Digital Commons Network^™

Multiphysics Simulation And Experimental Validation Of Phase Transformation And Hardness In Jominy End-Quenched Low-Alloy Steels, J. S. Alabi, E. Heidari, M. F. Buchely, K. Chandrashekhara, S. N. Lekakh, R. J. O'Malley, V. A. Athavale, A. Kumar

Materials Science and Engineering Faculty Research & Creative Works

High-volume industrial continuous hot-rolled steel heat treatment processes involve sophisticated multi-phase modeling. The performance of a given process can be optimized by coupling phase transformation kinetics with the cooling conditions of the process. This study develops a multiphysics model to simulate an intensive quenching process for steel, which is inherently transient and highly dependent on numerous parameters. The simulated object was a Jominy end-quenched specimen geometry using two commercial steels, AISI 4130 and AISI 4140, with the goal of transferring a verified methodology to the heat treatment process for industrial heavy-section products (bars, slabs). The simulation employs thermal, mechanical, and …

Effect Of Complex Alloying Elements On Oxide Scale Formation And Water-Jet Descaling Performance On Continuously Cast Low-Carbon Steels, Tochukwu P. Ojiako, Tsvetkov Dmitry, Mario Buchely, Haiming Wen, Simon N. Lekakh, Ronald J. O'Malley

Materials Science and Engineering Faculty Research & Creative Works

The formation and evolution of oxide scale in contact with mold flux during continuous casting, subsequent reheating, and hydraulic descaling are strongly governed by steel chemistry. To elucidate the effect of complex alloying elements (Si, Mn, and Cr), two industrially produced continuously cast low-carbon steel grades for manufacturing stamped parts (a base and alloyed steel grade) were investigated. The objective was to determine how alloying elements influence oxidation behavior, scale morphology, interfacial adhesion, and water-jet descaling efficiency. Continuously cast slab specimens were subjected to controlled thermal and atmospheric oxidation cycles simulating multistage industrial practice. Three initial surface conditions (industrial as-cast, …

Sadqn-Based Residual Energy-Aware Beamforming For Lora-Enabled Rf Energy Harvesting For Disaster-Tolerant Underground Mining Networks, Hilary Kelechi Anabi, Samuel Frimpong, Sanjay Madria

Mining Engineering Faculty Research & Creative Works

The end-to-end efficiency of radio-frequency (RF)-powered wireless communication networks (WPCNs) in post-disaster underground mine environments can be enhanced through adaptive beamforming. The primary challenges in such scenarios include (i) identifying the most energy-constrained nodes, i.e., nodes with the lowest residual energy to prevent the loss of tracking and localization functionality; (ii) avoiding reliance on the computationally intensive channel state information (CSI) acquisition process; and (iii) ensuring long-range RF wireless power transfer (LoRa-RFWPT). To address these issues, this paper introduces an adaptive and safety-aware deep reinforcement learning (DRL) framework for energy beamforming in LoRa-enabled underground disaster networks. Specifically, we develop a …

Utilizing Digital Twins To Model And Optimize Hydraulic Excavator Operator Performance Through Arena Simulation, Mateo Fernando Montenegro Defaz, Kwame Awuah-Offei

Mining Engineering Faculty Research & Creative Works

This study aims to provide a digital twin tool for mining and construction companies to evaluate the effect of operator behaviors on the truck-loading process, focusing on swing and bucket rotation. While equipment performance estimators are available, there are few tools to assess the influence of operators. The aim is to create a discrete event simulation (DES) model in Arena® to evaluate how variations in swing and bucket angles affect hydraulic excavator production rates. We validated the DES model using real-world data from a case study to assess the differences in behavior among four operators. Results showed that Operator 1 …

Stall Detection In Hydraulic Excavator Operations Using Heuristics And Machine Learning: A Case Study, Mateo Fernando Montenegro Defaz, Kwame Awuah-Offei, Yixiang Gao

Mining Engineering Faculty Research & Creative Works

This work aims to develop a reliable algorithm for stall detection during excavator digging by analyzing key operational variables such as velocity and angular displacements from machine monitoring data. The work develops and validates a heuristic algorithm to detect stalling events and trains a support vector machine classification algorithm to distinguish between "normal" digging cycles and cycles with stalling. This work is a novel attempt at using a classification algorithm to categorize digging cycles into normal and those with stalling events based on machine monitoring data alone. The developed classification algorithm achieved a sensitivity of 100%, indicating it correctly identified …

A Literature Review And Conceptual Framework For Sustainability In Open-Pit Mine Planning, Raymond Kudzawu-D'Pherdd, Kwame Awuah-Offei, Esteban Koberg De La Cruz, Marcos Goycoolea, Andrea Brickey, Alexandra M. Newman

Mining Engineering Faculty Research & Creative Works

This paper presents a comprehensive literature review and a conceptual framework for integrating environmental sustainability into strategic mine planning, focusing on open pits. Despite growing interest, easily discernible sustainability metrics remain elusive in early mine-planning stages, and are included as a post-processing step, if at all, rather than integrated a priori into a mine plan via, e.g., optimization. Through a literature review, we identify efforts regarding how environmental dimensions, such as emissions, water use, and land rehabilitation, are addressed across mine planning phases. We propose the Environmental Stewardship and Sustainability Framework for Mine Planning, which: (i) embeds sustainability into decision …

Analysis Of Pull-Out Tests For Resin-Grouted Rib Bolts, Khaled Mohamed, Yuting Xue, Dogukan Guner, Alper Kirmaci, Taghi Sherizadeh

Mining Engineering Faculty Research & Creative Works

Resin-grouted rib bolts serve as a crucial means of stabilizing spalling of coal ribs in underground coal mines. A comprehensive investigation into their efficacy was undertaken by a collaborative effort between the National Institute for Occupational Safety and Health (NIOSH) and Missouri University of Science and Technology (MST). This study involved pull-out tests of rib bolts in multiple locations, including six coal mines and the NIOSH research mine. A total of seventy-three (73) pull-out tests were conducted for rib bolts installed at different rotation speeds and a wide range of anchorage lengths, ranging from a short encapsulation length of 0.305 …

Sustmine: A Framework For Integrating Sustainable Development Dimensions Into Strategic Mine Planning, Hussam Altalhi, Kwame Awuah-Offei, Gabriel Nicolosi, Abdullah Al Moinee, Nasib Al Habib

Mining Engineering Faculty Research & Creative Works

Strategic mine planning involves optimizing resource extraction to achieve economic, environmental, and social objectives. However, only a few frameworks offer a unified approach that simultaneously employs systematic indicator selection and weightless trade-off evaluation. This study addresses these issues by proposing a comprehensive framework for integrating sustainability into strategic mine planning, named SustMine. SustMine introduces two key advancements: (1) a rigorous, systematic, criteria-based process for selecting site-specific sustainable development indicators (SDIs), and (2) a weightless evaluation strategy that utilizes Pareto front analysis to construct composite indices. This allows decision-makers to identify non-dominated (optimally balanced) alternatives without relying on arbitrary or subjective …

Elevated Temperature Flexure Behavior Of Continuous Carbon Fiber Reinforced Zrb2–Zrsi2 Ultrahigh Temperature Ceramic Matrix Composites, Jacob Stacy, Aaron Ginsparg, Jason Lonergan, Jeremy Watts, Gregory Hilmas

Materials Science and Engineering Faculty Research & Creative Works

Ultrahigh temperature ceramic matrix composites (UHTCMCs) were fabricated from unidirectional prepreg tapes consisting of a matrix of ZrB₂ with 5, 10, and 15 vol.% ZrSi₂ additions and continuous polyacrylonitrile carbon fibers and were densified at 1600°C in a hot press. The relative matrix densities ranged from 88% to 93% with interlayer spacings of ∼72 µm and fiber volume fractions between 30% and 36%. Phenolic resin additions were utilized to react with ZrSi₂ acting as a transient sintering aid to form ZrC and SiC phases. Elastic moduli of the UHTCMCs decreased with increasing temperature during 4-pt flexure testing. …

Quantitative Grain Structure And Texture Analysis Of Hot-Pressed Zrb2 Via 3d Ebsd, Randi Swanson, Michael Chapman, Yue Zhou, Ashley Hilmas, Lisa Rueschhoff, Michael Uchic, William Fahrenholtz, Scott J. Mccormack

Materials Science and Engineering Faculty Research & Creative Works

Understanding and controlling the grain structure of ZrB₂ is critical for optimizing its mechanical and thermal performance in high-temperature applications. Fully dense ZrB₂, densified by hot pressing at 2150˚C and 32 MPa, was analyzed in three dimensions using electron backscattered diffraction, electron and optical microscopy, and mechanical polishing serial sectioning. Grain size followed a gamma distribution, with extreme deviations observed only in the largest 0.1% of grains. Large grains exhibited plate-like morphologies, with the shortest-to-longest axis ratio converging to ∼0.4 as grain volume increased. This work revealed a crystallographically controlled growth mechanism orthogonal to [0001] that is …

Simulated Lunar Gravity Testing Of A Magnetic And Electrostatic System For Beneficiating Lunar Regolith, Blake A. Coffman, Gabriel Porter, Lindsay Manteufel, Mitchell Cottrell, Jeffrey D. Smith, David J. Bayless, William Shonberg, Frank D. Han, Fateme Rezaei, Kirby Runyon

Materials Science and Engineering Faculty Research & Creative Works

We present the design and testing of a lunar regolith beneficiation device that utilizes magnetic and electrostatic separation methods to concentrate desired minerals by removing unwanted material, such as the mineral anorthite, from bulk lunar regolith. The beneficiated materials would have value for downstream in-situ resource utilization (ISRU) processes such as metal extraction, oxygen extraction, and metal oxide additive manufacturing processes. The apparatus uses a dual-strength magnet system with N52 and N42 neodymium magnets to separate particles by magnetic susceptibility. The electrostatic separation system, which acts like a sieve, sorts the regolith simulant by particle size using a single-phase 50% …

The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …

Space Mining, Richard Painter

Articles

The Trump Administration and U.S. Congress are promoting new ventures to extract valuable minerals from outer space. This Article does not dismiss the idea out of hand, but explores reasons for caution, including practical problems with space mining, its environmental impact, the likelihood that the United States could violate international law, and the risk of armed conflict. These problems are exacerbated by financial conflicts of interest in our government with a handful of billionaires, who have a financial interest in space mining work. The promotion of their agenda could involve wasteful government spending on subsidies for private ventures, with a …

Large Language Scholarship, Alan Rozenshtein, Kevin Frazier

Articles

Generative AI isn’t just coming for the legal academy—the era of what we call “Large Language Scholarship” is already here. Law professors are using AI to write articles in weeks rather than months. Law reviews face an unprecedented deluge of AI-polished submissions. And the judges who increasingly lean on AI to help draft their own opinions will soon struggle to distinguish genuine insight from sophisticated imitation. Yet, existing scholarship offers only fragmented responses, trapped in misguided debates about plagiarism and disclosure while missing the full scope of the unfolding transformation.

This Article provides the first comprehensive analysis of how generative …

Microbial Collagenase Activity Is Linked To Oral–Gut Translocation In Advanced Chronic Liver Disease, Shen Jin, Aurelie Cenier, Daniela Wetzel, Bethlehem Arefaine, Mar Moreno-Gonzalez, Marilena Stamouli, Merianne Mohamad, Mariia Lupatsii, Emilio Ríos, Sunjae Lee, Ane Zamalloa, Shilpa Chokshi, Adil Mardinoglu, Saeed Shoaie, Naiara Beraza, Vishal C. Patel, Melanie Schirmer

Peninsula Medical School

Microbiome perturbations are associated with advanced chronic liver disease (ACLD), but how microorganisms contribute to disease mechanisms is unclear. Here we analysed metagenomes of paired saliva and faecal samples from an ACLD cohort of 86 individuals, plus 2 control groups of 52 healthy individuals and 14 patients with sepsis. We identified highly similar oral and gut bacterial strains, including Veillonella and Streptococcus spp., which increased in absolute abundance in the gut of patients with ACLD compared with controls. These microbial translocators uniquely share a prtC gene encoding a collagenase-like proteinase, and its faecal abundance was a robust ACLD biomarker (area …

Quantifying The Response Of Bankfull Channel Width To Active Faulting In The Qianhe Graben On The Southwest Margin Of Ordos Block, China, Zhiheng Liu, Sarah Boulton, Suiping Zhou, Jianhua Guo, Tingting Wu, Wenjie Zhang, Ling Han

School of Geography, Earth and Environmental Sciences

River longitudinal profiles have been widely used to quantify the transient landscape response to active faulting, but the fluvial cross-section is often ignored, yet width can also reveal river incision and tectonic activity. Channel width responds to tectonic forcing through flow concentration effects resulting in channel narrowing where vertical incision dominates during uplift acceleration. Here we employ a novel bankfull channel width extraction method using Landsat and ZY-3 satellite images, and SRTM DEM data to evaluate the cross-section landscape response to active faulting in the Qianhe Graben of southwest Ordos, China. Although some areas are difficult to access (e.g., thick …

Investigating The Impact Of Carboxylated Polystyrene Nanoplastics In The Liver Using Cell Lines And Precision-Cut Liver Slices, Namrata Pandey, Paula Boeira, Nathaniel J. Clark, Eleanor T. Walker, Somaiah Aroori, Jemimah Denson, Richard C. Thompson, Matthew E. Cramp, Shilpa Chokshi, Ashwin Dhanda

Peninsula Medical School

Background and Aims: Increasing reports of plastic accumulation in human tissue have raised concerns about potential adverse health outcomes. Evidence of negative effects of nanoplastics is heterogeneous and provides limited insights into the underlying pathogenic toxicity mechanisms in humans. Methods: In the present study, carboxylate-modified fluorescently labelled polystyrene nanoparticles (PS NPs) were used to investigate uptake and cytotoxicity in three different hepatic models of varying complexity, including HepG2 cells, IHH cells, and human precision-cut liver slices (hPCLS). Results: The results show model- and dose-dependent effects on hepatocytes. 74.2% ± 13.4% of the IHH cells showed PS NPs uptake at 0.1 …

Designing A Mobile App For Post Traumatic Stress Disorder: Insights From Lived Experience And Clinical Practice, Rohit Shankar, Richard Laugharne, Michael Loizou, Marius Varga, Sivia Lin, Bojana Daw Srdanovic, Roger Farrell

Peninsula Medical School

Post-traumatic stress disorder (PTSD) is a disabling anxiety disorder precipitated by severe trauma. Many people with this condition have little access to clinical interventions, especially in low-middle-income countries. For the development of any digital health intervention, it is vital to know the opinions of PLE and clinicians to guide the developers. We conducted two focus groups, one with clinicians (n = 5) and one with people with lived experience (PLE) (n = 11), to gain knowledge of their views on the development of a PTSD App. Transcripts of both focus groups were coded and thematically analysed. The key themes that …

Small-Molecule Therapies Targeting Tumor-Associated Macrophages In Glioma: Mechanisms And Potential, Hua Wang, Heng Luo, Haijian Zhong, Amy Ockleton, Feng Jiang, Renhui Yi, Shaochun Yang, Ming Li

Peninsula Medical School

Glioblastoma, a highly prevalent and aggressive primary brain tumor, is marked by poor prognosis due to the blood-brain barrier and chemoresistance, which limit conventional pharmacotherapy. Recent research has pivoted toward targeting the tumor microenvironment, where tumor-associated macrophages (TAMs) drive gliomagenesis and malignant progression through immunosuppressive signaling. Small-molecule agents targeting TAMs have emerged as promising therapeutics, capable of reprogramming macrophage polarization, modulating immune cell dynamics, and suppressing glioma growth. This review explores the mechanistic roles of TAMs in glioma and evaluates how small-molecule compounds exert antitumor effects via TAM modulation. These insights lay a foundation for developing next-generation TAM-targeted therapies, offering …

Others’ Requests May Dampen The Desire To Do Good: The Effect Of Requests On Children's Prosocial Motivation Across Five Cultures., Anneliese Skrobanek, Patricia Kanngiesser, Jahnavi Sunderarajan, Jorge David Mantilla Salgado, Saiwa Sisa Quimbo Yacelga, Shoji Itakura, Marie M. Morita, Masanori Yamaguchi, Nadia Chernyak, Lucy M. Stowe, Joscha Kärtner

School of Psychology

There exists cultural variation in how people react to prosocial obligations, but we still know little about when these differences emerge in development and how they can be explained. We investigated this in a study with 6- to 11-year-old children (N = 686) in five cultural contexts. Children listened to scenarios about spontaneous and requested (within-subjects) helping and sharing. They rated requested scenarios as less desirable and less satisfying, but there was significant cross-cultural variation in the magnitude of this effect, which was mostly stable with age. We also measured children's sense of individual agency and internalization of prosocial norms …

Upconversion Photoluminescence In Wsse Alloy Monolayer Under Uniaxial Tensile Strain, Shrawan Roy, Jie Gao, Xiaodong Yang

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The optical responses of monolayer transition metal dichalcogenides (1L-TMDs) can be tuned effectively by using mechanical strain. In this work, the tuning of upconversion photoluminescence (UPL) emission in 1L-WSSe alloy by applying uniaxial tensile strain is investigated. When the uniaxial tensile strain is changed from 0 % to 1.02 %, the peak position of UPL emission has a redshift of around 25.6 nm, and the UPL intensity goes up with an exponential function of the applied strain as the upconversion energy difference is varied from −197 meV to −131 meV. The sublinear power dependence for UPL emission in 1L-WSSe alloy …

A Combined Tomographic Particle Image Velocimetry And Numerical Simulation Approach For Supersonic Wind Tunnel Calibration, Joshua Gary, Josiah Mcdermott, Kyle Worden, Serhat Hosder, Davide Viganò

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Supersonic wind tunnels remain essential tools for high-speed aerodynamics research, yet the characterization of their free-stream conditions remains technically challenging and lacks standardized criteria for defining "good" flow quality. While traditional calibration methods rely on intrusive probes, recent advances in optical diagnostics offer new opportunities for non-intrusive characterization. In this work, we demonstrate a novel use of Tomographic Particle Image Velocimetry (Tomo-PIV), combined with numerical simulations, as a methodology for supersonic wind tunnel calibration. The approach is applied to the recently upgraded Missouri S&T Supersonic Wind Tunnel, where Tomo-PIV measurements reveal uniform flow with low angularity and low turbulent noise …

Physics-Constrained Generative Adversarial Networks For Dimensionality Reduction In Optimization, Samuel Sisk, Xiaosong Du

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electric vertical takeoff and landing (eVTOL) aircraft make a unique form of urban air mobility due to their low noise, zero emission, and precision control. To maximize efficiency, high-fidelity simulation-based multidisciplinary design optimization discovers the optimal balance among subsystems within an eVTOL. However, conventional multidisciplinary design optimization is computationally intensive due to excessive high-fidelity model evaluations. Moreover, complex nonlinear constraints deteriorate optimization efficiency and convergence. While surrogate models enable efficient design optimization, surrogate modeling suffers in large-scale applications and surrogate-based optimization still has to deal with nonlinear constraints. To address these challenges, the authors' previous work proposed physics-constrained generative adversarial …

Tomo-Piv Study Of Baseline Flow Structures Behind A Strut Injector, Josiah Mcdermott, Connor Bell, Davide Viganò

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Stabilizing combustion in scramjet engines is a formidable challenge due to the small-time scales afforded for air-fuel mixing. Numerous studies in this area have demonstrated the potential of strut-style platforms for fuel injection and mixing enhancement, which remains an active area of research. In the Aerodynamics Research Laboratory at Missouri S&T, a strut-style injector system has recently been installed. In this study, we characterize the baseline flow structures behind this platform absent fuel injection. The wake generated by a strut itself has an appreciable impact on the resulting air-fuel mixing, which motivates its characterization. In future studies, this characterization will …

Optimal Takeoff Trajectory Prediction Of Electric Drones Based On A Fully Automated Optimal Experimental Design Method, Jiachen Wang, Dheeraj Paramkusham, Xiaosong Du

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electric vertical takeoff and landing (eVTOL) aircraft is attracting great interest as a viable solution to promote urban aerial mobility with promising flexibility as well as emission reductions. However, the low specific energy of the current battery is still a strong constraint on the range and endurance of eVTOL flights, especially considering the significant power demands during the takeoff process. Engineering design optimization permits promising solutions for the minimum takeoff energy consumption but can be computationally intensive due to iteratively evaluating simulation models. Surrogate-based design optimization is efficient but still relies on optimization iterations which prohibit real-time decision-making. To fill …

Impact Of Dispersed Crystalline Domains On Lithium-Ion Conductivity In Amorphous Li2.99ba0.005ocl Electrolytes, Emmanuel Olugbade, Junquan Ou, Leon Shaw, Jonghyun Park

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Solid-state electrolytes promise safer, high-energy batteries, yet ionic transport is limited by structural heterogeneity and interfacial resistance. We combine hydrothermal synthesis and molecular dynamics (MD) to determine how dispersed crystallinity and interfacial orientation govern lithium-ion conduction in barium-doped anti-perovskite Li_2.99Ba_0.005OCl. Structural and thermal analyses identify a largely amorphous matrix with embedded nano crystallites, and MD captures the same short-range order and dispersion seen experimentally. Electrochemical impedance spectroscopy separates high amorphous-phase conductivity from a pellet-scale response dominated by interfacial limitations, consistent with direct-current polarization. Cyclic voltammetry indicates a broad electrochemical stability window. We quantify transport in crystalline …

Distributed Vibration Sensing For Identification Of Loose Connectors In Coaxial Data Transmission Lines, Saidanvar Esanjonovich Valiev, Anthony C. Okafor, Jeremiah J. Rittenhouse, Jie Huang, Daniel S. Stutts

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This study investigates the effect of vibration-induced loose connections on signal reflection (S11) for loose connection identification in aerospace coaxial cables using distributed sensing approach, which is effective in filtering the noise and identifying minor discontinuities. In this approach, a sliding gated window is applied to S11 signal, a fast Fourier transform is performed over the gated windows, cross-correlation is computed between the baseline and vibration-affected signals, and the standard deviation is mapped along the cable length. Sinewave signals from 9 kHz to 5 GHz were swept through cables with vibrating connectors under three conditions: fully tightened, loosened by 180°, …

Multiphysics Modeling Of Melt Pool Dynamics And Powder Bed Stability In Lpbf Of Inconel 718 For A Circular Cavity, Nayan Pundhir, Oluwapelumi O. Adejumo, Kumbla Chandrashekhara, Joseph W. Newkirk, Heath Misak, Cesar Ortiz Rios

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laser powder bed fusion (LPBF) is a metal additive manufacturing process in which a concentrated laser beam selectively melts successive powder layers to fabricate components. Final part quality is highly sensitive to process parameters such as hatch spacing, powder bed density, laser power, and scanning speed. In this study, a computational fluid dynamics model employing discrete element method has been developed in FLOW-3D to simulate LPBF of Inconel 718. The modeled powder bed incorporates particle size distribution data obtained from scanning electron microscopy and is evaluated for single-layer, single-track deposition over a circular cavity. The model captured melt pool dynamics …

Atomized Oxidative Polymerization As A 3d Printing Platform For Binder-Free, Bulk Conductive Polymer Architectures, Tazdik Patwary Plateau, Hiep Pham, Jonghyun Park

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Translating the ultrahigh intrinsic conductivity of conjugated polymers into bulk 3D architectures remains a formidable challenge due to the fundamental dichotomy between rheological printability and electronic purity. Existing strategies necessitate a compromise: solution-processing requires insulating binders that degrade charge transport, while binder-free vapor-phase polymerization (VPP) is kinetically confined to surface-limited thin films by diffusion constraints. Here, we introduce atomized oxidative polymerization (AOP), a manufacturing paradigm that overcomes these kinetic barriers via active, layer-by-layer monomer atomization. This approach ensures stoichiometric reaction conditions throughout the printed volume, driving a structural transition toward highly conductive quinoid-dominant chains with enhanced π-π stacking. The resulting …

Performance Evaluation Of Thick Carbon Fiber-Reinforced Laminates Manufactured Using Six-Magnetron Microwave System, Nayan Pundhir, Sourav Bolar, Kumbla Chandrashekhara, Kristen Donnell, Jim Lua, Kalyan Shrestha, Rui Li

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Microwave curing is a fast, energy-efficient, and a viable alternative to conventional thermal curing processes. It has been widely adopted for processing carbon fiber-reinforced polymer composites because the high electrical conductivity of carbon fibers enables strong microwave coupling. In this study, IM7/Cycom 5320-1 unidirectional prepreg has been used to fabricate 64-layer laminated composites. Symmetric cross-ply ([0°/90°]16S) and a quasi-isotropic ([45°/90°/−45°/0°]8S) layup have been investigated. A custom-built six-magnetron microwave applicator and an autoclave were employed to manufacture the composite panels. Degree of cure of the manufactured laminates was evaluated via differential scanning calorimetry. Interfacial bonding and porosity of the microwave-cured laminates …