Architecture Commons^™

Effect Of Type And Quantity Of Inherent Alkali Cations On Alkali-Silica Reaction, Pengfei Ma, Jiaoli Li, Jincheng Bai, Ying Zhuo, Lingyu Chi, Yanping Zhu, Zhenhua Shi, Hongyan Ma, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this study, the macroscopical expansion induced by alkali-silica reaction (ASR) and its corresponding ASR products are investigated using ordinary Portland cement (OPC) mortar specimens with a gradient of boosted alkalis. Experimental results show that the expansion increases with the concentration of inherent alkalis. Sodium-boosted samples expand approximately three times as much as potassium-boosted samples. ASR gels that are present in aggregate veins are calcium-free and amorphous; the atomic ratios of ASR gels are nearly independent of the type and quantity of alkali cations. Aggregate ASR gel exudation occurs in high (≥2.5 %) sodium cases and produces potential Na-shlykovite. Crystalline …

Understanding Collaboration Requirements For Modular Construction And Their Cascading Failure Impact On Project Performance, Mohamad Abdul Nabi, Amr Elsayegh, Islam H. El-Adaway

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Effective Implementation of Modularization Demands Close Collaboration among the Various Project Stakeholders Due to the Distinct and Complex Needs of Such Construction Method. in Fact, Lack of Adequate Collaboration is One of the Main Factors Impacting Modular Construction Performance. Despite that, No Previous Study Has Yet Addressed Collaboration Requirements in Modular Construction and their Cascading Failure Impact on Project Performance. This Paper Fills Such a knowledge Gap. to This End, the Authors Followed a Multistep Research Methodology. First, Systematic Literature Analysis Was Performed to Identify the Factors Impacting Collaboration and the Impacted Modular Risks as Well as their Cause-Effect Relationships. …

Evaluation Of Residual Flexural Behavior Of Corroded Fiber-Reinforced Super Workable Concrete Beams, Jingjie Wei, Nima Farzadnia, Alfred Addai-Nimoh, Kamal Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This Study Investigates the Effect of Macro Synthetic Fiber (MSF) Volume and Crack Widths on Corrosion of the Reinforcing Bars and Residual Flexural Behavior of Fiber-Reinforced Super-Workable Concrete (FR-SWC) Beams Exposed to Accelerated Corrosion. FR-SWC Beams Prepared with 0, 0.33%, and 0.66% MSF Were Pre-Cracked at 0.2-, 0.4-, and 0.75-Mm Widths Before Corrosion Testing. the Controlled Crack Width Was Initiated in One Set of Beams that Were Then Unloaded. the Crack Width Was Maintained for Another Set of Beams during Corrosion Testing by Inserting a Shim. Test Results Showed that the Use of 0.33% and 0.66% MSF Reduced Crack Development …

Cement-Based Materials With Solid-Gel Phase Change Materials For Improving Energy Efficiency Of Building Envelope, Zhuo Liu, Jiang Du, Ryan Steere, Joshua P. Schlegel, Kamal Khayat, Weina Meng

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

This paper evaluated the cement-based materials incorporated with novel solid-gel phase change materials (PCMs) for improving the energy efficiency of building envelopes. This novel PCM is form-stable, which will not leak as solid-liquid PCMs do and not need encapsulation, and it features high energy-storage capacity. Experimental results showed that the thermal properties of cement-based materials were improved as the increase of PCM content. A 30% replacement of sand by volume with PCM can increase the latent heat of the mixture from around 0 to 7 J/g and decrease the thermal conductivity of PCM mortar based on the generalized self-consistent (GSC) …

Evaluation Of Feasibility And Performance Of Foamed Fire-Resistant Coating Materials, Anyou Zhu, Hanli Wu, Yizhuang David Wang, Jenny Liu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

A preliminary study found high-performance cement mortar, geopolymer mortar, and magnesium phosphate cement mortar (MPCM) have the potential as new fire-resistant materials. In this study, foam was added to these three fire-resistant materials to further improve their rheological, mechanical, and fire-resistant performance and reduce costs. Systematic design and experimental programs were conducted. The results showed the addition of foam enhanced workability, adhesiveness, and fire resistance, allowing the materials to withstand higher temperatures and further delay heat transfer. A mixture of 70% MPCM and 30% foam was identified as the optimum design, which could withstand 1000 °C with low heat transfer …

Improving Rheological And Thermal Performance Of Gilsonite-Modified Binder With Phase Change Materials, Farshad Saberi K., Yizhuang David Wang, Jenny Liu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Gilsonite, as a type of natural asphalt binder, has been used to improve the high-temperature performance of regular asphalt binders. However, the addition of Gilsonite may compromise binders' low-temperature thermal cracking resistance. In this research, polyethylene glycol (PEG), as one type of the phase change materials (PCMs), was used as an innovative material to balance the impacts of Gilsonite on high and low performance of asphalt binders. The dosages of Gilsonite and PEG were first determined based on the materials' rheological behaviors at low temperatures. The performance of the PEG-Gilsonite-modified binder was then fully evaluated in terms of the resistance …

Mechanism Underlying Effect Of Expansive Agent And Shrinkage Reducing Admixture On Mechanical Properties And Fiber-Matrix Bonding Of Fiber-Reinforced Mortar, Kamran Aghaee, Taihao Han, Aditya Kumar, Kamal Khayat

Materials Science and Engineering Faculty Research & Creative Works

Expansive agent (EA) and shrinkage reducing admixture (SRA) are utilized to reduce shrinkage and risk of cracking in concrete. EA compensates shrinkage by initial expansion, and SRA reduces surface tension in the pore fluid. Although EA and SRA effectively reduce shrinkage, they can impair micro-structure of concrete at high contents. The shrinkage reduction effect of EA and SRA is well known; however, there is limited knowledge about their negative effect on microstructure and fiber matrix interfacial transition zone (ITZ). The current study explores the effect of using 10 % CaO-based EA, 2 % SRA, and their combination on mechanical, shrinkage, …

Preface: Special Issue On Turbulence And Mixing In Stratified Flows, S. Karan Venayagamoorthy

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

No abstract provided.

Mixing Rates In Stably Stratified Flows With Respect To The Turbulent Froude Number And Turbulent Scales, Matthew R. Klema, Subhas Karan Venayagamoorthy

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this analysis the quantification of diapycnal diffusivity Kρ in stratified flows such as those found in the ocean and atmosphere is explored. There are two simplifications that are routinely made when estimating mixing rates in stably stratified flows. First, a constant value is commonly assumed for the (irreversible) mixing coefficient Γ . Second, dissipation rates of turbulent kinetic energy ϵ are inferred using either the Thorpe (or Ellison) length scales or from microstructure measurements using the isotropy assumption. Data from three independent direct numerical simulations of homogeneous stratified turbulence are used as a testbed to highlight impacts of these …

Effect Of Rotation On Mixing Efficiency In Homogeneous Stratified Turbulence Using Unforced Direct Numerical Simulations, Matthew Klema, S. Karan Venayagamoorthy, Annick Pouquet, Duane Rosenberg, Raffaele Marino

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Diapycnal (irreversible) mixing is analyzed using thirty direct numerical simulations (at 1024 ³ resolution) of homogeneous rotating stratified turbulence (RST) in the absence of imposed shear or forcing. The influence of varied rotation and stratification rates on the energetics (in particular the dissipation rates of kinetic and potential energies) is presented. Data is also analyzed within a new parametric framework, using the turbulent Froude and Rossby numbers Frt= ϵ/ Nk, Rot= ϵ/ fk, where k is the turbulent kinetic energy, ϵ its rate of dissipation, N the buoyancy frequency and f the Coriolis parameter. This framework is used to illustrate …

Rilem Tc 266-Mrp: Round-Robin Rheological Tests On High Performance Mortar And Concrete With Adapted Rheology—Evaluating Structural Build-Up At Rest Of Mortar And Concrete, Sofiane Amziane, Kamal Khayat, Mohammed Sonebi, Arnaud Perrot

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This Paper Presents the Results of a Round-Robin Testing Program Undertaken by RILEM TC-266-Measuring Rheological Properties of Cement-Based Materials in May 2018 at the Université D'Artois in Bethune, France. Seven Types of Rheometers Were Compared; They Consisted of Four ICAR Rheometers, Viskomat XL Rheometer, EBT-V Rheometer, Sliding Pipe Rheometer (SLIPER), RheoCAD Rheometer, and 4SCC Rheometer, as Well as the Plate Test. This Paper Discusses the Results of the Evolution of the Static Yield Stress at Rest of Three Mortar and Five Concrete Mixtures that Were Determined using Two ICAR Rheometers, Viskomat XL, and EBT-V Rheometers, as Well as the Plate …

Atomic Insights Into The Structural Properties And Displacement Cascades In Ytterbium Titanate Pyrochlore (Yb2ti2o7) And High-Entropy Pyrochlores, M. Mustafa Azeem, Qingyu Wang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Pyrochlore oxides ((Formula presented.) are potential nuclear waste substrate materials due to their superior radiation resistance properties. We performed molecular dynamics simulations to study the structural properties and displacement cascades in ytterbium titanate pyrochlore ((Formula presented.)) and high-entropy alloys (HEPy), e.g., (Formula presented.), (Formula presented.), and (Formula presented.). We computed lattice constants (LC) ((Formula presented.)) and threshold displacement energy (Ed). Furthermore, the calculation for (Formula presented.) and ionic radius ((Formula presented.)) were performed by substituting a combination of cations at the A and B sites of the original pyrochlore structure. Our simulation results have demonstrated that the lattice constant is …

Common Ground Newsletter Fall 2023, Missouri University Of Science And Technology

Common Ground

- Free-Format Education

- S&T student selected as national ASCE ambassador

- Heart of a servant

- Exploring history, architecture of Chicago

Introduction To 'Artificial Intelligence In Failure Analysis Of Transportation Infrastructure And Materials', Yue Hou, Qiao Dong, Dawei Wang, Jenny Liu

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Transportation infrastructures, including roads, bridges, tunnels, stations, airports and subways, play fundamental roles in modern society. Engineering failures of transportation infrastructures may result in significant damage to the public. The traditional methods are to monitor, store and analyze the information during the infrastructure and material design, testing, construction, numerical simulations, evaluation, operation, maintenance and preservation, using mechanistic-based, material based and statistics-based approaches. In recent decades, artificial intelligence (AI) has drawn the attention of many researchers and has been used as a powerful tool to understand and analyze the engineering failures in transportation infrastructure and materials. AI has the advantages of …

In Situ Monitoring Of The Hydration Of Calcium Silicate Minerals In Cement With A Remote Fiber-Optic Raman Probe, Bohong Zhang, Wenyu Liao, Hongyan Ma, Jie Huang

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study utilized a novel in situ fiber-optic Raman probe to continuously monitor the hydration progress of tricalcium silicate (C₃S) and dicalcium silicate (C₂S) without the need for sampling, from early hydration stage to later stages, and from fresh to hardened states of paste samples. By virtue of the remarkable ability of this technique in characterizing either dry or wet and crystalline or amorphous samples, the hydration processes of C₃S and C₂S pastes with different water-to-solid (w/s) ratios could be monitored from the start of the hydration reaction. The main hydration products, …

Behavior Of Ultrahigh-Performance Concrete Plates Encasing Steel H-Piles, Mohamed Elgawady, Binod Shrestha

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Steel H-piles are exposed during their service life to wet-dry cycles in combination with salts, such as deicing, that may result in corrosion, leading to cross-sectional loss and reduction in axial load-carrying capacity. This paper proposes an innovative repair method for corroded steel H-piles using ultrahigh-performance concrete (UHPC) plates. The UHPC plates are reinforced with carbon fiber-reinforced polymer (CFRP) grids. The UHPC plates bridge the corroded segment so that the axial force bypasses the corroded segment. The UHPC are bolted to the steel H-pile using high-strength bolt connectors (HSBCs). Eleven steel H-piles bolted with UHPC plates were investigated experimentally under …

Utilizing Waste Latex Paint Toward Improving The Performance Of Concrete, Mohamed Leithy, Eslam Gomaa, Ahmed A. Gheni, Mohamed Elgawady

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this paper, incorporating the waste latex paint (WLP) into the conventional concrete as a partial replacement of sand to improve its durability was investigated. The fresh and hardened characterizations, in addition to the durability of concrete, were examined. The slump test was used to evaluate the fresh properties, while the hardened properties were evaluated through the volume of voids and absorption rate, in addition to the compressive, splitting tensile, and flexural strengths tests. The durability performance was evaluated by the surface resistivity, bulk electrical resistivity, as well as freeze and thaw resistance tests. The results showed a reduction in …

Machine Learning-Based Seismic Damage Assessment Of Residential Buildings Considering Multiple Earthquake And Structure Uncertainties, Xinzhe Yuan, Liujun Li, Haibin Zhang, Yanping Zhu, Genda Chen, Cihan H. Dagli

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Wood-frame structures are used in almost 90% of residential buildings in the United States. It is thus imperative to rapidly and accurately assess the damage of wood-frame structures in the wake of an earthquake event. This study aims to develop a machine-learning-based seismic classifier for a portfolio of 6,113 wood-frame structures near the New Madrid Seismic Zone (NMSZ) in which synthesized ground motions are adopted to characterize potential earthquakes. This seismic classifier, based on a multilayer perceptron (MLP), is compared with existing fragility curves developed for the same wood-frame buildings near the NMSZ. This comparative study indicates that the MLP …

Development And Characterization Of Coal-Based Thermoplastic Composite Material For Sustainable Construction, Haibin Zhang, Wenyu Liao, Genda Chen, Hongyan Ma

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The exploitation of coal and the disposal of waste plastic present significant environmental and economic challenges that require sustainable and profitable solutions. In response, we propose a renewable construction composite material of coal-based thermoplastic composite (CTC) that can be made from low-grade coal and plastic waste. We developed and tested the hot-press fabrication method for this CTC, using coal with a maximum particle size of 4.75 mm and recycled high-density polyethylene (HDPE). The effects of the coal fraction (50–80 wt.%) on compressive properties, thermal properties, microstructure, and ecological and economic efficiencies of the CTC were investigated. Test results revealed that …

Effect Of Competitive Adsorption Between Specialty Admixtures And Superplasticizer On Structural Build-Up And Hardened Property Of Mortar Phase Of Ultra-High-Performance Concrete, Le Teng, Jingjie Wei, Kamal Khayat, Joseph J. Assaad

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This study aims to enhance structural build-up of ultra-high-performance concrete (UHPC) without influencing the initial flowability, which is critical in repair applications (e.g., use of UHPC in thin bonded overlays for bridge deck rehabilitation). Specialty admixtures, such as a viscosity-modifying admixture (VMA), have been used to enhance the structural build-up at rest. However, the use of specialty admixtures can increase superplasticizer (SP) demand to maintain proper flowability; the synergistic effect of these admixtures on structural build-up is not well understood as the coupled admixture content can reverse the net effect on yield stress, viscosity, and thixotropy. In this study, VMAs …

A Spike-Shaped Anchorage For Steel Reinforced Polymer (Srp)-Strengthened Concrete Structures, Xingxing Zou, Keenan L. Mcburney, Lesley H. Sneed

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Steel reinforced polymer (SRP) composite has recently emerged as an effective and economical solution for strengthening of reinforced concrete (RC) structures. Premature debonding failure of unanchored SRP at low load levels generally governs the performance of RC structures strengthened with externally bonded SRP. Therefore, a novel yet simple spike-shaped anchorage system was proposed in this study to prevent the debonding failure of SRP and to improve the interfacial shear capacity. Experimental investigation through single-lap shear tests of SRP-concrete joints showed that the anchorage system changed the failure mode from composite debonding to fiber rupture. In addition, the anchorage system substantially …

Experiential Learning And Exposure To Professional Experience In Civil Engineering Education, Sanjay Tewari

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Experiential learning is increasingly recognized as a crucial component of modern education, especially in fields like civil engineering, where practical skills and real-world exposure are paramount. This paper explores the various avenues through which civil engineering education can offer professional exposure and experiential learning opportunities. By analyzing the impact of senior seminars, internships, co-ops, undergraduate research, study abroad programs, service learning, student design teams, leadership positions, and involvement in technical and professional student organizations, this paper aims to underscore the importance of these approaches in shaping well-rounded and industry-ready civil engineers.

Effect Of Internal Curing And Shrinkage-Mitigating Materials On Microstructural Characteristics Of Fiber-Reinforced Mortar, Kamran Aghaee, Kamal Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Internal curing (IC) and other shrinkage mitigating materials are employed to reduce shrinkage and risk of cracking. This study investigates the efficiency of individual versus combined use of IC and shrinkage mitigating materials on key characteristics of fiber-reinforced mortar (FRM). The investigated mixtures include a 25% pre-saturated lightweight sand (LWS) that is added individually and combined with 10% CaO-based expansive agent (EA) and 2% shrinkage reducing admixture (SRA). This elucidates the synergistic effect of high content IC and EA/SRA on macro- and micro-mechanical characteristics of FRM, especially at the interface of the matrix with fibers. Mechanical properties, microstructural characteristics, and …

Viscoelastic Properties Of Fresh Cement Paste: Measuring Procedures And Influencing Parameters, Ammar Yahia, Arnaud Perrot, Dimitri Feys, Kamal Khayat, Mohammed Sonebi, Shiho Kawashima, Wolfram Schmidt

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Fresh cement pastes behave as viscoelastic materials below the flow onset. The measurements of viscoelastic properties of fresh cement paste provide valuable insight into the dispersion of solid particles as well as the hydration kinetics at early age and its influence on the structural evolution and solidification behavior at quasi-static conditions. Monitoring the development of viscoelastic properties of fresh cement paste using dynamic oscillatory shear measurements can also elucidate the working mechanisms of chemical admixtures. These properties are efficient indicators to guide mixture proportion design and are necessary to understand the rheology and stability of concrete. In this paper, the …

Prediction Of Compressive Strength And Evaluation Of Different Theoretical Standards And Proposed Models Of Brick Columns Confined With Frp, Frcm, Or Srg System, Zuhair Al-Jaberi, John J. Myers

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Strength Capacity of Confined Masonry Column is One of the Topics that Need to Be Studied. in This Study, the Efficiency of using Different Types of Advanced Composite (Non-Corrosive Materials) Such as Fiber Reinforced Polymer (FRP), Fiber Reinforced Cementitious Matrix (FRCM), or Steel Reinforced Grout (SRG) in Confining Masonry Columns is Investigated. a Wide Range of Experimental Database of Masonry Column Specimens Has Been Collected from the Results that Available in Scientific Literatures. Different Theoretical Standards and Proposed Models that Used to Predict the Capacity of Masonry Columns Confined with FRP and FRCM Are Evaluated based on Collected Experimental …

On The Development Of Part-Scale Fem Modeling For Laser Powder Bed Fusion Of Aisi 316l Stainless Steel With Experimental Verification, Muhammad Arif Mahmood, Asif Ur Rehman, M. Mustafa Azeem, Abedalkader Alkhouzaam, Marwan Khraisheh

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In laser powder bed fusion (LPBF), the effects of operating conditions on thermal gradients and residual stresses are the utmost challenges that require significant attention. The magnitudes of residual stress in the printed layers, as well as the distribution along the printed components, have not been well explained for LPBF parts. In this study, a 3D finite element thermo-mechanical model has been established to investigate the effect of operating conditions on thermal distribution, melt pool evolution, residual stress distribution, and part distortion. The printed AISI 316L stainless steel cubes have been characterized experimentally. The results showed a proportional correlation among …

Rejuvenation Effect Of Aged Sbs-Modified Asphalt Utilizing Molecule Analysis, Ke Shi, Feng Ma, Jenny Liu, Zhen Fu, Ruimeng Song, Dongdong Yuan, Chen Li

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

The Performance of Styrene-Butadiene-Styrene Modified Asphalt (SBSMA) is Significantly Impacted by its Aging and Regeneration. in This Research, the Molecular Dynamics Simulation Was Utilized to Investigate the Rejuvenation Effect of Active Reagents on Aged SBS Modified Asphalt through the Following Tasks: 1) Verifying the Accuracy of the Asphalt Model by Density and Solubility Parameters; 2) Assessing the Changes in the Rejuvenated Asphalt Model's Energetic Parameters and Volume Parameters, 3) Studying the Interaction Energy between SBS Molecules and Asphalt Molecule Models, and 4) Evaluating the Relative Concentration, Interfacial Interaction Energy, and Diffusion Effect of the Asphalt-Asphalt Models. the Results Indicated that …

Automated Detection And Characterization Of Cracks On Concrete Using Laser Scanning, Yunfeng Ge, Jenny Liu, Xiong Zhang, Huiming Tang, Xiaolong Xia

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Accurate crack detection and characterization on concrete are essential for the maintenance, safety, and serviceability of various infrastructures. In this paper, an innovative approach was developed to automatically measure the cracks from 3D point clouds collected by a phase-shift terrestrial laser scanner (TLS) (FARO Focus3D S120). The approach integrates several techniques to characterize the cracks, which include the deviation on point normal determined using k-nearest neighbor (kNN) and principal components analysis (PCA) algorithms to identify the cracks, and principal axes and curve skeletons of cracks to determine the projected and real dimensions of cracks, respectively. The coordinate transformation was then …

Field Implementation And Performance Of Fiber-Reinforced Low-Shrinkage Concrete For Bridge Deck Construction, Ahmed Abdelrazik, Kamal Khayat

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This Paper Reports on the Field Implementation of Fiber-Reinforced Concrete (FRC) Used for Redecking the Two-Span overpass Bridge in Missouri. the Spans Measured 38.4 and 35.05 M in Length. Modeling of the Structural Behavior of the Bridge Replacement Deck Indicated Significantly High Tensile Stresses at Midspan (Up to 45 MPa) Due to the Continuity of the Deck over the Four Precast Main Girders. Redecking of the Bridge and Casting of the Central Diaphragm Were Carried Out Continuously and Necessitated 40 Concrete Truck Deliveries of 252 M3 of FRC. Six Sensor Towers Were Installed in the Bridge Deck to Monitor Variations …

Preliminary Bond Capacity Exploration Between Monolayer Graphene And Cementitious Composites, Yanping Zhu, Chuanrui Guo, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

This Study Aims to Explore Bond Capacity between Monolayer Graphene and Cementitious Composites for the First Time through a Pullout Test. the Low-Pressure Chemical Vapor Deposition Method Was Used to Synthesize Monolayer Graphene on the Copper Substrate to Be Embedded in the Mortar Made by the Briquette Mold. the Bond Capacity between Them Was Higher Than the Tensile Strength of the Copper Sheet with As-Grown Monolayer Graphene on the Surface Since All Specimens Failed in Fracture with Embedment Length of More Than 30 Mm. the Monolayer Graphene Enhanced the Copper Tensile Fracture Stress and Normalized Energy during the Test as …