Digital Commons Network^™

Plate Stress Analysis By The Finite Element Method, Wen-Jung Chuang

Theses

The finite element formulation of plate elasticity is presented and is employed in the development of the formulation of element stiffness equations. The programming structures are also summarized.

The finite element program PLATE cited from Prof. J. N. Reddy's " An Introduction to the Finite Element Method " has been used to solve the plate bending problems with quadrilateral elements. The problems solved are:

(1) deflections and stresses in a circular plate with all edges simply supported under uniform load.

(2) deflections and stresses in a circular plate with all edges clamped under uniform load.

each case including four different …

An Analysis Of Different Desalination Processes, Vahe Garabed Hovsepian

Theses

The object of this thesis is to study the various modes of desalination and analyze the energy and economic requirements. The desalination methods discussed are, single stage desalination, Long tube vertical Evaporator, Multistage Flash distillation, Solar Energy method, Freezing method, Reverse osmosis & Electrodialysis.

It was found that for vapor reheat process at 350°F input 639 ft-lbs/lb product required 2.01 kw-hr/100gal. product and the total cost 51.6c/1000gal.

Not one process is best for everyone. In countries close to the equator, the solar energy method is the best. Most other countries depend on flash distillation process, etc. So we can't draw …

Implementation Of Finite Element Method On A Microcomputer, Chi-Yuang Huang

Theses

A finite-element program FEM2D has been implemented on a PHILIPS microcomputer. The program has a generation preprocessor and thus makes finite-element analysis on a microcomputer considerably easier than before, since it allows models to be created and edited much faster than by manual method. The interactive program FEM2D prompts the user to input data directly from the screen. It is convenient for the user, both in teaching and learning.

The FEM2D is a two-dimensional finite-element program capable of solving two-dimensional problems, such as plane elasticity, heat transfer and imcompressible fluid flow problems. It is developed with a formulation of a …

College Relations : A Total Recruiting Strategy, Donald Roderick Hunt

Theses

Problem Statement

The MMH Corporation has a very experienced but older engineering population. It is management's desire to replace the engineering population as its members retire by two methods:

1. The recruitment of experienced engineers with key skills for various critical positions.

2. The development of an aggressive and effective College Relations Program targeted at key universities to attract a steady stream of new talent into the engineering populations.

Research Objectives

A. To determine what areas of a volatile marketplace MMH intends to compete in.

B. To determine what attracts the best new college graduates to a certain company as …

In Vitro Comparative Hydrodynamic Study Of Heart Valve Bioprostheses Under Accelerated Fatigue Conditions And Under Physiological Conditions, Mario Cincinat Iosif

Theses

The present study involves the use of an accelerated fatigue testing system*, and a pulse duplicator (heart simulator)*, to evaluate the hydrodynamic characteristics of cardiac bioprostheses.

The hydrodynamic performance of these prosthetic valves is compared when tested using each machine, in order to assess the determining conditions that exist for each case, and try to correlate them.

Pressure drop and pulsatile flow across valves are measured, using a real-time on-line data acquisition system, which includes, in addition to the fatigue tester and the pulse duplicator, a DC amplifier, an analog-to-digital converter and a digital microcomputer. Special acquisition software has been …

Microcomputer Local Area Network Interface, David W. Juan

Theses

A Microcomputer Local Area Network Interface system for use in the study of Local Area Network has been built and tested. The special feature of the system is data transmission/receiving and error detection/recovery. The system adapted the International Standards Organization (ISO) Open System Interconnection COSI) model. It used the star topology and implemented the physical layer, data link layer and network layer. The results of the system indicated the data communications and resources—sharing between microcomputers.

Study Of The Effects Of Pumping Pressure On The Properties Of Fresh Concrete, Dinesh Vithal Kenkre

Theses

This thesis has a two-fold objective. One, to develop a suitable testing apparatus in the labaratory to simulate the effect of field pumping of concrete and two, to conduct some preliminary tests to investigate the feasibility of the testing apparatus.

Pumping of concrete has been practiced in the U.S.A. since 1930. The behaviour of concrete in a pipeline has not been studied in much detail while development in the pumping technology raced ahead of the research in this field. Previous studies done in this field have clearly indicated the need for a laboratory simulation of pumping process in order that …

Computational Method For Robot Manipulator Dynamics Based On The Gibbs-Appell Equations, Kwang Bok Kim

Theses

Industrial robots are open-loop multi-degree of freedom mechanisms whose dynamic characteristics are described by nonlinear differential equations. The computations of forces and torques required at each joint of robot manipulator are crucial step for real time control of robot manipulators.

Vukobratovic developed a new computational method for rigid body articulated open-loop mechanisms based on the Gibbs -Appell equations to generate differential equations of motion for spatial open - chain mechanisms. To solve these equations, he introduced the recursive kinematic transformation matrices that represent the motion of each linkage with respect to the base linkage.

Computer programs are developed in this …

Laminar Flow In A Porous Pipe With One Plugged End, Pyne-Hwa Ku

Theses

A steady laminar flow through a co-cylinder porous pipe with one plugged end was investigated theoretically to obtain velocity, pressure and shear stress distributions.

An integral momentum equation and the Darcy's law for flow through the porous wall were solved numerically by the Runge-kutta method.

As the fluid is injected from the outer wall into the porous tube, the fluid in the inner tube is accelerated from rest at the plugged end to a fully-developed velocity profile at the exit of the porous tube. It was found that the coefficient of the wall shear stress and the dimensionless pressure drop …

Preparation And Properties Of Monomers Derived From Hydroxyhexyl Methacrylate For Dental Adfesive, Ren-Dar Ku

Theses

Although methacrylic acid is the simplest unsaturated carboxylic acid and its hydroxyl ester polymerize readily, yielding useful resins, no adequate study of the preparation and application of the higher hydroxyl alkyl methacrylates has been published. The commercially important hydroxyethyl and hydroxypropyl methacrylates are manufactured from the appropriate alcohol in the presence of sulfuric acid, a method which appears to be less suitable for production of higher hydroxyl alkyl methacrylates. The purpose of the present work was to prepare the hydroxyhexyl methacrylate (HHMA) by a generally applicable method and determine its common physical properties. In addition, the urethane methacrylates were synthesized …

Computer Aided Mathematical Modeling Of A Once Through Claus Type Sulfur Recovery Process, Yuriy Osyp Kutny

Theses

The computer aided mathematical modeling of the once through Claus process for hydrogen sulfide conversion to sulfur is presented herein. This vapor phase oxidation reaction is carried out using one thermal reactor and up to three bauxite catalytic reactors with sulfur condensers in between. The method of catalytic reactor feed reheat and its ramifications upon reactor performance and total model convergence is of major importance.

The reactor feed preheat can be carried out in either of the following ways: (1) indirect heat exchange using some external heat source; (2) indirect heat exchange using other hot process streams as heat source; …

Design And Evaluation Of Performance For The Multi-Microprocessor System, Sang-Soo Lee

Theses

A tightly coupled multiple-microprocessor with two MPU's that can be run at different clock speeds has been built and tested. The method of interconnection for this multiprocessor is a timeshared common bus with shared memories having a tightly coupled architecture. The signal timipg of the multiprocessor system for different speeds has been investigated using a logic analyzer for simulation modeling. The desired timing results have been obtained. According to the timing results, the simulation model for the General Purpose Simulation System has been correctly designed and performance of the multiprocessor system for the various clock speeds has been evaluated by …

An 8052 Ah - Basic, Based Development System, Suresh Vishwanath Leley

Theses

This project exploits the latest in microcontrollers-an entire environment for developing and prototyping a microcontroller application. With one key chip, a little glue, and a Dumb terminal a powerful system is achieved at a vanishingly small cost. This "one chip" system is adequate for realizing a wide range of applications calling for a small computer or an embedded processor.

Besides economy of system cost, the turn around time from concept to functioning application can be extremely short, even when the development engineer is not particularly well acquainted with traditional assembly language and microprocessor development practices. This economy is achieved by …

Stress Analysis Of A Pressure Vessel By The Finite Element Method, Hsin-Te Liao

Theses

The objective of this paper is to take a finite element program, called ANSYS, to analyze the surface stress distribution of a thin-wall pressure vessel with a spherical head.

The computer program ANSYS, which primarily applies the principle of virtual work in solid continuum, has been used to solve shell problems with quadrilateral element. Problems solved are: <1> hoop stress <2> meridional stress (<)3) maximum shear stress.

In this paper, the theoretical finite element formulation of axisymmetric elasticity of the ANSYS program is presented.

Finally, some numerical examples of shells with spherical heads of various radius are given. The solution obtained from ANSYS is very …

Linearization Accuracy In Probabilistic Load Flow, Guan-Zhong Liang

Theses

This paper presents a linear load flow method which can be used for probabilistic load flow analysis. The method is based on least-square estimation. To estimate its accuracy in linear load flow calculations, the method and a previously developed linear load flow method are applied to a typical power system and the results evaluated. Comparable accuracy is noted.

Air Pollutant Emissions From Non-Vented Radiant Kerosene Heater, Anil Kumar Mishra

Theses

Gaseous emissions from non-vented kerosene heaters can generate and create significant indoor air concentrations of various gaseous pollutants. Indoor air concentrations resulting from operating a portable non-vented radiant type kerosene heater in three rooms of size 38.7, 58.1 and 137 M³ were studied. Studies in the environmental chamber having a size of 38.7 M³ under two sets of ventilation conditions showed elevated levels of CO₂, total hydrocarbons and CO. An emission rate model was used to estimate the strength of pollutant source, for total hydrocarbons, CO₂ and CO with data reported in terms of mass …

The Cocoa Rehabilitation Project In Ghana, Kwane Boakye Dankwah

Theses

Several studies have been done in an attempt to find out the cost involved in establishing an acre of cocoa farm and most of these used the questionnare method to gather the information. However, most data gathered this way did not include detail establishment cost information on inputs as the farmers relied on recollection of cost they incurred.

The study done by C. Okali at Dominasi in the Brong Ahafo Region did not follow this pattern. Data collection for this study was started in May 1971 and ended in September 1972 and there were 45 farms involved. This sample was …

Reliability Study Of Liquid Crystal Display, Kalpesh Mahendra Desai

Theses

The purpose of this thesis is to study the reliability of liquid crystal display under different temperature conditions. To accomplish this, accelerated life testing was done on the soft glass and the hard glass liquid crystal display units at 77 C and 85 C temperature without any added humidity or voltage.

As the current is a usefu1 indicator for probable wear of liquid crystal display, leakage current was measured at 0 hour, 1000 hours, 2000 hours and 3000 hours when the units have stabilized at room temperature.

The date shows higher spread for the hard glass units. This may indicate …

Systems Building Theory Application Within The Residential Housing Construction Market, Gary Alexander Newhard

Theses

The primary purpose of this report is to introduce the economical value in utilizing certain "systems building" applications. In this report I focus on integrated system methodologies that encourage residential building economy and submit such systems as a viable alternative to traditional labor intensive housing construction. The consumer market that could be particularly enhanced by these systems ranges from low income to middle income and the by-product would be classified as "affordable" housing.

This report focuses on the New Jersey real estate market and presents certain prefabricated housing systems as an economical means of meeting the large demand for residential …

Modal Analysis Of A Cantilever Plate, Ohseop Song

Theses

This thesis discusses the vibration of a thin, flat cantilever aluminum plate. Results are based on both an analytical finite element method using the ANSYS program and an experimental analysis using a digital Fast Fourier Transform (FFT) analyzer. The FFT analyzer permits extraction of modal parameters (natural frequency, damping, mode shape) for the plate.

Biodegradation Of Multiple Substrates In A Batch Reactor, Nilesh Naik

Theses

The biological degradation of multiple substrates was studied at room temperature in aerated 5-liter batch reactors using mixed liquor from the Passaic Valley Sewerage Commissioners wastewater treatment plant (Newark, New Jersey).

Two substrate mixtures were used (with initial concentration indicated in parenthesis): (1) phenol(100ppm) + nitrobenzene(10ppm) + 2,6-dichiorophenol(10ppm); (2) 2-chlorphenol(20ppm) + nitrobenzene(10ppm) + 2,6-dichlorphenol(10ppm). From concentration versus time data, kinetic rate constants for zero-order, first-order, and Monod models were determined. Most of the data were best fit by either the Monod or zero-order model. For all compounds tested biodegradation was the primary removal mechanism, and in many cases the rate …

Measurements Of Basic Semiconductor Properties, Abdolreza Ariantaj

Theses

Mobility, resistivity, and total impurity concentration of several purchased p-type silicon samples with known resistivities were measured by Hall effect, experiments utilizing the Van Der Pauw method. The silicon samples will serve as Hall effect standards for future measurements on other semiconductor materials, particularly gallium nitride ion cluster beam (ICB) deposited thin films. The samples which were Freshly etched with hydrofluoric acid had measurement values of 455 cm ² / V.sec, 45.9 Ω cm, and 2.6 X 10¹⁴ cm³ for mobility, resistivity, and total impurity concentration, respectively. The mobility values were within 9.9 per cent, of the published values …

The Acquisition Of Direct Sequence Spread Spectrum Communication Systems, Anthony Donald Demeri

Theses

This Paper surveys different techniques of acquiring Direct Sequence Spread Spectrum Systems.

It classifies different systems, indicates the strongpoints and weakness of each, along with some applications.

One method, The Single Dwell Serial PN Acquisition System is then focused on in detail. The detail includes analysis of standard version, derivation of the mean time to acquire, the variance, the probability of detection and the probability of a false alarm.

In the last section of the paper the analytical results of the Single Dwell Serial PN Acquisition System shall be confirmed by computer simulation.

Substructuring Analysis For Impact Dynamics Using Ansys Finite Element Package, Chang Ho Cho

Theses

This thesis is intended to serve as an introductory guide to ANSYS finite element package for the analysis of impact dynamics. Substructuring technique has been used to reduce the degrees of freedom.

Finite element method is essentially a numerical technique to calculate elastic deformations. However, by introducing some techniques like gap element, the technique can be easily extended to rigid body dynamic analysis. To solve the equation of motion both for rigid body and elastic deformations, direct integration technique is used in this thesis, i.e., Houbolt method.

ANSYS is a large scale general purpose computer program for finite element analysis. …

Emergency Stop Devices And The Human Factors Of Response, Robert Paul Guinter

Theses

The manual emergency stop Was recognized as an im- portant aspect of machine control very early during the history of powered mechanical systems. The purpose, of course, was to allow machinery to be quickly stepped during emergencies to minimize equipment damage and/or personal injury. Today, however, the emphasis of control is being shifted more and more toward totally automatic systems. Often, the importance of manual emergency stopping and override of these systems is lost in the zeal to perfect automatic controls. The problem that evolves is how and when to provide an efficient human-machine interface to allow a manual emergency …

Circular Plate Analysis Using Finite Element Method, Shyh-Rong Chiu

Theses

The ANSYS computer program is the application of finite element methods to large-scale engineering problems. In this work the ANSYS program has been employed to solve the circular plate under uniformly loaded with various boundary conditions as follows: (1) clamped along entire edge, (2) simply supported along entire edge, (3) clamped at several points along the boundary, (4) simply supported at several points along the boundary, and (5) simply supported 36 points with 4 points clamped..

The results obtained from the ANSYS program illustrated that the finite element method has no boundary conditions constraints and presents good approximations to the …

Black Working Women And Equal Employment Legislation, Barbara Donese Mitchell

Theses

The research for this thesis is undertaken in order to examine whether or not equal employment legislation improved opportunities in the workplace for Black working women. The following areas will be focused on:

- Legislation - Civil Rights Act of 1964, Equal Employment/Affirmative Action, Equal Pay Act, and Title IX.

- Racism/Sexual Harassment

- The Public and Private Job Sector

- Unions

- Academia/Education

- Politics

Some sources for examination will include studies by researchers from various universities on Black women and employment, statistics from the U.S. Labor Bureau, National Research Council and Joint Center for Political Studies, and reports …

Introductory Guide To Bridgeport Series I Cnc Milling, Drilling And Boring Machine, Apurva Vinodchandra Doshi

Theses

This thesis is intended to serve as an easy introductory guide on how to work with Bridgeport Series I CNC Milling, Drilling and Boring machine. An attempt has been made to make the subject matter simpler to give the reader a good start in programming and operating this machine

The spectrum of technological implementation of CNC machine tools is extremely broad,. Companies utilizing advanced technologies such as computer graphics, DNC and Group Technology are in this field for some time. Even small shops are getting equipped with CNC machine tools. The present CNC systems, which are less costly, more reliable …

Fracture Energy And Tensile Behavior Of Concrete, Wen-Jinn Chiou

Theses

Fracture behavior of concrete has been a subject of investigation for the past two decades. The need of understanding the complete tensile response of concrete is absolutely essential for theoretical modelling as well as design application of plain concrete structures.

In this study, attempts were made to investigate the validity of two important fracture parameters, namely, the fracture energy and the critical crack tip opening displacement. Three types of test specimen, dog- bone shaped tension specimen, notched beam and compact tension specimen, were investigated. These tests were conducted using the closed-loop MTS 810 strain-controlled testing system. For the uniaxial tension …

A Research Study To Determine The Characteristics And Attitudes Shared By Entrepreneurs And Intrapreneurs And The Similarities And Differences Between Them, Miguel A. Vargas

Theses

The United States of America has been the mecca of many ventures for people with vision, goals and perseverance. The prosperity of our nation has been paved by individuals with great ambition, determination and insight, who have dared to take on a risk in owning a business enterprise.

This research study was conducted to determine the characteristics and attitudes of both entrepreneurs and intrapreneurs, as well as the similarities and differences between them.

For this study, a survey of entrepreneurs.was conducted through the use of questionnaires distributed to business owners located in the counties of Essex, Passaic and Hudson, in …