Engineering Commons^™

Investigation Of Foam Based Photobioreactor For The Cultivation Of Chlorella Vulgaris Cpcc 90, Anuradha Krishnan

Electronic Thesis and Dissertation Repository

Today, microalgae are cultured in large-scale systems such as open ponds and photobioreactors. Open pond systems, while not expensive, have disadvantages, including contamination and high water consumption, resulting in increased cost of harvesting and quick evaporation. Photobioreactors overcome some of the challenges of an open pond system. However, the reactor setup, operation, and microalgae harvesting are relatively more expensive when compared to conventional techniques. In this study, a novel foam-based photobioreactor system was applied to investigate both the cultivation and harvest of microalgae using different surfactant agents, i.e., rhamnolipids, Bovine Serum Albumin (BSA), saponin, and the commercial surfactant Pluronic f127 …

Experimental And Simulation Study Of Reactive Silver Ink Droplet Evaporation, Weipeng Zhang

Electronic Thesis and Dissertation Repository

The evaporation of particle-free silver ink droplets on heated substrates directly impacts the morphology of the resultant silver particles and films. In this thesis, COMSOL Multiphysics simulations of the solvent (water-ethylene glycol mixture) droplet evaporation process are used to explain the microflows, mass transfers, and heat distribution responsible for the experimental observations. The reactive ink incorporates fluoro-surfactant FS-31 and poly (acrylamide) (PAM) to suppress the coffee-ring effect that negatively impacts the electrical conductivity. Experiments show that the droplet evaporation process results in varied silver particle morphology, depending on the locations within the droplet, leading to uneven surfaces. Large particles (3 …

Conversion Of Biomass Derived Tar In A Catalytic Post-Gasification Process, Floria Rojas Chaves

Electronic Thesis and Dissertation Repository

The present MESc thesis reports the performance of a fluidizable CeO₂ promoted Ni/γ-Al₂O₃ catalyst to be used in a post-gasification process for tar removal. The catalysts developed were prepared using the incipient wetness technique and characterized chemically and physically, using the following techniques: N₂ Adsorption-Desorption, XRD, NH₃ and CO₂ TPD, Pyridine-FTIR, H₂-TPR, and H₂-Pulse Chemisorption. The catalysts were tested in a fluidized CREC Riser Simulator, in the 500°C-550°C temperature range, within 5 s-10 s reaction times, using both steam and steam-H₂/CO₂ atmospheres.A 2-methoxy-4-methlyphenol (2M4MP) compound was …

Application Of Crystal Engineering In Multicomponent Pharmaceutical Crystals: A Study Of Theory And Practice, Soroush Ahmadi Nasrabadi

Electronic Thesis and Dissertation Repository

Multicomponent crystallization, a prominent strategy in crystal engineering, offers the ability to modify the physicochemical properties of crystals by introducing a secondary component to their lattice structure. Such multicomponent crystals have found widespread application in the pharmaceutical industry. This thesis explores the experimental screening, characterization, application, and theoretical prediction of multicomponent crystals of Active Pharmaceutical Ingredients (APIs).

The first case study investigates a new solvate of Dasatinib which exhibits high instability at room temperature and transforms into a different polymorph upon desolvation. The crystal structure of this compound is obtained, revealing insights into its transient nature and the potential application …

Catalytic Consequences Of Catalyst Pellet Architecture On The Methanol To Oxymethylene Process, Sebastian M K Cook

Electronic Thesis and Dissertation Repository

A critical step for the synthesis of renewable oxy methyl ethers (OME) targeted towards diesel substitution, is the catalytic production of a dimethoxymethane/formaldehyde mixture from methanol and air. The bifunctional catalyst requirements needed for methanol to undergo both the acidic and oxidative steps required for dimethoxymethane formation have been recently established for TiO₂-supported vanadia catalysts. However, translating these requirements to a catalyst capable of industrial operation remains a challenge. This thesis examines the considerations and adjustments needed to translate the molecular active phase to a large-scale catalytic pellet, including active phase distribution and possibility of hot-spot creation during …

Hydrothermal Liquefaction (Htl) Of Lignocellulosic Biomass For Biocrude Production: Reaction Kinetics And Corrosion-Resistance Performance Of Candidate Alloys For Reactors, Haoyu Wang

Electronic Thesis and Dissertation Repository

In recent years, the rapid increase in the demand for clean energy and green chemicals as well as concerns over the supply and environmental impacts associated with fossil. resources have stimulated intensive research on conversion of bioresources, such as lignocellulosic biomass and biowaste, into energy, fuels, chemicals, and materials.

Hydrothermal liquefaction (HTL) is a unique thermochemical conversion process, particularly applicable for the conversion of wet biomass and biowaste feedstocks. Most of the biomass HTL studies are conducted in batch reactor and focus on the effects of catalysts, reaction temperature and time on production efficiency and chemical properties of the products. …

Investigation Of Heavy Metal Removal From Synthetic Desalter Effluent Using A Two-Step Approach By Micellar-Enhanced Ultrafiltration And Microbial Fuel Cell, Carlos Munoz-Cupa

Electronic Thesis and Dissertation Repository

Heavy metals in wastewater streams negatively affect the environment due to their high toxicity. Non-conventional heavy metal removal methods show higher efficiencies for the remediation of these pollutants. In this investigation, a two-step approach using micellar-enhanced ultrafiltration (MEUF) and microbial fuel cell (MFC) was investigated to remove copper, manganese, and zinc from a synthetic salt wastewater containing magnesium, sodium, and phenol. This synthetic solution was used to simulate refinery wastewater streams such as desalter effluent. The study was carried out in three phases. In the first phase, a flat plate polyether sulfone membrane was investigated for the MEUF process with …

Value Added Products From Nonconventional Agricultural Biomass Waste Through Thermochemical Transformation, Nicolas A. Sarmiento

Electronic Thesis and Dissertation Repository

The alteration of temperature patterns around the world has become noticeable in the recent decade. Sea level rise, wildfires, and high temperatures have made people realize that climate change is affecting humans more tangibly than ever. Therefore, the United Nations have pushed to make policies to mitigate this problematic situation. This research investigated the production of biochar from agricultural waste through pyrolysis for fighting climate change and adding value to waste. Experiments in a laboratory scale reactor were conducted to obtain yields of pyrolytic products. Then, analysis of products provided data for characterization and the LCA of the tomato plant …

Effect Of Process Parameters On The Mechanical Properties Of Carbon Fiber Epoxy Composites By Wet Compression Molding, Saboora Ayatollahi

Electronic Thesis and Dissertation Repository

In recent years, due to growing environmental concerns, composite materials have emerged as a promising lightweight alternative for metals in structural applications in automobiles. Among composite manufacturing processes, Wet Compression Molding (WCM) is a new method of producing Carbon Fiber Reinforced Polymer (CFRP) components. For similar processes like RTM, operating conditions are always one of the factors that impact the mechanical performance of CFRP parts. Thus, this thesis aimed to investigate the effects of operating conditions, including resin temperature, mold temperature, resin set time, gap closure speed, and mold curing time on the mechanical property of the composite parts. In …

Modeling And Multi-Objective Optimization Of Wastewater Treatment Process, Navneet Kaur

Electronic Thesis and Dissertation Repository

Wastewater is water that has already been used and requires treatment before releasing it into natural water bodies like lakes and rivers. Wastewater treatment is the process of removing impurities from wastewater. In this treatment process, the impurities are removed and converted to effluent. This effluent is returned to the water cycle with minimum impact on the environment. Conventional treatment plants consist of three stages: primary, secondary, and tertiary treatment. Treatment of wastewater is quite complicated because of the number of stages involved in this process. Most wastewater treatment plants are operated manually therefore at times it becomes difficult for …