Digital Commons Network^™

Mechanical Properties Of Dendritic Pd-Cu-Ga Dental Alloys, Efstratios Papazoglou, Qiang Wu, William A. Brantley, John C. Mitchell, Glyn Meyrick

Cells and Materials

Three Pd-Cu-Ga dental alloys with very similar nominal compositions and dendritic as-cast microstructures were selected for study: Option (Ney Dental) and Spartan (Williams/lvoclar) contain a small amount of boron, while Spartan Plus (Williams/Ivoclar) is boron-free. Bars of each alloy were tested in tension for the as-cast and simulated porcelain-firing conditions, and values of mechanical properties were measured. Fracture surfaces and microstructures of axially sectioned and etched fracture specimens were observed with the scanning electron microscope (SEM). Except for the elastic modulus, significant differences were typically found in alloy properties. Heat treatment eliminated the dendritic microstructure, decreased strength and increased ductility. …

X-Ray Diffraction And Scanning Electron Microscopy Analyses Of A Gallium-Based Dental Restorative Alloy, Randa E. Shaker, William A. Brantley, Qiang Wu, John C. Mitchell

Cells and Materials

Specimens of a gallium-based dental alloy were prepared with different condensation techniques, with and without the removal of a surface layer, and after aging for 2 hours at 50°, 100° and 150°C. X-ray diffraction at times ranging from 10 minutes to 1 day showed the development of the four matrix phases (ß-Sn, CuGa₂, Ga₂₈Ag₇₂, and In₄Ag₉) during the setting reaction. Scanning electron microscope (SEM) examination of specimens loaded to failure revealed brittle fracture, with greater porosity for hand-condensed specimens, and provided insight into crack propagation processes. Aging increased …

Effects Of Casting Conditions And Annealing On Microstructures And Vickers Hardness Of Dendritic Pd-Cu-Ga Dental Alloys, William A. Brantley, Qiang Wu, Zhuo Cai, Stanley G. Vermilyea, John C. Mitchell, Michael C. Comerford

Cells and Materials

Three Pd-Cu-Ga alloys with as-cast dendritic microstructures and very similar compositions, two containing less than 1 wt% boron and the third boron-free, were cast with normal bench-cooling or rapid-quenching into water. Quenched specimens were also heat treated at temperatures of 1000°, 1200°, 1500° and 1800°F that span the firing cycles for dental porcelain. Similar values of Vickers hardness were observed for all three alloys, suggesting little effect from boron on yield strength. The hardness was relatively insensitive to the experimental conditions, except for heat treatment at 1500° and 1800°F where significant softening occurred with transformation of the microstructure to Pd …

Heat-Treatment Behavior Of High-Palladium Dental Alloys, Qiang Wu, William A. Brantley, John C. Mitchell, Stanley G. Vermilyea, Jianzhong Xiao, Wenhua Guo

Cells and Materials

Four high-palladium dental alloys were cast, quenched following solidification, and heat treated at temperatures ranging from 200° to 1,800°F. The Vickers hardness of each alloy was measured, and microstructural changes were studied by scanning electron microscopy (SEM). Phase transformations were investigated by thermomechanical analysis (TMA). Heat treatment at 1,600° and 1,800°F significantly decreased the hardness of one Pd-Cu-Ga alloy, compared to the as-cast condition, as did heat treatment at 1,800°F for the other Pd-Cu-Ga alloy and one Pd-Ga alloy, and yielded fine-grained microstructures of the palladium solid solution. There were generally no significant changes in the hardness of the other …

Mechanism For Formation Of Lamellar Constituents In Grain-Refined Pd-Cu-Ga Dental Alloys, William A. Brantley, Zhuo Cai, John C. Mitchell, Stanley G. Vermilyea

Cells and Materials

Grain-refined Pd-Cu-Ga dental alloys solidify with a lamellar microstructural constituent that affects a variety of clinically relevant properties. While formation of this constituent has been attributed to eutectic solidification, an alternative mechanism of discontinuous precipitation has been proposed. Using a representative grain-refined Pd-Cu-Ga dental alloy, casting procedures involving two different rates of solidification were used: (a) A standard thin-walled coping configuration for a metal-ceramic restoration was cast into a room temperature mold, followed by rapid quenching into an ice-water mixture. (b) A thin plate specimen was cast into a standard elevated-temperature mold, with the same subsequent rapid quenching procedure. Neither …

Effects Of Castration Upon The Morphology Of The Accessory Sex Organs Of The Male Rat - A Scanning Electron Microscopy Study, R. Wahlqvist, E. Dahl, K. J. Tveter

Scanning Microscopy

A systematic, comparative study of the accessory sex glands of the adult male rat after androgen withdrawal was carried out. The changes were investigated by using scanning electron microscopy at different intervals after surgical castration. The main common signs of epithelial cell involution were flattening of the cell surface, reduction of the size and number of microvilli, some blurring of the cell borders, cessation of secretory activity and diminution of the luminal volume of the glands. Overall, confident signs of atrophy were evident after one week, and complete epithelial involution was reached by the third week. The epithelial cell atrophy …

Scanning Electron Microscopy Of The Accessory Sex Glands Of The Adult Male Rat, R. Wahlqvist, E. Dahl, K. J. Tveter

Scanning Microscopy

This study describes the morphology of the accessory sex glands of the adult male rat as observed by scanning electron microscopy (SEM). The purpose was to obtain a systematic and comparative SEM description of these glands and to evaluate different preparation techniques. A common morphological feature is polyhedral delineation of the cells, which exhibited a variable convexity of their apical surface. The cell apices were more or less studded with microvilli. Nevertheless, it was possible to distinguish the glands by their surface morphology. In the ventral prostate, there was a considerable heterogeneity in cell surface appearance. The lateral lobe bad …

Structural And Calcification Patterns Of The Neonatal Line In The Enamel Of Human Deciduous Teeth, Tetsuo Kodaka, Tsuneyoshi Sano, Shohei Higashi

Scanning Microscopy

The neonatal line of the enamel in human deciduous teeth was observed by scanning electron microscopy using secondary and backscattered electron signals. The neonatal line containing irregular structures of enamel prisms with disordered crystal arrangements was basically formed by the abrupt bending of the prisms towards the root. Usually, the prisms gradually bent back again to regain their previous orientation, but the prisms in the inner and the surface layer sometimes ran straight ahead after bending. The prism sheath regions showing hypocalcification contained a relatively large amount of organic material as shown by treatment with chromium sulfate. When etched with …

In Vivo Early Plaque Colonization On Smooth Titanium Surface, A. Carrassi, A. Sardella, L. Rimondini

Cells and Materials

Plaque development on pure titanium in a 24-hour period is described in an in vivo human model. Stents with titanium and root cementum specimens were applied to volunteers, who suspended oral hygiene procedures for 24 hours. The specimens were removed at 2, 4 and 24 hours and studied with a scanning electron microscope. A global area of 240 µm x 300 µm, composed of the sum of twelve 20 µm x 25 µm fields randomly selected, was examined for each specimen. The presence of cocci, short rods, long rods and bacterial aggregation, and bacteria density was recorded for each field. …

A Microstructural Investigation Of Calcium Hydroxyapatites Synthesized From Cahpo4•2h2o And Ca4(Po4)2o, Kevor S. Tenhuisen, Boyd A. Clark, Maria Klimkiewicz, Paul W. Brown

Cells and Materials

This investigation determined the effects of reaction temperature and bulk composition on the microstructural features of hydroxyapatites (HAp) synthesized from reaction between particulate CaHPO₄·2H₂O and Ca₄(PO₄)₂O. These data were used in combination with previous work to further elucidate the mechanistic reaction path taken by these calcium phosphate cements. HAps having two different compositions (Ca/P = 1.50 and 1.67) were synthesized between 15.0 and 70.0°C. All reactions reached completion as indicated by X-ray diffraction. Single point nitrogen absorption was performed on all samples to determine specific surface areas. The HAp which …

Dental Abnormalities And Early Diagnosis Of Hyperphosphatasemia, M. J. Bottero-Cornillac, A. Gaucher, C. Wang, M. Chaussidon, J. Yvon

Scanning Microscopy

Dental hard tissue abnormalities have never been described as part of the symptoms associated with hyperphosphatasemia. Fourteen teeth obtained from a young man, who had a mild form of hyperphosphatasemia, were analyzed using scanning electron microscopy (SEM), secondary ion mass spectroscopy (SIMS), X-ray diffraction (XRD), and infrared (IR) spectroscopy. SEM revealed a thin enamel, presenting a prismatic structure with many pits, and atypical cementum and dentin showing numerous resorption areas. The X-ray diffractograms revealed poorly crystallinehydroxyapatite associated with α-tricalcium phosphate and magnesium hydroxide phases. SIMS data showed high Ca concentrations: 40.5 weight % {wt%; standard deviation (SD) = 0.13) …

Backscattered Electron Imaging And Energy-Dispersive X-Ray Microanalysis Studies Of Evidence For Calcium Salt Heterogeneity In Fifteen Gallstones From An Elderly Human, Tetsuo Kodaka, Ryoichi Mori, Kazuhiro Debari, Reiji Takiguchi, Shohei Higashi

Scanning Microscopy

We examined 15 variably-sized gallstones, taken from an elderly male, by backscattered electron imaging and energy-dispersive X-ray microanalysis to learn the structural and distribution patterns of gallstone calcium (Ca-) salts. Of the 13 cholesterol-rich stones, nine stones had peripheral concentric layers of Ca-carbonate, whereas 2 stones had peripheral layers of Ca-phosphate. No Ca-salts were detected from 2 cholesterol-rich stones. The 2 stones containing Ca-phosphate had no Ca-salt cores, whereas the stones containing Ca-carbonate were separated into 3 different types: two stones with a Ca-carbonate core, four stones with several Ca-bilirubinate cores of glass-like structure, and 3 stones lacking Ca-salt cores. …

Scanning Electron Microscopy And Energy Dispersive Spectroscopy Analysis Of Calciotraumatic Lines In Rat Labial Dentin After Acute Exposure To Strontium Chloride, Hiroyuki Mishima, Toshiro Sakae, Yukishige Kozawa

Scanning Microscopy

Rats were given strontium chloride (SrCli) intraperitoneally at a dose of 500 mg/kg. The upper incisors were removed after injection of strontium. These incisors were studied by scanning electron microscopy - energy dispersive spectroscopy analysis (SEM-EDS) and light microscopy to examine the calciotraumatic lines of strontium in the rat incisor labial dentin.

At 24 hours after injection of strontium, the calciotraumatic response was observed in the predentin using hematoxylin and eosin (H-E) staining. At 5 days, three layers of calciotraurnatic lines were present in the labial dentin using an H-E staining and backscattered electron imaging in the SEM. The external …

Scanning Electron Microscope Study Of The Healing Molar Tooth Extraction Socket In The Rat, M. D. Mcmillan

Scanning Microscopy

Healing molar tooth extraction wounds in rats were examined by scanning electron microscopy from 15 minutes to 40 days following tooth removal. The wound epithelium, which was derived mainly from the gingiva but also from the cheek and hard palate, migrated be-neath the superficial socket contents. The contents were lost between 5 to 11 days, thus leaving a central epithelial-lined depression. This decreased in width with time as the level of the wound epithelium approached that of the hard palate but was still present at 40 days. Between 5 and 7 days, the wound epithelium became more regular. However, from …

Comparison Of Cell Sediment And Surface Grown "Test Plaque" Using Scanning Electron Microscopy, S. M. Mccormack, C. M. D. Maran, K. M. Scott-Anne, D. T. Zero

Scanning Microscopy

Scanning electron microscopy was used to compare the morphology, integrity and distribution of bacterial cells in a test plaque grown on the surface of enamel with that of the cell sediment plaque routinely used in a short-term intraoral caries model. Cultures of S. mutans IB-1600 or S. sobrinus 6715-13 were grown in complex media supplemented with either 2.0% sucrose (glucan plaque) or 0.2 % glucose (non-glucan plaque). Cell sediment (CS) plaque was prepared by centrifuging the cultures after incubation, recovering the cell sediment, and spreading it on Metricel membrane filter paper. Surface grown (SG) plaque was prepared by suspending saliva-coated …

Revascularization Of An Excisional Wound In Gingiva And Oral Mucosa. A Scanning Electron Microscopic Study Using Corrosion Casts In Rats, Nils J. Selliseth, Knut A. Selvig

Scanning Microscopy

The purpose of this study was to examine microvascular regeneration associated with gingival wound healing. A full-thickness piece of gingiva and oral mucosa was excised along the palatal aspect of the right maxillary first and second molars in 20 young Wistar rats. The contralateral side served as unoperated control. After 2, 4, 7, 10 or 20 days of healing, microvascular corrosion casts were produced and examined by scanning electron microscopy. At 2 days, vessels surrounding the wound were dilated and impressions representing sites of leukocyte margination were prominent in the walls of venules. Capillary buds were emerging from venules and …

Scanning Electron Microscopy Studies Of Ceramic Layers And Interfacial Regions For Calcium Phosphate-Coated Titanium Dental Implants, W. A. Brantley, E. Tufecki, J. C. Mitchell, D. W. Foreman, E. A. Mcglumphy

Cells and Materials

The surface and cross-section characteristics of the plasma-sprayed calcium phosphate coatings, along with the microstructures and elemental compositions near the titanium alloy interface, were investigated by scanning electron microscopy for two different dental implants of proprietary compositions: Integra!® (Calcitek) and BioVent ® (Dentsply). Elemental concentrations (Ca, P, Ti, AI, and V) near the interfaces were obtained by X-ray energy-dispersive spectroscopy. Coating surfaces exhibited a splat deposition topography of greatly differing microstructural scale for the two implants, along with other features characteristic of the plasma-spraying process; cross-sections of the coatings revealed minimal porosity. Some interdiffusion of principally titanium and calcium was …

Room Temperature Aging Of Pd-Cu-Ga Dental Alloys, William A. Brantley, Zhuo Cai, Qiang Wu, Alan B. Carr, John C. Mitchell

Cells and Materials

Specimens of three Pd-Cu-Ga dental alloys cast five years ago and subsequently stored at room temperature were reexamined and observed to have lower amounts of the eutectic constituents in the near-surface region than originally present, along with other microstructural changes. This previously unreported room temperature aging behavior of these alloys is attributed to the presence of high-diffusivity paths in the non-equilibrium ascast eutectic structures and to the essential role of the surface for the vacancy diffusion mechanism. These results may have important clinical significance for the ill vivo corrosion resistance and long-term biocompatibility of the Pd-Cu-Ga alloys.

Ultrastructure Of Dentin Matrix In Heritable Dentin Defects, J. Waltimo, H. Ranta, P. -L. Lukinmaa

Scanning Microscopy

Heritable dentin defects form a group of diseases which exclusively affect dentin among the various dental tissues. While one type is associated with the generalized connective tissue disorder, osteogenesis imperfecta, other types occur as single traits. The clinical manifestations of the dentin defects vary from insignificant to severe enough to cause aesthetical and functional failure of the teeth. Scanning and transmission electron microscopic studies, reviewed in this paper, have markedly clarified the ultrastructure of the aberrant dentin matrix. Both similar and different changes seem to occur in the various forms of heritable dentin defects. Abnormalities in the appearance and organization …

Scanning Electron Microscopy And Energy-Dispersive X-Ray Microanalysis Studies Of Several Human Calculi Containing Calcium Phosphate Crystals, Tetsuo Kodaka, Kazuhiro Debari, Tsuneyoshi Sano, Masayuki Yamada

Scanning Microscopy

Human calcium phosphate calculi: two sialoliths, a urolith, a rhinolith, and a tonsillolith were investigated by scanning electron microscopy (SEM) and energy-dispersive X-ray analysis (EDX). The sialoliths and urolith had appositional shells with thick cortices, respectively, around several nuclei composed of calcospherulites and a rubber-film fragment. The rhinolith had a thin cortex with appositional laminations around a glomerulus-like mass of calcified cotton-like strings. The tonsillolith had a rough cortex with appositional laminations. Its porous interior was composed of numerous calcified conglomerates with microorganisms and calcified masses with fine appositional laminations around the conglomerates. The major crystals were identified as biological …

The Microvasculature Of Human Infant Oral Mucosa Using Vascular Corrosion Casts And India Ink Injection Ii. Palate And Lip, Q. X. Yu, K. M. Pang, W. Ran, H. P. Philipsen, X. H. Chen

Scanning Microscopy

The microvasculature of human hard and soft palate and lip originating from four infant males and six females, aged 6 months to 2 years was studied by scanning electron microscopy of vascular corrosion casts and light microscopy of India ink injected specimens. The capillary loops of the hard palate mucosa and vermilion border of the lips were found to be tall, numerous and consisted of primary, secondary and tertiary loops. Those of the soft palatal and labial mucosa were short, few in number and demonstrated a simple hair-pin shape originating directly from the subpapillary vascular network. It was concluded that …

Calcium Phosphate In Aspergillosis Of The Maxillary Sinus, Hidekuni Tanaka, Toshiro Sakae, Hiroyuki Mishima, Hirotsugu Yamamoto

Scanning Microscopy

The unique appearance of apatite in fungus balls of aspergillosis in the maxillary sinus was investigated using scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), X-ray microdiffraction and Fourier transform infrared spectroscopy (FT-IR). Rod-shaped fragments with tubular structures, and globular vesicles covered with conidia were observed in the fungus balls. Massive fragments of a solid substance were demonstrated inside the fungus balls. Calcium and phosphate were detected in necrotic areas of the fungus balls by EDS. X-ray microdiffraction and FT-IR showed the presence of an apatite-like substance, but failed to demonstrate the presence of calcium oxalate crystals usually found in such …

Migration Of Epithelium During Phenytoin-Dependent Gingival Overgrowth In Mice, S. H. Ashrafi, B. Atassi, R. Erickson, T. Sabet

Scanning Microscopy

A small cavity was made in the mesiopalatal area of the maxillary first molar adjacent to the gingiva. Mice were maintained on 40 mg/kg phenytoin (or on diluent for control) by daily intraperitoneal injections. After 9 weeks, light microscopic observations revealed that in experimental mice, epithelial cells migrated towards the cavity and covered it. In controls, epithelial cell migration towards the cavity did not occur. For scanning electron microscopic (SEM) studies, specimens were fixed in 4% glutaraldehyde in 0.1 M phosphate buffer, pH 7.2, for 2 hours, dehydrated, critical point dried and coated with gold. The surface of the outer …

Observations On The Enamel Of Odontomas, Carla Marchetti, Cesare Piacentini, Paolo Menghini, Marcella Reguzzoni

Scanning Microscopy

The morphological study of odontomas provides an alternative model for observing the formation of dental tissues, since different maturing stages are present simultaneously. Investigations were performed on decalcified samples (using light microscopy and transmission electron microscopy) and on undecalcified samples of complex odontoma enamel (using transmission electron microscopy). Simultaneous presence of prismatic enamel at various maturing stages with different structural characteristics was observed. Such enamel was sometimes associated with layers of ameloblastic cells with characteristics of cells in functional activity. In other sites, the enamel did not present a prismatic structure but it appeared as unstructured material clusters with abundant …

Sample Preparation Techniques For Conventional And High Resolution Scanning Electron Microscopy Of The Central Nervous System. The Cerebellum As A Model, Orlando J. Castejon

Scanning Microscopy

In the present paper some basic sample preparation techniques for scanning electron microscopy of nervous tissue are described. These basic preparative methods include conventional scanning electron microscopy or slicing technique, ethanol-cryofracturing technique, freeze-fracture method using either liquid nitrogen (slow freezing) or Freon 22 cooled by liquid nitrogen (fast freezing), improved freeze-fracture method with delicate specimen preparation and chromium coating, ultrasonic microdissection, and "creative tearing" technique. Some basic principles, advantages and limitations are critically considered. In addition, some specific applications in neurobiological research are reported. Emphasis is placed upon understanding the sources and nature of artifacts that are likely to be …

Identification Of The Physical Modification Threshold Of Dentin Induced By Neodymium And Holmium Yag Lasers Using Scanning Electron Microscopy, J. M. White, H. E. Goodis, G. W. Marshall Jr., S. J. Marshall

Scanning Microscopy

Laser application to dentin has been advocated to modify the dentin substrate for restorative procedures. We examined the minimum energy density required to physically modify the dentin surface using 1.06 μm and 1.32 μm Neodymium:Yttrium-Aluminum-Garnet (Nd: YAG) and 2.10 μm Holmium-YAG (Ho: YAG) lasers. Three millimeter thick dentin sections from the middle occlusal third of crowns of third molars were used. To determine the effect of surface preparation, the sections were ground to 240, 320, 400, 600 grit or polished to 0.5 μm. Smear layer was removed using 0.5 M EDTA for 2 minutes. Five single pulse repetitions at each …

Scanning Electron Microscopy Of The Osteoclast-Bone Interface In Vivo, H. Zhou, R. Chernecky, J. E. Davies

Cells and Materials

Rat femoral bones were studied by scanning electron microscopy to demonstrate the morphology of osteoclast- bone matrix interfacial relationships. Two general morphological types of actively resorbing osteoclasts were observed . One cell type was approximately ovoid with highly fimbriated borders, fully attached and closely adapted to the resorption surface. The ruffled border of such cells was composed of a number of individual filopodia which were of uniform , regular shape and approximately 2-3 μm in length and 150 nm in diameter. They were found to penetrate the bone matrix to a depth of 1 μm and interdigitated with the surrounding …

Metallurgical Structures Of As-Cast And Heat-Treated High-Palladium Dental Alloys, William A. Brantley, Zhuo Cai, Alan B. Carr, John C. Mitchell

Cells and Materials

Scanning electron microscope observations and energy-dispersive spectroscopic analyses have been performed on two first-generation and two second-generation high-palladium dental casting alloys. A specimen design simulating a maxillary central incisor coping was employed to conserve metal, while providing thin and thick sections to yield a range of solidification rates. The alloys were centrifugally cast in air, following standard dental laboratory techniques; three castings were prepared for each alloy. Each casting was sectioned to produce two mirror-image specimens, and one specimen received the appropriate oxidation heat treatment, followed by a simulated full porcelain firing sequence. After metallographic polishing, specimens were examined with …

Calcospherites In Rabbit Incisor Predentin, H. Mishima, Y. Kunuki, T. Sakae, Y. Kozawa, N. Watabe

Scanning Microscopy

Calcospherites from the lower incisor dentin of rabbits were investigated by scanning and transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS) and electron diffraction analyses. In the labial predentin, globular calcospherites of 8-31 μm were present at the root apex, decreasing in size toward the incisal region. The calcospherites at the intermediate region were of mulberry- as well as of spindle-shape of 1.5-4 μm diameter. The incisal pulp horn contained micro-calcospherites of 0.3-0.6 μmin diameter. In the lingual predentin, small granular calcospherites of 1. 8-3 μm were present at the root apex, increasing in size toward the intermediate region. Ultrathin …

Scanning Electron Microscopy Of Intracellular Organelles In The Young Odontoblasts Of Rats, Yasutomo Iwai-Liao, Yoshikage Higashi, Masakazu Ishikawa, Hideaki Hori

Scanning Microscopy

Intracellular structures of the odontoblasts were studied by scanning electron microscopy (SEM) using a modified AODO (aldehyde prefixed-osmium-DMSO-osmium) method. Well-developed flattened and layered rER (rough endoplasmic reticulum), paved with its associated ribosomes on its outer surface, were clearly observed in the odontoblast. Branched tubular mitochondria with nodules and swollen endings, interposing between and passing through the fenestrated layered rER, were demonstrated in the functional cells. Oblique and cross-sections of both the rER system and tubular mitochondria showed orthodox configurations similar to those usually described in transmission electron microscopy (TEM) studies. Many finger-like projections constructing the cristae directing towards the inner …