissertations

In recent years, non-Hermitian degeneracies also known as exceptional points (EPs) have emerged as a new paradigm for engineering the response of optical systems. EPs can appear in a wide class of open non-Hermitian configurations. Among different types of non-conservative photonic systems, parity-time (PT) symmetric arrangements are of particular interest since they provide an excellent platform to explore the physics of exceptional points. In this work, the intriguing properties of exceptional points are utilized to address two of the long standing challenges in the field of integrated photonics- enforcing single mode lasing in intrinsically multimode cavities and enhancing the sensitivity …

Enhanced Ablation By Femtosecond And Nanoseond Pulses, Haley Kerrigan

Electronic Theses and Dissertations

Laser ablation of GaAs by a combination of femtosecond and nanosecond pulses is investigated as a means of enhancing material removal by a femtosecond pulse in the filamentation intensity regime. We demonstrate for the first time increased ablation of GaAs by ultrafast laser pulse plasmas augmented by nanosecond pulse radiation from a secondary laser. Material removal during laser ablation is a complex process that occurs via multiple mechanisms over several timescales. Due to different pulse durations, ablation by femtosecond and nanosecond pulses are dominated by different mechanisms. Ablation can be enhanced by optimally combining a femtosecond and nanosecond pulse in …

Laser-Induced Crystallization Mechanisms In Chalcogenide Glass Materials For Advanced Optical Functionality, Laura Sisken

Electronic Theses and Dissertations

Glass-ceramics (GC) are promising candidates for gradient refractive index (GRIN) optics. These multi-phase, composite materials also exhibit improved physical properties as compared to the parent base glass resulting from the formation of a secondary crystalline phase(s). Nanocrystal phase formation in a multi-component chalcogenide glass (ChG), (GeSe2-3As2Se3)(1-x)-(PbSe)x glass where x = 0-40 has been investigated, and the role of the starting material morphology has been correlated to the resulting composite's optical properties including refractive index, transmission, dispersion, and thermo-optic coefficient. Optical property evolution was related to the type and amount of the crystal phases formed, since through control of the local …