Engineering Commons^™

Development Of Load Measurement Technique For Arbitrary Shapes, Quintin J. Cockrell

Master's Theses

Obtaining aerodynamic forces and moments about all three orthogonal axes for arbitrary shapes at arbitrary orientations in a fast manner via a measurement technique specific to Cal Poly’s low-speed wind tunnel to continually obtain the forces and moments under quasi-steady conditions is explored. A Continuous Rotation Technique (CR) uses a 6-DOF load cell and stepper motor to rotate an object about an axis for a complete rotation. The forces and moments acting upon the object pass through the stepper motor and interface plates and recorded by the load cell as the object is rotated continuously a finite number of rotations. …

Parametric Optimization Of A Wing-Fuselage System Using A Vorticity-Based Panel Solver, Chino Cruz

Master's Theses

Aerodynamic topology optimization is a useful tool in the aerodynamic design pro-
cess, especially when looking for marginal gains within a design. One example is
a turboprop racer concept aircraft that is designed with the goal of breaking world
speed records. An optimization framework was developed with the intention of later
being applied to this design. In the early design stages, the optimization framework
must focus on quicker methods of drag estimation, such as a panel codes. The large
number of design variables in topology optimization can exponentially increase func-
tion evaluations and thus computational cost. A vorticity-based panel solver …

Coupled Boundary Conditions For Modeling Airbreathing Engines, Adam Louis Waldemarson

Master's Theses

Modeling the flight conditions of an aircraft that utilizes an airbreathing propulsion system necessitates a method to account for the increase in energy introduced into the flow. Current methods for modeling engines either assign fixed conditions on flat faces on the intake and exhaust through a manual process with the use of external models or attempt to model the flow through the engine within the simulation using complex and computationally expensive geometry and solvers. The method presented attempts to provide an intermediate option to model airbreathing engines through coupling the intake and exhaust boundary conditions with a parametric engine model. …

Structural Loads And Preliminary Structural Design For A World Speed Record-Breaking Turbo-Prop Racing Airplane, Matthew G. Slymen

Master's Theses

The Cal Poly SLO Turbo-Prop Racer project aims to design a world speed record-breaking aircraft, capable of flying more than 550 miles per hour on a 3-kilometer closed course. To further this endeavor, this thesis presents the calculations of load distributions across the aircraft’s wing and tail and preliminary structural estimates of primary structural components for verification of the loads calculations and for use in a future finite element model. The aircraft’s fundamental design characteristics effect on the structure of the aircraft, namely the unique Y-tail design, are first examined. Then, loads are calculated in accordance with the regulation dictated …

Aeroelastic Analysis Of Small-Scale Aircraft, Kent Roberts

Master's Theses

The structural design of flight vehicles is a balancing act between maximizing loading capability while minimizing weight. An engineer must consider not only the classical static structural yielding failure of a vehicle, but a variety of ways in which structural deformations can in turn, affect the loading conditions driving those deformations. Lift redistribution, divergence, and flutter are exactly such dynamic aeroelastic phenomena that must be properly characterized during the design of a vehicle; to do otherwise is to risk catastrophe. Relevant within the university context is the design of small-scale aircraft for student projects and of particular consideration, the DBF …

Characterization, Design, And Optimization Of Dual-Purpose Wind Turbines And Frost Protection Fans, Ethan Narad

Master's Theses

This thesis report outlines the creation of a MATLAB tool to design reversible machines that can function as both wind turbines and as agricultural frost protection fans. Frost protection fans are used to prevent crop loss during radiative freeze events during which a temperature inversion is present. Such a dual-purpose machine fundamentally has the constraint that it must use symmetric airfoils, so a suite of tools for automatically designing an optimized wind turbine blade with symmetric airfoils using the Blade Element Momentum (BEM) theory approach is presented. The BEM code is then re-derived and adapted for use with a frost …

Integral Boundary Layer Methods In Python, Malachi Joseph Edland

Master's Theses

This thesis presents a modern approach to two Integral Boundary Layer methods implemented in the Python programming language. This work is based on two 2D boundary layer methods: Thwaites' method for laminar boundary layer flows and Head's method for turbulent boundary layer flows. Several novel enhancements improve the quality and usability of the results. These improvements include: a common ordinary differential equation (ODE) integration framework that generalizes computational implementations of Integral Boundary Layer methods; the use of a dense output Runge-Kutta ODE solver that allows for querying of simulation results at any point with accuracy to the same order as …

A Flat Plate Skin Friction Correlation Including Transition, Jaret M. Wedow

Master's Theses

Many existing boundary layer models treat transition as a rapid switch from laminar to turbulent flow, with correlations defining properties in each respective region. Natural transition, however, is not always a very spanwise uniform process, with the onset of transition varying somewhat between different streamwise paths of fluid flow. Thus, a spanwise average of natural transition can result in a more gradual, extended transition region than many existing models predict. Modern applications, such as aircraft wings and fuselages, are extremely streamlined and smooth, allowing for natural transition to occur rather than flow tripping to turbulent near the leading edge. Under …

Analytical, Numerical, And Computational Methods To Analyze The Time To Empty Open, Closed, And Variable-Topped Inverted Bottles, Callen Schwefler

Master's Theses

Recent unexpected experimental observations of the emptying of inverted bottles with perforations has generated interest in modeling and simulation of this phenomenon. It was observed that as a perforation, i.e., a small hole at the "top" of the inverted bottle, is added and enlarged, the overall emptying time first increases to a maximum value and then decreases until it reaches a lower limit. The change in emptying time is associated with a transition from jetting, where only water exits the neck, to glugging, a competition between air and water flows at the neck of the bottle.

This paper develops analytical …

Development Of A Hybrid Particle Continuum Solver, Anthony J. Gay

Master's Theses

When simulating complex flows, there are some physical situations that exhibit large fluctuations in particle density such as: planetary reentry, ablation due to arcing, rocket exhaust plumes, etc. When simulating these events, a high level of physical accuracy can be achieved with kinetic methods otherwise known as particle methods. However, this high level of physical accuracy requires large amounts of computation time. If the simulated flow is in collisional equilibrium, then less computationally intensive continuum methods, otherwise known as fluid methods, can be utilized. Hybrid Particle-Continuum (HPC) codes attempt to blend particle and fluid solutions in order to reduce computation …

Development Of An Infrared Thermography System To Measure Boundary Layer Transition In A Low Speed Wind Tunnel Testing Environment, Damien Horton

Master's Theses

The use of infrared thermography for boundary layer detection was evaluated for use in the Cal Poly Low Speed Wind Tunnel (LSWT) and recommendations for the successful use of this technique were developed. In cooperation with Joby Aviation, an infinite wing model was designed, manufactured and tested for use in the LSWT. The wing was designed around a custom airfoil profile specific for this project, where the nearly-flat pressure gradient at a zero pitch angle would delay the chordwise onset of boundary layer transition. Steady-state, RANS numerical simulations predicted the onset of transition to occur at 0.75 x/c for the …

Ram Air-Turbine Of Minimum Drag, Raymond Akagi

Master's Theses

The primary motivation for this work was to predict the conditions that would yield minimum drag for a small Ram-Air Turbine used to provide a specified power requirement for a small flight test instrument called the Boundary Layer Data System. Actuator Disk Theory was used to provide an analytical model for this work.

Classic Actuator Disk Theory (CADT) or Froude’s Momentum Theory was initially established for quasi-one-dimensional flows and inviscid fluids to predict the power output, drag, and efficiency of energy-extracting devices as a function of wake and freestream velocities using the laws of Conservations of Mass, Momentum, and Energy. …

Field Testing The Effects Of Low Reynolds Number On The Power Performance Of The Cal Poly Wind Power Research Center Small Wind Turbine, John B. Cunningham

Master's Theses

This thesis report investigates the effects of low Reynolds number on the power performance of a 3.74 m diameter horizontal axis wind turbine. The small wind turbine was field tested at the Cal Poly Wind Power Research Center to acquire its coefficient of performance, C­_p, vs. tip speed ratio, λ, characteristics. A description of both the wind turbine and test setup are provided. Data filtration and processing techniques were developed to ensure a valid method to analyze and characterize wind power measurements taken in a highly variable environment. The test results demonstrated a significant drop in the …

Numerical Analysis Of A Circulation Control Wing, Luke W. Bodkin

Master's Theses

The objective of this thesis was to develop an experimental method to research circulation control wings using numerical analysis. Specifically, it is of interest to perform 3D wind tunnel testing on a circulation control wing in the Cal Poly Low Speed Wind Tunnel (CPLSWT). A circulation control wing was designed and analyzed to determine the feasibility of this testing.

This study relied on computational fluid dynamics (CFD) simulations as a method to predict the flow conditions that would be seen in a wind tunnel test. A CFD simulation was created of a wing model in a wind tunnel domain. Due …

Hypersonic Heat Transfer Load Analysis In Star-Ccm+, Robert Comstock

Master's Theses

This thesis investigates the capabilities of STAR-CCM+, a Computational Fluid Dynamics (CFD) software owned by Siemens, in predicting hypersonic heat transfer loads on forward-facing surfaces. Results show that STAR-CCM+ predicted peak heat transfer loads within +/- 20% of experimental data on the leading edge of a delta wing design from the X-20 Dyna-Soar program with 73^o of sweep. Steady-state laminar simulations were run as replications of wind tunnel tests documented in NASA CR-535, a NASA technical report that measured and studied the hypersonic pressure and heat transfer loads on preliminary X- 20 wing designs across a wide range of …

A Study Of The Utilization Of Panel Method For Low Aspect Ratio Wing Analysis, William Barton D. Newey

Master's Theses

This study demonstrates the applicability of using a modified application strategy of panel method to analyze low aspect ratio wings at preliminary design phases. Conventional panel methods fail to capture the leading edge vortex (LEV) that is shed by wings with low aspect ratios, typically below 2 depending on planform. This aerodynamic phenomenon contributes to a significant amount of the lift of these wings and the result is a drastic underestimation of the lift characteristics when analyzed by conventional panel method. To capture the effect of the leading edge vortex, a panel method code was used with an extended definition …

A Study Of The Design Of Adaptive Camber Winglets, Justin J. Rosescu

Master's Theses

A numerical study was conducted to determine the effect of changing the camber of a winglet on the efficiency of a wing in two distinct flight conditions. Camber was altered via a simple plain flap deflection in the winglet, which produced a constant camber change over the winglet span. Hinge points were located at 20%, 50% and 80% of the chord and the trailing edge was deflected between -5° and +5°. Analysis was performed using a combination of three-dimensional vortex lattice method and two-dimensional panel method to obtain aerodynamic forces for the entire wing, based on different winglet camber configurations. …

A Parametric Study Of Formation Flight Of A Wing Based On Prandtl's Bell-Shaped Lift Distribution, Kyle S. Lukacovic

Master's Theses

The bell-shaped lift distribution (BSLD) wing design methodology advanced by Ludwig Prandtl in 1932 was proposed as providing the minimum induced drag. This study used this method as the basis to analyze its characteristics in two wing formation flight. Of specific interest are the potential efficiency savings and the optimal positioning for formation flight. Additional comparison is made between BSLD wings and bird flight in formation.

This study utilized Computational Flow Dynamics (CFD) simulations on a geometric modeling of a BSLD wing, the Prandtl-D glider. The results were validated by modified equations published by Prandtl, by CFD modeling published by …

Conceptual Design Of A South Pole Carrier Pigeon Uav, Kendrick M. Dlima

Master's Theses

Currently, the South Pole has a large data problem. It is estimated that 1.2 TB of data is being produced every day, but less than 500 GB of that data is being uploaded via aging satellites to researchers in other parts of the world. This requires those at the South Pole to analyze the data and carefully select the parts to send, possibly missing out on vital scientific information. The South Pole Carrier Pigeon will look to bridge this data gap.

The Carrier Pigeon will be a small unmanned aerial vehicle that will carry a 30 TB solid-state hard drive …

A Study Of The Standard Cirrus Wing Lift Distribution Versus Bell Shaped Lift Distribution, William H. Bergman

Master's Theses

This thesis discusses a comparison of the differences in aerodynamic performance of wings designed with elliptical and bell-shaped lift distributions. The method uses a Standard Cirrus sailplane wing with a lift distribution associated with the induced drag benefits of an elliptical distribution (span efficiency = 0.96) as the basis of comparison. The Standard Cirrus is a standard class sailplane with 15-meter wingspan that was designed by Schempp-Hirth in 1969. This sailplane wing was modeled and analyzed in XFLR5, then validated against existing wind tunnel airfoil data, and Standard Cirrus flight test data. The root bending moment of the baseline wing …

Dynamic Pressure Sensing For The Flight Test Data System, Marc Y. Goupil

Master's Theses

This thesis describes the design, assembly, and test of the FTDS-K, a new device in the Boundary Layer Data System (BLDS) family of flight data acquisition systems. The FTDS-K provides high-frequency, high-gain data acquisition capability for up to two pressure sensors and an additional three low-frequency pressure sensors. Development of the FTDS-K was separated into a core module, specialized analog subsystem, and practical testing of the FTDS-K in a flow measurement mission. The core module combines an nRF52840-based microcontroller module, switching regulator, microSD card, real-time clock, temperature sensor, and trio of pressure sensors to provide the same capabilities as previous-generation …

Investigation Of The Under-Body Flow Field Of A Prototype Long-Range Electric Vehicle, Matthew P. Nguyen

Master's Theses

This thesis presents changes to the design of the Prototype Vehicles Laboratory (PROVE Lab) Endurance Car, an electric car intended to break the Guinness World Record for the single-charge range of an electric vehicle. The design range is 1609.34 km, however at the design velocity of 104.6 kph, the drag is 196 N; which requires more battery capacity than the 100 kWh maximum of the baseline model. With a fixed frontal area, drag reduction can come from lowered velocity or reduced CD. CD reduction is attempted in four ways: side skirts between the fenders, a raised ride height, an elongated …

Experimental Investigation Into Utilizing Synthetic Jet Actuators To Suppress Bi-Modal Wake Behavior Behind An Ahmed Body, Daniel Jacob Baratta

Master's Theses

Testing done on the flat-back Ahmed Body and other bluff bodies has shown the existence of a bi-stable reflectional symmetry-breaking wake at Reynolds numbers ranging from 340 to 2.41 x 10⁶. Several methods of flow control, both active and passive, have been used to improve the efficiency of the Ahmed body but their effect on the bi-stable nature of the wake has not been investigated. This work details the experimental investigation done to determine if piezoelectrically driven synthetic jet actuators are capable of suppressing the bi-stable wake effects observed behind the Ahmed Body. The synthetic jets were designed …

A Homegrown Dsmc-Pic Model For Electric Propulsion, Dominic Charles Lunde

Master's Theses

Powering spacecraft with electric propulsion is becoming more common, especially in CubeSat-class satellites. On account of the risk of spacecraft interactions, it is important to have robust analysis and modeling tools of electric propulsion engines, particularly of the plasma plume. The Navier-Stokes equations used in classic continuum computational fluid dynamics do not apply to the rarefied plasma, and therefore another method must be used to model the flow. A good solution is to use the DSMC method, which uses a combination of particle modeling and statistical methods for modeling the simulated molecules. A DSMC simulation known as SINATRA has been …

Sweep And Taper Analysis Of Surfboard Fins Using Computational Fluid Dynamics, Brandon James Baldovin

Master's Theses

The research presented here provides a basis for understanding the hydrodynamics of surfboard fin geometries. While there have been select studies on fins there has been little correlation to the shape of the fin and its corresponding hydrodynamic performance. This research analyzes how changing the planform shape of a surfboard fin effects its performance and flow field. This was done by isolating the taper and sweep distribution of a baseline geometry and varying each parameter individually whilst maintaining a constant span and surface area. The baseline surfboard fin was used as a template in Matlab to generate a set of …

A Higher-Order Method Implemented In An Unstructured Panel Code To Model Linearized Supersonic Flows, Jake Daniel Davis

Master's Theses

Since their conception in the 1960s, panel codes have remained a critical tool in the design and development of air vehicles. With continued advancement in computational technologies, today's codes are able to solve flow fields around arbitrary bodies more quickly and with higher fidelity than those that preceded them. Panel codes prove most useful during the conceptual design phase of an air vehicle, allowing engineers to iterate designs, and generate full solutions of the flow field around a vehicle in a matter of seconds to minutes instead of hours to days using traditional CFD methods. There have been relatively few …

Investigating The Effect Of An Upstream Spheroid On Tandem Hydrofoils, Joel Tynan Guerra

Master's Theses

This thesis documents a series of three dimensional unsteady Reynolds Averaged Navier-Stokes CFD simulations used to investigate the influence of an upstream prolate spheroid body on tandem pitching hydrofoils. The model is validated by performing separate CFD simulations on the body and pitching hydrofoils and comparing results to existing experimental data. The simulations were run for a range of Strouhal numbers (0.2-0.5) and phase differences (0-π). Results were compared to identical simulations without an upstream body to determine how the body affects thrust generation and the unsteady flow field.

The combined time-averaged thrust increases with Strouhal number, and is highest …

Bi-Stability In The Wakes Of Platooning Ahmed Bodies, Daniel M. Stalters

Master's Theses

Autonomous heavy vehicles will enable the promise of decreased energy consumption through the ability to platoon in closer formation than is currently safe or legal. It is therefore increasingly important to understand the complex and dynamic wake interactions between vehicles operating in close proximity for aerodynamic gains. In recent years, a growing body of research has documented a bi-stable, shifting wake generated behind the Ahmed reference bluff body. At the same time, studies of platooning Ahmed bodies have focused on changes to the body forces and moments at different following distances or lateral offsets, typically based around time-averaged measurements or …

A Computational Fluid Dynamics (Cfd) Analysis Of The Aerodynamic Effects Of The Seams On A Two-Dimensional Representation Of A Soccer Ball, Allen R. Rohr

Master's Theses

Most major sports today use a dedicated ball or projectile with specific shape, size, and surface geometry, except for soccer. Over the history of the sport, the surface geometry and design stayed relatively unchanged, sewn together using 32 pentagonal and hexagonal panels. However, recent innovations in panel designs differ substantially from the traditional 32 panel ball. The effects these new designs have on the aerodynamic characteristics of the ball have remained largely unknown, even with the influx of experimental research completed in the past decade. Experimental studies have been broad in scope, analyzing an entire ball in wind tunnels or …

The Development And Validation Of Sinatra: A Three-Dimensional Direct Simulation Monte Carlo (Dsmc) Code Written In Object-Oriented C++ And Performed On Cartesian Grids, David Matthew Galvez

Master's Theses

The field of Computational Fluid Dynamics (CFD) primarily involves the approximation of the Navier-Stokes equations. However, these equations are only valid when the flow is considered continuous such that molecular interactions are abundant and predictable. The Knudsen number, $Kn$, which is defined as the ratio of the flow's mean free path, $\lambda$, to some characteristic length, $L$, quantifies the continuity of any flow, and when this parameter is large enough, alternative methods must be employed to simulate gases. The Direct Simulation Monte Carlo (DSMC) method is one which simulates rarefied gas flows by directly simulating the particles that compose the …