Engineering Commons^™

Investigation Of Surface Charge Using Faraday Bucket Measurements: Analysis On Electrospun Polyvinylidene Fluoride Fiber Mats, Ryan Kantenwein

Williams Honors College, Honors Research Projects

Piezoelectric polymer materials such as polyvinylidene fluoride exhibit beneficial properties for use in personal protective equipment (PPE) against viral contaminants and other foreign microparticles. The electrospinning process of this material allows for surface charge to develop over a controlled surface area. Kynar 761 at 10 wt% demonstrates increased surface charge after withstanding a flow of aerated NaCl particles from a TSI 8130 instrument. Utilizing voltage measurements from a Faraday bucket, 18 wt% Kynar 761 and MG-15 exhibit surface charge when undergoing an electrospinning process; however, Kynar MG-15 displays lower charge values than that of Kynar 761. Several critical factors such …

Methods For Film Coating Electrospun Fibers, Kristopher Dejean

Williams Honors College, Honors Research Projects

Electrospinning uses high voltages to form polymer nanofiber membranes. These membranes have potential for use in filtration, tissue engineering, drug delivery, and catalysis. The nonwoven fiber mat is malleable but has a low tensile strength compared to a solid film of the same polymer. Joining the fibers with a thin film is desired to balance the strength and flexibility. Three methods of producing a film on fiber membrane were tested. The techniques are spraying then melting, spin coating, and dip coating. Electrospinning setup conditions, solvent ratios, damage to fibers, and spin coating speeds were determined. Research was abruptly stopped and …

A Comparison Of Fiber Mat Thickness Measurement Techniques Using Laser Interferometry And Water Displacement, Ryan Seabeck

Williams Honors College, Honors Research Projects

Polymer fiber mats may often be very thin which leads to complications in measuring thickness. The thickness of fiber mats, however, is crucial in understanding their behavior. Thickness affects how well the mat works as a filter as well as the pressure drop across the mat, and herein lies the need for accurate measurement techniques. Currently two of the available techniques for measuring mat thickness are by laser interferometry[1] and by buoyancy force when submerged in water[2]. Instead of measuring the buoyancy force in this experiment, an enclosure intended to measure the thickness via water displacement was …

Filtration Apparatus Design For Oil-Water Separation Using Membranes And Sponges, Alec Jerger

Williams Honors College, Honors Research Projects

It can be difficult to separate water and oil emulsions through traditional filtration. Therefore, investigations of filtering using thermo-responsive (TR) polymers, in this case poly(vinyl methyl ether) (PVME), was conducted. It’s hypothesized that below its lower critical solution temperature (LCST), PVME has an affinity for water while oil substances do not. Above the LCST the opposite will be true. To verify this hypothesis, iterations of filtration designs were created to provide optimum control over the parameters to measure flow. The final optimized experimental apparatus was a Chromaflex glass column which was air tight and controlled all parameters besides fluid flow. …

Prevention Of Harmful Algal Blooms By The Mitigation Of Phosphorus Nutrient Loading Via Filtration By Steel Wool And Activated Carbon, Ronald Simpson, Sara Kidd, Samantha Zidd

Williams Honors College, Honors Research Projects

Harmful Algal Blooms (HABs) are a devastating ecological and economic consequence of the abundance of nutrient-rich agricultural runoff entering aquatic ecosystems (Baker et al. 2014). Bio-available phosphorus from synthetic fertilizers is one of the major nutrients contributing to this global issue. Previous studies indicated that dissolved phosphorus can be removed from an aqueous environment when passed through a composite mixture of granular steel wool particles and activated carbon (Erickson, Gulliver, and Weiss, 2007). In this project, we conducted experiments using higher quality concentration measurements to determine what grades of steel wool (SW-0000, SW-000, SW-00) and types of activated carbon (granulated …

Separation Of Water From Ulsd Using Superhydrophobic Ps Nanofiber Mats, Alisa G. Webel

Williams Honors College, Honors Research Projects

Superhydrophobic polystyrene nanofiber membranes have potential to separate micron scale water droplets from organic due to their hydrophobicity and small pore openings. Polystyrene nanofibers were electrospun into flat sheets and cylindrical filter membranes. The fibers were crosslinked to increase strength and reduce solubility in diesel fuel. The filters were tested and the filtration efficiency was compared to their non-crosslinked counterparts. The optimal electrospinning conditions to create superhydrophobic nanofibers were found to be 20 wt. % PS fibers at 1 mL/hr. under a current of 20kV and at a distance of 20 cm away from the ground. It was found that …

Electrospinning Of S-B-S Triblock And S-I-S Triblock Copolymers For Use In Fuel Filtration, Kevin Houser

Williams Honors College, Honors Research Projects

The following research project looked into the potential of using nanofibers of syrene-isoprene-styrene triblock copolymer produced through the electrospinning process for the filtration of water out of fuel as well as a comparison of styrene-isoprene-styrene triblock to the styrene-butadiene-styrene triblock nanofibers produced at equivalent operating parameters. Based on the work completed, it is concluded that the styrene-isoprene-styrene triblock is not suitable for use in filtration with the current electrospinning conditions. On average, the styrene-isoprene-styrene triblock produced nanofibers of lower average diameter and lower standard deviation in diameter when compared to styene-butadiene-styrene triblock.

Filtration Of Aerosolized Oils With Layered Filter Media And Drainage Channels, Corey A. Boldon

Williams Honors College, Honors Research Projects

The purpose of this experiment is to compare the efficiency of four different filter media with two different drainage channel materials when filtering out aerosolized oil. The filter media include 2 micron stainless steel fibers, 6.5 micron stainless steel fibers, 2 micron woven glass fibers, and 6 micron woven glass fibers. The drainage channel materials are 500 micron Teflon (PTFE) and nylon mesh.

One major application that this research is targeted towards is air compressors. Air compressors use lubricating oil to minimize wear and corrosion. During operation some of this lubricating oil is aerosolized into the outgoing air stream. Inhalation …