Engineering Commons^™

Steel Sheet Sheathing Options For Cfs Framed Shear Wall Assemblies Providing Shear Resistance, Cheng Yu, Hitesh Vora, Tony Dainard, Jimmy Tucker, Pradeep Veetvkuri

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

The North American Standard for Cold-Formed Steel Framing - Lateral Design, AISI S213-07, provides design provisions for cold-formed steel framed shear walls with steel sheet sheathing. However, options are limited to 18-mil and 27-mil steel sheet sheathing. Presented in this report are the findings from an extensive monotonic and cyclic testing program conducted at the University of North Texas of 30-mil and 33-mil steel sheet sheathed shear walls with 2:1 and 4:1 aspect ratios and 27-mil sheet steel shear walls with 2:1 aspect ratio and 6-in., 4-in., 3-in., and 2-in. fastener spacing at panel edges. It is anticipated that the …

Cold-Formed Steel Framing Design Guide, Second Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

This Design Guide has been developed under the direction of the American Iron and Steel Institute Committee on Specifications for the Design of Cold-Formed Steel Structural Members. The development of the Guide was sponsored by the American Iron and Steel Institute and the Steel Stud Manufacturers Association. The AISI Committee on Specifications wishes to acknowledge and express gratitude to Mr. Thomas Trestain of T. W. J. Trestain Structural Engineering who was the author of this Guide.

With anticipated improvements in understanding of the behavior of cold-formed steel and the continuing development of new technology, this material might become dated. It …

North American Standard For Cold-Formed Steel Framing -- Wall Stud Design, 2007 Edition (Reaffirmed 2012), American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

North American Standard For Cold-Formed Steel Framing -- Floor And Roof System Design, 2007 Edition (Reaffirmed 2012), American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Steel Sheet Sheathing Options For Cfs Framed Shear Wall Aseemblies Providing Shear Resistance, Cheng Yu, Hitesh Vora, Tony Dainard, Pradeep Veetvkuri

CCFSS Library (1939 - present)

In cold-formed steel construction, stud walls covered with steel sheet sheathing is an available option to resist lateral loads such as those caused by wind and earthquakes. The current American Iron and Steel Institute (AISI) Standard for Cold-Formed Steel Framing - Lateral Design 2004 Edition provides nominal shear strength for a limited range of steel sheet sheathed shear wall configurations. This report presents a research project developed to add values for 0.030-in. and 0.033-in. steel sheet sheathed shear walls with 2:1 and 4:1 aspect ratios and 0.027-in. sheet steel shear walls with 2:1 aspect ratio and 6-in., 4-in., 3-in., and …

Assessment Of The Bill Emerson Memorial Cable-Stayed Bridge Based On Seismic Instrumentation Data, Genda Chen, Dongming Yan, Wenjian Wang, Man Zheng, Louis Ge, Frank Liu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this study, both ambient and earthquake data measured from the Bill Emerson Memorial Cable-stayed Bridge are reported and analyzed. Based on the seismic instrumentation data, the vibration characteristics of the bridge are investigated and used to validate a three-dimensional Finite Element (3-D FE) model of the bridge structure. The 3-D model is rigorous and comprehensive, representing realistic dynamic behaviors of the bridge. It takes into account the geometric nonlinear properties caused by cable sagging and soil-foundation-structure interaction in the Illinois approach of the bridge. The FE model is successfully verified and validated by using the natural frequencies and mode …

Ccfss Technical Bulletin Fall 2007, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Technical Bulletins (1993 - 2020)

No abstract provided.

Ccfss News Fall 2007, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Newsletters (1999 - 2008)

No abstract provided.

North American Specification For The Design Of Cold-Formed Steel Structural Members, 2007 Edition, American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Experiments On Rotational Restraint Of Sheathing, Benjamin W. Schafer

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

North American Standard For Cold-Formed Steel Framing -- Header Design, 2007 Edition (Reaffirmed 2012), American Iron And Steel Institute

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Durability Performance Of Polyurea Confined Concrete Cylinders, Matthew Beyer

Opportunities for Undergraduate Research Experience Program (OURE)

No abstract provided.

Analysis Of Vertical Takeoff And Landing (Vtol) Unmanned Aerial Vehicles (Ua V) With Emphasis On Tilt Duct And Tilt Rotor Systems, Devin Boyle

Opportunities for Undergraduate Research Experience Program (OURE)

No abstract provided.

The Use Of Thermoelectric Peltiers To Recapture Waste Heat, Navarre Bartz

Opportunities for Undergraduate Research Experience Program (OURE)

Peltier devices are a method of converting differences in temperature into electrical energy. Using data from a supplier of these devices, calculations were made to determine the efficiency of these devices in conjunction with a residential solar hybrid electric system. The initial calculations show efficiencies less than 2% with the temperature differences experienced during the springtime. While this efficiency doesn't sound stellar, taking into account the current efficiency of residential solar cells, this would be an appreciable addition to the power output of a residential solar system.

Additional Shear Wall Values For Light Weight Steel Framing, Reynaud Serrette, Jose Encalada, Georgi Hall, Brandon Matchen, Hoang Nguygen, Alexander Williams

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

This report presents the results of 16 monotonic and 28 cyclic tests of flat strap X-braced walls, steel sheathed shear walls, high aspect ratio shear walls and shear walls framed with 54-mil and 43-mil studs. The findings provided a basis for continued research and development efforts, leading to the establishment of provisions for cold-formed steel-framed diagonal strap braced walls and Type I shear walls.

Damage Detection In Ambient Vibration Using Proportional Flexibility Matrix With Incomplete Measured Dofs, Zhongdong Duan, Guirong Yan, Jinping Ou, Billie F. Spencer

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Structural Damage Detections based on the Changes of Dynamic Properties Are a Major Concern Tor Structural Health Monitoring. in This Paper. Efforts Are Made to Extend the Flexibility-Based Damage Localization Methods, Especially the Damage Locating Vector (DLV) Method, to the Case of Ambient Vibration with Incomplete Measured Degree of Freedom, Where Flexibility Matrices Are Not Available. First, the Method to Assemble a Proportional Flexibility Matrix (PFM) with Arbitrarily Scaled Modal Shapes of Full Measured Degrees of Freedom (DOF) is Introduced. the PFM is within a Scalar Multiplier to the Real Flexibility Matrix, and the Multiplier is Shown to Be the …

Ccfss Technical Bulletin Spring 2007, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Technical Bulletins (1993 - 2020)

No abstract provided.

Ccfss News Spring 2007, Wei-Wen Yu Center For Cold-Formed Steel Structures

CCFSS Newsletters (1999 - 2008)

No abstract provided.

Performance Of Steel Products Coated With Zinc And Zinc Alloys In Pressure Treated Wood, Nahb Research Center, Inc.

American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)

No abstract provided.

Performance Evaluation Of Existing Analytical Methods To Compute The Shear Contribution Provided By Externally Bonded Frp Sheets In Concrete Structures, Rocio Patricia Tumialan

Masters Theses

"External application of FRP composites has been adopted for strengthening and/or repair of concrete structures in many applications during the last two decades. However, the research into shear strengthening using FRP composites has not been widely conducted as compared to flexural strengthening and axial load capacity increase, and the results obtained thus far are scarce and sometimes controversial. This study presents a review of analytical studies and design guidelines on shear strengthening of concrete structures with externally-bonded FRP laminates, and their assessment with experimental data collected from the literature. The strengths and weaknesses of each model and design guidelines/codes/specifications are …

Steel Deck Institute Design Manual For Composite Decks, Form Decks, And Roof Decks, Steel Deck Institute

Steel Deck Institute (SDI) Specifications and Manuals (1939 - present)

No abstract provided.

Towards Better Utilization Of Nexrad Data In Hydrology: An Overview Of Hydro-Nexrad, Witold F. Krajewski, Anton Kruger, Ramon Lawrence, James A. Smith, A. Allen Bradley, Matthias Steiner, Mary Lynn Baeck, Mohan K. Ramamurthy, Jeffrey Weber, Stephen A. Delgreco, Bong Chul Seo, Piotr Domaszczynski, Charles Gunyon, Radoslaw Goska

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

With a very modest investment in computer hardware and the open-source local data manger (LDM) software from UCAR's Unidata Program Center, an individual researcher can receive a variety of NEXRAD Level III gridded rainfall products, and the unprocessed Level II data in real-time from most NEXRAD radars. Additionally, the National Climatic Data Center has vast archives of these products and Level II data. Still, significant obstacles remain in order to unlock the full potential of the data. One set of obstacles is related to effective management of multi-terabyte data sets: storing, compressing, and backing up. A second set of obstacles, …

Hydro-Nexrad Radar-Rainfall Estimation Algorithm Development, Testing And Evaluation, Witold F. Krajewski, Bong Chul Seo, Anton Kruger, Piotr Domaszczynski, Gabriele Villarini, Charles Gunyon

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Hydro-NEXRAD radar-rainfall estimation algorithms involve three main components: 1) preprocessing, 2) rain rate, and 3) rainfall accumulation. The preprocessing algorithm performs the quality control of reflectivity volume data and generates a hybrid scan. That is, reflectivity values for each azimuth and range bin are assigned from the several lowest elevation angles. It optionally estimates an azimuth-dependent vertical reflectivity profile and performs a correction for range effects. The rain rate algorithm converts the corrected reflectivity to rainfall intensity. The user can specify any power-law type empirical relationship between reflectivity and rainfall intensity. The last step of rainfall estimation is to …

Evaluation Of Time Independent Rheological Models Applicable To Fresh Self-Compacting Concrete, Dimitri Feys, Ronny Verhoeven, Geert De Schutter

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Self-Compacting Concrete is a New Type of Concrete Which is More Liquid Compared to Traditional Concrete and Which Does Not Need Any Form of External Compaction. as a Result, This Type of Concrete is Suitable for a New Placing Technique: Pumping SCC from the Bottom in the Formwork and Letting It Rise in the Formwork Due to the Applied Pressure. in Order to Understand the Phenomena Occurring during Pumping Operations, the Rheological Properties of SCC Must Be Investigated and Controlled. Tests Have Been Performed with Two Different Rheometers, Which Are Described in This Paper. for the Tattersall MIk-II Rheometer, a …

Visual Traffic Movement Counts At Intersection For Origin-Destination (O-D) Trip Table Estimation, S. Lee, Hojong Baik, J. Park

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Origin-destination (O-D) trip table is necessary information for transportation planning and traffic impact study. However, current O-D estimations rely on estimated directional traffic counts at intersections, which obviously diminish reliability in the table. A video-based vehicle tracking system that utilizes wide view-angle lenses has been studied [26] to provide accurate direction traffic counts. The system expands the area covered by a single camera and uses a particle filtering method to handle environmental changes as well as geometric distortion caused by those lenses. This paper shows tracking capability of the system and also shows how to incorporate the directional traffic counts …

Innovative Solutions In Bridge Construction, Rehabilitation, And Structural Health Monitoring, Fabio Matta

Doctoral Dissertations

"This dissertation includes three technical papers that investigate the development of innovative technologies for bridge construction, rehabilitation, and structural health monitoring, respectively, at different stages of the technology transfer process...The research impact is twofold: first is the introduction of promising innovative technologies in development and implementation projects with the direct involvement of forward-thinking industry partners; second is the demonstration of the validity of these technologies on the basis of a rigorous scientific approach"--Abstract, page iv.

Análisis De Deslizamientos En La Ciudad Capital Utilizando Sistemas De Información Geográfica, Pedro Pablo Conlledo, Ronaldo Luna

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

En Guatemala, los daños ocasionados por deslizamientos de tierra son innumerables, y sin embargos son pocos los esfuezos que se han hecho a nivel nacional por estudiarlos. El principal objetivo de este trabajo fue utilizar Sistemas de lnformacion Geografica (SlG) para estudiar sistematicamente la ocurrencia de deslizamientos en el Departamento de Guatemala con la informacion disponible.

Experimental And Analytical Evaluation Of Frp-Confined Large Size Reinforced Concrete Columns, Silvia Rocca

Doctoral Dissertations

"Fiber Reinforced Polymer (FRP) jacketing of Reinforced Concrete (RC) columns, as a rapidly growing strengthening technique, requires appropriate design methods. However, the current available design guides are based on models, in their majority semi-empirical, and calibrated with small-scale plain concrete specimens. These models might not be reliable in predicting the strength and ductility enhancement sought through FRP-confinement in RC columns with geometric and material properties as found in practice. This dissertation presents the research conducted in three technical papers. In the first paper, the performance of 22 FRP-wrapped RC columns of medium- and large-scale is studied. The results of the …

Field And Laboratory Investigation Of Ozone-Indoor Surface Reactions: Secondary Emissions Inventory And Implications For Indoor Air Quality, Hong Wang

Doctoral Dissertations

"Interfacial chemistry greatly influences human exposure to reactants and products in indoor environments. Emissions of volatile organic compounds, as a result of ozone-surface interactions, can lower an occupant's exposure to ozone, but increase indoor concentrations of odorous and carcinogenic compounds. Therefore, investigation of ozone-surface interactions are necessary for better understanding and controlling exposure to ozone and the products of indoor surface chemistry. In this dissertation, field experiments were conducted in five homes in three seasons to quantify ozone-initiated secondary emission rates (SERs), yields surface reaction probabilities and study their temporal trends"--Abstract, page iv.

The Leaching Behavior Of Arsenic, Selenium And Other Trace Elements In Coal Fly Ash, Tian Wang

Doctoral Dissertations

"The goals of this study are four fold, they are: (1) to investigate the leaching behavior of arsenic and selenium from fly ash as well as their affecting factors; (2) to analyze the speciation of arsenic and selenium in fly ash leachate; (3) to develop a modeling approach to quantify the availability and stability of trace cationic elements in fly ash; (4) to apply this model to describe the leaching/adsorption behavior of arsenic and selenium on fly ash, as well as the calcium effect on arsenic (V) adsorption process"--Abstract, page iv.