Digital Commons Network^™

Mems 411: Talking Goniometer, Jeffrey Reinhold, Matthew Ren, Corin Riahi, Moises Rodriguez

Mechanical Engineering Design Project Class

Our project is about designing a goniometer that will aid Rachel Apter, an occupational therapy graduate student, more easily determine the angles created by limbs bending about a joint. A goniometer is essentially a protractor designed to affix its base arm to a stationary limb and it’s rotating arm to a moving limb. The moving arm follows the moving limb, measuring the coupled limb’s range of motion. The main complaint centering around goniometers is that they are hard to read due to the small tick marks that indicate the angle. To fix this problem, the goniometer will be edited to …

Mems 411: The Ball Bearing Sorter Group N, Jack Zhao, Anri Cifuentes, Shawn Xiong, Richard Li

Mechanical Engineering Design Project Class

The challenge was to design and develop an automated device capable of sorting and packaging six types of ball bearings—varying in size (1/4 inch and 1/2 inch) and material (stainless steel, brass, and nylon). The device needed to meet strict performance and design constraints, including fitting within a compact 20x20x20-inch footprint, weighing no more than 15 pounds, and sorting bearings with high speed and accuracy.

This problem represents a practical scenario in automated manufacturing, where efficient and precise sorting is crucial for streamlining assembly line operations. The solution required integrating innovative engineering mechanisms, such as size differentiation, material separation, and …

Mems 411: Mailbox Assistant, Peter Scholl, Benjamin Cortes, Garbiel Arcas, Colin Zeiss

Mechanical Engineering Design Project Class

Oftentimes elderly people struggle with reaching into their curbside mailbox from their car, especially if the mail is pushed all the way to the back. With the Mailbox Assistant, sore shoulders can be saved through a drawer that slides out from the mailbox. This modification can be made to any mailbox without altering the outside appearance thus keeping it within HOA standards.

Mems 411: Hydroponic Gardening System, Tiger Lu, Aj Shanahan, Jaquelin Guzman, Brandon Lacy

Mechanical Engineering Design Project Class

This report summarizes the engineering design process undertaken for the development of a hydroponic gardening system. The project began with selecting a concept, as a team, we decided to focus on designing a system tailored to community gardening needs. The report is organized into five main sections: Problem Understanding, Concept Generation, Concept Selection, Concept Embodiment, and Design Refinement. In the Problem Understanding phase, the team conducted extensive research on patents, codes and standards, user needs, design metrics, and project management. This foundational research was critical to ensure all aspects were considered before beginning the building process. User needs were identified …

Mems 411: Diving Surface Breaker, Chandler Gartner, Freddy Phillips, Maya Sumra, Olivia Slemmer

Mechanical Engineering Design Project Class

We have been recruited by the WashU diving team to design and construct a surface breaker for the Millstone Pool so the divers can have an affordable way to stay safe while practicing dives.

Mems 411: Timed Mosquito Egg Container Design Project, Paige Warren, Witt Ciesla, Ethan Sobel

Mechanical Engineering Design Project Class

The goal of this project is to design and construct a device that allows for the controlled study of mosquito egg-laying behavior in response to artificial light and temperature variations. Specifically, the device will limit access to cups of standing water, which serve as egg-laying sites, to preprogrammed times of day over a 7-day period.
The device should ensure the following:

• Control Access: The container should be open and closed at predetermined intervals, allowing mosquitoes to access the cups of standing water only during these times.
• Programmability: It should be easy for a novice to specify the opening and closing …

Mems 411: Ball Bearing Sorter, Abdissa Effa, Juliet Whitehead, Ayub Shifa

Mechanical Engineering Design Project Class

The challenge is to design and fabricate a compact device capable of autonomously sorting and transporting ball bearings of varying materials (chrome steel, brass, nylon) and sizes (¼” and ½”) into designated packaging stations. The device must operate efficiently, accurately, and within the constraints of a 20x20x20-inch enclosure, meeting industrial assembly line standards of speed and precision while minimizing human intervention. It aims to address the need for high-rate sorting systems in manufacturing environments, ensuring accurate material identification and classification for streamlined operations.

Mems 411: Asme Ball Bearing Sorter, Ryan Lively, Joseph Huster, Wil Collins

Mechanical Engineering Design Project Class

The ASME Student Design Competition focused on the design and construction of a ball bearing sorter. This ball bearing sorter must be capable of sorting 2 sizes of ball bearings, being 1/2 inch and 1/4 inch. For each size, there are 3 different bearing materials, brass, steel, and acetal plastic. The device is intended to have the bearings fed into a hopper, and then fully autonomously sort the bearings. The autonomous sorting was to transport the various bearings into 6 different packing stations, one for each size and material bearing. These packing stations must be easily removable. This design project …

Mems 411: Automated Assistive Toilet, Alex Scaff, Kenna Mcgahren, Daniel Sibley

Mechanical Engineering Design Project Class

How do we make toilets more accessible for all people - regardless of physical, mental, emotional impediments - while also ensuring simplicity and cost-effectiveness? Utilizing sensors, our toilet device is designed to automatically open and close the toilet lid upon approach, increasing ease of use and general hygiene of the user while being friendly to those who struggle with certain disabilities or impairments.

Mems 411: Adjustable Desk, Catryn Cattoor, Natalia Pilpil, Jamie Burgasser, Adam Wong

Mechanical Engineering Design Project Class

Design and create a desk for a special education classroom of kindergarteners to third graders. The desk needs slanting capabilities, wheel chair accessibility, raising/lower capabilities, distraction prevention capabilities, and light board capabilities. These capabilities need to be configurable for students with different needs. This desk also needs to be very durable, safe, and mobile. The main motivation for this project is the desire to provide the teacher and her students with a single, cost-effective product that is safe, easy to use, and meets their desired needs.

Mems 411: Group V Ball Bearing Sorter, Matthew Hernandez, Sean Huffert, Ethan Delair

Mechanical Engineering Design Project Class

After a semester of hard work, Team V is proud to unveil its finished prototype for the 2024-2025 ASME Student Design Competition. The theme of this challenge was "Assembly Line Sorting and Packaging." The goal of this challenge was to make a device able to satisfy the criteria of sorting between six different bearings of different sizing and material properties, and meeting spatial and time limitations. This device needed to be fast, accurate, compact, and able to sort in bulk. Team V feels like we have met most of these requirements with our final design prototype. For this project, a …

Mems 411: Rc Plane Mount For Cfd Validation, Jake Schwartz, Margot Jay, Ian Torres, Sam Ehrman

Mechanical Engineering Design Project Class

Washington University in St. Louis’ Design/Build/Fly team (WashU DBF) participates in an annual international competition with over 100 teams where they create a Remote Control (RC) plane that can perform various missions. One of the difficulties in developing a plane each year is testing the forces on the plane. Currently, Ansys and XFLR5 are used to create computational fluid dynamics (CFD) models for the plane. CFD modeling simulates air flow over the plane’s wings to analyze how to optimize the aircraft’s aerodynamics. While this is a useful strategy to predict the plane’s theoretical performance, WashU DBF Technical President, Eleni Kambouris, …

Mems 411: Mini Syringe Pump, Rachel Foulk, Braxton Hart, Camilo Hernandez

Mechanical Engineering Design Project Class

In many research and medical settings, small amounts of liquids are dispensed using syringes. Very often, syringe pumps like those shown in the left image, are used to control the amount (i.e., flow rate) of dispensed/collected fluid. There are single- or multi-style syringe pumps; the one shown is single-style; multi-style have 2-8 parallel syringes that are all pushed/pulled at the same flow rate. However, these syringe
pumps are bulky and heavy, making them impractical for many experimental setups. Commercial alternatives include very expensive syringe pumps with remote dispensers. Furthermore, it is often necessary to have two syringe pumps operate in …

Chimes: December 9, 2024, Calvin University

Chimes

“That’s not true inclusion:” For disabled students, full campus accessibility remains elusive by Sarah Sparling

Umm al-Jimal archaeological site added to UNESCO World Heritage by Grace Buller and Elisabeth Stevens

2025 January Series sees restructure and big names by Graham Kort

Changes to dining hall hours, staffing benefits leave students broadly dissatisfied by Maya Oeverman

Making worship more accessible: A Q&A with Eleanor Plutz about ASL chapel interpretation by Anna Caruso

“The Holy Spirit Made Me Dance” by Natasha Jayaputra

Inference For Regression With Variables Generated By Ai Or Machine Learning, Laura Battaglia, Timothy Christensen, Stephen Hansen, Szymon Sacher

Cowles Foundation Discussion Papers

It has become common practice for researchers to use AI-powered information retrieval algorithms or other machine learning methods to estimate variables of economic interest, then use these estimates as covariates in a regression model. We show both theoretically and empirically that naively treating AI- and ML-generated variables as “data” leads to biased estimates and invalid inference. We propose two methods to correct bias and perform valid inference: (i) an explicit bias correction with bias-corrected confidence intervals, and (ii) joint maximum likelihood estimation of the regression model and the variables of interest. Through several applications, we demonstrate that the common approach …

Ultraviolet And Blue Stimulated Emission From Cs Alkali Vapor Pumped Using Two-Photon Absorption And Four-Wave Mixing, Ricardo C. Davila, Christopher A. Rice, Nathan B. Terry, Glen P. Perram

Faculty Publications

Stimulated emission on the ultraviolet and blue transitions in Cs has been achieved by pumping via two-photon absorption and four-wave mixing for the pump transition 6²S½ → 8²D_3/2,5/2. The emission performance of the optically pumped cesium vapor laser operating in ultraviolet and blue has been extended to 650 nJ/pulse for 387 nm, 1 to 3 μ J / pulse for 388 nm, 200 nJ/pulse for 455 nm, and 500 nJ/pulse for 459 nm. Emission performance improves dramatically as the cesium vapor density is increased, and no scaling limitations associated with energy pooling or …

Comparing Recovery Volumes Of Steady And Unsteady Injections Into An Aquifer Storage And Recovery Well, Saeid Masoudiashtiani, Richard C. Peralta

Civil and Environmental Engineering Faculty Publications

Aquifer Storage and Recovery (ASR) can involve injecting available surface water into an unconfined aquifer and then extracting it to provide secondary water for irrigation. This study demonstrates a method for evaluating the appropriateness of steady injection versus unsteady injection for an assumed situation. In design, it can be important to affect the transient: the proportion of the injected water that would be subsequently extracted (versus that remaining in the aquifer) and the proportion within the extracted water that would be an injectate (versus ambient groundwater). These proportions can be predicted from the predicted value of an ASR well's Recovery …

Mae Enewsbrief July-Sept 2024, Department Of Mechanical And Aerospce Engineering, Michigan Technological University

Department of Mechanical and Aerospace Engineering eNewsBrief

No abstract provided.

Taxonomy Of Cyber Risk Mitigation Cost Benefit Analysis Methods For Energy Infrastructure, Yvonne Kam Hwei Syn, Kevin Jones, Kimberly Tam, Robert Rawlinson-Smith

School of Engineering, Computing and Mathematics

Cybersecurity is a critical aspect for the energy industry to defend against cyber attacks. However, justifying the costs of cybersecurity measures is essential. A cost-benefit analysis (CBA) is commonly used to support decision-making for risk mitigation, helping to identify strategies that optimally balance mitigation costs and risk reduction. In this survey, we analyse existing approaches and provide a taxonomic overview of methods for cyber risk mitigation cost-benefit analysis, focusing on key aspects that determine their applicability to energy systems. The survey includes both general and contextual works, employing various methodologies for CBA, whether analytical or criteria-based. We conclude with an …

Agronomic Biofortification Of Calcium In Pak Choy (Brassica Rapa Subsp. Chinensis) Via Hydroponic Nutrient Film Technique, Regina Septiani Zahro, Khavid Faozi, Zulfa Ulinnuha, Agus Sarjito

Jurnal Kultivasi

Pak choy is rich in calcium, magnesium, phosphorus, iron, and vitamin K, all essential for health. Pak choy requires a proper balance of nutrients for optimal growth. In a hydroponic system, any imbalance in nutrient levels can negatively impact plant growth and reduce the nutritional value stored in the tissues. Selecting suitable varieties and providing appropriate calcium treatment can help increase calcium content and enhance productivity. This study aims to determine the effect of calcium concentration on growth, yield, and Ca content and the most responsive varieties to increased calcium concentration. The research design used was a Split Plot Design …

The Role Of Full-Time Job Postings For Postsecondary Cte Faculty In Curriculum Design: A Document Analysis, James Bartlett Ii, Michelle Bartlett

Journal of Research in Technical Careers

This study examines job postings for full-time postsecondary Career Technical Education (CTE) faculty to explore job duties. Document analysis was used on the job postings collected on JobsEQ Real-Time Intelligence for CTE instructors in North Carolina. Over a year, 318 job postings were found through specific search terms in JobsEQ, with 205 retained. Discarded postings were due to duplication, not postsecondary CTE, or part-time positions. Examination of job postings revealed six thematic areas that tie to curricular skills: development process, inputs and standards, content of the CTE curriculum for students, uses of curriculum in the CTE instructor’s role, goals, and …

Employing The Next Generation: Defining The Need For Employability Skills Integration Through The Lens Of School District Superintendents, William Norris, Shannon L. Norris-Parish

Journal of Research in Technical Careers

Since its inception, agricultural education has been instrumental in equipping secondary graduates with the necessary skills to be successful in their future career endeavors. While this has remained a priority over time, many employers claim that secondary graduates do not possess the necessary skills to be successful in the workforce. This study sought to assess the perceptions of school-district superintendents on the importance of integrating employability skills into agricultural education courses and evaluate differences in the perceptions of male and female superintendents. We used a descriptive research design to collect the data. The instrument assessed 41 individual skills in nine …

Potential Propagation Seedling Of Ramie (Boehmeria Nivea) From Various Types Of Stem Cuttings, Taufiq Hidayat Rahman Side, Mayasari Yamin, Sri Mulyani, Agung Pangestu Aji, Luthfi Ayunawati

Jurnal Kultivasi

Ramie is a fiber-producing plant that can replace cotton as a raw material for the textile industry. In general, ramie plants are reproduced using rhizomes, but it takes a long time, around two years, to be used as a source of planting material. Therefore, other sources of explants besides rhizomes are required, such as stem cuttings. Explants from stem cuttings are quickly available and only need 2-3 months to be used as planting material. This study aims to determine the potential of effective stem cuttings that can be used as planting material for the propagation of ramie seedlings. The research …

Development Of A Stable And Buffered Reference Electrode For Binary Molten Chlorides Salts, Carlos Mejia, Nicholas Christensen, Ricardo Rodriguez Ceron, Devin Rappleye

Faculty Publications

The development of stable and buffered reference electrodes (REs) is crucial for molten salt electrochemistry, particularly in pyrochemical processing, such as electrorefining. These REs must maintain a stable potential to ensure precise control over electrorefining processes by preventing unwanted shifts in the potential that could lead to impurity deposition. This study evaluated metal chlorides and metal oxides as potential candidates for REs, with their stability assessed via electrochemical methods over extended durations. While metal chloride-based REs exhibited stable potential behavior over time, their response followed the Nernst equation, leading to potential shifts with varying concentrations of oxidized species. Metal oxide-based …

Four Iwu Students Receive Funding To Develop Ideas Through Titan New Venture Challenge, Jeffery Woodard

News and Events (Discontinued Series)

No abstract provided.

On The Benefits Of Directness In Virtual Characters For Motivational Interviews, Michael O'Mahony, Cathy Ennis, Robert Ross

Conference papers

Understanding the factors influencing successful engagement with Embodied Conversational Agents (ECAs) remains a significant challenge. This understanding could be used to personalise agents to users to improve interactions. Some studies have shown that simulating personalities in healthcare agents can improve effectiveness and engagement. However, it is not yet well understood how variations of agent personality can be leveraged to improve user engagement with Motivational Interviewing (MI) ECAs. Specifically how the balance between agent warmth and directness can be controlled in an MI agent to improve likeability and engagement. We conducted an online Wizard-of-Oz (WoZ) mediated study of two variants of …

Money Laundering Transactions Chronology Analysis Using Artificial Intelligence, Marwan Alawadhi

Theses

Money laundering is one of the most significant threats for the financial systems of the world, as it promotes other crimes and destabilizes the economy. This thesis presents an enhanced analysis of AI and ML on financial transaction data for the identification of patterns that relate to money laundering. It uses techniques like the Isolation Forest for the identification of outliers and clustering techniques like K-means and DBSCAN for identification of unusual transaction patterns across the four high risk countries that include United States, United Kingdom, Japan and Italy. The preprocessed dataset included different types of transactions like cross-border transactions, …

Libraries On The Front Lines: The Imperative For Disaster-Ready Information Professionals, Feili Tu-Keefner Ph.D.

Faculty Publications

Libraries, particularly local public libraries, have evolved into hubs for community-first services, extending beyond traditional roles. Library personnel are now expected to act as first responders and crisis leaders during times such as natural disasters. This report documents the critical crisis leadership qualifications required for library personnel, identified through comprehensive research from 2015 to 2023. Findings from these situation-specific case studies call attention to the community’s needs for library services during emergencies, underscoring the requirement for LIS education to include disaster management. Continuing education (CE) is also critical in preparing information professionals for these essential roles.

Wearable Surface Electromyography System To Predict Freeze Of Gait In Parkinson's Disease Patients., Anna Moore, Jinxing Li, Christopher H Contag, Luke J Currano, Connor O Pyles, David A Hinkle, Vivek Shinde Patil

Neuroscience Articles

Freezing of gait (FOG) is a disabling yet poorly understood paroxysmal gait disorder affecting the vast majority of patients with Parkinson's disease (PD) as they reach advanced stages of the disorder. Falling is one of the most disabling consequences of a FOG episode; it often results in injury and a future fear of falling, leading to diminished social engagement, a reduction in general fitness, loss of independence, and degradation of overall quality of life. Currently, there is no robust or reliable treatment against FOG in PD. In the absence of reliable and effective treatment for Parkinson's disease, alleviating the consequences …

Residential Metals Abatement Program Investigation Summary Report After The Bell Child Care Center, Environmental Resource Management (Erm)

Silver Bow Creek/Butte Area Superfund Site

No abstract provided.