Digital Commons Network^™

A Comparison Of Training Algorithms For Dhp Adaptive Critic Neuro-Control, George G. Lendaris, Thaddeus T. Shannon, Andres Rustan

Complex Systems Faculty Publications and Presentations

A variety of alternate training strategies for implementing the Dual Heuristic Programming (DHP) method of approximate dynamic programming in the neuro-control context are explored. The DHP method of controller training has been successfully demonstrated by a number of authors on a variety of control problems in recent years, but no unified view of the implementation details of the method has yet emerged. A number of options are here described for sequencing the training of the Controller and Critic networks in DHP implementations. Results are given about their relative efficiency and the quality of the resulting controllers for two benchmark control …

Service Reliability Impacts Of Computer-Aided Dispatching And Automatic Vehicle Location Technology: A Tri-Met Case Study, James G. Strathman, Kenneth Dueker, Thomas J. Kimpel, Rick Gerhart, Ken Turner, Pete Turner, Steve Callas, David Griffin

Center for Urban Studies Publications and Reports

This paper presents findings on initial changes in service reliability following Tri-Met’s deployment of a new bus dispatching system using automatic vehicle location and automatic passenger counter technology. Changes in on-time performance, headway variation, run time variation, and run times were determined with respect to pre-deployment levels. Changes in headway variation and run times were also used to estimate the initial benefits of the new system with respect to operating costs, passenger waiting, and passenger travel time.

Fundamental Study Of The Coating And Basesheet Influences On Gloss In Relationship To Coated Inkjet Papers, Raja Ramakrishnan

Masters Theses

The use of fumed metallic oxides for glossy ink jet media offers alternatives to expensive cast coated and extruded film methods. Fumed metallic oxide pigments provide a high internal porosity and packing porosity that enable the rapid diffusion of liquid inks into the coating layer. Their small particle size (0.1-0.3μm), enable the development of gloss. However, calendering is needed to develop gloss values in the range of cast coated and extruded film grades.

Calendering of coated sheet reduces production speed, adds additional handling and rewinding cost (if performed off-line) and reduces the bulk and porosity of the coating layer, consequently …

Experimental Characterization Of Heat Transfer From An Electrically Heated Thin Filament, Amy J. Cragg

Graduate Theses, Dissertations, and Problem Reports (ETD)

Thin filaments for use in glass, polymer, or textile industries are formed by extruding molten material through an orifice to form a continuous filament. These filaments are cooled rapidly from the melting temperature of the material to near room temperature. If this cooling occurs too rapidly or too slowly imperfections can develop in the filaments. These imperfections can decrease the overall quality and strength of the fiber sometimes leading to temporary production shutdowns caused by filament breakage.;Driven by the need to understand and control the cooling of thin filaments, research has been conducted to attempt to experimentally characterize the heat …

Java Challenge Software Project, Karuna Annavajjala

Graduate Theses, Dissertations, and Problem Reports (ETD)

Programming contests are a means of exploiting the problem solving capabilities of developers and they provide a forum for display of extraordinary programming skills. The Java Challenge (JC) Software Project is the saga of creating an automated, secure and responsive programming contest system for deployment on the Internet and to collect information about programming practices, habits, and trends in coding in such restricted environment. The methodology followed to design, implement, and evaluate such a system uses new technologies such as the WWW, mail filtering and sandboxing techniques. The current Java Challenge implementation runs the Java Challenge on a Solaris 2.6 …

Designing And Modeling A Torque And Speed Control Transmission (Tsct), John Allen Anderson

Graduate Theses, Dissertations, and Problem Reports (ETD)

Near term Hybrid Electric Vehicles (HEVs) generally employ current automotive transmissions. These automatic and manual transmissions are based on designs that are many years old. These older transmission designs do not allow multiple power inputs/outputs to be connected to the transmission. These types of designs significantly limit the flexibility in terms of overall function and component packaging for hybrid vehicles. This study was conducted to determine the feasibility of creating a transmission for hybrid vehicle applications with multiple power inputs/outputs.;The Torque and Speed Control Transmission (TSCT) is a combination of a planetary geartrain and a Continuously Variable Transmission (CVT). By …

Development Of A Method For Calculation Of Cardiac Output Using Doppler Ultrasound, Amit Diggikar

Graduate Theses, Dissertations, and Problem Reports (ETD)

Cardiac output is the amount of blood pumped by the heart in one minute. The Doppler effect can be used to measure cardiac output by measuring the peak frequency, which is directly proportional to the velocity of blood flowing in the aorta, associated with the Doppler shift signal when an ultrasound beam is incident on the aorta. Stroke volume is the product of the cross sectional area of the aorta and the integration of peak velocity over time. Stroke volume times the heart rate is the cardiac output. This project attempts to develop an algorithm that would automatically calculates the …

Modeling And Simulation Of Selected Distributed Generation Sources And Their Assessment, Ju-Chirl Park

Graduate Theses, Dissertations, and Problem Reports (ETD)

The models of small turbine generators (i.e. a combustion turbine, a diesel engine, etc), that are used for distributed generation will be obtained as dynamic. Also, the detailed synchronous machine and the excitation system model are obtained for the standard simulation. The simulation will be performed with an infinite bus system model. The synchronous machine is connected with a local load in order to develop the terminal voltage, avoiding the differentiation.;In order to use fuel cells and solar cells, which are new forms of technology, have the potential to reduce costs, and can be used for the DG in the …

Study Of The Kalman Filter For Arrhythmia Detection With Intracardiac Electrograms, Pisut Raphisak

Graduate Theses, Dissertations, and Problem Reports (ETD)

Third generation implantable antitachycardia devices offer tiered-therapy to reverse ventricular fibrillation (VF) by defibrillation and ventricular tachycardia (VT) by low-energy cardioversion or antitachycardia pacing. The schemes for detecting cardiac arrhythmias often realize nonpathologic tachycardia as serious arrhythmias and deliver false shocks. In this study, an arrhythmia classification technique has been developed with the use of Kalman filter applied on cyclostationary autoregressive model. This new algorithm was developed with a training set of 24 arrhythmia passages and tested on a different data set of 29 arrhythmia passages. The algorithm provides 100% detection of VF on the test set. 77.8% of VTs …

Response Time To Batted Balls, Tracie L. Stechly Seivertson

Graduate Theses, Dissertations, and Problem Reports (ETD)

Traditional wooden bats are being replaced by metal bats. These metal bats can increase the exit ball speed. This study was undertaken to evaluate the effects of the exit ball speed off of a bat on a recreational baseball player's ability to react to the ball.;Ten male subjects, ages 18 to 30, participated in this study. A pitching machine projected balls toward each participant. Each subject was placed behind a safety net and asked to react to the ball as if he was going to field the ball. A radar gun, video cameras, and video editing equipment were used to …

Field Analysis And Design Of A Moving Iron Linear Alternator For Use With Linear Engine, Dulpichet Rerkpreedapong

Graduate Theses, Dissertations, and Problem Reports (ETD)

The previous research at West Virginia University has developed a permanent magnet linear alternator and linear combustion engine for testing and studying the performance. In this prototype, magnets are part of the moving part.;This research will present a new type of linear alternator with permanent magnets installed on stationary called Moving Iron Linear Alternator (MILA). MILA offers several advantages over other types such as rugged structure, and low cost production. First, MILA will be designed for use with the existing linear engine. An optimization methodology will be applied to obtain optimal design parameters. Next, a MILA model will be created …

Tissue Thickness Measurement Tool For Craniofacial Reconstruction, Hari Kinan Gopal Boddupalli

Graduate Theses, Dissertations, and Problem Reports (ETD)

Craniofacial Reconstruction is a method of recreating the appearance of the face on the skull of a deceased individual for identification purposes. Older clay methods of reconstruction are inaccurate, time consuming and inflexible. The tremendous increase in the processing power of the computers and rapid strides in visualization can be used to perform the reconstruction, saving time and providing greater accuracy and flexibility, without the necessity for a skillful modeler.;This thesis introduces our approach to computerized 3D craniofacial reconstruction. Three phases have been identified. The first phase of the project is to generate a facial tissue thickness database. In the …

Verification And Validation In Software Product Line Engineering, Edward Alton Addy

Graduate Theses, Dissertations, and Problem Reports (ETD)

Verification and Validation (V&V) is currently performed during application development for many systems, especially safety-critical and mission-critical systems. However, the V&V process has been limited to single system development. This dissertation describes the extension of V&V from an individual application system to a product line of systems that are developed within an architecture-based software engineering environment.;In traditional V&V, the system provides the context under which the software will be evaluated, and V&V activities occur during all phases of the system development lifecycle. The transition to a product line approach to development removes the individual system as the context for evaluation, …

Performance Evaluation Of Exhaust Aftertreatment Devices Used For Emissions Control On Diesel Engines Employed In Underground Coal Mines, Daniel K. Carder

Graduate Theses, Dissertations, and Problem Reports (ETD)

This study was initiated to assist the WV Diesel Equipment Commission in its promulgation of initial rules, requirements, and standards governing the operation of diesel-powered equipment in underground coal mines. Four different engines and various exhaust after treatment devices that represent current levels of in-use technology were selected for performance evaluation. Both eddy-current and water-brake dynamometers were used to load the engines according to an ISO 8-Mode test cycle. Experimental emissions data, sampled from a full-flow dilution tunnel, suggests that particulate traps can reduce the mass emission rates of particulate matter (DPM) by nearly 90%, while reductions in fuel sulfur …

Optimal Power Flow Using A Genetic Algorithm And Linear Algebra, Reid S. Maust

Graduate Theses, Dissertations, and Problem Reports (ETD)

Artificial intelligence is used to help a hypothetical electric utility meet is electric load economically. The optimal power flow problem (OPF) problem is an optimization problem, in which the utility strives to minimize its costs while satisfying all of its constraints. A genetic algorithm (GA)---a specific type of artificial intelligence-is employed to perform this optimization. To speed convergence, some theory from linear algebra is incorporated into the algorithm.;A GA provides several advantages over more traditional OPF algorithms. For instance, a GA does not constrain the shape of the generators' cost curves and is flexible enough to incorporate control devices such …

Development Of Decision Support System For Reliability, Mitesh Bhupendra Parekh

Graduate Theses, Dissertations, and Problem Reports (ETD)

Reliability analysis is now an essential part of any product development. In the field of Electrical Engineering, reliability models are developed and analyzed for every component before it comes to market. The complexity of the product can range from a simple transistor to an integrated circuit chip, from a simple communication link to a complex network, and from a small generator to a large powerhouse.;Over the period, several techniques have been developed to systematically model real systems and then analyze them. These techniques are constantly being enhanced to improve the modeling process and to reduce the time required for the …

Decision Support Tool For Costing Of The Pultrusion Process, Taher Badrudin Patrawala

Graduate Theses, Dissertations, and Problem Reports (ETD)

The use of advanced composites has grown over the last two decades. These high strength, low weight materials can now be found in many structural applications, including bridges. However, the substitution of plastics for conventional materials, such as steel, is governed by engineering constraints and cost competitiveness. A brief discussion of the process variables and engineering constraints is presented in the first chapter. To analyze the latter and to identify cost centers in production more readily, a computerized cost model was developed. This model estimates the cost of producing components by the pultrusion process.;The technical cost modeling methodology employed involves …

Evaluation Of Ceramic Candle Filters Degradation And Damage Location Using Four-Point Bending Tests, Wu Tseng Peng

Graduate Theses, Dissertations, and Problem Reports (ETD)

The structural integrity of ceramic candle filters is a key element for hot gas cleanup systems. Ceramic candle filters used in demonstration plants have experienced degradation and fracturing. Preliminary examination of these ceramic filters indicated that damage of the filters may have resulted from strength degradation due to persistent high temperature operation, thermal transient events, excessive ash accumulation and bridging, and pulse cleaning. This study proposes a nondestructive evaluation of the structural properties of these ceramic filters. The ceramic candle filter is a slender structure made of layers of porous materials. The structure has high acoustic attenuation, which has greatly …

Characterization Of Particulate Matter And Hydrocarbon Emissions From In-Use Heavy-Duty Diesel Engines, Aleksandar Djordje Bugarski

Graduate Theses, Dissertations, and Problem Reports (ETD)

A continued increase in the use of diesel engines in heavy-duty vehicles, and the uncertainties about the effects of the emissions on human health have focused attention on risk assessments of exposure to the diesel exhaust. The characterization of diesel particulate matter (PM) and hydrocarbon (HC) emissions is the primary objective toward assessing potential health hazard. The dependence of DPM nature on engine/vehicle operating conditions, fuel type, different after treatment processes, and measurement process on the size resolved PM emissions was examined by operating the test engines and vehicles under steady-state and transient conditions. The regional deposition of DPM in …

The Murray Ledger And Times, December 1, 1999, The Murray Ledger And Times

The Murray Ledger & Times

No abstract provided.

The Parthenon, December 1, 1999, Marshall University

The Parthenon

No abstract provided.

Stability Studies Of Coal Liquid Products Using High Performance Liquid Chromatography, Lawrence P. Norcio

Graduate Theses, Dissertations, and Problem Reports (ETD)

The storage stability of coal liquids is of great importance if coal liquefaction products are to replace petroleum products. It has been reported that gum formation occurs in coal-derived liquids during storage to a level at which it becomes a handling problem. The aging of coal hydropyrolysis liquids has been studied. Coal liquid products were placed in preweighed sample vials and stored under light, in the presence of air, at different storage temperatures (2, 21, and 32°C). The weight of gum formed was determined at specified sampling times. High performance liquid chromatography (HPLC) was used to monitor the changes in …

A Summary Of Highway Revenues, Distributions, & Expenses For Indiana Counties, Cities & Towns 1999, John Habermann

Indiana Local Technical Assistance Program (LTAP) Publications

This report provides information on revenues, distributions, and expenses of state and local governments for highway, road, and street work. Since the Motor Vehicle Highway (MVH) and Local Road and Street (LRS) Accounts are the principal source of funds for local road or street construction and maintenance operations, this summary may be used to see the trends in income sources and in the expenses charged to the funds prior to their being distributed to the highway, road, and street agencies.

Off-Line Compression By Greedy Textual Substitution, Alberto Apostolico, Stefano Lonardi

Department of Computer Science Technical Reports

No abstract provided.

Towards The Evaluation Of Netcentric Scientific Applications, Shanhani Markus, Elias N. Houstis

Department of Computer Science Technical Reports

No abstract provided.

Engineering Division, Darla Wagner

Sci-Tech News

No abstract provided.

Brief Amicus Curiae Of The Society Of Catholic Social Scientists In Support Of Respondent, Stephen M. Krason, Richard W. Garnett

Court Briefs

No. 99-138
Jenifer Troxel v. Tommie Granville

On Writ Of Certiorari To The Supreme Court Of Washington

From the Summary of the Argument

The fundamental rights of parents to direct and control the upbringing of their children and the autonomy of the family have been recognized time and again by this Court. These rights and this autonomy are not creatures of positive law, but are grounded in the natural moral order. The family is the "building block" of civil society and has as its natural end, or telos, the nurturing and development of flourishing human persons and good citizens. …

Michael Ondaatje's The English Patient, 'History,' And The Other, Steven Tötösy De Zepetnek

CLCWeb: Comparative Literature and Culture

In his article, "Michael Ondaatje's The English Patient, 'History,' and the Other," Steven Tötösy discusses the historical background of Michael Ondaatje's novel, The English Patient (1992). The historical background and its analysis extend to selected aspects of Anthony Minghella's and Michael Ondaatje's adaptation of the novel to film (1996) and the ensuing controversy after the release of the film. From the historical background Tötösy designates as the "Almásy theme" of the novel and the film, he relates Ondaatje's engagement of the protagonist -- Central European Hungarian László Almásy -- to the notion of the Other as a historical and fictional …

164th Infantry News: December 1999, 164th Infantry Association

164th Infantry Regiment Publications

December 1999 edition of the 164th Infantry News. A total of 20 pages, containing news articles, event notices, photographs, and personal memories from the veterans of the 164th Infantry Regiment.

The Inevitable Infidelities Of Constitutional Translation: The Case Of The New Deal, John O. Mcginnis

Articles

No abstract provided.