Engineering Commons^™

Field-Limited Migration Of Li-Ions In Li-Ion Battery, Fuqian Yang

Chemical and Materials Engineering Faculty Publications

The migration of Li-ions in lithium-ion battery cannot be simply described by Fick's second law; the interactions among ionic migration, field, and stress need to be taken into account when analyzing the migration of Li-ions. Using the theory of thermal activation process, the flux for ionic migration under concurrent action of electric field and mechanical stress is found to be a nonlinear function of the gradient of electric potential and the gradient of stress. Electric field can either accelerate or retard the growth of the lithiation layer, depending on polarity of the field.

Atomic Layer Deposition Of High Quality Hfo2 Using In-Situ Formed Hydrophilic Oxide As An Interfacial Layer, Lei Han, Jie Pan, Qinglin Zhang, Shibin Li, Zhi Chen

Electrical and Computer Engineering Faculty Publications

High-quality HfO₂ cannot be grown directly on Si substrate using atomic layer deposition (ALD), and an interfacial oxide layer is needed. Traditionally, interfacial oxide layer is formed either in SC1 solution (2 NH₄OH: 4 H₂O₂: 200 H₂O) or by ozonated water spraying. A highly hydrophilic SiO₂ interfacial layer was in-situ formed in the ALD chamber using 1 cycle of ozone and water. The HfO₂ deposited on this interfacial layer showed great growth linearity. The gate leakage current is comparable to that formed using chemical oxide as the interfacial layer. …

Near-Infrared Optical Absorption Enhanced In Black Silicon Via Ag Nanoparticle-Induced Localized Surface Plasmon, Peng Zhang, Shibin Li, Chunhua Liu, Xiongbang Wei, Zhiming Wu, Yadong Jiang, Zhi Chen

Electrical and Computer Engineering Faculty Publications

Due to the localized surface plasmon (LSP) effect induced by Ag nanoparticles inside black silicon, the optical absorption of black silicon is enhanced dramatically in near-infrared range (1,100 to 2,500 nm). The black silicon with Ag nanoparticles shows much higher absorption than black silicon fabricated by chemical etching or reactive ion etching over ultraviolet to near-infrared (UV-VIS-NIR, 250 to 2,500 nm). The maximum absorption even increased up to 93.6% in the NIR range (820 to 2,500 nm). The high absorption in NIR range makes LSP-enhanced black silicon a potential material used for NIR-sensitive optoelectronic device.

PACS

78.67.Bf; 78.30.Fs; 78.40.-q; 42.70.Gi

A Sensitive Film Structure Improvement Of Reduced Graphene Oxide Based Resistive Gas Sensors, Yong Zhou, Guangzhong Xie, Tao Xie, Huan Yuan, Huiling Tai, Yadong Jiang, Zhi Chen

Electrical and Computer Engineering Faculty Publications

This study was focused on how to improve the gas sensing properties of resistive gas sensors based on reduced graphene oxide. Sol-airbrush technology was utilized to prepare reduced graphene oxide films using porous zinc oxide films as supporting materials mainly for carbon dioxide sensing applications. The proposed film structure improved the sensitivity and the response/recovery speed of the sensors compared to those of the conventional ones and alleviated the restrictions of sensors' performance to the film thickness. In addition, the fabrication technology is relatively simple and has potential for mass production in industry. The improvement in the sensitivity and the …

Moisture Sensors On Conductive Substrates, Zhi David Chen, Ibrahim Yucedag

Electrical and Computer Engineering Faculty Patents

A moisture sensor includes a first electrode (a conductive substrate) having a first sensor portion and a first terminal portion as well as a second electrode having a second sensor portion and a second terminal portion. The moisture sensor also includes a layer of porous dielectric material sandwiched between the first sensor portion and the second sensor portion. Further the moisture sensor includes a layer of dense insulating material sandwiched between the first terminal portion and the second terminal portion. Leads are then connected to the two terminal portions.

Ferromagnetic Resonance Study Of Eightfold Artificial Ferromagnetic Quasicrystals, Vinayak Shantaram Bhat, J. Sklenar, J. Woods, B. Farmer, J. B. Ketterson, Jeffrey Todd Hastings, Lance E. De Long

Physics and Astronomy Faculty Publications

We have performed broadband (10 MHz–18 GHz) and narrowband (9.7 GHz) ferromagnetic resonance (FMR) measurements on permalloy thin films patterned with quasiperiodic Ammann tilings having eightfold rotational symmetry. We observed highly reproducible mode structures in the low-frequency, hysteretic regime in which domain walls and unsaturated magnetization textures exist. A minimum of 10 robust modes were observed in patterned samples, compared to the single uniform mode observed in unpatterned permalloy films. The field dependence and approximate eightfold rotational symmetry of the FMR spectra are in good agreement with micromagnetic simulations that confirm the importance of patterning for controlling static and dynamic …

Co2 Recycling Using Microalgae For The Production Of Fuels, Michael H. Wilson, John Groppo, Andrew Placido, S. Graham, S. A. Morton Iii, Eduardo Santillan-Jimenez, Aubrey Shea, Mark Crocker, Czarena Crofcheck, Rodney Andrews

Center for Applied Energy Research Faculty and Staff Publications

CO₂ capture and recycle using microalgae was demonstrated at a coal-fired power plant (Duke Energy’s East Bend Station, Kentucky). Using an in-house designed closed loop, vertical tube photobioreactor, Scenedesmus acutus was cultured using flue gas as the CO₂ source. Algae productivity of 39 g/(m² day) in June–July was achieved at significant scale (18,000 L), while average daily productivity slightly in excess of 10 g/(m² day) was demonstrated in the month of December. A protocol for low-cost algae harvesting and dewatering was developed, and the conversion of algal lipids—extracted from the harvested biomass—to diesel-range hydrocarbons via catalytic …

Influence Of Reduction Promoters On Stability Of Cobalt/Γ-Alumina Fischer-Tropsch Synthesis Catalysts, Gary Jacobs, Wenping Ma, Burtron H. Davis

Center for Applied Energy Research Faculty and Staff Publications

This focused review article underscores how metal reduction promoters can impact deactivation phenomena associated with cobalt Fischer-Tropsch synthesis catalysts. Promoters can exacerbate sintering if the additional cobalt metal clusters, formed as a result of the promoting effect, are in close proximity at the nanoscale to other cobalt particles on the surface. Recent efforts have shown that when promoters are used to facilitate the reduction of small crystallites with the aim of increasing surface Co⁰ site densities (e.g., in research catalysts), ultra-small crystallites (e.g., < 2–4.4 nm) formed are more susceptible to oxidation at high conversion relative to larger ones. The choice of promoter is important, as certain metals (e.g., Au) that promote cobalt oxide reduction can separate from cobalt during oxidation-reduction (regeneration) cycles. Finally, some elements have been identified to promote reduction but either poison the surface of Co⁰ (e.g., Cu), or produce excessive light gas selectivity (e.g., Cu and Pd, or Au at …

Investigation Of Protection Issues And Method For The Distribution System With Distributed Generations, Ke Xu

Theses and Dissertations--Electrical and Computer Engineering

Because DGs are introduced into distribution systems, the coordination of fuses and reclosers doesn’t work well. It means the original protection schemes are not available for the distribution systems with DGs. This thesis paper presents the study on the impacts of DGs on the fault current and voltage in the distribution system by the simulation of a model distribution system. After we study the impacts of DG on distribution systems, there is an introduction of current several current protection schemes and fault locations methods. At last, an adaptive protection scheme with a more efficient fault location method for the distribution …

Development Of Northrop-Grumman Mark Viie Training Unit And Wireless Video System For Use In Immersive Environments, Randall Lee Lewis

Theses and Dissertations--Electrical and Computer Engineering

A training unit has been developed that allows NVESD researchers to develop training simulations within virtual environments to enhance infantry skill and awareness. A ground station was developed to house a computer, power system, and video transmission system. This station will allow for a remote operator to wirelessly send a video/audio stream to the handset. The ground station also allows the use of external video and audio inputs to be sent using onboard converters. Different wireless frequencies were evaluated to determine the best for long-range transmission of content. A handset was developed from a carbon fiber prototype shell. The handset …

Virtualized Welding Based Learning Of Human Welder Behaviors For Intelligent Robotic Welding, Yukang Liu

Theses and Dissertations--Electrical and Computer Engineering

Combining human welder (with intelligence and sensing versatility) and automated welding robots (with precision and consistency) can lead to next generation intelligent welding systems. In this dissertation intelligent welding robots are developed by process modeling / control method and learning the human welder behavior.

Weld penetration and 3D weld pool surface are first accurately controlled for an automated Gas Tungsten Arc Welding (GTAW) machine. Closed-form model predictive control (MPC) algorithm is derived for real-time welding applications. Skilled welder response to 3D weld pool surface by adjusting the welding current is then modeled using Adaptive Neuro-Fuzzy Inference System (ANFIS), and compared …

A Universal Background Subtraction System, Hasan Sajid

Theses and Dissertations--Electrical and Computer Engineering

Background Subtraction is one of the fundamental pre-processing steps in video processing. It helps to distinguish between foreground and background for any given image and thus has numerous applications including security, privacy, surveillance and traffic monitoring to name a few. Unfortunately, no single algorithm exists that can handle various challenges associated with background subtraction such as illumination changes, dynamic background, camera jitter etc. In this work, we propose a Multiple Background Model based Background Subtraction (MB²S) system, which is universal in nature and is robust against real life challenges associated with background subtraction. It creates multiple background models …

Single Ended Traveling Wave Based Fault Location Using Discrete Wavelet Transform, Jin Chang

Theses and Dissertations--Electrical and Computer Engineering

In power transmission systems, locating faults is an essential technology. When a fault occurs on a transmission line, it will affect the whole power system. To find the fault location accurately and promptly is required to ensure the power supply. In this paper, the study of traveling wave theory, fault location method, Karrenbauer transform, and Wavelet transform is presented. This thesis focuses on single ended fault location method. The signal processing technique and evaluation study are presented. The MATLAB SimPowerSystem is used to test and simulate fault scenarios for evaluation studies.

Frequency Tracking And Phasor Estimation Using Least Squares And Total Least Squares Algorithms, Hengdao Guo

Theses and Dissertations--Electrical and Computer Engineering

System stability plays an important role in electric power systems. With the development of electric power system, the scale of the electric grid is now becoming larger and larger, and many renewable energy resources are integrated in the grid. However, at the same time, the stability and safety issues of electric power system are becoming more complicated. Frequency and phasors are two critical parameters of the system stability. Obtaining these two parameters have been great challenges for decades. Researchers have provided various kinds of algorithms for frequency tracking and phasor estimation. Among them, Least Squares (LS) algorithm is one of …

Functionalized Membranes For Environmental Remediation And Selective Separation, Li Xiao

Theses and Dissertations--Chemical and Materials Engineering

Membrane process including microfiltration (MF), ultrafiltration (UF), nanofiltration (NF) and reverse osmosis (RO) have provided numerous successful applications ranging from drinking water purification, wastewater treatment, to material recovery. The addition of functional moiety in the membranes pores allows such membranes to be used in challenging areas including tunable separations, toxic metal capture, and catalysis. In this work, polyvinylidene fluoride (PVDF) MF membrane was functionalized with temperature responsive (poly(N-isopropylacrylamide), PNIPAAm) and pH responsive (polyacrylic acid, PAA) polymers. It’s revealed that the permeation of various molecules (water, salt and dextran) through the membrane can be thermally or pH controlled. The introduction of …

Active Current Injection Method For Limiting Ground Fault Current Harmonics In Underground Coal Mines, Yigong Zhang

Theses and Dissertations--Mining Engineering

Current practice in U.S. underground coal mine high-voltage distribution systems is to attempt to limit ground fault current to 25 Amperes and de-energize the circuit at 10 Amperes. However, the significant amount of system capacitance due to the use of shielded cables can cause ground fault current to be two or three times the intended ground fault limit. Consequently, this practice can cause several issues such as ground fault currents significantly exceeding the neutral grounding resistor current limit, loss of relay selectivity in the distribution system, and transient overvoltages in certain ground fault situations. These issues are solved to some …

Robomirror: A Simulated Mirror Display With A Robotic Camera, Yuqi Zhang

Theses and Dissertations--Electrical and Computer Engineering

Simulated mirror displays have a promising prospect in applications, due to its capability for virtual visualization. In most existing mirror displays, cameras are placed on top of the displays and unable to capture the person in front of the display at the highest possible resolution. The lack of a direct frontal capture of the subject's face and the geometric error introduced by image warping techniques make realistic mirror image rendering a challenging problem. The objective of this thesis is to explore the use of a robotic camera in tracking the face of the subject in front of the display to …

Proposed Middleware Solution For Resource-Constrained Distributed Embedded Networks, Jason T. Rexroat

Theses and Dissertations--Electrical and Computer Engineering

The explosion in processing power of embedded systems has enabled distributed embedded networks to perform more complicated tasks. Middleware are sets of encapsulations of common and network/operating system-specific functionality into generic, reusable frameworks to manage such distributed networks. This thesis will survey and categorize popular middleware implementations into three adapted layers: host-infrastructure, distribution, and common services. This thesis will then apply a quantitative approach to grading and proposing a single middleware solution from all layers for two target platforms: CubeSats and autonomous unmanned aerial vehicles (UAVs). CubeSats are 10x10x10cm nanosatellites that are popular university-level space missions, and impose power and …

Model Analysis And Predictive Control Of Double Electrode Submerged Arc Welding Process For Fillet Joints With Root Opening, Yi Lu

Theses and Dissertations--Electrical and Computer Engineering

Submerged Arc Welding (SAW) for fillet joints is one of the major applications in the shipbuilding industry. Due to the requirement for the weld size, a sufficient amount of metal must be deposited. In conventional SAW process, the heat input is proportional to the amount of metal melted and is thus determined by the required weld size. To meet this requirement, an excessive amount of heat is applied causing large distortions on the welded structures whose follow-up straightening is highly costly. In order to reduce the needed heat input, Double-Electrode (DE) technology has been practiced creating the Double-Electrode SAW (DE-SAW) …

Efficient Anonymous Biometric Matching In Privacy-Aware Environments, Ying Luo

Theses and Dissertations--Electrical and Computer Engineering

Video surveillance is an important tool used in security and environmental monitoring, however, the widespread deployment of surveillance cameras has raised serious privacy concerns. Many privacy-enhancing schemes have been recently proposed to automatically redact images of selected individuals in the surveillance video for protection. To identify these individuals for protection, the most reliable approach is to use biometric signals as they are immutable and highly discriminative. If misused, these characteristics of biometrics can seriously defeat the goal of privacy protection. In this dissertation, an Anonymous Biometric Access Control (ABAC) procedure is proposed based on biometric signals for privacy-aware video surveillance. …

Modification Of Plasmonic Nano Structures' Absorption And Scattering Under Evanescent Wave Illumination Above Optical Waveguides Or With The Presence Of Different Material Nano Scale Atomic Force Microscope Tips, Gazi Mostafa Huda

Theses and Dissertations--Electrical and Computer Engineering

The interaction of an evanescent wave and plasmonic nanostructures are simulated in Finite Element Method. Specifically, the optical absorption cross section (C_abs) of a silver nanoparticle (AgNP) and a gold nanoparticle (AuNP) in the presence of metallic (gold) and dielectric (silicon) atomic force microscope (AFM) probes are numerically calculated in COMSOL. The system was illuminated by a transverse magnetic polarized, total internally reflected (TIR) waves or propagating surface plasmon (SP) wave. Both material nanoscale probes localize and enhance the field between the apex of the tip and the particle. Based on the absorption cross section equation the author …

Computational Multimedia For Video Self Modeling, Ju Shen

Theses and Dissertations--Computer Science

Video self modeling (VSM) is a behavioral intervention technique in which a learner models a target behavior by watching a video of oneself. This is the idea behind the psychological theory of self-efficacy - you can learn or model to perform certain tasks because you see yourself doing it, which provides the most ideal form of behavior modeling. The effectiveness of VSM has been demonstrated for many different types of disabilities and behavioral problems ranging from stuttering, inappropriate social behaviors, autism, selective mutism to sports training. However, there is an inherent difficulty associated with the production of VSM material. Prolonged …

Double-Electrode Arc Welding Process: Principle, Variants, Control And Developments, Yi Lu, Shujun Chen, Yu Shi, Xiangrong Li, Jinsong Chen, Lee Kvidahl, Yu Ming Zhang

Electrical and Computer Engineering Faculty Publications

Double-electrode gas metal arc welding (DE-GMAW) is a novel welding process in which a second electrode, non-consumable or consumable, is added to bypass part of the wire current. The bypass current reduces the heat input in non-consumable DE-GMAW or increases the deposition rate in consumable DE-GMAW. The fixed correlation of the heat input with the deposition in conventional GMAW and its variants is thus changed and becomes controllable. At the University of Kentucky, DE-GMAW has been tested/developed by adding a plasma arc welding torch, a GTAW (gas tungsten arc welding) torch, a pair of GTAW torches, and a GMAW torch. …

Nuclei/Cell Detection In Microscopic Skeletal Muscle Fiber Images And Histopathological Brain Tumor Images Using Sparse Optimizations, Hai Su

Theses and Dissertations--Computer Science

Nuclei/Cell detection is usually a prerequisite procedure in many computer-aided biomedical image analysis tasks. In this thesis we propose two automatic nuclei/cell detection frameworks. One is for nuclei detection in skeletal muscle fiber images and the other is for brain tumor histopathological images.

For skeletal muscle fiber images, the major challenges include: i) shape and size variations of the nuclei, ii) overlapping nuclear clumps, and iii) a series of z-stack images with out-of-focus regions. We propose a novel automatic detection algorithm consisting of the following components: 1) The original z-stack images are first converted into one all-in-focus image. 2) A …

Reference Compensation For Localized Surface-Plasmon Resonance Sensors, Neha Nehru

Theses and Dissertations--Electrical and Computer Engineering

Noble metal nanoparticles supporting localized surface plasmon resonances (LSPR) have been extensively investigated for label free detection of various biological and chemical interactions. When compared to other optical sensing techniques, LSPR sensors offer label-free detection of biomolecular interactions in localized sensing volume solutions. However, these sensors also suffer from a major disadvantage – LSPR sensors remain highly susceptible to interference because they respond to both solution refractive index change and non-specific binding as well as specific binding of the target analyte. These interactions can severely compromise the measurement of the target analyte in a complex unknown media and hence limit …

Prediction Model To Estimate The Zero Crossing Point For Faulted Waveforms, Md. Shakawat Hossan

Theses and Dissertations--Electrical and Computer Engineering

In any power system, fault means abnormal flow of current. Insulation breakdown is the cause of fault generation. Different factors can cause the breakdown: Wires drifting together in the wind, Lightning ionizing air, wires with contacts of animals and plants, Salt spray or pollution on insulators. The common type of faults on a three phase system are single line-to-ground (SLG), Line-to-line faults (LL), double line-to-ground (DLG) faults, and balanced three phase faults. And these faults can be symmetrical (balanced) or Unsymmetrical (imbalanced).In this Study, a technique to predict the zero crossing point has been discussed and simulated. Zero crossing point …

A Method For Non-Invasive, Automated Behavior Classification In Mice, Using Piezoelectric Pressure Sensors, Steven R. Gooch

Theses and Dissertations--Electrical and Computer Engineering

While all mammals sleep, the functions and implications of sleep are not well understood, and are a strong area of investigation in the research community. Mice are utilized in many sleep studies, with electroencephalography (EEG) signals widely used for data acquisition and analysis. However, since EEG electrodes must be surgically implanted in the mice, the method is high cost and time intensive. This work presents an extension of a previously researched high throughput, low cost, non-invasive method for mouse behavior detection and classification. A novel hierarchical classifier is presented that classifies behavior states including NREM and REM sleep, as well …

Machine-Human Cooperative Control Of Welding Process, Weijie Zhang

Theses and Dissertations--Electrical and Computer Engineering

An innovative auxiliary control system is developed to cooperate with an unskilled welder in a manual GTAW in order to obtain a consistent welding performance. In the proposed system, a novel mobile sensing system is developed to non-intrusively monitor a manual GTAW by measuring three-dimensional (3D) weld pool surface. Specifically, a miniature structured-light laser amounted on torch projects a dot matrix pattern on weld pool surface during the process; Reflected by the weld pool surface, the laser pattern is intercepted by and imaged on the helmet glass, and recorded by a compact camera on it. Deformed reflection pattern contains the …

Multi-Domain, Multi-Objective-Optimization-Based Approach To The Design Of Controllers For Power Electronics, Jing Shang

Theses and Dissertations--Electrical and Computer Engineering

Power converter has played a very important role in modern electric power systems. The control of power converters is necessary to achieve high performance. In this study, a dc-dc buck converter is studied. The parameters of a notional proportional-integral controller are to be selected. Genetic algorithms (GAs), which have been widely used to solve multi-objective optimization problems, is used in order to locate appropriate controller design. The control metrics are specified as phase margin in frequency domain and voltage error in time-domain. GAs presented the optimal tradeoffs between these two objectives. Three candidate control designs are studied in simulation and …

Multifrequency Averaging In Power Electronic Systems, Fei Pan

Theses and Dissertations--Electrical and Computer Engineering

Power electronic systems have been widely used in the electrical power processing for applications with power levels ranging from less than one watt in battery-operated portable devices to more than megawatts in the converters, inverters and rectifiers of the utility power systems. These systems typically involve the passive elements such as inductors, capacitors, and resistors, the switching electronic components such as IGBTs, MOSFETS, and diodes, and other electronic circuits. Multifrequency averaging is one of the widely used modeling and simulation techniques today for the analysis and design of power electronic systems. This technique is capable of providing the average behavior …