Digital Commons Network^™

Optimized Gadolinium-Do3a Loading In Raft-Polymerized Copolymers For Superior Mr Imaging Of Aging Blood-Brain Barrier, Hunter A. Miller, Aaron Priester, Evan T. Curtis, Krista Hilmas, Ashleigh Abbott, Forrest M. Kievit, Anthony J. Convertine

Materials Science and Engineering Faculty Research & Creative Works

The development of gadolinium-based contrast agents (GBCAs) has been pivotal in advancing magnetic resonance imaging (MRI), offering enhanced soft tissue contrast without ionizing radiation exposure. Despite their widespread clinical use, the need for improved GBCAs has led to innovations in ligand chemistry and polymer science. We report a novel approach using methacrylate-functionalized DO3A ligands to synthesize a series of copolymers through direct reversible addition-fragmentation chain transfer (RAFT) polymerization. This technique enables precise control over the gadolinium content within the polymers, circumventing the need for subsequent conjugation and purification steps, and facilitates the addition of other components such as targeting ligands. …

Experimental Investigation Of A Viscoelastic Liner To Reduce Under Helmet Overpressures And Shock Wave Reflections, Cody J.H. Thomas, Fatih Dogan, Catherine E. Johnson

Materials Science and Engineering Faculty Research & Creative Works

Introduction: Shock wave overpressure exposures can result in blast-induced traumatic brain injury (bTBI) in warfighters. Although combat helmets provide protection against blunt impacts, the protection against blast waves is limited due to the observed high overpressures occurring underneath the helmet. One route to enhance these helmets is by incorporating viscoelastic materials into the helmet designs, reducing pressures imposed on the head. This study aims to further investigate this mitigation technique against under-helmet overpressures by adding a viscoelastic liner to the inside of a combat helmet. Methods: The liner's effectiveness was evaluated by exposing it to free-field blasts of Composition C-4 …

Prompt, Accurate, And Noncontact Material Identification Using A Single Microwave Sensor With Machine Learning Analysis, Chen Zhu, Osamah Alsalman, Jie Huang

Electrical and Computer Engineering Faculty Research & Creative Works

In This Article, a Novel Approach to Microwave Sensors is Proposed and Demonstrated that Allows for Prompt, Accurate, and Noncontact Material Identification Even with Arbitrary Lift-Off Distances between the Sensor and the Material under Test (MUT). a Multilayer Perceptron (MLP) is Trained to Directly Learn the Relation of the Measured Reflection Spectra of a Homemade Open-Ended Coaxial Cable Resonator Probe with Respect to Different MUTs and Then Achieve One-To-One Mapping between a Measured Spectrum and the MUT. as a Proof-Of-Concept Demonstration, the Performance of the MLP Model is Tested using Easily Accessible Materials, Including Wood, Glass, Water, and Metal. Reflection …

Statistical Eye Diagrams For High-Speed Interconnects Of Packages: A Review, Junyong Park, Donghyun Kim

Electrical and Computer Engineering Faculty Research & Creative Works

An eye diagram, a critical metric in signal integrity analysis for high-speed interconnects such as packages, interposer, and printed circuit boards (PCBs), is generated by superposition of the received waveform. Obtaining an eye diagram is time-consuming, thus signal integrity analysis is inefficient. This article reviews that have been proposed to overcome this limitation. The statistical eye diagram provides a probability distribution depending on a sampling time and voltage, therefore it can be expanded to other metrics, such as the bit-error rate and shmoo plot. This article introduces previous research on statistical eye diagrams applied to complementary metal-oxide-semiconductors (CMOSs), noise, and …

A Segmentation Approach For Predicting Plane Wave Coupling To Pcb Structures, Shengxuan Xia, James Hunter, Aaron Harmon, Ahmed M. Hassan, Victor Khilkevich, Daryl G. Beetner

Electrical and Computer Engineering Faculty Research & Creative Works

Evaluating the far-field radio frequency (RF) susceptibility of electronic devices often depends on extensive testing or full wave simulations. These methods are effective when complete system information is available but require substantial time and resources to evaluate a large number of variations in system configurations, where trace routings, integrated circuit (IC) package styles, trace terminations, arrival angle, and polarization of incoming wave, etc., are varied from one configuration to another. The goal of the following article is to develop simulation techniques for studying the statistical characteristics of coupling to typical printed circuit board (PCB) structures. Simulation time can be reduced …

Meta-Icvi: Ensemble Validity Metrics For Concise Labeling Of Correct, Under- Or Over-Partitioning In Streaming Clustering, Niklas M. Melton, Sasha Petrenko, Donald C. Wunsch

Electrical and Computer Engineering Faculty Research & Creative Works

Understanding the performance and validity of clustering algorithms is both challenging and crucial, particularly when clustering must be done online. Until recently, most validation methods have relied on batch calculation and have required considerable human expertise in their interpretation. Improving real-time performance and interpretability of cluster validation, therefore, continues to be an important theme in unsupervised learning. Building upon previous work on incremental cluster validity indices (iCVIs), this paper introduces the Meta- iCVI as a tool for explainable and concise labeling of partition quality in online clustering. Leveraging a time-series classifier and data-fusion techniques, the Meta- iCVI combines the outputs …

Equivalent Source Investigation For Pcb Vibration Excited By A Multilayer Ceramic Capacitor, Yifan Ding, Ming Feng Xue, Jianmin Zhang, Xin Hua, Benjamin Leung, Eric A. Macintosh, Chulsoon Hwang

Electrical and Computer Engineering Faculty Research & Creative Works

Multilayer ceramic capacitors (MLCCs) are commonly used on printed circuit board (PCB) power distribution networks (PDN) for decoupling purposes. However, an MLCC can act as a source to excite PCB vibrations due to noise ripples on the power rail. In this letter, four types of equivalent source configurations are studied and compared to represent the excitation of an MLCC on a PCB driven by power rail noise. The corresponding source values are extracted at test-vehicle PCB resonance frequencies. The investigation of the four equivalent source types involves a comparison between simulated and measured PCB vibration velocity responses triggered by MLCC …

A Compact And High-Efficiency Antenna Design For Tire Pressure Monitoring System Applications, Lei Deng, Lidong Chi, Francesco De Paulis, Yihong Qi

Electrical and Computer Engineering Faculty Research & Creative Works

This article proposes a novel design for a compact antenna that exhibits high efficiency and low interference and is suitable for tire pressure monitoring systems (TPMSs) based on Bluetooth communication interface at 2.4 GHz. Tires constitute a dissipative environment, where the efficiency of the TPMS is affected by both antenna losses and losses from the tire parts, both conductive and dielectric. This article conducts an analysis and simulation of the electromagnetic (EM) environment of the tire and identifies the optimal polarization and placement position for the TPMS antenna to minimize resonance losses of EM waves within the tire, enhance lateral …

A Wavegan Approach For Mmwave-Based Fanet Topology Optimization, Enas Odat, Hakim Ghazzai, Ahmad Alsharoa

Electrical and Computer Engineering Faculty Research & Creative Works

The integration of dynamic Flying Ad hoc Networks (FANETs) and millimeter Wave (mmWave) technology can offer a promising solution for numerous data-intensive applications, as it enables the establishment of a robust flying infrastructure with significant data transmission capabilities. However, to enable effective mmWave communication within this dynamic network, it is essential to precisely align the steerable antennas mounted on Unmanned Aerial Vehicles (UAVs) with their corresponding peer units. Therefore, it is important to design a novel approach that can quickly determine an optimized alignment and network topology. In this paper, we propose a Generative Adversarial Network (GAN)-based approach, called WaveGAN, …

Effect Of Bioactive Borate Glass On Printability And Physical Properties Of Hydrogels, Fateme Fayyazbakhsh, Mehedi H. Tusar, Yue-Wern Huang, Ming C. Leu

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Hydrogels are a key component in bioinks and biomaterial inks for bioprinting due to their biocompatibility and printability at room temperature. The research described in the present paper contributes to the advancement of bioprinting by studying the effect of bioactive borate glass (BBG) incorporated into hydrogels on printability and physical properties. In this study, we fabricated 3D-printed hydrogel scaffolds using gelatin and alginate hydrogel mixture incorporated with various amounts of BBG, a bio ceramic rich in therapeutic ions including boron, calcium, copper, and zinc. We investigated the effect of incorporating BBG on the density, viscosity, physical interactions, chemical structure, and …

An Evaluation Of Methods For Assessing Robot Kinematic Model Accuracy In The Presence Of Noise, Mitchell R. Woodside, Patrick Bazzoli, Philip A. Olubodun, J. Adam Nisbett, Guixiu Qiao, Douglas A. Bristow

Mechanical and Aerospace Engineering Faculty Research & Creative Works

While there are many works developing methods for modeling and calibrating robot kinematics, assessing the accuracy of those models has received little attention. However, accuracy assessment is critically important for applications where the robot must operate with absolute accuracy over a large region of workspace, such as in robotic machining. When the model of such a system is well calibrated, the remaining deterministic error can be quite complex, owing to complicated gearing errors, deformations, and quasi-static thermal changes. Locating the largest deterministic error requires an exploration over the workspace, but assessing the largest error is complicated by repeatability error and …

Development Of Digital Twin For Fdm Printer With Preventive Cyber-Attack And Control Algorithms, Md Hazrat Ali, Asad Malik, Nursultan Jyeniskhan, Muhammad Arif Mahmood, Essam Shehab, Frank Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

This paper presents a developed model of a Digital Twin (DT) for a fused deposition modeling (FDM) printer, real-time defect detection, and proposed frameworks for preventing cyber-attacks in real-time. It also highlights a model predictive control (MPC) algorithm for controlling the material feed based on a real-time feedback system. The system is designed and developed based on DT, and MPC with integrated machine learning (ML) algorithms to establish real-time process control and enhance the safety and reliability of the physical plant. ML algorithm is used for anomaly detection based on the convolutional neural network (CNN) model. The developed system can …

Hyper-Thick Electrodes For Lithium-Ion Batteries Enabled By Micro-Electric-Field Process, Tazdik Patwary Plateau, Gracie Boyer, Jonghyun Park

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Increasing electrode thickness is a key strategy to boost energy density in lithium-ion batteries (LIBs), which is essential for electric vehicles and energy storage applications. However, thick electrodes face significant challenges, including poor ion transport, long diffusion paths, and mechanical instability, all of which degrade battery performance. to overcome these barriers, a novel micro-electric-field (μ-EF) process is introduced that enhances particle alignment during fabrication with reduced distance between anode and cathode. This process produces hyper-thick (≈700 µm) electrodes with low tortuosity and improved ion diffusion. the μ-EF electrodes achieve high areal capacities (≈8 mAh cm−2), while maintaining power density and …

A Model For Corona Streamer Propagation On Glass During An Air Discharge, Zhekun Peng, Jianchi Zhou, Darryl Kostka, David Pommerenke, Daryl G. Beetner

Electrical and Computer Engineering Faculty Research & Creative Works

Corona discharge to a glass surface is challenging to model due to a poorly understood air and surface ionization process. A modeling methodology based on the transmission line modeling (TLM) approach is proposed to simulate the streamer propagation process. The time-changing corona streamer resistance is estimated using the Rompe and Weizel spark model. The streamer is represented using small segments consisting of the arc resistance, per unit length (PUL) capacitance of the streamer, PUL inductance, a switch representing streamer formation, and a surface discharge gap voltage representing the voltage drop caused by ions within the streamer length. The propagation of …

Coupling-Informed Data-Driven Scheme For Joint Angle And Frequency Estimation In Uniform Linear Array With Mutual Coupling Present, Yanming Zhang, Wenchao Xu, A. Long Jin, Min Li, Peifeng Ma, Lijun Jiang, Steven Gao

Electrical and Computer Engineering Faculty Research & Creative Works

This paper proposes a novel coupling-informed data-driven algorithm tailored for the concurrent estimation of frequency and angle within a uniform linear array (ULA), while addressing the complicating influence of mutual coupling. Leveraging the hybrid dynamic mode decomposition (DMD) methodology, termed as averaged DMD, we incorporate moving average techniques to achieve effective denoising. The averaged DMD further decomposes the received signal into eigenvalues and corresponding eigenvectors. The frequency information is derived from the eigenvalues and the corresponding eigenvectors represent the steering vectors of sources. Subsequently, mutual coupling is informed into the calibration of the steering vector for each source. Specifically, the …

Design Of The Tm010 Mode Cylindrical Cavity Resonator For Pcb Dielectric Characterization, Reza Asadi, Chaofeng Li, Seyedmehdi Mousavi, Seyed Moastafa Mousavi, Reza Vahdani, Xiaoning Ye, Donghyun Kim

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents the study of the TM₀₁₀ mode cylindrical resonator, which can be used for printed circuit board (PCB) material properties extraction, e.g., the dielectric constant (Dk) and the loss tangent (Df) extraction. The theoretical formulas of the resonance frequency and Q-factor of the resonator are presented. In real measurement, the TM₀₁₀ mode cylindrical cavity resonator needs to be excited by the probe. The study emphasizes the impact of probe orientation, location, and field distribution on the accuracy of material property extraction. The relationship between cavity dimensions and resonance frequency is explored, highlighting the influence of cavity …

A Tensor-Based Data-Driven Approach For Multidimensional Harmonic Retrieval And Its Application For Mimo Channel Sounding., Yanming Zhang, Wenchao Xu, A. Long Jin, Min Li, Ping Yuan, Lijun Jiang, Steven Gao

Electrical and Computer Engineering Faculty Research & Creative Works

In wireless channel sounding, accurately estimating multiple parameters within a multipath signal, such as azimuth, elevation, Doppler shift, and delay, necessitates addressing the challenges posed by the multidimensional harmonic retrieval (MHR) problem. To overcome these complexities, we propose a framework based on high-order dynamic mode decomposition (HODMD) that designed for robustly estimating frequencies of interest from high-dimensional sinusoidal signals, particularly in additive white Gaussian noise conditions. The HODMD approach, a hybrid algorithm amalgamating high-order singular value decomposition (HOSVD) and dynamic mode decomposition (DMD), operates by initially decomposing observed tensorial data into a core tensor and R mode matrices through HOSVD. …

Modeling Of Power Distrubition Network (Pdn) Noise Coupling Induced Clock Phase Noise, Zhekun Peng, Junyong Park, Chaofeng Li, Joey Stecher, Srinivas Venkataraman, Xu Wang, Granthana Rangaswamy, Donghyun Kim

Electrical and Computer Engineering Faculty Research & Creative Works

Phase noise analysis is important to clock design. Noise sources of spurs shown on the phase noise result are challenging to find out due to the unknown source locations and coupling mechanisms. Noise from power distribution network (PDN) is one of the most troublesome sources. A behavioral modeling methodology is proposed to simulate the clock phase noise induced by PDN noise coupling for two different mechanisms: PDN-to-clock additive coupling and PDN-to-PDN up-conversion modulation. The thermal noise and 1/f flicker noise are simplified to provide a straightforward view of spur level. The model can be applied to both single-ended clock and …

Ai Trustworthy: Ethical Challenges And Strategies, Jian Liu, Iwan Sandjaja, Donald C. Wunsch

Electrical and Computer Engineering Faculty Research & Creative Works

This paper explores the pivotal role of trust in the widespread application of Artificial Intelligence (AI) across various domains. We review AI applications in sectors like energy, healthcare, and autonomous vehicles and discuss the crisis of human trust they face. This paper introduces a novel framework that delineates the relationship between AI transparency and user trust, highlighting specific industry applications. Through a systematic review of recent literature, we first delve into factors such as emotional response, acceptance, transparency, accuracy, and interpretability that shape human trust in AI. We then underscore the necessity of ethical AI practices and highlight the importance …

Empowering Urban Traffic Management: Elevated 3d Lidar For Data Collection And Advanced Object Detection Analysis, Nawfal Guefrachi, Hakim Ghazzai, Ahmad Alsharoa

Electrical and Computer Engineering Faculty Research & Creative Works

The 3D object detection capabilities in urban environments have been enormously improved by recent developments in Light Detection and Range (LiDAR) technology. This paper presents a novel framework that transforms the detection and analysis of 3D objects in traffic scenarios by utilizing the power of elevated LiDAR sensors. We are presenting our methodology's remarkable capacity to collect complex 3D point cloud data, which allows us to accurately and in detail capture the dynamics of urban traffic. Due to the limitation in obtaining real-world traffic datasets, we utilize the simulator to generate 3D point cloud for specific scenarios. To support our …

Impact Of Ai On The Hri Dynamic In Search And Rescue Operations Using Uav Swarms, Jordan Morrow, Maciej Jan Zawodniok, Anhar Sami Mohammed

Electrical and Computer Engineering Faculty Research & Creative Works

Artificial intelligence (AI) offers significant benefits in search and rescue applications by enhancing the efficiency and effectiveness of the search. However, an over-reliance on AI can hinder the operation due to biases embedded in the underlying algorithms. This partiality, if left un-monitored, can pose a risk to the safety of those in need of disaster relief. Typically manifests into inaccuracies in the decision-making processes and if not carefully monitored can cause larger issues. This paper extends the knowledge presented in a previous work, which presents the design and modeling of search and rescue operations using unmanned aerial vehicle (UAV) swarms. …

New Testing Capabilities Of The Missouri University Of Science And Technology Supersonic Wind Tunnel, Joshua Gary, Davide Viganò

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The development of non-intrusive, laser-based diagnostic techniques has significantly enhanced supersonic experimental aerodynamics, enabling the measurement of many parameters in complex flow fields. Among these techniques, Tomographic Particle Image Velocimetry, capable of measuring 3 components of velocity in 3-dimensional volumes, is now available at the Aerodynamics Research Laboratory of the Missouri University of Science and Technology. To integrate this new system into the university's supersonic wind tunnel, a redesigned nozzle, test section, and diffuser have been implemented. The upgraded modular test section features 4 large ports which can be configured with windows for optical diagnostics or lead plates for model …

Optimal Tilt-Wing Evtol Takeoff Trajectory Prediction Using Regression Generative Adversarial Networks, Shuan Tai Yeh, Xiaosong Du

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electric vertical takeoff and landing (eVTOL) aircraft have attracted tremendous attention nowadays due to their flexible maneuverability, precise control, cost efficiency, and low noise. The optimal takeoff trajectory design is a key component of cost-effective and passenger-friendly eVTOL systems. However, conventional design optimization is typically computationally prohibitive due to the adoption of high-fidelity simulation models in an iterative manner. Machine learning (ML) allows rapid decision making; however, new ML surrogate modeling architectures and strategies are still desired to address large-scale problems. Therefore, we showcase a novel regression generative adversarial network (regGAN) surrogate for fast interactive optimal takeoff trajectory predictions of …

A Secure And Robust Knowledge Transfer Framework Via Stratified-Causality Distribution Adjustment In Intelligent Collaborative Services, Ju Jia, Siqi Ma, Lina Wang, Yang Liu, Robert H. Deng

Research Collection School Of Computing and Information Systems

The rapid development of device-edge-cloud collaborative computing techniques has actively contributed to the popularization and application of intelligent service models. The intensity of knowledge transfer plays a vital role in enhancing the performance of intelligent services. However, the existing knowledge transfer methods are mainly implemented through data fine-tuning and model distillation, which may cause the leakage of data privacy or model copyright in intelligent collaborative systems. To address this issue, we propose a secure and robust knowledge transfer framework through stratified-causality distribution adjustment (SCDA) for device-edge-cloud collaborative services. Specifically, a simple yet effective density-based estimation is first employed to obtain …

Big Code Search: A Bibliography, Kisub Kim, Sankalp Ghatpande, Dongsun Kim, Xin Zhou, Kui Liu, Tegawende F. Bissyande, Jacques Klein, Traon Yves Le

Research Collection School Of Computing and Information Systems

Code search is an essential task in software development. Developers often search the internet and other code databases for necessary source code snippets to ease the development efforts. Code search techniques also help learn programming as novice programmers or students can quickly retrieve (hopefully good) examples already used in actual software projects. Given the recurrence of the code search activity in software development, there is an increasing interest in the research community. To improve the code search experience, the research community suggests many code search tools and techniques. These tools and techniques leverage several different ideas and claim a better …

Tracking People Across Ultra Populated Indoor Spaces By Matching Unreliable Wi-Fi Signals With Disconnected Video Feeds, Quang Hai Truong, Dheryta Jaisinghani, Shubham Jain, Arunesh Sinha, Jeong Gil Ko, Rajesh Krishna Balan

Research Collection School Of Computing and Information Systems

Tracking in dense indoor environments where several thousands of people move around is an extremely challenging problem. In this paper, we present a system — DenseTrack for tracking people in such environments. DenseTrack leverages data from the sensing modalities that are already present in these environments — Wi-Fi (from enterprise network deployments) and Video (from surveillance cameras). We combine Wi-Fi information with video data to overcome the individual errors induced by these modalities. More precisely, the locations derived from video are used to overcome the localization errors inherent in using Wi-Fi signals where precise Wi-Fi MAC IDs are used to …

Glance To Count: Learning To Rank With Anchors For Weakly-Supervised Crowd Counting, Zheng Xiong, Liangyu Chai, Wenxi Liu, Yongtuo Liu, Sucheng Ren, Shengfeng He

Research Collection School Of Computing and Information Systems

Crowd image is arguably one of the most laborious data to annotate. In this paper, we devote to reduce the massive demand of densely labeled crowd data, and propose a novel weakly-supervised setting, in which we leverage the binary ranking of two images with highcontrast crowd counts as training guidance. To enable training under this new setting, we convert the crowd count regression problem to a ranking potential prediction problem. In particular, we tailor a Siamese Ranking Network that predicts the potential scores of two images indicating the ordering of the counts. Hence, the ultimate goal is to assign appropriate …

Nasoalveolar Molding: A Rise In Early Management Of Newborn Patient With Cleft Lip And Palate, Reeya Agrawal, Pallavi Daigavane, Amit Reche

International Arab Journal of Dentistry

Orofacial clefts are one of the most frequent congenital oral and maxillofacial abnormalities. When these babies are roughly three months old, lip rebuilding, also known as cheiloplasty, is a critical concern. In several cleft facilities, To improve the treatment success, presurgical Nasoalveolar Molding (NAM) has been included in the therapy protocol. In patients with cleft lip and palate, this technique is routinely used to bring the alveolar segments into normal alignment and improve nasal symmetry. In this article, the benefits of using this method as part of a treatment plan for infants with cleft lip and palate will be described. …

Clearspeech: Improving Voice Quality Of Earbuds Using Both In-Ear And Out-Ear Microphones, Dong Ma, Ting Dang, Ming Ding, Rajesh Krishna Balan

Research Collection School Of Computing and Information Systems

Wireless earbuds have been gaining increasing popularity and using them to make phone calls or issue voice commands requires the earbud microphones to pick up human speech. When the speaker is in a noisy environment, speech quality degrades significantly and requires speech enhancement (SE). In this paper, we present ClearSpeech, a novel deep-learningbased SE system designed for wireless earbuds. Specifically, by jointly using the earbud’s in-ear and out-ear microphones, we devised a suite of techniques to effectively fuse the two signals and enhance the magnitude and phase of the speech spectrogram. We built an earbud prototype to evaluate ClearSpeech under …

Diagnosis And Endodontic Treatment Of Odontogenic Cutaneous Sinus Tracts: A Report Of Two Cases, Mayada Jemâa, Marwenne Bouatay, Yesmine Neifar, Mohamed Bassem Khattech

International Arab Journal of Dentistry

Introduction: The odontogenic cutaneous sinus tract (OCST), caused by pulp necrosis, creates connections between pathological spaces and anatomical structures. Extraoral manifestations pose diagnostic challenges leading to inappropriate treatments such as multiple surgery and antibiotic therapies. Effective management requires the treatment of dental pathology through endodontic therapy or extraction. This paper presents two cases of OCST and emphasizes the importance of accurate diagnosis and successful non-surgical endodontic treatment.

Observations: Case report 1: A 23-year-old male patient referred by his dermatologist with a cutaneous sinus tract on his chin that had appeared five years ago. During this period, he reported …