Digital Commons Network^™

Isotope Effect Of Interstitial Diffusion Of Carbon In A Dilute Fe-Si Alloy, Edward T. Yen

Masters Theses

"The isotope effect of carbon interstitial diffusion in a Fe-2.75at%Si alloy has been measured at -3.10°C using the disaccommodation technique. The disaccommodation has been analyzed in terms of two relaxation processes which are discussed on the basis of the reorientation mechanism of carbon interstitials at Fe-Fe sites and Fe-Si sites respectively. The ratios of the relaxation times [tau]₁₃/[tau]₁₂ are 1.0382 for the former and 1.0072 for the latter relaxation process. This result is discussed on the basis of many-body reaction rate theory"--Abstract, page ii.

Analytical And Experimental Methods For Determining The Properties Of Materials At Very High Rates Of Loading, A. G. Behring

Masters Theses

"In the following report, some of the properties of ALCOA 7075 T651 aluminum, when subjected to high rates of loading, are experimentally investigated by impacting two rods of the material longitudinally. One rod is accelerated to a uniform velocity with an air gun launcher. The stationary second rod is instrumented with strain gages on its lateral surface in order to determine the strain-time history following impact. A detailed description of the experimental equipment is included. Simple, one-dimensional theory is used to determine the dynamic, elastic modulus of the test material under the impact condition. Several observations regarding the behavior of …

The Design Of A Hybrid Computer System, James Joseph Becker

Masters Theses

"Three typical hybrid computers in industry and educational institutions are presented. The hybrid computer designed and built at the University of Missouri at Rolla consists of an SCC-650 digital computer, a TR-48 analog computer, and a hybrid interface. The interface permits the digital computer to control the modes of operation on the analog computer. There are also 9 multiple-pole relays on the interface that can be controlled by the digital computer. A 320 hold removable patchboard is included in the interface. There are 40 trunks lines from the analog computer that are present on the patchboard. The 4 digital-to-analog channels …

The Design Of A Tape Deck Controller, Frederick Harold Keeve

Masters Theses

"A controller was built to interface the SCC-650 general purpose digital computer and the Kennedy Model 1400R incremental write/continuous read tape unit. All logic design information, signal lists, and tape deck instructions are included"--Abstract, page ii.

Construction Time And Cost Control Using The Ibm Project Management System/360, James Donald Bailey

Masters Theses

"The object of this investigation was to determine the advantages or disadvantages involved in the use of the IBM Project Management system/360 as a time and cost control tool as compared to the methods presently used by construction contractors in the small to medium size range.

The methods used by three construction contractors were investigated in order to acquire a sample of methods presently used.

It was determined from the investigation that a number of advantages could be obtained which would provide better control of a construction project.

It was also decided that a detailed investigation concerning the cost of …

The Effects Of Grinding On The Physical Properties Of Clay Soils, Thomas Michael Mcmillen

Masters Theses

"Studies of the effect of grinding on clay soils are summarized. Fundamental aspects of thixotropic phenomena are also explored. Vetters clay and Lebanon silt loam are used as test soils. these soils are ground to varying degrees and the deviations in physical properties are determined. Atterberg Limits, specific gravity, grain size, X-ray diffraction, and D.T.A. tests are run on each soil batch (ground for 0 minutes, 30 minutes, 60 minutes, and 120 minutes). A thixotropic study, consisting of unconfined compression and laboratory vane shear tests, of each soil batch is made. The results of the tests are analyzed, compared, and …

A Fluidic Liquid Level Control System, Vinod Kumar Verma

Masters Theses

"The prime objective of this investigation was to design and construct a working "Fluidic liquid level control system", and to make a functional study of the characteristics of the devices employed therein. A working model of a "fluidic liquid level control system" is developed and experimental data is collected to describe the functional characteristics of the fluidic circuits employed. The system contains a pressure sensitive, variable frequency oscillator; appropriate demodulation stages to convert the variable frequency alternating signal into a varying non-alternating signal; and on-off control elements in the final stages"--Abstract, page ii.

The Density Of Horizontal Control In Missouri, Norman Lee Brown

Masters Theses

"In 1965 the Missouri Legislature passed House Bill 201 adopting the Missouri Plane Coordinate System as computed by the United States Coast and Geodetic Survey. The requirements of this law and the density and distribution of usable control within the state is the topic of this thesis"--Abstract, page ii.

The Influence Of Silt On The Compressibility Of An Illitic Clay, James Inman Spencer

Masters Theses

"This study was undertaken to investigate the effect of varying amounts of clay (illite) on the compressibility of a silt as it may be found in nature in a normally consolidated deposition. Laboratory procedure was designed to minimize sample disturbance so as to obtain, as nearly as possible, a virgin consolidation curve. By varying the amounts of silt and clay in a given sample, and sedimenting the sample from a soil-water suspension, consolidation test analyses were used for a comparison of the various samples. Results revealed that between sample mixtures of 40 and 60 percent silt there was a relatively …

The N-Wire Exponential Transmission Line, Vernon Ray Stanley

Masters Theses

"This paper deals with the n-wire exponentially tapered transmission line. A characteristic impedance is defined, and the results of terminating in this impedance are investigated. A very long line and the condition of no reflections are considered, and the conclusions are compared. Finally, three specific 3-wire line problems are worked with a characteristic impedance termination and a unit step input"--Abstract, page ii.

Corrosion Rates And Electrokinetics Of Cobalt And Cobalt-Rich Cobalt-Iron Alloys In Sulfuric And Hydrochloric Acids, Cheng Tzong Horng

Masters Theses

"Corrosion rates for Co and Co-rich Co-Fe alloys were determined in sulfuric and hydrochloric acids under both deaerated and oxygenated conditions. For the purpose of comparison, corrosion rates of Co cut from metal sheet were also determined in the same environments as those of sintered alloys. Sintered alloys were inferior to solid Co as corrosion resistant materials. It was found that the surface was more corrosion resistant than the interior. Thus after long exposure to the corrosive acid, the samples became porous inside while the surfaces remained substantially intact. Oxygen had a pronounced effect in accelerating the corrosion of Co …

Zap - A Computer Program To Predict Fission Product Concentrations As A Function Of Neutron Flux, Irradiation And Cooling Times, Bruce Earl Koopmann

Masters Theses

"The development of a computer code was undertaken to calculate the fission product nuclide concentration for spent fuel discharged from a nuclear reactor, as a function of irradiation time, cooling time, neutron flux, and element cross section. The necessary input data was prepared from the basic nuclear data for fission of uranium-235 and plutonium-239. Calculations are also made for total or selective element beta heating and total gamma flux according to user selected input groups. These calculations would be useful in fuel element shielding, cooling, shipping and processing studies"--Abstract, page ii.

Permeability And Additive Sorption And Extraction In Lubricating Greases, Chan-Shan Fan

Masters Theses

"The effect of the area and type of surface of ten silica thickeners and aluminum oxide on grease permeability, on the sorption of PAN [Phenyl-α-naphthylamine] by the grease, and on subsequent extraction were studied. For grease containing 6% per cent of thickener, permeability coefficients varied from 20.1 x 10⁻¹¹ cm² to 168 x 10⁻¹¹ cm². For each silica type they decreased with increase in surface area of the thickener. The level of the permeability coefficient is generally related to the worked penetration. In sorption measurements using permeating oils of varying PAN concentration, the amount of PAN associated with the thickener …

Influence Of Nobler Metal Salt Additions Upon The Dissolution Rate Of Aluminum In Hydrofluoric Acid, Barry L. Basden

Masters Theses

"The rate of dissolution of aluminum in 2N HF upon the addition of nobler metallic salts was studied. Aluminum corrodes in HF due to the acid's ability to dissolve the protective oxide present on the surface. Rates were measured by the hydrogen evolution method. Salt additions of AgN0₃, CuSO₄, HAuC₄, and PtCl₄ to aluminum dissolving in 2N HF resulted in the electroless deposition of more or less coherent metals (from the salts mentioned) on the aluminum surface. The dissolution rate initially decreased in all of the cases and was attributed to the "blanketing effect" of the deposits. Ensuing increases of …

The Analysis Of A Phase-Locked Loop By The Functional Expansion Method, Hugh Francis Spence

Masters Theses

"The time response of a generalized second order Phase-Locked Loop to step and ramp inputs is described by a functional power, truncated at the third order term. The responses given by the functional power series differs from the analog simulation by less than 6% when the inputs are below 2.0 rad (rad/sec)"--Abstract, page ii.

An Unsteady-State Method For Determining The Thermal Conductivity Of Materials, Richard H. Bulmer

Masters Theses

"Originally this work was initiated to develope [sic] a method for measuring the thermal diffusivity and thermal conductivity of metals. Due to the characteristics of the method and the equipment used, it was concluded that the technique is not suitable for materials of high conductivity. However, results show that the apparatus is valuable for the determination of the thermal diffusivity of relatively poor heat conductors. The favorable characteristics of the method are its rapidity and basic simplicity"--Abstract, page ii.

Effects Of Pressure On The Mechanical Properties Of Magnesium, Joseph George Hoeg

Masters Theses

"The data collected in an attempt to evaluate the pressure dependency of the mechanical properties of extruded AZ31B-F magnesium alloy are presented herein. This information was compiled from the results of compression tests run in hydraulic fluid environments pressurized to 50,000 psi, and tension tests run in the atmosphere. Specimen axial load and longitudinal strain were recorded and converted to effective stress and effective strain parameters for presentation. The term pressure is defined, in this report, as the negative average of the principal stresses or, essentially, the negative of the hydrostatic component of stress. The effective stress and strain, at …

Pressure Welding Of Continuously Cast Nodular Iron, Gerald W. Wille

Masters Theses

"The objective of this study was to determine the feasibility of using pressure welding as a joining technique for swaged nodular iron.

Test pressure welds were produced with swaged continuous cast nodular iron at temperatures between 1750⁰F and 2050⁰F with welding pressures between 15,900 psi and 51,400 psi using an induction coil to heat the weld zone.

Pressure welds of greater strength than the as-received nodular iron were produced by swaging the material before welding. The optimum welding parameters were a temperature of 2050⁰F with a welding pressure of 46,700 psi.

On the basis of these tests it is concluded …

Computer Simulation Of Radiation Damage In Fe₃Al, Roland Otto Jackson

Masters Theses

"A computer program, designed to simulate the ordered state of the B.C.C. alloy, Fe₃Al, was used to study the effects of irradiation on an order-disorder alloy. Twenty-six runs were made with this program representing a variety of initial conditions. In all cases, the final damaged state consisted of Frenkel defects, vacancy-interstitial pairs; and the distance separating these pairs was a sensitive function of the energy and direction imparted to the primary knock-on. Both the vacancy and the interstitial were found to be normal, stable defects, with the interstitial residing in a "split"-configuration oriented in the [110] direction. The threshold energies …

Sulfide Mineralogy And Fabrics Of The Iron Ores At Benson Mines, New York, Pedro Hugo TumialáN De La Cruz

Masters Theses

"The occurrence of sulfide minerals and their textural relationships to the silicate and oxide minerals in the Benson Mines, New York, iron deposit were investigated by ore microscopic and petrographic means. The Benson deposit is one in which the dominant iron oxides, magnetite and hematite, occur in a quartz-feldspar gneiss which was subjected to hornblende granulite subfacies metamorphism. Two hundred ore and country rock specimens were systematically collected from all parts of the open pit mine. Polished sections and thin sections were prepared from nearly all of the collected specimens. The oxide ore exhibits a granular texture in which isolated …

Semiempirical Determination Of The Differential Fast Flux Spectrum For U-235 Fission With Water Moderator, Henry Anthony Till

Masters Theses

"The differential fast flux spectrum of the UMR Pool Research and Training Reactor core was determined by simultaneous activations of threshold foil detectors by neutron-nucleon reactions. This represents one phase of the composite neutron environment at two sample irradiation locations and the center of a fuel element during a power operation of 200 Kw (th). To accomplish this measurement a semiempirical least-squares approximation fitting activation date to a theoretical Cranberg U-wet fission spectrum was applied. This is a technique designed specifically for water moderated systems and takes into consideration both virgin and down-scatter neutrons. Gamma decay photopeaks were reduced using …

Diffusion Coefficients Of D-Glucose In Aqueous Carboxymethylcellulose And Carboxypolymethylene Solutions, Audrey Liu-Mei Huang

Masters Theses

"A microinterferometric method was used to determine the concentration profiles in the infinite field unsteady state diffusion of D-Glucose in aqueous polymer solutions. Pseudo binary diffusion coefficients were determined as a function of reduced concentration both with and without the effect of liquid volume change during diffusion being considered. The systems studied were D-Glucose in aqueous Carboxymethylcellulose and D-Glucose in aqueous Carboxypolymethylene solutions. Solute concentration ranged from nearly zero to about 9% by weight D-Glucose in the aqueous polymer solutions"--Abstract, page ii.

Shear Strength Behavior In Silts And Clay Mixtures, Alan T. Jackson

Masters Theses

"A series of consolidated undrained triaxial tests with pore pressure measurements were performed on laboratory sedimented samples having various known silt to clay content ratios. The clay used was commercial grundite clay from Goose Lake, Illinois, and the silt used was extracted from Lebanon Silt Loam from Rolla, Missouri. Silt was mixed with clay in the following percentages by weight: 0%, 20%, 40%, 50%, and 80%. Results indicate an increasing angle of internal friction with an increase in silt content. The unconfined compressive strength of the samples remained constant, as would be expected in a clay, with increasing silt content …

A Computer Adaption Of Plastic Analysis For Rigid Frames, Gerald Duane Galloway

Masters Theses

"A computer program for the plastic analysis of rigid frames is presented. The program is based on the virtual work method of plastic analysis. The great number of failure mechanisms that must be considered in any virtual work analysis are given in Appendix C. The use of the program as a design aid is also discussed. A check for the virtual work program is also presented. The check is based on the method of inequalities as initially presented by Symonds and Neal"--Abstract, page ii.

Coupled Transport Of Heat And Mass In Laminar Tube Flow, Lung-Mau Huang

Masters Theses

"The object of this investigation is to study the mutual dependence of heat and mass transport in laminar and hydrodynamically developed tube flow. Consideration is given to gas flow through a tube whose wall is coated with a sublimable materials so that heat and mass transfers take place between the wall and the flowing gas stream. The tube wall is thermally insulated from the external environment, with the result that the latent heat required by the sublimation process at the wall is supplied solely by convective transfer from the gas. The analysis of the problem requires simultaneous solution of the …

Evaluation Of Methods For Analysis Of Multi-Degree-Of-Freedom Systems With Damping, Brijgopal R. Mohta

Masters Theses

"A general review of various methods for studying the behavior of linear lumped parameter systems with viscous damping is presented. Five methods are discussed. These are: (1) Normal Mode Technique (2) Ho's Method (3) Impedance Method (4) Graphical Technique (5) A Method for Reducing Degrees-of-freedom. For solution of vibration problems by the Normal Mode Technique, the systems are classified as (1) classically damped or (2) non-classically damped. It is shown that the classically damped systems are relatively easy to solve. For non-classically damped systems, the method proposed by K. A. Foss has been employed. This method is quite complex, but …

Measurement Of Demagnetizing Factor Of Ring-Core, Subhashchandra Chimanlal Patel

Masters Theses

"A method has been presented to measure the demagnetizing factor of ring-cores. First the incremental apparent permeability and the incremental true permeability were measured at different degrees of saturation and then the demagnetizing factor was determined from those results. The cores used were tape would ring-cores of mean length of 8.0 cm. The method was found suitable for cores with 1/4 mil or thicker tape, but was in question for the 1/8 mil tape core tested"--Abstract, page ii.

A Numerical (Matrix) Solution For The Vibration Frequencies And Modes Of A Nonuniform Rectangular Plate With Arbitrary Edge Conditions, F. David Utterback

Masters Theses

"The material presented in this thesis is designed to provide the practicing engineer with a practical, approximate method of solution for the increasingly important problem of plate vibrations. The technique presented herein is basically an application of the use of generalized coordinates to describe the elastic and inertial properties of a finite element representation of a nonuniform rectangular plate. The plate will be idealized by utilizing a modification of the grid work technique developed by Hrennifkoff as a lattice work of interconnecting beams. By employing the elastic displacements as generalized coordinates, the only required compatibility conditions are that the displacements …

A Study Of Swirling Air Flow In A Converging Nozzle, Charles William Lineberry

Masters Theses

"A study was conducted to determine the behavior of swirling air flow in a converging nozzle. Special instrumentation was constructed to obtain radial traverses of the flow at four axial positions. the data collected consisted of velocity, static pressure, and stagnation temperature. The flow pattern demonstrated the Ranque-Hilsh effect and reversed axial flow in the core region. As the flow entered the nozzle, it had the characteristics of a free vortex. At the exit plane the characteristics were those of a forced vortex. The converging nozzle caused an increase in the magnitude of the axial velocity component"--Abstract, page ii.

An Experimental Method Of Determining The Thermal Accommodation Coefficients Of Metallic Surfaces, Raymond John Dethorne

Masters Theses

"In the free molecule regime, Knudsen number greater than 10, heat is transferred from a solid by radiation and conduction. The ability of a surface to emit radiant energy is governed by a surface property called emittance while the surface property which apparently regulates the amount of heat transferred by conduction is called the thermal accommodation coefficient. This thesis presents the results of an experimental investigation to determine a relationship between these two properties, emittance and thermal accommodation coefficient. A test apparatus was constructed to measure both the radiation and conduction contributions between two concentric cylinders. cylinders of aluminum and …