Engineering Commons^™

A Digital One Degree Of Freedom Model Of An Electromagnetic Position Sensor, Michelle Elizabeth Weinmann

Mechanical & Aerospace Engineering Theses & Dissertations

The purpose of this project was to improve an existing system currently in use by NASA Langley Research Center (LaRC). The 6-inch Magnetic Suspension and Balance System (MSBS) built at MIT is operational with control in three degrees of freedom, with two additional degrees of freedom exhibiting passive stability. The means for measuring model displacement within the magnetic environment is an Electromagnetic Position Sensor (EPS), consisting of excitation coils at 20 kHz and multiple sets of pickup coils. The pickup coil voltages are proportional to model displacement in each degree of freedom. However, the EPS electronic signal processing system is …

Low-Cost Skewed Redundant Imu Configuration For State-Space Recovery In A Saturated Environment, Levi S. Hubbard

Graduate Theses, Dissertations, and Problem Reports

Low-cost sensors for state space determination can be used successfully for ground vehicles, robots, unmanned aerial vehicles, and Internet-of-Things applications. When a high fidelity Inertial Measurement Unit (IMU) cannot be obtained for state space determination, low-cost sensors can be used to satisfactory standards, despite their limitations in capabilities, by using various implementation techniques. The research group was experimentally investigating state space information of an unstable flying vehicle for motion simulation validation. The high fidelity motion capture system would intermittently lose track of the flight vehicle which lost critical flight data.

The goal was to determine the potential of low-cost off-the-shelf …

Accumulator Volume Sensor Final Project Report, Chris Naughton, Kinwei Yu, Michael George

Mechanical Engineering

Accumulator Volume Sensing Team has developed two sensor designs aimed at detecting the position of the piston within a 4024 accumulator. The two designs include the use of a Renishaw LMA10 magnetic encoder and a SpectraSymbol HotPot linear potentiometer. The magnetic encoder solution drastically increases the accuracy of sensing the piston position compared to the current solutions of both a string-pot and linear variable differential transformer while costing slightly less. The linear potentiometer seeks to provide a solution that drastically decreases the cost compared to the present sensing methods. Both designs call for a modification to one half of the …

Low-Cost Imu Implementation Via Sensor Fusion Algorithms In The Arduino Environment, Brandon Mccarron

Aerospace Engineering

A multi-phase experiment was conducted at Cal Poly in San Luis Obispo, CA, to design a low-cost inertial measurement unit composed of a 3-axis accelerometer and 3-axis gyroscope. Utilizing the growing microprocessor software environment, a 3-axis accelerometer and 3-axis gyroscope simulated 6 degrees of freedom orientation sensing through sensor fusion. By analyzing a simple complimentary filter and a more complex Kalman filter, the outputs of each sensor were combined and took advantage of the benefits of both sensors to improved results. Gyroscopic drift was removed in the pitch and roll axes using the Kalman filter for both static and dynamic …

A Resistance Based Structural Health Monitoring System For Composite Structure Applications, Dennis N. Boettcher

Master's Theses

This research effort explored the possibility of using interwoven conductive and nonconductive fibers in a composite laminate for structural health monitoring (SHM). Traditional SHM systems utilize fiber optics, piezoelectrics, or detect defects by nondestructive test methods by use of sonar graphs or x-rays. However, these approaches are often expensive, time consuming and complicated.

The primary objective of this research was to apply a resistance based method of structural health monitoring to a composite structure to determine structural integrity and presence of defects.

The conductive properties of fiber such as carbon, copper, or constantan - a copper-nickel alloy - can be …

Aircraft Longitudinal Control Experiment, Dustin Schaff

Aerospace Engineering

This paper describes the design, fabrication, and analysis of an experiment that demonstrates the stability and control system characteristics of an aircraft constrained at the center of gravity in an air flow field. Given a set of basic requirements, the physical system (including the airframe, wings, tail, and mounted ball bearing) was designed, modeled, and manufactured. With the aircraft placed in front of a fan and allowed to rotate freely with the ball bearing, an angular rate sensor and servo motor to the deflect the elevator may be connected to any computer using an analog/digital Data Acquisition (DAQ) device to …