Engineering Commons^™

Method Of Optimal Battery Scheduling With Optimal Battery And Photovoltaic Sizing, Gideon Hallman

Masters Theses

“Renewable energy generation is on the rise. One of the best ways to capitalize on this intermittent power supply is by using the renewable energy source in tandem with batteries. A joint photovoltaic (PV) and battery system model was created that implemented battery degradation and optimized battery usage using a Markov Decision Process (MDP). This system was then subjected to a series of tests to do a sensitivity analysis while optimizing the battery and PV sizing for the system at hand. Parametric sweeps of solar power and battery capital costs, the cost of energy taken from the grid, the cost …

A Physics-Based Pi Pre-Layout Tool For Pcb Pdn Design, Shuang Liang

Masters Theses

"With increasingly stringent requirements for lower voltage supply, and higher density in PCB PDN design, now integrity (PI) is an increasingly important aspect that must be considered. A pre-layout tool based on the Cavity Model and Boundary Element Method is built to automatically achieve a specified target impedance for a multi-layered Printed Circuit Board (PCB) Power Distribution Network (PDN) design with a minimal number of decoupling capacitors.

The pre-work about the post-layout design and analysis is proposed and the guidelines for creating a decoupling capacitors network with better performance has been built. With limit inputs, physical limitations for the minimal …

Design And Evaluation Of The 3d Printed Electromagnetic Absorber Built With Conductive Carbon-Filled Filament, Rui Mi

Masters Theses

"This research presents an application of the resistive frequency selective surface (FSS) fabricated with a 3D printed conductive material as an electromagnetic absorber for the EMI-reducing door. This solution allows to reduce radiated emissions of a router system. The resistive frequency selective surface has a three-layer structure. The top layer is a 3D printed FSS pattern, the middle layer is an air gap, and the bottom layer is a metal plane.

The first paper presents the methodology for manufacturing a frequency selective surface using the 3D printing technology, including the material characterization, design, fabrication, and evaluation.

The unpublished content presents …

Analysis And Design Of Dc-Link Capacitor In Cascaded H-Bridge Multilevel Active Front-End Converter, Muhammad Shehroz Malik

Masters Theses

Medium-voltage grid-tied systems often use a cascaded H-bridge multi-level active front-end. In this converter, dc link bus capacitors play an important role in stabilizing the converter and enabling both active and reactive power injections. The present work provides analytical expressions for the capacitor current, which are essential for optimizing system design (especially capacitor size vs. lifetime). Then, the expression is incorporated into the grid connected bidirectional power system model. Consequently, this work contributes to the guiding principles to choose accurate dc link capacitor ratings against grid-side power delivery requirements.

DC-link capacitors come with an expiration date which is dependent on …

The Field Coupling Mechanism Study For Near Field Probe, Shun Liu

Masters Theses

"In this part, the radius of the loop is used to predict the voltage induced by the E- field in the circular loop antenna. The thin rectangle loop and thick rectangle loop have been investigated. The equivalent radius of the rectangle loop is estimated by the average of the one over the distance between the points on the loop to the center of the loop. The estimation matches with the numerical simulation"--Abstract, page iv.

A Simple Background Elimination Method For Miniaturized Fiber-Optic Raman Probe, Bohong Zhang

Masters Theses

"Raman scattering is called a photonic - molecular interaction based on the kinetic model of the analytic. Due to the uniqueness of the Raman scattering technique, it can provide a unique fingerprint signal for molecular recognition. However, a serious challenge often encountered in Raman measurement comes from the requirements of fast, real-time remote sensing, background fluorescence suppression, and micro-environmental detection.

A new Miniaturized Fiber-Optic Raman Probe (MFORP) for Raman spectroscopy, used especially for eliminating background fluorescence and enhancing sampling, is presented. Its main purpose is to provide an overview of excellent research on the detection of very small substances and …

Seed Modeling Of An Esd Gun Discharge To A Usb Cable, Yang Xu

Masters Theses

“An IC protected by a transient voltage suppression (TVS) diode may fail if the TVS device does not turn on or does not turn on quickly enough, causing the IC to take the full brunt of the electrostatic discharge (ESD) event. Transient simulation models have been developed for ESD protection devices for the purpose of system-efficient ESD design (SEED). The TVS modeling methodology has been improved to better represent the physics that occurs during the TVS response and more accurately predict the interactions between off-chip and on-chip protection devices. Moreover, a complicated test scenario -- an ESD gun discharge through …

A Compact Wavelength Meter Using A Multimode Fiber, Ogbole Collins Inalegwu

Masters Theses

“Wavelength meters are very important for precision measurements of both pulses and continuous-wave optical sources. Conventional wavelength meters employ gratings, prisms, interferometers, and other wavelength-sensitive materials in their design. Here, we report a simple and compact wavelength meter based on a section of multimode fiber and a camera. The concept is to correlate the multimodal interference pattern (i.e., speckle pattern) at the end-face of a multimode fiber with the wavelength of the input lightsource. Through a series of experiments, specklegrams from the end face of a multimode fiber as captured by a charge-coupled device (CCD) camera were recorded; the images …

Bond Graph Modeling Of Critical Infrastructures For Cyber-Physical Security Implementation, Michele Jane White

Masters Theses

“In developed societies, there exists infrastructure vital to everyday life. This includes water and power systems. Technology is quickly evolving and being implemented on these utilities. This technology can range from smart metering in neighborhoods to volume sensors in local waste water treatment facilities. When networking, sensing, monitoring, or control devices are integrated with infrastructure it is considered a cyber physical system, or CPS. When information about an important physical system is connected to the virtual world, it is opened up to security risks. Cyber security can be provided to the CPS by monitoring the physical state of the system …

Physics-Based Modeling Of Lithium-Ion Batteries For Control And Estimation Applications, Brody J. C. Riemann

Masters Theses

“Lithium-ion batteries are extensively used in many application areas like consumer electronics, electric vehicles, and microgrids. As the world moves towards further electrification of vehicles and more widespread use of renewable energy sources, the need for large-scale battery storage systems will grow. To effectively replace conventional methods, batteries will need to be charged quickly while accounting for degradation to maximize lifetime. Further, larger batteries require more detailed safety monitoring, which is implemented using a battery management system (BMS). A BMS is responsible for state of charge (SOC) estimation, state of health (SOH) estimation, cell balancing, regulating voltage and current according …

Transfer Function Measurement For Automotive Intentional Emi And Thermal Runaway Investigation Of Lithium-Ion Battery By Intentional Emi, Woncheol Song

Masters Theses

"With an increasing demand for electric vehicles and autonomous driving, many components of a vehicle are being replaced as electric components. This implicates the possibility of an increase in the malfunction of electric components due to unknown electromagnetic interferences. In this reason, malicious intentional electromagnetic interference (IEMI) is being considered as a growing threat for the current and next generation of automotive technology.

In the first topic, the transfer function between the IEMI attacker and the engine control unit (ECU) circuit in an automobile is extracted to analyze how the IEMI affects the vehicle.

In the second topic, to mimic …