Engineering Commons^™

Testing And Packaging For Mems Acoustic Emission Sensors, Ting-Hung Liu

USF Tampa Graduate Theses and Dissertations

The goal of this research is to improve the structure and dimension of the MEMS acoustic emission sensor. Acoustic emission sensor (AE sensor) based on the piezoelectric transducer is a well-developed technology in non-destructive testing that is widely used to determine permanent damage such as cracks and corrosions in buildings and structures. The AE sensor can be used to monitor cracks in structures and to check leakage in pressurized systems. The location of cracks in a structure or system leakage causes a high-frequency surface vibration while releasing ultrasonic energy. The frequency of this energy is typically between 30 kHz to …

Electrical & Computer Engineering News, Georgia Southern University

Electrical & Computer Engineering News (2014-2023)

• Dr. Sungkyunn Lim, Array Antennas & Propagation Modeling

Modeling And Validation Of Local Electrowinning Electrode Current Density Using Two Phase Flow And Nernst-Planck Equations, Joshua M. Werner, W. Zeng, M. L. Free, Z. Zhang, J. Cho

Mining Engineering Faculty Publications

In this work we demonstrate the validity of a multi-physics model using COMSOL to predict the local current density distribution at the cathode of a copper electrowinning test cell. Important developments utilizing Euler-Euler bubbly flow with coupled Nernst-Planck transport equations allow additional insights into deposit characteristics and topographies.

Research On Power-Frequency Electromagnetic Interference Model Of Multicore Twisted Signal Cable Of High-Speed Railway, Bowen Zhang, Jiangjian Xie, Zhixin Wang, Jin Yang, Hao Yan

Turkish Journal of Electrical Engineering and Computer Sciences

With the increase in the traction power of high-speed railways, the power-frequency electromagnetic interference of traction current to the signal cables becomes increasingly more severe. In this paper, the calculation model of the magnetic interference to signal cable was established on the MATLAB/Simulink platform based on the multiconductor transmission line theory. This model took SPTYWPL03-8B 8-core twist signal cable as an example and the power-frequency interference of external current to the signal cable was analyzed theoretically. In addition, experiments on electromagnetic interference of double-ended and single-ended signal cables were performed to validate the simulation model. Experiments showed that the relative …

A New Semianalytical Method For Analysis Of The Disc-Type Permanent Magnethysteresis Motor In Steady-State Operational Conditions, Ali Behniafar, Ahmad Darabi

Turkish Journal of Electrical Engineering and Computer Sciences

Considering the characteristics of hysteresis and permanent magnet motors, it seems that these two motors are complements of each other. Thus, their combination yields a motor with an excellent performance. In order to preserve the major advantages of both motors in the new motor, a disc-type slotless structure is chosen. This paper presents a new finite-element method for the modeling of disc-type permanent magnet hysteresis synchronous (PMHS) motor. In this modeling method a new iterative algorithm is used. Programming software has been linked to finite- element software because of its limitation in the modeling of hysteresis phenomena. Validity of the …

Rlgc(F) Modeling Of A Busbar Distribution System Via Measured S-Parameters Atcenelec And Fcc Bands, Zeynep Hasirci, İsmai̇l Hakki Çavdar, Mehmet Öztürk

Turkish Journal of Electrical Engineering and Computer Sciences

This paper addresses the extraction of accurate frequency-dependent per-unit-length RLGC parameters for busbar distribution systems using measured S-parameters for the CENELEC and FCC bands. A busbar is a distribution system element (three phase, low voltage) with a modular structure that carries electrical energy in buildings. The S-parameters of a busbar distribution system at different current levels (630 A, 1250 A, 2000 A) are measured with a vector network analyzer and then analyzed for three different two-port connections (L1-N, L2-N, L3-N). A frequency- dependent RLGC(f) model is used to characterize the busbar as a transmission line using a derivative-free optimization algorithm. …