Digital Commons Network^™

Epoxy Resin Admixture For Concrete, Kuo-Chu Hu

Masters Theses

"This thesis describes laboratory tests on concrete having epoxy as an admixture. Cylinders for compression and elastic modulus tests were cured under two different curing conditions, standard laboratory cure and a simulated job cure. Beams cured under laboratory conditions were tested for flexural strength. Test results show the compressive strength increases with an increase of epoxy content for job curing conditions. However, compressive and flexural strengths of specimens cured under laboratory conditions show a slight decrease. The elastic modulus of concrete containing epoxy also decreases in comparison to ordinary concrete"--Abstract, page ii.

A Study Of The Photomechanical Effect In Silicon, Ronald M. Oglesbee

Masters Theses

"This paper presents the results of an experimental investigation into the photomechanical effect in silicon. The effect was found to be very similar to the electromechanical effect. In both cases the phenomena observed is the softening of a thin surface layer of the material when it is either illuminated or when a current is flowing through the material. An anisotropy was observed in both the hardness and the photomechanical effect. Increasing temperatures tended to "washout" the photomechanical effect. The surface hardness and the photomechanical effect were found to depend heavily on proper surface preparation of the samples, however little dependence …

Design Of Non-Uniform Linear Antenna Arrays With Digitized Spacing And Amplitude Levels, Jack F. Morris

Masters Theses

"Recent developments in space exploration have shown a need for high resolution, high gain antennas. The introduction of non-uniform linear array theory has provided a means by which arrays may be designed to produce narrow main beams with fewer elements than required by uniform arrays. A general theory has not been developed, however, and the design engineer has been left with only trial-and-error methods with which to work. In this study a technique has been developed by which non-uniform antenna arrays may be synthesized to meet a given set of specifications with reasonable accuracy. The elements of the array are …

Tschebyscheff Fitting With Polynomials And Nonlinear Functions, George F. Luffel

Masters Theses

"It is the purpose of this study to survey the properties of the Tschebyscheff polynomials with particular reference to how they are employed as approximants and interpolants. The survey is extended to include the process known as "Tschebyscheff Approximation" or "Tschebyscheff Fitting" of a function by functions other than polynomials. One such fitting technique which will be of particular interest in this study is that of fitting f(x) by the function ab^x + c where a, b, c are real and b ≠ 1. In addition to a survey of the properties of the Tschebyscheff polynomials and of Tschebyscheff …

Optimum Finite Memory Nonlinear Filter, Ching-Chyoun Yang

Masters Theses

"This thesis investigates the possibility of using the Zadah theory and a machine type computer to design an optimum finite memory nonlinear filter for extraction of Poisson distributed signal pulses from a background of Gaussian noise. Basically the procedure involves the technique of solving simultaneous equations by the computer. We demonstrate that it is possible to find the limitation of the filter of class N₁ in terms of an absolute minimum mean square error. However, due to the capacity of the computer we do not actually determine the absolute minimum. Nevertheless we do show that the mean square error decreases …

Radial Water Encroachment - An Approximation, Tommie C. Wilson

Masters Theses

"This presentation consists of the application of empirical equations for the calculation of the water influx into a radial oil reservoir in which the history of the rate and cumulative water influx are equated to the pressure decrements and time. This new analysis, based on William Hurst's solution for the steady-state water influx, yields an accurate method for determining water influx through the application of simple linear empirical equations. These linear approximations reproduce the rigorous influx solutions to a maximum deviation of 1.6 per cent"--Abstract, page ii.

Use Of Spent Sulphite Liquor For Stabilization Of Fractured Rock And Sealing Off Water Bearing Formations, Laxman Singh Sunda

Masters Theses

"The paper industry, in its process of manufacturing pulp from wood, produces large quantities of a substance called lignin, lignin sulphite, or lignosulphonate. This material has been disposed of as a waste product; however, it does have many potential uses. In this investigation, lignosulfonates were used as agents for bonding rock sections together and, as the chief component of gels, for filling the pores of artificial rock cores. The purposes of these tests were to find how this substance could be used in the mining industry, for stabilizing fractured ground around mine openings and for sealing off water influx into …

A Study Of Re-Evaporation Nuclei, Ronald Dawbarn

Masters Theses

"Classical considerations of the evaporation of a homogeneously nucleated droplet in an atmosphere of low humidity, indicates complete evaporation of the drop. Experimental results however, show that there is left behind a residual nucleus that is quite stable. Condensation occurs on these nuclei at comparatively low supersaturations. Using a specially instrumented cloud chamber, experimental procedures are described which attempt to investigate some of the properties of these nuclei. Various possibilities causing this stability are examined and compared to the experimental results obtained"--page [ii].

The Dielectric Properties Of A Synthetic Fluor-Mica Formed By Glass-Ceramic Fabrication Techniques, Ray Fred Schumacher

Masters Theses

"A tetrasilicic fluor-mica, K₂Mg₅Si₈O₂₀F₄, was synthesized, utilizing glass forming techniques and subsequent heat treating of the mica glass. Discs, approximately two inches in diameter, were formed and heat-treated at selected temperatures between 700⁰C. and 1150⁰C. for various time periods. Density change, weight loss, shrinkage, and dielectric properties were measured to determine the characteristics of this material"--Abstract, page ii.

The Effect Of Copper Upon The Eutectoid Reaction In The Zinc-Aluminum System, Paul Theodore Corcoran

Masters Theses

"A Leitz dilatometer was used to study the kinetics of the eutectoid reaction in the zinc-aluminum system and the effect of small additions of copper upon this reaction. Three alloys were investigated: a pure 78% zinc - 22% aluminum alloy; a 78% zinc - 21.9% aluminum - 0.1% copper alloy; a 78% zinc - 21% aluminum -1.0% copper alloy. It was found that this reaction was similar to the pearlite reaction in the iron-carbon system. The reaction occurred by diffusion processes and the products of the reaction looked similar to pearlite when examined under the microscope. Copper was found to …

An Evaluation Of The Feasibility Of Neutron Microradiography, Maynard L. Arment

Masters Theses

"The metal working industry has used metallography and microradiography extensively in the past decade. X-ray or gamma microradiography has several advantages as compared to metallography, but a disadvantage concerning alloys of adjacent elements; microradiography cannot distinguish between elements 2 or less atomic numbers apart. Attempts were made using neutron microradiography to distinguish between cadmium and tin rich grains. A maximum resolution of 0.017 inches was found with a calculated possibility of a resolution less than 0.002 inches"--Abstract, page ii.

Coprecipitation Of Metal Salts With Organic Coprecipitants, Omar E. El-Arini

Masters Theses

"Coprecipitation studies were carried out for the more insoluble salts of six common metals and five anion systems. Three metal sulfides, namely, CuS, CdS and NiS, were the only metal salts studied that indicated nearly complete coprecipitation with phenolphthalein as carrier precipitate. The same salts showed almost no coprecipitation with B-naphthol as carrier precipitate. Solvent extraction of CuS with chloroform showed no significant amount of extraction had taken place. The data obtained in this work did not disclose any relationship between the extent of coprecipitation and the solubility product constant of the salt present. The main difficulty encountered at this …

Geochemical Prospecting For Copper In The Northern Part Of Yuma County, Arizona, Abdul Razak Kasim Al-Hashimi

Masters Theses

"Geochemical prospecting for copper has been carried out in two selected areas in the northern part of Yuma County, Arizona. These areas have a few old copper mines and some other zones of mineralization. The rocks of the area range in age from Precambrian to Quaternary and consist of complex gneiss, lava flows, schists, marble, sandstone, conglomerates and some intrusive dikes. A cold-extractible [sic] field method was used to study the relation between the copper content of stream sediments in washes and the geology, mineralization, and topography of the areas. A few total copper tests were also carried out. Another …

Free Convection Heat Transfer From An Inclined Heated Flat Plate In Air, Shu Chien Yung

Masters Theses

"An experimental investigation has been performed to determine the free convection heat transfer from a heated flat plate in air moved from the vertical position through three inclined positions to the horizontal position. The hot surface of the plate was facing downward for the horizontal and three inclined positions. Tests were performed at plate surface temperatures from 120°F up to 404°F. Data for the plate surface temperature at about 165°F with the plate in the vertical position agrees very well with previous experimental work. This same data was used to determine a new parameter, introduced into the Pholhausen free convection …

A Parameter Perturbation Technique Applied To Multipoint Iteration Functions For The Solution Of Systems Of Nonlinear Equations, Robert N. Delozier

Masters Theses

"The convergence of classical iterative procedures, when applied to a system of nonlinear algebraic or transcendental equations, is highly dependent upon a good initial approximation to the desired roots. Most of the classical iterative schemes have convergence factors between one and two. In this paper iterative schemes of order two and greater are studied in connection with a parameter perturbation process. The parameter perturbation process relaxes the restrictions on the choice of initial values. The procedure divides each problem into a number of subsidiary problems. Each subsidiary system of equations is then solved until a solution is found to the …

The Shear Graph And Cohesive Soil, Charles Rees Nickerson

Masters Theses

"Some existing test procedures for measuring shearing properties of soils are reviewed. the correlation between the shear strength of two fine-grained soils as indicated by the unconfined compression test and the shear graph test is investigated. This is accomplished by comparing the test results at varying moisture contents and dry densities. One of the soils used is a red plastic clay, the other a silty clay. The test results indicate that for soils wet of optimum the shear graph strength can be taken as being equal to the unconfined compressive strength. This will be conservative for soils that exhibit an …

Near Optimal Sequencing :N Jobs And M Machines; All Jobs To Be Processed Through The Same Order Of Machines, Larry Glen Clark

Masters Theses

"There is a need, in industry, for an efficient method of determining an optimal sequence for processing a number of jobs through two or more machines. A method which requires a minimum amount of time would be most beneficial. The purpose of this study has been to define such a method. Tests on the method described indicate that although an optimal solution is not always obtained, the solutions obtained are quite good and due to the time factor the method would be beneficial to industry"--Abstract, page ii.

Comparison Of Methods To Select A Probability Model, Howard Lyndal Colburn

Masters Theses

"A comparison is made between the estimates of the parameters in a gamma distribution obtained by the method of moments with those obtained by a numerical approximation to the maximum likelihood estimates. The estimates obtained by the numerical approximation had a smaller mean squared error from the true value than the estimates obtained by the method of moments. Modifications to tests of fit are made in order to develop methods to select a distribution from a set of possible distributions for a population with an unknown distribution. These selection methods are compared in their ability to make correct selections. Although …

A Study Of The Piezometric Surface Of The Grand Falls Formation In The Duenweg-Oronogo Mining Belt East Of Joplin, Missouri, Renny Roger Nichols

Masters Theses

"The Joplin area of Missouri, which includes the Duenweg-Oronogo belt, was a famous zinc and lead mining district. Many mines were abandoned after World War I and filled with water. These provide a large potential supply of ground water. Expansion of industries and population in the area since World War II has caused a demand for water. In 1964, the Ground Water Branch, Water Resources Division, of the United States Geological Survey began a project to study the surface and ground water resources of the area. As part of his work on this project, the author measured the piezometric level …

Radiation Induced Polymerization Of Methyl Methacrylate, Ko-Hung Liu

Masters Theses

"A study has been made of the gamma radiation effect on the rate of polymerization of methyl methacrylate monomer, and also to determine the effects of the presence of clay of known composition and of other solids on the rate of polymerization. The results indicate that the monomer undergoes polymerization and then degradation as a function of radiation time at a given gamma flux"--Abstract, page ii.

Taxonomic Study Of Fossil And Recent Otoliths Of Certain Cuskeels, Gary Neal Pointer

Masters Theses

"Otoliths are calcareous structures occurring in the auditory labyrinths of teleost (bony) fishes. Three pairs of these earstones normally are found: the sagitta, in the sacculus; the asteriscus, in the lagena; and the lapillus in the utriculus. In fishes other than the Order cypriniformes (carp, catfishes, and related forms), the sagitta is the largest otolith, and it may be used in taxonomic and other studies. Fossil earstones of cuskeels (Family Ophidiiae-Brotulidae), constituting the Preophidion complex, occur in relative abundance at various levels in the Claiborne, Jackson, and Vicksburg groups of the Lower Tertiary on the Gulf Coast. The present study …

Temperature Distribution In Thermal Boundary Layers (In Free Convection) Using A Modified Schlieren Method, Philip Ling Chen

Masters Theses

"A simple optical apparatus, the Schlieren interferometer, was constructed for the quantitative investigation of free convection heat transfer from solid bodies. The photographic results, checked by using thermocouples, were used in evaluating the temperature distribution, the key to the solution of these problems. Interpretation of the photographic results was made using the simple calculation for the conventional interferogram and the Dale-Gladstone law. Although the experiments were limited to a heated flat plate and a heated wire, two dimensional test pieces of irregular configuration can be investigated by the same apparatus with simple modifications. The photographs of the conventional Schlieren, the …

A Study Of Stereotype Perceptions Of Northern And Southern College Students, G. Lance Gilbert

Masters Theses

No abstract provided.

A Study Of The Preparation Of Student Teachers For The Use Of The Instructional Materials Center In The Buzzard Laboratory School, Virginia Hagebush

Masters Theses

No abstract provided by author.

The Effect Of Varying Sea Coal Fineness On Sea Coal Activity In Molding Sands, Laurence A. Cooley

Masters Theses

"An experiment was conducted in an attempt to establish a relation between sea coal activity in a facing sand and the particle size of the sea coal added to the sand. It was felt that if a sufficient difference in distribution of volatiles was detected, a correlation between particle size and activity of the sea coal within the test specimens might be established. The lack of positive evidence to support such a relationship is indicative that a variation in particle size does not promote volatile re-deposition within the range of particle sizes investigated for the particular weight per cent of …

Geology Of Pride Mine And New Standard Mine Area, Northwestern Yuma County, Arizona, Henry E. Fernandez

Masters Theses

"A thick section of presumably Precambrian gneiss with thin intercalated bands of marble and schist has been mapped. There is structural continuity within these rock types as they are mutually intercalated, conformable, have gradational relations and show equal participation in the same individual fold. The layers of schist and marble in the gneiss can be followed over long distances. These rocks have undergone intense regional metamorphism, primarily dynamic, with a possible regional compressive force generated from NW-SE giving rise to sets of folds and faults in the area. From structural, petrographic and field evidence, it is concluded that the metamorphic …

Finite Difference Solution For Triangular Plates, Hao-Yang Huang

Masters Theses

"In this thesis the finite difference method is used to solve triangular plates with uniformly distributed transverse load. As a matter of convenience triangular coordinates are used. The supporting conditions as well as the shape of plate are varied. All calculations are performed by digital computer. The patterns of differential operators in triangular coordinates, the deflections of plates, and the moment distributions are shown and discussed. The results obtained for some special cases are compared with published solutions"--Abstract, page i.

Operating Characteristics Of A Cloud Chamber Suited For Condensation Measurements, Donald L. Packwood

Masters Theses

"It is the main purpose of this research to investigate the validity of using the adiabatic laws to determine the temperature from the pressure ratio. Some of the effects which might invalidate the use of the adiabatic laws will be studied. Special consideration will be given to the accurate calculation of [gamma]. Carstens' approximate calculation of the heat flow into the chamber due to conduction will be checked. A measurement will be made of how long the chamber remains adiabatic after an expansion when the continuing expansion technique is used. The static temperature gradient throughout the chamber will be measured …

Linvill's Model As Applied To P-N Junction Photo-Diodes, Rudy Michael Chittenden

Masters Theses

"The problem undertaken in this study is to present a performance evaluation of Linvill's model as it pertains to the p-n junction photo-diode. The evaluation is performed by comparing the distributed mathematical solutions, the solution obtained using Linvill's lumped model, and the experimental measurement of the transient voltage rise across a photo-diode due to a unit-step pulse of light incident on the junction. Despite the absence of a suitable light source for use in the experimental measurement, it is concluded that Linvill's model provides an excellent means to determine the risetime of a photo-diode. This is provided that the photo-diode …

Heat Transfer Coefficients Across Bonds And Contacts, Eugene Charles Fadler

Masters Theses

"The purpose of this investigation was to experimentally determine heat transfer coefficients across interfaces, including the effects of the thermal conductivity of the adherends, the hardness of the adherends, the bond thickness, and the type of adhesive.

Aluminum alloy, steel, copper, and extruded nylon rods were used as adherends; all 1.875 inches diameter and 8 inches long. Each was cut radially at its midpoint and faced off to the desired surface finish. Bare interface tests were conducted before the adherends were bonded together. The adhesives used were high grade silica refractory cement, two-part epoxy resin adhesive, and thermosetting synthetic rubber-phenolic …