Digital Commons Network^™

Transpiration Cooling Of A Porous Plate, Stephan A. Sayegh

Masters Theses

"Transpiration cooling has long been known as an effective way of removing heat from porous materials. This thesis is a new approach to one of the problems of transpiration cooling in the steady state.

The specific problem considered here is that of a uniform porous plate through which a liquid is forced. This liquid vaporizes at a short distance from the surface through which it is forced and leaves the porous plate at the other surface which is exposed to hot gases. It also protects the hot surface by forming an insulating layer between that surface and the hot gases. …

Linear Feedback Control System Compensator Design Under Specified Constraints, Keikhosrow Irani

Masters Theses

"The purpose of this thesis is to find the necessary and sufficient conditions for the design of compensators, following the concepts developed by Ross, Warren, Hsu and Sanden.

The main object that motivates this investigation is to design the lead or lag compensator networks for a given linear feedback system when there are these constraints.

1. Gain of the system is constant.
2. The steady-state error is invariant.
3. The dominant poles of the closed-loop transfer function are specified.

Consideration of the problem is in two parts:

• a. Derivation of necessary and sufficient conditions of compensator design that fulfill the three constraints.
• b. …

Analysis Of Flat Plates By Reaction Distribution Method, David D. W. Yang

Masters Theses

"This study was made to analyze rectangular flat plates by the method of Reaction Distribution and to compare results obtained by this method with that of other methods. The basic approach is to divide the plate into an equivalent grid system and introduce temporary supports at the intersecting joints. The results from this study shows that the Reaction Distribution method is useful in a qualitative analysis of the behavior in a plate but is less satisfactory in obtaining reliable quantitative results"--Abstract, page 2.

Stylolites And Sedimentary Structures In The Cave-In-Rock Fluorspar District, Southern Illinois, Won Choon Park

Masters Theses

"This thesis deals with stylolites, slump structures, sulfides in the oolitic limestone, and geometry of the bedded fluorite deposits in the Cave-In-Rock fluorspar district, southern Illinois. Stratigraphic zones studied were: 1) the upper part of the lower Fredonia limestone member, 2) the upper part of the upper Fredonia limestone member,,and 3) the upper part of the Renault formation.

Geometry of the ore rocks and related structures was investigated. Most of the ore is layered and constitutes part of the sedimentary strata.

Slump structures were observed and studied in detail. Most of the slump structures show evidence which indicates a sedimentary …

Mechanics Of The Voussoir Arch As Applied To Block Caving, Christopher Haycocks

Masters Theses

"The theories of ground failure in massive rock with special reference to the problem of the mechanics of block caving were studied and evaluated.

The mechanics of arch or dome formation underground were studied quantitatively using the Voussoir arch theory. The effect of shear stress on the arch stability was considered and found to affect the system only when the arch height increased beyond certain limits.

A theory of the mechanism of ground failure in an undercut block using the dome theory was advanced. Photo- elastic model studies were used to support the conclusions reached"--Abstract, page i.

Experimental Stress Analysis Of Bolts In A Flange Coupling, Vijay Rastogi

Masters Theses

"In this investigation an attempt has been made to determine simple formulae leading to a better, more useful and much safer design of flange coupling bolts. The bolts were tested under tensile loading and bending and hence the results obtained apply for bolts under these modes of loading only.

The behavior of flange bolts under different initial tightening torques was studied by measuring strains in a bolt on which strain gages had been attached* . From this, the load producing separation of flanges, under different tightening torques, was determined and used in deriving formulae for prediction of the load for …

A Study Of The Permeability And Separation Of Carbon Dioxide And Hydrogen By Gaseous Diffusion Employing Barriers Of Polystyrene, Carl J. Wallace

Masters Theses

"The purpose of this investigation was to study the permeability and separation of carbon dioxide and hydrogen by gaseous diffusion employing barriers of polystyrene. The offset of temperature and barrier thickness on the permeability and separation of carbon dioxide and hydrogen wore Investigated for barriers of one, three, and five-mil thicknesses and for temperatures of 26, 35, 45, and 50 degrees centigrade.

With an increase in barrier thickness of one to five- mils, the permeability of carbon dioxide decreased to one-fourth of its value at the one-mil thickness. The hydrogen permeability decreased to approximately two- thirds of its value at …

Neutron Flux Mapping Of The Msm Reactor, Cary Chow-Yuen Chen

Masters Theses

"This investigation presents a mean to determine thermal neutron flux of a reactor by irradiating copper wires inside the fuel elements. The activity recorded after decay correction, is the relative thermal neutron density. Thermal neutron flux is a measure of the neutron density at thermal energy, 0.025 ev.

Gold foils irradiated at National Bureau of Standards were used as the absolute neutron flux calibration standards. The average flux of the reactor with water as the reflector ranges from 7.24 x 10¹⁰ neutrons/cm² - sec. to 7.87 x 10¹⁰ neutrons/cm² - sec. as obtained from the calculations. …

A Study Of Placer Tin Materials From Southern Thailand, Somkiat Ganthavee

Masters Theses

"This thesis deals with a series of investigations of placer tin samples from a Chinteik's Tin-dredge, Gnaw District, Ranong Province, and the Tin-Pet mine, Phang-gna Province, in southern Thailand.

A brief summary of the geography and geology of Thailand as a whole has been given as a general introduction to the source of the materials studied in this thesis.

The results of sieve analyses have shown that the sluice boxes do not effectively concentrate the cassiterite grain below 0.147 mm. from the rough concentrate treated in the tin-dressing shed.

It has been found that roundness and shape determinations of quartz …

The Removal Of Sub-Structure From Alpha Uranium, Albert E. Bolon

Masters Theses

"The possibility of obtaining larger, perfect single crystals of alpha uranium by a modified strain-anneal method has been investigated. A -196°C tensile deformation was performed on pseudo single crystal rods which had been prepared by the phase transformation method. The specimens were subsequently annealed at 650°C.

It was found that by utilizing pseudo single crystals with a prescribed crystallographic orientation with respect to the tensile axis that recrystallized crystals of comparable size and perfection to those prepared by the grain coarsening method could be produced. Grain coarsening is the presently accepted process for preparing perfect single crystals of alpha uranium. …

An Investigation Of Lehmer's Method For Finding The Roots Of Polynomial Equations Using The Royal-Mcbee Lgp-30, James W. Joiner

Masters Theses

“The solution of the general polynomial equation f (x) = O, where f(x) = a_nxⁿ + a_n-1x^n-1 + … + a₁x = a_o, has received the attention of many mathematicians for hundreds of years and is at present in a very highly developed state. Even a cursory examination of the literature will reveal many volumes on this subject. However, this study is concerned primarily with the numerical methods for solving polynomial equations, hence the classical methods will be treated here only as they contribute to this field.

Virtually all of …

Thermal Conductometer For Liquids, Yuan-Kai Chang

Masters Theses

"The published data pertaining to the thermal conductivity of liquids are of such a character that it is very difficult to determine from them the correct value, or the temperature coefficient for any liquid.

Most of the published values of thermal conductivity for liquids are evaluated at one particular temperature. It is the purpose of this investigation to design, construct and calibrate a thermal conductometer for liquids over a temperature range of 30°F to 200°F.

Since water and glycerol were the only liquids found by this investigator with published data on their conductivities as a function of temperature, they were …

Syntheses And X-Ray Investigations Within The System Fes₂-Cos₂, Samuel Shu Mou Chan

Masters Theses

"Pyrite (FeS₂), cattierite (CoS₂), and various transitional members of the solid solution compounds were prepared. The methods used are as follows:

First, sulfides of cobalt, iron, or cobalt-iron were obtained by precipitation from a mixture of the cobalt chloride and/or ferrous sulfate in an aqueous solution. The dried precipitates were then mixed with an equal weight amount of sulfur and placed into silica glass tubes. After evacuation, they were filled with hydrogen gas of 3/4 of atmospheric pressure and sealed. The samples were then heated up to 500°C (for FeS₂), 650°C (for FeS_{2 …}

Electrodeposition Of Antimony From Sulfide Melts, Mahendra N. Rana

Masters Theses

"A study of the current-potential relationships, and the electrodeposition of antimony metal was conducted for fused mixtures of Sb₂S₃-Na₂S, Sb₂S₃-Sb and Sb₂S₃-NaCl-KCl in the temperature range of 700° - 900°C. An attempt was made to determine the mutual solubility of molten antimony and Sb₂S₃-Na₂S melts. The microstructure of deposited metal was studied metallographically. Analysis of phases present in the matte mixture (Sb₂S₃-Na₂S) was made by x-ray diffraction patterns.

All investigations were carried out in …

A Survey Of The Influence Of Selected Sulfides On The Thermal Decomposition Rate Of Zinc Sulfate, L. G. Twidwell

Masters Theses

"The influence which ZnS, CdS, Cu₂S, PbS, and FeS has on the thermal decomposition rate of ZnSO₄ was studied by measuring the SO₂ gas evolved per unit of time for various ZnSO₄-MeS mixtures at 600°C, and analyzing the solid phases by means of X-ray diffraction patterns.

The SO₂ gas evolved upon heating the pellets was analyzed as a function of time by absorbing the gas in a solution of distilled water, H₂O₂, and NaOH, and measuring the time required for the SO₂ to neutralize the NaOH. The gas …

Preliminary Investigation Of The Effects Of Seeding Fusion Cast Refractories, Thomas Spencer Montgomery

Masters Theses

"The crystallization process in a zirconia-alumina- silica melt of high viscosity was studied, A system was used of the same composition found in commercial electrocast glass tank refractories. Artificial nucleation was tried in an attempt to control the process of crystallization; the method involved the addition of suitable "seeding" material.

It was found that introduction of nucleation agents consisting of the major component oxides of the system had noted effect upon the course of crystallization. Preferred orientation normally found in unseeded electrocast refractories was diminished with the addition of zirconia grains and amplified with particles of tabular alumina.

Results obtained …

Analog Study Of Vibratory Forces In Sorting Machine, Navnit Chhaganlal Mehta

Masters Theses

"This investigation involves the study of the reduction of vibratory forces in a sorting machine. The equivalent masselastic system is shown in Figure 1, in solid lines. In this figure the mass m₁ represents the main structure for the mounting of the machine, the mass m₂ is the main bearing blocks and the mass m₃ is the vibrating basket. The elastic stiffness indicated as k₁ represents the mounting spring for the entire unit, the stiffness k₂ is that of the beam structure by which the bearing block is attached to the main structure, and the stiffness k₃ is that of …

Effect Of The Mixed Liquor Suspended Solids Concentration On The Treatment Of Dairy Wastes By Activated Sludge Process, Meredith Hambleton Saxer

Masters Theses

"The effect of the mixed liquor suspended solids concentration on the treatment of dairy wastes by the activated sludge process was investigated to provide original and basic information of value to the waste water treatment field.

The studies were conducted using a continuous flow activated sludge laboratory unit. Two different synthetic dairy waste systems were used in this investigation, the 0.05 Percent Skim Milk Waste System and the 0.1 Percent Skim Milk Waste System. These wastes provided BOD loadings of 43.9 and 91.1 lb. BOD per day per 1000 cu. ft., respectively, at the 12 hour detention period employed. Mixed …

A Survey Of Current Techniques For Selecting First-Line Supervisors In Industry, Linford A. Sutherland

Masters Theses

Introduction

The purpose of this investigation is to show to what extent the selection of supervisors is still based on subjective opinion, and to what extent objective devices have been developed and have gained acceptance.

The collection of relevant data for this survey involves a search of the published literature in the field. In this work the terms first-line supervisor, foreman, and supervisor will be used interchangeably.

The writer's interest in the area of supervisory selection was aroused after reading several articles on the problem of selecting factory supervisors of the highest caliber as industry now realizes that the supervisory …

A Study Of The Application Of Science And Mathematics In Industrial Arts, Jack David Fox

Masters Theses

I. Purpose of the Study

The purpose of this study was to ascertain the extent to which the applications of science and mathematics were being taught in industrial arts courses in the schools of Michigan, and to show what, if any, similarities or differences existed between the applications being taught and (1) the size of the school, (2) the type of shop, (3) the grade level, and (4) the degree held by the instructor.

More specifically data were gathered to ascertain:

1. The college preparation in science and mathematics received by the industrial arts instructors.

2. The extent to which …

The Building And Establishment Of Washington, 1788-1809, Robert C. Harris

Masters Theses

Preface

The following research concerns the beginnings of our national capital. Of the people who have contributed to its development, many were Americans, while others were immigrants striving for freedom in their newly established nation. To all the most important task was to find a permanent site for their national capital.

Millions of Americans have visited Washington, D. C. since 1800, leaving their beloved city with diversified ideals for its future. Dr. H. Paul Caemmerer has several quotations from famous American personalities regarding the national capital.

Art Education And Appreciation: A Syllabus For High School Teaching, Max I. Briggs

Masters Theses

No abstract provided.

An Analog Method For The Determination Of The Deflection Of Beams Resting On End Supports And Design Of An Automatic Programming Device, Paul C. Jackson Jr.

Masters Theses

"This investigation shows that beam problems can be solved easily and accurately with an analog computer. Two problems were solved as to their shear, moment, slope and deflection along the length of the beam and the graphs drawn by the analog computer were compared with calculated values. Very little difference was found between them.

An electronic programmer was built to aid in handling beam problems as they were being run on the computer. This was capable of putting into the computer bits of data at specified intervals of time. The programmer proved reliable and repeatable once it was adjusted to …

Impact Energy Coupling And Impact Seismic Refraction Using Electronic Timing, Roderick D. Carroll

Masters Theses

"The use of impact energy sources in lieu of explosives for shallow seismic investigations is limited chiefly by the low energy available. Means of increasing the energy transmission of an impact source are investigated, using a weight drop arrangement and an oscilloscope. The energy of refracted arrivals is investigated by direct overburden impacts, compaction of the overburden at the point of impact and the use of steel and aluminum plates as coupling devices. Energy transmission is shown to be greatly increased, using a suitable coupling device and the conditions for optimum coupling are discussed. The elastic constants of the ground …

The Effect Of Phosphoric Acid On Compaction And Shear Characteristics Of Pure Kaolin Clay, Bhupat Hargovinddas Mehta

Masters Theses

"The work presented is the investigation of the effect of phosphoric acid on the compaction and shear characteristics of pure kaolin. Pure Georgia kaolin clay average particle size of five microns was mixed with different percentages of phosphoric acid. These mixtures were permitted to react for varying periods of time. The results of the study indicate a notable and gradual increase in dry density of the kaolin with increasing percentages of phosphoric acid admixture. The acid admixture ranges from one up to nine percent of the dry weight of the clay. Increase in cohesion of the clay with increase of …

Underground Methods Of Working Coal, Hemendra Nath Datta

Masters Theses

"'Underground Methods of Working Coal' is the subject of this thesis. It is the purpose of this investigation to summarize all the mining methods under various conditions of working.

The underground methods of mining have been classified under three headings; viz., (a) Room and Pillar, (b) Longwall and (c) Horizon Mining. The conditions suitable for the applicability of each system and their relative merits and demerits are fully discussed.

The principles of the design of the workings of both room and pillar and longwall systems to have effective roof control in the area of the workings are pointed out.

Distinct …

A Resistivity Study Of Hot Short Ferrous Alloys, Harold Alfred Koelling

Masters Theses

"Resistivity measurements were performed at elevated temperatures on four special ferrous alloys and one commercial iron. The alloys were pure iron, iron with .023 per cent sulfur, iron with .33 copper, iron with .32 copper and .024 sulfur. Other elements were held to the minimum amounts possible in order to determine the actual effects of sulfur and copper. The commercial alloy was Armco Iron.

Measurements of resistivity versus temperature were taken at slow heating rates to determine if the iron sulphide liquid film formed in the grain boundaries of red-short steels had any effect on the electrical resistivity"--Abstract, page 7.

A Study Of The Difference Effects On Alpha Solid Solutions Of Oxygen In Titanium Dissolving In Hydrofluoric Acid, Kuo-Chin Chuang

Masters Theses

"Alpha solid solutions of oxygen in titanium dissolving in hydrofluoric acid exhibited a positive difference effect with k values of 5.7, being independent of the concentration of HF, within the compositional range studied 0 to 5 w/o oxygen. This indicates that various TiO_x alloys are polarizable to the same extent by the same strength of anodic current in hydrofluoric acid.

The difference effect observed on TiO_x alloys dissolving in HF-HCl revealed that the effect is dependent on the oxygen content of the solid solution as well as on the concentration of HCl. The presence of HCl results in …

A Study Of The Hood Inlet And Its Possible Use As An Overflow Structure For A Sanitary Lagoon, Richard Irwin Boe

Masters Theses

"A closed conduit, such as an overflow pipe for a conservation pond or a sanitary lagoon, will not flow full if laid on a slope that is hydraulically steep unless the pipe entrance receives special attention. A steep conduit slope is necessary to insure that the pipe entrance controls flow.

The recently introduced hood inlet will permit the closed conduit to flow full, even if on a hydraulically steep slope, upon a slight submergence of the inlet crown. The hood inlet is formed by cutting the pipe at an angle so that the crown of the inlet projects beyond the …

Tank Studies Of The Resistivity Horizontal Profiling Method Of Electrical Prospecting, Edward Hornsey

Masters Theses

"This research project was undertaken to perfect a technique whereby theoretical horizontal resistivity profiles could be reproduced in laboratory tank studies.

Several specimen materials were tried and finally an acceptable specimen material was found. It was found that carbon specimens suspended in salt water would give horizontal resistivity profiles that agree to a remarkable degree with the theoretically predicted curves.

The investigations showed that the depth of burial of the specimen has a marked influence on the position of the characteristic edge effects and on the magnitude of the apparent resistivity.

The studies also indicated that successful tank studies could …