Digital Commons Network^™

Angle Cleat Base Connections, M. Dundu, S. Maphosa

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Tests, performed on base connections fabricated from cold-formed channels and hot-rolled angle cleats, are presented in this paper. This research is part of an on- going research to develop portal frames made out of cold-formed steel. The base connections are subjected to an axial load and moment. Hot-rolled angle cleats are used to prevent premature failing of the base connections. Several loading configurations are considered and these are dependent on the eccentricity of the load. In all the tests the cold-formed channels failed by local buckling. A significant amount of bearing distortion was observed in the heavily loaded flange. The …

Cold-Formed Steel For Students A Website, Roger A. Laboube, C. M. Stratman

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

No abstract provided.

Performance Of Knee-Braced Cold-Formed Steel Shear Walls Subjected To Lateral Cyclic Loading, Mehran Zeynalian Dastjerdi, Hamid Reza Ronagh

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Light weight Steel Framed structures currently in use in Australia, are normally braced using face mounted thin straps, cross braces that are of the same shape as studs, or compressed cement boards screwed to the face of the walls. While these are found adequate in low seismic regions of Australia, an investigation into the earthquake resistance properties of LSF have led authors to investigate alternative bracing types that may present a more favourable ductility. Knee braces that are specially designed for this purpose are introduced in the paper and studied in a specially designed testing rig. The tests are on …

Federal Reserve Board Of Governors, Press Release November 3, 2010, Federal Reserve System: Board Of Governors

Documents

No abstract provided.

Three Pirates Named To Pbc All-Academic Soccer Squad, Armstrong State University

Armstrong Athletics: Women's Soccer News (Archived)

Three Pirates Named To PBC All-Academic Soccer Squad. Senior Tracey Mitchell, junior Kelli Bahr and sophomore Kristina Pascutti of the No. 8-ranked Armstrong Atlantic State University women's soccer squad have been named to the 2010 Peach Belt Conference's All-Academic Women's Soccer team, announced today by league officials.

General Motors Can Fly Again For Stock Sale, Bill Vlasic

Documents

No abstract provided.

Volume 48, Number 11: November 03, 2010, University Of North Dakota

University Letter Archive

No abstract provided.

Cwu Faculty Senate Minutes - 11/03/10, Janet Shields

Faculty Senate Minutes

These are the official Central Washington University Faculty Senate minutes for the 11/03/10 meeting.

Slow & Steady, Christin Boggs

Theses

Slow & Steady explores the contemporary movement away from mass-produced food and towards creative alternatives that offer vitality and potency to participants and their surroundings. Within the Greater Rochester Region, individuals have rejected convenience food to responsibly grow, prepare and share sustenance in cooperative groups. The photographs in this thesis depict scenes from community gardens, community supported agriculture (CSA) farms, farmers markets, and other organizations associated with local food production. Here exists a community of resourceful people, coming together in pursuit of good food. Slow & Steady points to one of the ways in which art can effect social change …

Developing A Culturally Responsive Literacy Pedagogy: Preservice Teachers, Teaching Cases, And Postcard Narratives, Annmarie Alberton Gunn

USF Tampa Graduate Theses and Dissertations

The results of the U. S Census provide evidence that our population is becoming more varied and that diversity is most salient in our schools. This demographic shift will continue to have a significant impact on the curriculum, students, teachers, and other aspects of education as we have historically known it. One of the most challenging aspect is that while our students are becoming more diverse, our teacher population is not. Eighty to ninety percent of the teaching population is White, heterosexual, middle class females, with little experiences with people from diverse backgrounds. (Lowenstein, 2009; Sleeter, 2001).

The academic achievement …

Nautical Knowledge: An Experimental Analysis Of The Influence Of Public Relations Strategies In Safe Boating Communication, Emily N. Guilfoil

USF Tampa Graduate Theses and Dissertations

This study explored the effect of public relations message strategies on beliefs,attitudes, and behavioral intentions of individuals regarding boater safety. An experiment was conducted using seven safety messages. Specifically, Fishbein and Ajzen’s (1975) theory of reasoned action and J.E. Grunig’s (1997) situational theory of publics were used to examine the communication effects of message strategies proposed by Hazleton and Long’s (1988) public relations process model.The findings of this study support the predictions of the theory of reasoned action—that salient beliefs predict attitude toward behavior and attitude toward behavior and subjective norm predict behavioral intent. Of the three attitude items measured—attitude …

Percussion Department Fall Concert, November 3, 2010 [Program], University Of Northern Iowa. School Of Music.

Music Recital Programs

Program of a music recital given by faculty, students, or guest artists from the School of Music at the University of Northern Iowa.

Impact Of Corner Radius On Cold-Formed Steel Member Strength, V. Zeinoddini, B. W. Schafer

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The objectives of this paper are to expl ore (a) how corners of cold-formed steel members are included or ignored in current design methods, and (b) the effectiveness of recent proposals for modifying the strength prediction for local buckling to account for corners. The imp act of round corners is examined on the behavior and strength of isolated elements and on full members using material and geometric nonlinear collapse analysis with shell finite elements in ABAQUS. Comparisons between the available methods and the nonlinear finite element analysis are completed to explore the regimes in which the methods are accurate, as …

Cold Formed Steel Tension Members With Two And Three Staggered Bolts, D. M. Fox, R. M. Schuster

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The second edition of the North American Specification for the Design of Cold Formed Steel Structural Members was published in October of 2007 for use in Canada, Mexico, and the United States. This Specification contains two country specific a ppe ndices, namely Appendix A (ANSI/AISI S100- 07) for use in the US and Mexico and Appendix B (CSA S136- 07) for use in Canada. Both Appendix A and B require that a bolt stagger reduction factor of 0.90 be used when calculating the tearing failure strength [resistance] of a cold formed steel member in tension with staggered bolts. This 10% …

Single Shear Bolted Connection Tests Of G500 1.20mm Thin Sheet Steel At Elevated Temperatures, Shu Yan, Ben Young

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The current design rules on bolted connections of thin sheet steels for cold-formed steel structures are applicable for ambient temperature condition only. Research on such kind of connections at high temperatures is limited. In this study, 47 single shear bolted connection specimens fabricated from G500 1.20mm thin sheet steel and 9 coupon specimens were conducted by using steady state test method in the temperature range from 22ºC to 900ºC. Two failure modes were observed in the single shear bolted connection tests, namely the net section tension, and bearing . The test results were compared with the predicted values calculated from …

Strength Prediction Model For Power Acutated Fasteners Connecting Steel Members In Tension And Shear-North American Applications, J. R. Ubejd Mujagic, Perry S. Green, William G. Gould

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Power-actuated fasteners (PAFs), also referred to as pins, are small nail-like or threaded stud t ype connectors. They can be used in conjunction with several materials and in a number of different applications. Typical applications in steel include attachments of deck sh eeting or diaphragms, architectural or mechanical components, or miscellaneous support brackets or connections to supporting steel members. Traditionally, the design strength of the connections featuring power-actuated fasteners has been determined through standardized testing protocols. In the United States, this protocol is embodied in the American Society for Testing and Materials (ASTM) Standard E 1190. The purpose of this …

Study On The Behavior Of Cold-Formed Steel Angle Tension Members, R. Padmapriya, S. Kandasamy

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Cold-formed steel tension members with bolted end connections are frequently used in a variety of structures such as trusses, transmission towers etc. Among all the shapes, angles are widely used. When angle sections are connected with gusset plates and eccentrically loaded, their ultimate load- carrying capacity is influenced by the effect of shear lag. This paper presents the details of an experimental and numerical investigation with a primary objective of studying the effect of shear lag on cold-formed steel single and double angles subjected to tension. Seventy-two single plain and lipped angles made from thicknesses 2,3 and 4 mm connected …

Test And Finite Element Analysis On Distortional Buckling Of Cold-Formed Thin-Walled Steel Lipped Channel Columns, Xingyou Yao, Yanli Guo, Zhiguang Huang

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

High-strength cold-formed thin-walled steel sections have been widely used in the recent several years. However, distortional buckli ng or interaction between it and local buckling can occur for high strength cold-formed thin- walled steel members. This paper desc ribes a series of compression tests performed on lipped channel section columns with V-shape intermediate stiffener in the web and flanges fabricated from cold-formed high strength steel of thickness 0.48 and 0.6mm with nominal yield stress 550MPa. The lipped channel sections were tested to failure with both ends of the columns fixed. The test results of 16 specimens show that the local …

Experimental Evaluation Of A Vehicular Access Door Subjected To Hurricane Force Wind Pressures, Tian Gao, Christopher D. Moen

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This paper describes an experimental study of a rolling sheet door under uniform positive and negative pressure, i.e. wind pushing the door into the building and wind suction pulling the door out of the building. Rolling sheet vehicular access doors are a commonly provided feature in metal building systems. The edges of the door slide freely during regular usage in tracks connected to cold-formed steel jambs. During an extreme wind event, the door engages the jambs with wind locks distributed along both vertical edges of the door to prevent excessive out-of-plane deformation. The goal of the study was to measure …

Experimental Investigation On 6 Feet Wide Cold-Formed Steel Framed Shear Walls With Steel Sheet Sheathing, Cheng Yu, Yujie Chen

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

An AISI sponsored research project on the performance of 6 feet wide cold- formed steel (CFS) framed shear walls with single sided steel sheet sheathing is recently completed at the Un iversity of North Texas. This research project is aimed at determining the required seismic detailing for 6 feet wide 8 feet high CFS shear walls using two steel sheets, one is 4 feet wide, and the other is 2 feet wide. Both monotonic and cyclic tests are conducted and various parameters in the framing and sheathing details are considered in the test program. Those parameters include framing member thickne …

Innovative Damage Control Systems Using Replaceable Energy Dissipating Steel Fuses For Cold-Formed Steel Structures, Fuminobu Ozaki, Yoshimichi Kawai, Hiroshi Tanaka, Tadayoshi Okada, Ryoichi Kanno

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

This paper describes the development of innovative seismic technologies for cold-formed steel structures; a rocking steel shear wall system with replaceable energy dissipating steel fuses for low rise housing units. In this system, the fuses are placed at the base of a folded-steel sheet wall connecting an anchor bolt and the steel sheet wall. It is designed so that most of the earthquake energy can be dissipated by plastic deformation of the fuse elements, while the shear wall remains intact and resists vertical and horizontal forces caused by large earthquakes. As expected in seismic events, the fuses at the base …

Shear Behaviors Of Light-Gauge Composite Walls Under Monotonic And Cyclic Loading, Yuangqi Li, Fei Liu, Zuyan Shen, Xingyou Yao

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

Shear properties of cold-formed thin-walled steel composite walls are af- fected by many factors, including the section of light-gauge studs, the space of self-drilling screws, the panel on both sides of wall, the distribution of hold down device, etc, which makes it is difficult to estimate the shear strength. In this paper, twelve Q345 light-gauge composite wall specimens with a dimension of 2400mm wide and 3000mm high were designed for shear capacity test. Two kinds of panel combination in the specimens were considered, one is gypsum board on one side and OSB board on another side, the other is gypsum …

The Colby Echo (2010-11-03), Colby College

The Colby Echo

Published by the students of Colby College since 1877, The Colby Echo is the weekly, editorially independent student-run newspaper of Colby College in Waterville, Maine. Published monthly, 1877-1886; semi-monthly, 1886-1897; and weekly, during the academic year, 1898-present.

Genetic Evaluation Of American Shad Alosa Sapidissima Restoration Success In James River, Virginia, Aaron Aunins

Theses and Dissertations

The American shad Alosa sapidissima has experienced severe declines throughout its native range due to habitat degradation, fragmentation, and over-fishing. Hatchery supplementation is often used for stock restoration, but the effects of supplementation on population structure and genetic diversity are rarely assessed. This study employed molecular markers to evaluate how supplementation of the James River American shad population with Pamunkey River origin larvae since 1994 has impacted genetic diversity and population structure. Population genetic parameters of other major Chesapeake Bay tributaries (Susquehanna, Rappahannock, Potomac, and Nanticoke) also were characterized. Prior to stocking, the James and Pamunkey populations exhibited subtle genetic …

The Relative Influence Of Demographic, Individual, Social, And Environmental Factors On Physical Activity Among Boys And Girls, Carrie D. Patnode, Leslie A. Lytle, Darin J. Erickson, John R. Sirard, Daheia J. Barr-Anderson, Mary Story

Faculty Publications

Background: This study aimed to evaluate the associations of selected demographic, individual, social, and environmental factors with moderate-to-vigorous physical activity (MVPA) in a sample of children and adolescents.

Methods: MVPA was assessed among youth (n = 294) 10-17-years-old using the ActiGraph accelerometer. Youth completed measures of demographic and individual variables related to physical activity (PA), perceived social support by parents and peers, and perceived neighborhood characteristics. Parents completed the long-form of the International Physical Activity Questionnaire. The Physical Activity and Media Inventory was used to measure the home environment and Geographical Information Systems software was used to measure the physical …

The Parthenon, November 3, 2010, Marshall University

The Parthenon

No abstract provided.

Unemployment Insurance And Low-Educated Single Working Mothers Before And After Welfare Reform, H. Luke Shaefer, Liyun Wu

Upjohn Institute Working Papers

Using the Survey of Income and Program Participation (SIPP), a nationally representative, longitudinal survey, this study examines changing levels of Unemployment Insurance (UI) eligibility and benefit receipt among working low-educated single mothers, 1990–2005. It also examines changing participation in cash welfare and the Food Stamp Program (FSP). Relative to single childless women, there has been no increase in UI benefit receipt among single mothers entering a spell of unemployment in the postreform period, even though single mothers have increased their relative rates of UI eligibility. Because of declining cash assistance receipt, UI became a more common income support than cash …

Annual Hunger Banquet To Be Held November 11, Katie Webb '13

News and Events (Discontinued Series)

No abstract provided.

Newsroom: Kilmartin '98 Is New Attorney General, Roger Williams University School Of Law

Life of the Law School (1993- )

No abstract provided.

Some Aspects On Seismic Design On Frames Designed With Cold Formed Steel Shapes, Gabriel Valencia

CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)

The response of cold-formed steel structures to seismic excitations is not the same as that of structures designed with rolled shapes, in fact, the seismic design codes require that the shapes, meet minimum width/thickness ratios, which virtually no commercial cold formed steel shapes meet, so the design of structures with these elements is excluded from those codes. Different types of beam- to -column connections, made using cold-formed steel shapes have been tested, in order to establish their response to cyclic loads of increasing magnitude. The analysis of these connections using theoretical models with Finite Element Analysis (FEA), and through monotonic …