Engineering Commons^™

Triple-Junction Solar Cells : In Parallel., Levi C Mays

Electronic Theses and Dissertations

This paper looks into the current inefficiency of solar cells and attempts a few alternative solar cell structures in order to provide a more effective source of renewable energy. Currently, multi-junction solar cells are being developed to capture the sun’s light more efficiently. One of the ideas in this paper is to add a window to see if the addition of such a layer into a junction will increase the voltage while maintaining nearly the same current output. Central to this paper is the rearranging of the conducting layers of the multi-junction cell so that the junctions can be connected …

Design And Analysis Of A Non-Isolated High Gain Step-Up Cuk Converter, Yasser Almalaq

Electronic Theses and Dissertations

Renewable energy sources, such as solar energy, are desired for both economic and ecological issues. These renewable energy sources are plentiful in nature and have a terrific capability for power generation. The only drawback of solar energy, which is one of the best forms of energy sources, is that the output has a low voltage and needs to be stepped up in order to be inserted into the DC grid or an inverter for AC applications. To overcome this drawback, a high gain DC-DC power converter is required in this kind of system. These power converters are needed for a …

Application Of Silicon Nanohair Textured P-N Junctions In A Photovoltaic Device, Michael Small

Electronic Theses and Dissertations

The goal of this project is to design and develop a fabrication process for a silicon photovoltaic device which incorporates a nanohair textured p-n junction. The silicon nanowires are etched into a silicon wafer, comprising an epitaxial p-layer on n-substrate, via metal-assisted chemical etching (MACE). The resulting nanowires contain p-n junctions that lie along the length of the vertical nanowires. This construct has the potential to increase the optical bandwidth of a silicon photovoltaic device by allowing a greater amount of short wavelength light to reach the junction. In addition, the MACE method of nanofabrication has the potential for decreasing …

Synthesis And Characterization Of Kesterite Cu2znsns4 (Czts) Thin Films For Solar Cell Application, Mohamed M.A. Abusnina

Electronic Theses and Dissertations

The quaternary compound Cu₂ZnSnS₄ (CZTS) gained considerable attention in the last decade due to its potential as an active-layer semiconductor for low-cost thin-film solar cells. The material is composed of nontoxic and Earth-abundant constituents, has optical properties suitable for photovoltaic application, and can be synthesized using a wide variety of methods.

Polycrystalline CZTS was grown in this work using vacuum-based deposition to first deposit metal films (precursors) of Cu, Zn, and Sn. In a subsequent step, the precursors underwent an annealing treatment in sulfur vapor environment (sulfurization) to form CZTS. Using sputtering, a physical vapor deposition (PVD) …

Preparation And Characterization Of Cigss Solar Cells And Pv Module Data Analysis, Jyoti Shirolikar

Electronic Theses and Dissertations

In this thesis, multiple activities have been carried out in order to improve the process of CIGSS solar cell fabrication on a 4" x 4" substrate. The process of CIGSS solar cell fabrication at FSEC's PV Materials Lab involves a series of steps that were all carried out manually in the past. A LABVIEW program has been written to carry out automated sputter deposition of Mo back contact, CuGa, In metallic precursors on a soda lime glass substrate using a stepper motor control for better uniformity. Further, selenization/ sulfurization of these precursors was carried out using rapid thermal processing (RTP). …

Fpga-Based Design Of A Maximum-Power-Point Tracking System For Space A, Todd Persen

Electronic Theses and Dissertations

Satellites need a source of power throughout their missions to help them remain operational for several years. The power supplies of these satellites, provided primarily by solar arrays, must have high efficiencies and low weights in order to meet stringent design constraints. Power conversion from these arrays is required to provide robust and reliable conversion which performs optimally in varying conditions of peak power, solar flux, and occlusion conditions. Since the role of these arrays is to deliver power, one of the principle factors in achieving maximum power output from an array is tracking and holding its maximum-power point. This …