Engineering Commons^™

Milliwatt Power Deep Ultraviolet Light-Emitting Diodes Over Sapphire With Emission At 278 Nm, J. P. Zhang, A. Chitnis, V. Adivarahan, S. Wu, V. Mandavilli, R. Pachipulusu, M. Shatalov, Grigory Simin, J. W. Yang, M. Asif Khan

Faculty Publications

We report on AlGaN multiple-quantum-well (MQW)-based deep ultraviolet light-emitting diodes over sapphire with peak emission at 278 nm. A new buffer layer growth process was used to reduce the number of defects and hence the nonradiative recombination. The improved material quality and carrier confinement resulted in pulsed powers as high as 3 mW at 278 nm and a significantly reduced deep-level-assisted long-wavelength emission.

Chaotic Free-Space Laser Communication Over Turbulent Channel, N. F. Rulkov, Mikhail Vorontsov, L. Illing

Electro-Optics and Photonics Faculty Publications

The dynamics of errors caused by atmospheric turbulence in a self-synchronizing chaos-based communication system that stably transmits information over a ∼5  km free-space laser link is studied experimentally. Binary information is transmitted using a chaotic sequence of short-term pulses as a carrier. The information signal slightly shifts the chaotic time position of each pulse depending on the information bit. We report the results of an experimental analysis of the atmospheric turbulence in the channel and the impact of turbulence on the bit-error-rate performance of this chaos-based communication system.

Buffer Interference Architecture, Vladimir I. Prodanov

Electrical Engineering

An up to 3× breakdown voltage tristate capable integrated circuit CMOS buffer includes a level shifter circuit and a driver circuit. The driver stage includes a series connected n-channel and p-channel cascode stacks, each including at least three transistors. Dynamic gate biasing is provided for the third n-channel and p-channel cascode transistors to prevent voltage overstress of the cascode transistors. The level shifter circuit includes at least one pseudo N-MOS inverter including an input transistor, a protective cascode stack including at least one n-channel cascode transistor, and a load transistor. The level shifter provides at least one voltage shifted input …

An Assessment Of Seawinds On Quikscat Wind Retrieval, David Draper, David G. Long

Faculty Publications

The scatterometer ocean wind retrieval process produces several possible solutions or ambiguities at each point, requiring a separate ambiguity selection step to infer a unique wind vector field. An ambiguity selection error occurs when the selected wind vector is not the closest ambiguity to the true wind. The current ambiguity selection routine for SeaWinds is ad hoc, but performs well under most circumstances. Factors such as instrument noise and rain can also cause the estimated wind flow to deviate from the true wind. A quality assurance (QA) analysis is performed to assess the ambiguity selection effectiveness and noise level of …

An Optimum Greedy Algorithm For Choosing Minimal Set Of Conflicting Constraints In The Point Sequencing Problem, Florent Launay, Mitra Debasis

Electrical Engineering and Computer Science Faculty Publications

In this work, we first have proposed a technique to define the "causes" of inconsistency on an online point based reasoning constraint network. Second, we introduce an algorithm that proposes the user a minimal set of relations to remove when inconsistencies are detected. We have developed and implemented a battery of algorithms for the purpose of this type of reasoning. Some useful theorems and properties are defined for proving the 'minimal' aspect of the algorithm. Finally, we found that our investigation was a polynomially solvable sub problem of the vertex cover problem.

Dynamic Yield Analysis And Enhancement Of Fpga Reconfigurable Memory Systems, Minsu Choi, Nohpill Park

Electrical and Computer Engineering Faculty Research & Creative Works

This paper addresses the issues of field programmable gate arrays (FPGA) reconfigurable memory systems with faulty physical memory cells and proposes yield measurement techniques. Static yield (i.e., the yield which does not take into account the inherited redundancy utilization for repair) and dynamic yield (i.e., the yield which takes into account the inherited redundancy utilization for repair) of FPGA reconfigurable memory systems and their characteristics are extensively analyzed. Yield enhancement of conventional memory systems relies on additional redundancy, but FPGA reconfigurable memory systems have inherited redundancy and customizability. Thus, they can accommodate numerous target memory configurations, and redundant memory cells, …

Training Fuzzy Systems With The Extended Kalman Filter, Daniel J. Simon

Electrical and Computer Engineering Faculty Publications

The generation of membership functions for fuzzy systems is a challenging problem. We show that for Mamdani-type fuzzy systems with correlation-product inference, centroid defuzzification, and triangular membership functions, optimizing the membership functions can be viewed as an identification problem for a nonlinear dynamic system. This identification problem can be solved with an extended Kalman filter. We describe the algorithm and compare it with gradient descent and with adaptive neuro-fuzzy inference system (ANFIS) based optimization of fuzzy membership functions. The methods discussed in this paper are illustrated on a fuzzy filter for motor winding current estimation, and are compared with Butterworth …

Implementation Of Gy-Eq For Deterministic Effects Limitation In Shield Design, John W. Wilson, Myung-Hee Y. Kim, Giovanni De Angelis, Francis A. Cucinotta, Nobuaki Yoshizawa, Francis F. Badavi

Mathematics & Statistics Faculty Publications

The NCRP has recently defined RBE values and a new quantity (Gy-Eq) for use in estimation of deterministic effects in space shielding and operations. The NCRP's RBE for neutrons is left ambiguous and not fully defined. In the present report we will suggest a complete definition of neutron RBE consistent with the NCRP recommendations and evaluate attenuation properties of deterministic effects (Gy-Eq) in comparison with other dosimetric quantities.

Polarization Effects In Photoluminescence Of C- And M-Plane Gan/Algan Multiple Quantum Wells, E. Kuokstis, C. Q. Chen, M. E. Gaevski, W. H. Sun, J. W. Yang, Grigory Simin, M. Asif Khan, H. P. Maruska, D. W. Hill, M. C. Chou, J. J. Gallagher, B. Chai

Faculty Publications

Polarizationeffects have been studied in GaN/AlGaN multiple quantum wells(MQWs) with different c-axis orientation by means of excitation-dependent photoluminescence(PL) analysis. Quantum structures were grown on [0001]-oriented sapphire substrates (C plane) and single-crystalline [11̄00]-oriented freestanding GaN (M plane) using the metalorganic chemical vapor deposition technique. Strong PL spectrum line blueshifts (up to 140 meV) which are correlated with the excitation intensity have been obtained for C-plane MQWs, whereas no shift has been observed for M-plane MQWs.Theoretical calculations and comparison with the PL data confirm that the built-in electric field for C-plane structures is much stronger than the field present for M-plane MQWs. …

Determination Of Whole-Body Specific Absorption Rate (Sar) And Characterization Of Ferris Wheel Radio Frequency (Rf) Exposure System Using Calorimetric Techniques, Subbarao V. Chebrolu

FIU Electronic Theses and Dissertations

The "Ferris Wheel" RE Exposure System was designed by Motorola Inc. to study the long-term biological effects due to RE exposure [3]. The main goal of this research project was to characterize the "Ferris Wheel" to know how efficient and symmetrical was the exposure system in distributing the RE power among its loads. The characterization of the system was done in terms of power efficiency, SAR, Whole-Body SAR and Localized SAR.

Exposure to RF sources is quantified in terms of SAR which defines the rate of electromagnetic deposition per unit mass. Determination of Whole-Body averaged SAR requires to have the …

Illuminating Electronics Problem Solving With The Cal Poly Mohat Technique, David Braun, Fred W. Depiero, Michael Borland

Electrical Engineering

This paper describes a Cal Poly version of circuit analysis to assist both students and instructors. The primary focus of the technique is helping students perform hand analysis, particularly the type of hand analysis that clarifies the student’s understanding of circuit operation in a manner that can benefit subsequent design decisions. The technique nicely complements graphical solution techniques such as load-line analyses and computer aided circuit simulation. MoHAT, an abbreviation of Model-Hypothesize-Analyze-Test, provides students with a roadmap to use, when analyzing even relatively complex circuits containing diodes and transistors. This paper emphasizes the pedagogy of MoHAT and describes a web-based …

Source Localization In A Time-Varying Ocean Waveguide, Cristiano Soares, Martin Siderius, Sérgio M. Jesus

Electrical and Computer Engineering Faculty Publications and Presentations

One of the most stringent impairments in matched-field processing is the impact of missing or erroneous environmental information on the final source location estimate. This problem is known in the literature as model mismatch and is strongly frequency dependent. Another unavoidable factor that contributes to model mismatch is the natural time and spatial variability of the ocean waveguide. As a consequence, most of the experimental results obtained to date focus on short source-receiver ranges (usually <5 >km), stationary sources, reduced time windows and frequencies generally below 600 Hz. This paper shows that MFP source localization can be made robust to time–space …

Numerical Simulation Of Partial Discharge Propagation In Cable Joints Using The Finite Difference Time Domain Method, David Pommerenke, R. Jobava, R. Heinrich

Electrical and Computer Engineering Faculty Research & Creative Works

In this second of a series of three papers, the authors investigate partial discharge (PD) detection and propagation in cable joints. The complex nature of cable joints leads to errors when PD analysis is carried out using conventional equivalent circuits. The authors use the finite difference time domain method to determine the transient electromagnetic fields caused by simulated PD in model cable joints.

Gan Homoepitaxy On Freestanding (11̄00) Oriented Gan Substrates, C. Q. Chen, M. E. Gaevski, W. H. Sun, E. Kuokstis, J. P. Zhang, R. S. Q. Fareed, H. M. Wang, J. W. Yang, Grigory Simin, M. A. Khan, Herbert-Paul Maruska, David W. Hill, Mitch M. C. Chou, Bruce Chai

Faculty Publications

We report homoepitaxialGaNgrowth on freestanding (11̄00) oriented (M-plane GaN) substrates using low-pressure metalorganic chemical vapor deposition.Scanning electron microscopy,atomic-force microscopy, and photoluminescence were used to study the influence of growth conditions such as the V/III molar ratio and temperature on the surface morphology and optical properties of the epilayers. Optimized growth conditions led to high quality (11̄00) oriented GaN epilayers with a smooth surface morphology and strong band-edge emission. These layers also exhibited strong room temperature stimulated emission under high intensity pulsed optical pumping. Since for III-N materials the (11̄00) crystal orientation is free from piezoelectric or spontaneous polarization electric fields, …

Optical Constants And Roughness Study Of Dc Magnetron Sputtered Iridium Films, Li Yan, John A. Woollam

Department of Electrical and Computer Engineering: Faculty Publications

Extremely smooth thin films of iridium have been deposited onto superpolished fused silica substrates using dc magnetron sputtering in an argon plasma. The influence of deposition process parameters on film microroughness has been investigated. In addition, film optical constants have been determined using variable angle spectroscopic ellipsometry, over the spectral range from vacuum ultraviolet to middle infrared (140 nm–35 μm). Because the Ir films were optically thick and the surface roughnesses were measured by atomic force microscopy then accounted for in the optical model, the as-determined film optical constants are expected to be the best available for Ir bulk metals, …

Low-Temperature Operation Of Alfan Single-Quantum-Well Light-Emitting Diodes With Deep Ultraviolet Emission At 285 Nm, A. Chitnis, R. Pachipulusu, V. Mandavilli, M. Shatalov, E. Kuokstis, J. P. Zhang, V. Adivarahan, S. Wu, Grigory Simin, M. Asif Khan

Faculty Publications

We present a study of the electrical and optical characteristics of 285 nm emission deep ultraviolet light-emitting diodes(LED) at temperatures from 10 to 300 K. At low bias, our data show the tunneling carrier transport to be the dominant conduction mechanism. The room-temperature performance is shown to be limited mostly by poor electron confinement in the active region and a pronounced deep level assisted recombination but not by the hole injection into the active region. At temperatures below 100 K, the electroluminescence peak intensity increases by more than one order of magnitude indicating that with a proper device design and …

Learning Implicit User Interest Hierarchy For Context In Personalization, Philip K. Chan, Hyoung-Rae Kim

Electrical Engineering and Computer Science Faculty Publications

To provide a more robust context for personalization, we desire to extract a continuum of general (long-term) to specific (short-term) interests of a user. Our proposed approach is to learn a user interest hierarchy (UIH) from a set of web pages visited by a user. We devise a divisive hierarchical clustering (DHC) algorithm to group words (topics) into a hierarchy where more general interests are represented by a larger set of words. Each web page can then be assigned to nodes in the hierarchy for further processing in learning and predicting interests. This approach is analogous to building a subject …

Training Radial Basis Neural Networks With The Extended Kalman Filter, Daniel J. Simon

Electrical and Computer Engineering Faculty Publications

Radial basis function (RBF) neural networks provide attractive possibilities for solving signal processing and pattern classification problems. Several algorithms have been proposed for choosing the RBF prototypes and training the network. The selection of the RBF prototypes and the network weights can be viewed as a system identification problem. As such, this paper proposes the use of the extended Kalman filter for the learning procedure. After the user chooses how many prototypes to include in the network, the Kalman filter simultaneously solves for the prototype vectors and the weight matrix. A decoupled extended Kalman filter is then proposed in order …

Range-Dependent Seabed Characterization By Inversion Of Acoustic Data From A Towed Receiver Array, Martin Siderius, Peter L. Nielsen, Peter Gerstoft

Electrical and Computer Engineering Faculty Publications and Presentations

The MAPEX2000 experiments were conducted in the Mediterranean Sea in March, 2000 to determine seabed properties using a towed acoustic source and receiver array. Towed systems are advantageous because they are easy to deploy from a ship and the moving platform offers the possibility for estimating spatially variable (range-dependent) seabed properties. In this paper, seabed parameters are determined using a matched-field geoacoustic inversion approach with measured, towed array data. Previous research has successfully applied matched-field geoacoustic inversion techniques to measured acoustic data. However, in nearly all cases the inverted data were collected on moored, vertical receiver arrays. Results here show …

Metrics-Based Framework For Decision Making In Cots-Based Software Systems, Sahra Sedigh, Arif Ghafoor, Raymond A. Paul

Electrical and Computer Engineering Faculty Research & Creative Works

The growing reliance on Commercial-Off-The-Shelf (COTS) components for developing large-scale projects introduces a new paradigm in software Engineering; which requires the design of new software development and business processes. Large scale component reuse leads to savings in development resources, enabling these resources to be applied to areas such as quality improvement. These savings come at the price of integration difficulties, performance constraints, and incompatibility of components from multiple vendors. Relying on COTS components also increases the system's vulnerability to risks arising from third-party development, which can negatively affect the quality of the system, as well as causing expenses not incurred …

Application Of Maxwell Solvers To Pd Propagation. I. Concepts And Codes, David Pommerenke, S. Sakaguchi

Electrical and Computer Engineering Faculty Research & Creative Works

This article reviews the basic approaches to solving electromagnetic propagation in the context of PD detection. It also investigates available commercial software, introduces the steps required to obtain trustworthy computational results, and gives an example of detailed analysis of PD propagation.

Recurring Beams In Hollow Metal Waveguides: Paraxial Approximation, Lee W. Casperson

Electrical and Computer Engineering Faculty Publications and Presentations

For optical and near-optical applications in electromagnetics, the directed propagation of waves in free space and in lenslike media is often in the Cartesian form of Gaussian or more general Hermite-sinusoidal-Gaussian beams. It has been shown that recurring (rather than continuing) forms of such beams are possible in the paraxial approximation for certain hollow metal waveguides, in which multiple reflections from the waveguide walls may occur. Limitations on this recurrence behavior implicit in use of the paraxial approximation are considered here, and estimates are obtained for the maximum propagation distance before the onset of significant distortion of the recurring beams.

Near-Band-Edge Photoluminescence Of Wurtzite-Type Aln, E. Kuokstis, J. Zhang, Q. Fareed, J. W. Yang, Grigory Simin, M. Asif Khan, R. Gaska, M. Shur, C. Rojo, L. Schowalter

Faculty Publications

Temperature-dependentphotoluminescence(PL)measurements were performed for A-plane and C-plane bulk AlN single crystals and epitaxial layers on sapphire. A strong near-band-edge (NBE) emission and deep-level luminescence were observed. At low excitations, the emission spectra are dominated by free and bound excitonic transitions and their LO-phonon replicas. At high excitations, the broadening and redshift of the NBE band is attributed to dense electron–hole plasma formation. The PL spectra differences of bulk single crystals and epilayers is explained by the electron–hole plasma expansion peculiarities.

Self-Assembled Networks With Neural Computing Attributes, Supriyo Bandyopadhyay, L. Menon, N. Kouklin, P. F. Williams, Natale J. Ianno

P. F. (Paul Frazer) Williams Publications

Two-dimensional arrays of vertical quantum wire Esaki tunnel diodes, laterally connected to their nearest neighbors by resistive/capacitive connections, constitute a powerful and versatile neuromorphic architecture that can function as classical Boolean logic circuits, associative memory, image processors, and combinatorial optimizers. In this paper, we discuss the basic philosophy behind adopting this architecture for nanoelectronic circuits and report on our experimental progress towards synthesizing this system.

An Algorithm Applicable To Clearing Combinatorial Exchanges, Marius Silaghi

Electrical Engineering and Computer Science Faculty Publications

It is important to approach negotiations in a way that ensures privacy. So far, research has focused on securely solving restricted classes of negotiation techniques, mainly the (M+1)-st-price auctions. Here we show how these results can be adapted to more general problems. This paper extends our previous results on how distributed finite discrete problems can be solved securely. Such problems can model larger classes of negotiation problems, .e.g. Combinatorial Exchanges [Sil02]. In Finite Discrete Maximization, each tuple in the problem space is associated with an integer value in a predefined interval and we search for a maximizing input. Values from …

Performance Analysis Of A Maximum-Likelihood Speckle Motion Estimator, Donald D. Duncan, Sean J. Kirkpatrick

Electrical and Computer Engineering Faculty Publications and Presentations

Presented herein is a performance analysis of a maximum likelihood estimator for calculating small speckle motions. Such estimators are important in a variety of speckle techniques used in non-destructive evaluation. The analysis characterizes the performance (bias and RMS deviation) of the estimator as a function of the signal-to-noise ratio. This SNR parameter is a convenient surrogate for decorrelation of sequential speckle patterns such as are seen in biological tissues. Although the particular estimator is predicated on speckle motions that are a small fraction of a pixel, accurate performance is demonstrated for instantaneous motions of up to ±0.8 pixel/record. Beyond this …

Network Traffic Anomaly Detection Based On Packet Bytes, Philip K. Chan, Matthew V. Mahoney

Electrical Engineering and Computer Science Faculty Publications

Hostile network traffic is often "different" from benign traffic in ways that can be distinguished without knowing the nature of the attack. We describe a two-stage anomaly detection system for identifying suspicious traffic. First, we filter traffic to pass only the packets of most interest, e.g., the first few packets of incoming server requests. Second, we model the most common protocols (IP, TCP, telnet, FTP, SMTP, HTTP) at the packet byte level to flag events (byte values) that have not been observed for a long time. This simple system detects 132 of 185 attacks in the 1999 DARPA IDS evaluation …

Shared-Data Or Message Passing Computing Models – A Human Factor In Technical Choices, Angela Sodan, Luiz Fernando Capretz

Electrical and Computer Engineering Publications

No abstract provided.

Modeling, Fabrication, And Optimization Of Niobium Cavities: Phase Ii Quarterly Report, Robert A. Schill Jr., Mohamed Trabia

Transmutation Sciences Materials (TRP)

Multipacting is one of the major loss mechanisms in rf superconductivity cavities for accelerators. This loss mechanism limits the maximum amount of energy/power supported by the cavities. Optimal designs have been identified in others’ studies. In practice, these designs are not easily manufactured. Chemical etching processes used to polish the cavity walls result in a nonuniform surface etch. A nonuniform surface etch will leave some unclean areas with contaminants and micron size particles. These significantly affect mutipacting. Further, a nonuniform etch will leave areas with damaged grain structure, which is not good for superconducting properties. Typically, the depth of chemical …

Comparison Of Open- And Closed-Loop Process Identification Techniques In The Time-Domain, Tony Kealy, Aidan O'Dwyer

Conference papers

Abstract: This paper describes seven methods to identify a mathematical model for a real process with a time delay. The process is the Process Trainer, PT326 from Feedback Instruments Limited. Six of the methods use the step response data and one of the methods uses the impulse response data for identification.