Digital Commons Network^™

Assessing Downstream Stormwater Impacts For Urban Watershed Planning, Johanna Meyer Pavlowsky

Masters Theses

"The urbanization of watersheds has caused debilitating effects to downstream aquatic ecosystems in catchments and streams. The implementation of green infrastructure (GI), such as permeable pavements and bioretention facilities, has been shown to alleviate these effects by both reducing runoff and mitigating pollutants; however, the implements are often not designed with a specific goal of water improvement. This study targets understanding a small, impaired urban watershed, and the benefits green infrastructure may have to provide environmental, social, and economic improvement to the watershed.

Portions of Rolla including much of the S&T campus drain into the impaired urban waterbody Frisco Lake, …

Material Properties Affecting The Penetration Of Metal Targets By Copper Linear Shaped Charges, Kevin Lee Phelps

Masters Theses

"A linear shaped charge (LSC) is an explosive device used in demolition, aerospace, and in other applications that require the cutting of metal. Users of LSC's typically know the size of shaped charge needed to cut their target but commonly encounter previously untested materials. The motivation for this thesis is to provide an understanding as to what target material properties are good indicators of cutting performance so the selection of LSC can be more efficient. The author found that penetration theories for other types shaped charges were insufficient for the LSC, possibly because of the relatively slow projectile created by …

Application Of Embedded Frequency Selective Surfaces For Structural Health Monitoring, Dustin Franklin Pieper

Masters Theses

"This thesis proposes the use of Frequency Selective Surfaces (FSSs) as an embedded structural health monitoring (SHM) sensor. FSSs are periodic arrays of conductive elements that filter certain frequencies of incident electromagnetic radiation. The behavior of this filter is heavily dependent on the geometry of the FSS and local environment. Therefore, by monitoring how this filtering response changes when the geometric or environmental changes take place, information about those changes may be determined. In previous works, FSS-based sensing has shown promise for sensing normal strain (a stretching or compressing geometrical deformation). This concept is extended in this thesis by investigating …

Numerical Analysis Of Flexural Slip During Viscoelastic Buckle Folding, Davi Rodrigues Damasceno

Masters Theses

"Flexural slip is considered to be an important folding mechanism contributing in the development of different folds such as chevron, and kink-band buckle folds. Various filed studies have provided a general conceptual and qualitative understanding of flexural slip. However, quantitative evidence of the importance of the flexural slip mechanism during fold evolution is sparse, as the actual amount of surface parallel displacement, and timing, is difficult to measure accurately, due to the lack of suitable strain markers.

In this study 2D finite element analysis is used to overcome these disadvantages and to simulate flexural slip during viscoelastic buckle folding. Variations …

Evaluation Of Ultra-High Performance Concrete (Uhpc) In Joints Of Bridge Girders, Saipavan Rallabhandhi

Masters Theses

"Joints are often considered as the weak link in a structure and often deterioration of the structure initiates from the joints. Joints transfer the stresses from super-structure to sub-structure and in this process are subjected to large transfer stresses. Not much attention is given to the design of joints as they are positioned in low moment regions and typically a 4 to 6 ksi (28 to 41 MPa) concrete is used to fill the joints. One of the solution to this problem is Ultra-high performance concrete (UHPC). In the recent past significant research has been done to use UHPC in …

Data Analysis Of Surfactant-Induced Wettability Alteration In Carbonate Reservoirs, Hao Sun

Masters Theses

"Most carbonate formations prove to be oil-wet due to oil aging effect. Therefore it is essential to employ wettability alteration methods for a more effective enhanced oil recovery process. It is confirmed by researchers that surfactant treatment has positive effects on wettability alteration of carbonate rock, from strong oil-wet to intermediate wet or to even weak water-wet. A number of experiments have the same conclusion and yet, a systematic screening guide development with the support of sufficient data analysis is lacking.

This study involves screening guide development for surfactant-induced wettability alteration method. 199 experiments collected from published literatures are analyzed …

Artificial Neural Network Approach To Predict Blast-Induced Ground Vibration, Airblast And Rock Fragmentation, Raymond Ninnang Tiile

Masters Theses

"Blasting has been widely used as an economical and cheap way of rock breakage in mining and civil engineering applications. An optimal blast yields the best fragmentation in a safe, economic and environmentally friendly manner. The degree of fragmentation is vital as it determines to a large extent the utilization of equipment, productivity and mill throughput. Explosive energy, besides rock fragmentation, creates health and safety issues such as ground vibration, air blast, fly rock, and back breaks among others. As a result, the explosive energy impacts structures and buildings located in the vicinity of the blasting operation, and causes human …

Avon Alkaline Igneous Province, Missouri: Characterization Of Subcontinental Mantle Source And Evolution Via Chemical Analysis Of Olivine, Zachary William Freeman

Masters Theses

"This article presents the crystallization age of, and composition of olivine phenocrysts within an alnoite of, the Avon Alkaline Igneous Province (AAIP) of Ste. Genevieve County, Missouri. The AAIP is an ultramafic igneous province consisting of approx. 80 known intrusives of diverse lithology and texture. ⁴⁰Ar/³⁹ Ar geochronology indicates an emplacement age of 386 +/- 1 Ma, which establishes the AAIP as the only known Devonian-age ultramafic igneous body in the Midwestern U.S. Study of the AAIP provides a unique opportunity to characterize the Devonian-age subcontinental mantle and the processes that generated the suite of ultramafic rocks present …

The Evaluation Of Sequential Optimization And Reliability Analysis, Guannan Liu

Masters Theses

"Sequential Optimization and Reliability Assessment (SORA) has been used for more than one decade for reliability-based design (RBD), but comprehensive theoretical studies on its performance have not been conducted. Further investigations on its performance are still needed. The objective of this thesis is to evaluate the performance of SORA for various testing problems. The performance of SORA evaluated in this thesis includes (1) accuracy, (2) efficiency, and (3) convergence behavior or robustness with numerical testing problems. SORA is evaluated with comparison with other major RBD methodologies. The testing problems are in different scales (numbers of design variables, random variables, and …

Pim Source Identification Using Vibration Modulation Method, Sen Yang

Masters Theses

“In Section 1, passive intermodulation (PIM) is introduced and the mechanism of it is briefly explained. Then, the up-to-date PIM testing and source identification method in the industrial and academia worlds will be summarized.

The vibration modulation method for PIM source identification is proposed in Section 2. Different vibration sources were tested and compared, and the test results showed that the vibration modulation method is able to identify PIM source with good accuracy.

Section 3 outlines a special PIM source identification system built based on the vibration modulation system. The two subsystems, PIM receiver and PIM vibrator, are illustrated in …

Composite Model Representation For Computer Aided Design Of Functionally Gradient Materials, Fangquan Wang

Masters Theses

"Functionally Gradient Materials (FGMs) feature smooth transition from one material to another within a single object. FGMs modeling is considered to be one of the new challenges in Computer Aided Design (CAD) area. To overcome this challenge, this thesis presents a composite approach to model FGMs. The input in STL format can be meshed and voxelized in FGMs modeling system. The material composition in each voxel can be generated from multiple different types of control features. And LTI filters including Gaussian Filter and Average Filter are applied to blur default material features in order to generate FGMs inside models. The …

Low-Head Dams On Habitat, Fish Functional Guilds And Genetic Structuring In A Midwestern River System, Shannon Cassandra Frary Smith

Masters Theses

The natural flow regime of the majority of rivers in the United States has been altered by anthropogenic structures. This loss of connectivity plays a strong role in shaping river ecosystems by altering physical habitat characteristics and shaping fish community assemblages. Although the impacts of large dams on river systems are well documented and often easy to observe, there are fewer studies on the effects of smaller low-head dams. Additionally, the influences of low-head dams on the genetic structuring of small-bodied riverine fishes have yet to be fully explored. I assessed the effects of two low-head dams on the Vermilion …

Demographics And Parasites Of Spotted Bass In The Wabash River, Evan C. Boone

Masters Theses

Spotted Bass Micropterus punctulatus Rafinesque are a popular sport fish primarily found in the streams and reservoirs of the south. The Wabash River, a large tributary of the Ohio River, contains a naturally reproducing population on the northern boundary of their range. Currently, the lower Wabash River is monitored using two different sampling designs, the Long Term Electrofishing Program monitors community assemblages using stratified random sampling whereas the Illinois Department of Natural Resources uses a fixed sampling design. Due to the wide distribution but low abundance of Spotted Bass throughout this drainage, captures from each design were compared to assess …

Factors Influencing Student Major Selection At A Community College, Kellie Jean Keck

Masters Theses

College students are influenced by many different things the moment they arrive on campus. This study was an exploratory study that examined what factors influenced student major selection at a rural Midwestern community college. Qualitative interviews were conducted with (N = 6) sophomore level participants that were previously undecided but had since declared a major. Participants were asked a series of questions about their major selection process including their experiences as an undecided student, who, and what may have influenced their major selection, what role monetary returns played in their major selection, and how comfortable they are with their …

Functionalized Bodipy Dyes For Dye-Sensitized Solar Cells, Mahmoud A. Elkhalifa

Masters Theses

It is predicted that more than 20 terawatts of carbon-free energy will be demanded by 2050 to maintain a sufficient energy supply for the increasing global population, and photovoltaics are predicted to contribute significantly to the global energy needs. Dye-sensitized solar cells (DSCs) are an emerging class of photovoltaics (PV) that has produced promising power conversion efficiencies at low costs. Currently, electron recombination, dye aggregation, weak adsorption, and inefficient absorbance are among of the largest contributors to low DSC efficiencies.

BODIPY dyes are one of the most promising classes of dyes emerging for DSC application. These low molecular weight fluorophores …

Development Of Learning Objectives For An Undergraduate Computer-Aided Drafting And Design Animation Using The Delphi Technique, Gavin M. Wilk

Masters Theses

This study reflects on learning objectives created for an advanced computer aided drafting (CAD) learning module(s) or course with the emphasis on simulation and engineering animations. These objectives were derived by using the Delphi technique by access the support of a panel of subject matter experts (SME) from academia and industry that are interested in CAD. The results of this study are intended for the use of creating instructional modules for undergraduate studies.

A panel of experts were chosen through an electronic listserv of engineering and technology supporters. Two rounds of two different Delphi survey instruments were utilized to complete …

Impact Of Transcription Factors On Fibroblast Specific Gene Silencing In Somatic Cell Hybrids, Tania Ray

Masters Theses

As totipotent cells differentiate to specific cell types in multicellular organisms, certain sets of genes are turned off (gene silencing/gene extinction) while others are turned on (gene activation). Cell type specific gene silencing and gene activation is the basis of cell differentiation. Somatic cell hybrids which are produced by fusing different types of somatic cells from two different tissues have been used as a valuable resource to discern the phenomenon of lineage- specific gene extinction. Identification of regulatory factors that mediate gene extinction in hybrids are key to understanding regulatory mechanisms that govern cell differentiation in a multicellular organism. Transcription …

Particle Mediated Enhanced Mass Transfer Of Diethylhexyl Phthalate: A Pilot Scale System Design, Melissa Buechlein

Masters Theses

"Phthalates are a class of SVOCs that are widely used as plasticizers and recently epidemiological and toxicological research has found a link between phthalate exposure and increased occurrences of adverse health effects. SVOCs can potentially partition into household dust and airborne particles. Models and micro chamber studies have identified that airborne particles effectively increase SVOC deposition to or emissions from surfaces; SVOCs partition to aerosols in the bulk air, the aerosols then migrate to the surfaces due to eddy and Brownian motion, and then the SVOCs is released inside the SVOC concentration boundary layer adjacent to the surface. Concentration boundary …

Measurements And Simulation Of Conductor-Related Loss Of Pcb Transmission Lines, Oleg Kashurkin

Masters Theses

"With continuously increasing data rates Signal Integrity (SI) problems become more and more challenging. One of the main issues in high-speed data transfer is the frequency-dependent loss of transmission lines. This thesis is dedicated to conductor-related loss mechanisms in printed circuit board (PCB) transmission lines.

This thesis provides the experimental investigation of conductor properties used for fabrication of PCBs. Particularly, the resistivity and conductivity along with the temperature coefficients of eleven copper types is measured and reported. A four probe measurement technique is used. Results were verified by two independent measurements and show discrepancy of less than 0.5%.

Another major …

A Cost Benefit Analysis Of Sst Based Volt-Var Control, Guruprasad Ramani

Masters Theses

"The overall objective of this thesis work is to improve system power quality with the help of solid state transformers (SSTs). Two methods to improve the system power quality are explored: a) achieving a unity power factor at all the load buses, and b) improving the system voltage profile to meet a desired voltage regulation requirement of 0.95

A Feasibility Study Of A Nuclear Power Plant With No Moving Parts, Jonathan Mark Schattke

Masters Theses

"In a nuclear reactor design, every moving part in a system is considered a failure point. In this study, a proposal is made for designing a nuclear reactor that has no moving parts by coupling an accelerator driven core (removing control system moving parts) to a magnetohydrodynamic generator (removing power generation moving parts) using mercury coolant (removing pumping system moving parts). Further safety is realized by using a subcritical core, where the core is never able to sustain a chain reaction on its own, obviating many safety systems. The design is verified with a Monte Carlo simulation "--Abstract, page iii.

Thermal Characterization Of Phase Change Materials For Thermal Energy Storage, Rami Mohammad Reda Saeed

Masters Theses

"The study provides a valuable and useful database for Phase Change Materials (PCMs) for Thermal Energy Storage (TES) applications. Only a few existing studies have provided an overall investigation of thermophysical properties of PCMs in this detailed manner. Several organic PCMs, namely Myristic acid, Capric Acid, Lauryl Alcohol, Palmitic acid and Lauric acid, have been characterized after being carefully selected to cover wide range of TES applications. Insights and information gained from this work will be applied toward the design and modelling of many low temperature thermal energy storage applications. The study experimentally investigated uncertainty of thermal characterization of PCMs …

Design And Fabrication Of A System For The Additive Manufacturing Of Transparent Glass, Luke John Gilbert

Masters Theses

"Despite glass' prevalence in the scientific and engineering community, very little research has been conducted attempting to additively manufacture (AM) glass. Even less research has been done on optically transparent glass. Glass’ material properties make it ineligible for most AM processes if the end result is to be transparent. Even small gas inclusions can cause large amounts of scattering. Additively manufacturing transparent glass brings the advantages found in other AM processes with the added benefit of having optical properties better than those found in polymers. Additively manufacturing glass also allows the optical properties of transparent parts to vary arbitrarily. This …

Multifunctional Wearable Epidermal Device For Physiological Signal Monitoring In Sleep Study, J V M S Avinash Kankipati

Masters Theses

"Sleep is the essential part of life. Thousands of people are suffering from different kinds sleep disorders. Clinical diagnosing and treating for such disorders are costly, painful and quite sluggish. To reach the demand many commercial products are into the market to encourage home based sleep studies using portable devices. These portable devices are limited in use, cannot be handled easily and quite costly. Advancements in technology miniaturized these portable devices to wearable devices to make them convenient and economical. Elastic, soft and thin silicon membrane with physical properties well matched with that of the epidermis provides conformal and robust …

Material Properties Characterization For Multilayer Pcb And Peec Macromodels For Above Plane Decoupling Capacitors, Xiang Fang

Masters Theses

"Accurate frequency-dependent dielectric properties are important for accurate modelling of signal and power integrity problems. And decoupling capacitors perform an important function in the impedance reduction of power distribution systems. Hence, precise dielectric properties and micromodels for decoupling capacitors are the key parts for the signal and power integrity design.

In Section 1, the existing method for extracting dielectric properties from fabricated multilayer printed circuit boards based on the measured electrical property of fabricated transmission lines is introduced and validated using simulations. And the potential errors in the procedure are discussed. After that Djordjevic-Sarkar causal dielectric model for dielectric properties …

Shale Instability Of Deviated Wellbores In Southern Iraqi Fields, Ahmed Ali Shanshool Alsubaih

Masters Theses

"Wellbore instability problems are the cause for the majority of nonproductive time in the southern Iraqi fields' developments. The most severe problem in terms of effort and disbursement which is referred to a pipe sticking in Tanuma shale formation. Examining the drilling data revealed that this phenomenon was mostly related to the shear failure of the wellbore. Thus, a geomechanical analysis and drilling parameters/ practice optimization analysis were performed on a field in southern Iraq based on data from 45 deviated wells. The geomechanics analysis predicted the suitable drilling fluid density to prevent onset shear failure by using the Mogi-Coulomb …

Mechanistic Understanding Of Water-Rock Interactions During High-Salinity Water-Flooding Of Carbonate Reservoirs, Pu Han

Masters Theses

"Chemically tuned water-flooding provides a relatively cheap method of enhanced oil recovery from carbonate and sandstone reservoirs. Several possible recovery mechanisms such as mineral dissolution, multi-component ion exchange, double-layer expansion, adsorption/desorption from rock surface, reduction in interfacial tension, and fines migration that have been proposed are widely debated. The combination of these processes may result in wettability alteration that increases sweep efficiency of water-flooding. Here, wettability alteration due to water-rock interactions will be examined numerically.

To evaluate the wettability alteration, separation between breakthrough curves of the non-reactive component and the cations based on the chromatographic separation will be used due …

Hybrid Manufacturing Processes For Fusion Welding And Friction Stir Welding Of Aerospace Grade Aluminum Alloys, Megan Alexandra Gegesky

Masters Theses

"Friction stir welding and processing can provide for joints in aerospace grade aluminum alloys that have preferable material properties as compared to fusion welding techniques. Aerospace grade aluminum alloys such as AA2024-T3 and AA7075-T6 are considered non-weldable by traditional fusion welding techniques. Improved mechanical properties over previously used techniques are usually preferable for aerospace applications. Therefore, by combining traditional fusion welding and friction stir processing techniques, it could be plausible to create more difficult geometries in manufactured parts instead of using traditional techniques. While this combination of fusion welding and friction stir processing is not a new technology, its introduction …

A Study On Non-Metallic Inclusions In Foundry Steel Process, Marc Leonard Harris

Masters Theses

"The effects of sample area and automated SEM/EDS feature analysis parameters (step size, magnification and threshold) on nonmetallic inclusion characterization results has been investigated and optimized. A post-processing program was developed to automatically determine average inclusion chemistry, total element concentrations within inclusions, and for generating joint ternary diagrams with size visualization for representing nonmetallic inclusion populations. Using these tools the evolution of nonmetallic inclusions was examined for 4320 steel at a participating industrial steel foundry. The steel was sampled throughout electric arc furnace melting through ladle refining to the final casting where an in-mold sampling procedure was developed to procure …

Radiation Noise Source Modeling And Near-Field Coupling Estimation In Rf Interference, Liang Li

Masters Theses

"With increasing complexities and shrinking size of modern electronic devices, the near-field RF interference issues are becoming challenging for RF-digital mixed circuit design. Predicting the coupling from digital module to RF antennas and mitigating RF interference is important to the system performance. The ultimate goal of this study is to address the desensitization issues existing in modern electronic devices that have mixed high speed digital-RF circuits, such as cellphone and wearable devices.

In order to estimate the near-field noise coupling from digital module to RF antennas, the noise source is anticipated to be replaced by its equivalent radiation model which …