Digital Commons Network^™

Inclusion Engineering In Femnal Steels, Rairu Vaz Penna

Masters Theses

"Low density high Mn and Al steels, or FeMnAl steels, show great promise for military vehicles and automotive applications in which high strength and toughness is a requirement. However, these steels are subject to processing challenges including development of oxide and nitride inclusions during melting and casting as well as a large as-cast grain size and heavy interdendritic segregation. This can lead to non-uniform heat treatment response and cracking during subsequent hot rolling. Adding up to 10%Al lowers the density of these steels by as much as 15%, unfortunately, this also results in large amounts of hard and faceted AlN …

Controlled Switching In Kalman Filtering And Iterative Learning Controls, He Li

Masters Theses

“Switching is not an uncommon phenomenon in practical systems and processes, for examples, power switches opening and closing, transmissions lifting from low gear to high gear, and air planes crossing different layers in air. Switching can be a disaster to a system since frequent switching between two asymptotically stable subsystems may result in unstable dynamics. On the contrary, switching can be a benefit to a system since controlled switching is sometimes imposed by the designers to achieve desired performance. This encourages the study of system dynamics and performance when undesired switching occurs or controlled switching is imposed. In this research, …

Amplitude-Preserved Processing Of The Blackfoot 10 Hz Seismic Data, Bader Mohammed A Algarni

Masters Theses

"The broadband 3C-2D seismic survey was acquired in the Blackfoot Field in southern Alberta. The single-component 10 Hz geophone data were reprocessed to increase vertical resolution and provide a better seismic image of the incised valley channel fill deposits in the Glauconitic Formation. The amplitude-preserved seismic processing of the data was followed by the Kirchhoff prestack time migration. The processing parameters and algorithms used were based on parameter optimization approach. Elevation statics and surface consistent residual statics were utilized to remove near surface delays in the data. Seismic noise, such as ground roll and air blast, were attenuated effectively by …

Archaeological Investigation Using Geophysical Methods To Locate Historic Byram's Ford Road, Marshall Seth Foster

Masters Theses

"Ground penetrating radar, a time domain electromagnetic metal detector and a frequency domain electromagnetic metal detector were used with the goal of locating a section of the Byram's Ford Road believed to be intersecting the historic Big Blue Battlefield in the Westport area of Kansas City, Missouri.

Ground penetrating data were acquired at three sites, Site A, Site B, and Site C. The time domain EM metal detector was used to acquire data at Site A, where subsequent ground truthing was conducted using the frequency domain EM metal detector and an excavation tool. Significant anomalies were visible on both the …

Unified Probe Launch Pattern Design And Methodology Of Differential Probe Characterization, Han Deng

Masters Theses

"Differential probe is wildly used in the signal integrity area to do the accuracy signal measurement in frequency domain or time domain. Comparing with traditional SMA connector measurement, the probe measurement has several advantages such as the high flexibility and measurement efficiency. Nevertheless, the probe has some disadvantages such as multiple design patterns and the difficulty of fast landing. In this thesis, a unified probe landing pattern is provided to solve the con of probes and a probe testing fixture is designed for characterize probe and extract the probe model.

In the first portion, a unified differential probe launching pattern …

Investigating The Use Of Class C Flyash-Based Geopolymer Cement As A Potential Alternative To Portland Cement To Seal Co₂ Storage Wells, Priyesh Parimal Jani

Masters Theses

"Capturing emitted carbon dioxide from the source of emission and storing it underground is one effective way to reduce the amount of CO₂ in the atmosphere and is called carbon capture and storage (CCS). For the successful CCS project, it is necessary to ensure long term storage of injected CO₂ inside these selected reservoirs. Portland cement used to cast wells in these reservoirs degrade in CO₂ environment and can create migration path for leakage of CO₂. The aim of this study was to provide a comprehensive review about the problem, to propose a new geopolymer …

Routing Algorithm For The Ground Team In Transmission Line Inspection Using Unmanned Aerial Vehicle, Yu Li

Masters Theses

"With the rapid development of robotics technology, robots are increasingly used to conduct various tasks by utility companies. An unmanned aerial vehicle (UAV) is an efficient robot that can be used to inspect high-voltage transmission lines. UAVs need to stay within a data transmission range from the ground station and periodically land to replace the battery in order to ensure that the power system can support its operation. A routing algorithm must be used in order to guide the motion and deployment of the ground station while using UAV in transmission line inspection. Most existing routing algorithms are dedicated to …

High-Speed Pcb Trace Design Using A Behavioral Surface Roughness Model And High-Speed Test Coupon Design With Non-Functional Pads, Han Gao

Masters Theses

"In high-speed digital systems as data rates increase to tens of gigabits per second, the loss from the conductor surface roughness cannot be ignored. Djordjeic and Huray roughness model is widely used to count for the conductor roughness loss. However the practical application of the existed models are not straight forward since the frequency-dependent dielectric loss is usually unknown, leading to high discrepancies at high frequencies (above 10 GHz). To solve this problem, a behavioral model was developed by adding a dispersive term to the dielectric. The dispersive term in the model captures dispersion behavior observed in the measurement accurately. …

Student Perceptions And Attitudes Towards A Technical Writing Service Course At Missouri S&T, Hannah Claire Coffman

Masters Theses

"In order to learn how STEM students perceive Missouri S&T's English 3560 Technical Writing class, I designed a research study to investigate how a sample population of 90 students viewed the class. Due to the nature of qualitative research, the results of this study cannot be generalized to a larger population. However, the results can and do provide insight into the situation of these Missouri S&T students in English 3560 classes and contribute to our collective understanding of the technical writing service course at Missouri S&T and other US universities. The study investigated whether the sample population of students who …

Radiation Immunity In Cable Harnesses And Differential P/N Skew In Pcb, David Nozadze

Masters Theses

"We develop an efficient method to model RF immunity of multiwire cable harnesses and study differential P/N skew effects on channels, channel performance and specifically on the eye diagrams at the SerDes receiver.

External radiation can induce unwanted signals in transmission lines. For example, external radiation from an antenna induces common-mode currents on the outer surface of cable shields. This common-mode signal makes its way through the shied due to its imperfections, inducing the inner common mode. When twisted pairs inside the cable are not balanced, inner common mode is in turn converted to the differential mode, which might compromise …

A Study On End-Anchorage And Bond Behavior Of Steel-Fiber Reinforced Cementitious Matrix Composites Externally Bonded To A Concrete Substrate, Christopher Michael Moore

Masters Theses

"Fiber reinforced cementitious matrix (FRCM) composites are a strengthening material consisting of continuous fibers embedded in an inorganic matrix that have the potential to provide additional flexural and shear strength to concrete and masonry members. When used for external strengthening, however, debonding of the material is often observed due to slippage of the fiber with respect to the matrix, causing loss of composite action and a reduction in load carrying capacity. The composite utilized in this study consisted of continuous steel fibers embedded in an inorganic cementitious matrix bonded to a concrete prism. Additionally, an end-anchorage system was implemented with …

Emi Design Of Flyover Qsfp (Fqsfp) Connector For 56+ Gbps Applications, System Level Modelling Of The Z-Directed Component (Zdc), Pranay Kumar Vuppunutala

Masters Theses

"This thesis comprises of two parts. Firstly, the Flyover Quad Small Form Pluggable (FQSFP) approach for 56+ Gbps applications is introduced to overcome the limitations from a large loss on typical QSFP ports with surface mount to Printed Circuit Board (PCB) traces. By replacing the PCB traces to the twinax cables, it is possible to achieve around 7 dB lower insertion loss at 40 GHz for the 12-inch path from the switch IC to connector than that of PCB trace with a low loss substrate. Also, to investigate electromagnetic interference (EMI) aspect of FQSFP approach, a simulation model of FQSFP …

Microwave Detection Of Surface Breaking Cracks In Metallic Structures Under Heavy Corrosion And Paint, John Robert Gallion

Masters Theses

"We live in the world of "aging infrastructures". In this environment, critical and heavily utilized infrastructure, i.e. ships, planes, bridges, etc., are operating at or beyond their designed age. Replacement is no longer an option and "retirement for cause" is the current approach to maintenance and replacement. Consequently, there is an ever-increasing demand for efficient and robust nondestructive evaluation (NDE) methods that can determine the physical health of these structures. Large structures, which are primarily made of metals, either steel or aluminum, are susceptible to high-stress cracking and corrosion. Stress-induced cracks in heavily corroded steel, used in bridges, railroads, storage …

Program Management For Concurrent University Satellite Programs, Including Propellant Feed System Design Elements, Shannah Withrow-Maser

Masters Theses

"Propulsion options for CubeSats are limited but are necessary for the CubeSat industry to continue future growth. Challenges to CubeSat propulsion include volume/mass constraints, availability of sufficiently small and certified hardware, secondary payload status, and power requirements. A multi-mode (chemical and electric) thruster was developed by at the Missouri University of Science and Technology to enable CubeSat propulsion missions. Two satellite buses, a 3U and 6U, are under development to demonstrate the multi-mode thruster's capabilities. Two key challenges related to these missions are the development of the feed system to support the thruster and management of the two bus programs' …

Impact Of Framing And Base Size Of Computer Security Risk Information On User Behavior, Xinhui Zhan

Masters Theses

"This research examines the impact of framing and base size of computer security risk information on users' risk perceptions and behavior (i.e., download intention and download decision). It also examines individual differences (i.e., demographic factors, computer security awareness, Internet structural assurance, self-efficacy, and general risk-taking tendencies) associated with users' computer security risk perceptions. This research draws on Prospect Theory, which is a theory in behavioral economics that addresses risky decision-making, to generate hypotheses related to users' decision-making in the computer security context. A 2 x 3 mixed factorial experimental design (N = 178) was conducted to assess the effect of …

Computational Fluid Dynamics Modeling Of Proppant Static Settling Velocity In High Viscosity Friction Reducers, Chen Yuan

Masters Theses

"In the current petroleum fracturing industry, it is necessary to understand the downhole migration and settling velocity of the proppant. If we can master this information well, it will be a great help to obtain effective propped fracture conductivity. In order to study the transport of proppants in the well, we used laboratory experiments and computer numerical simulations to compare the results to get a meaningful conclusion. We spent a lot of time building models on a powerful computer and comparing the experimental conclusions. We finally decided to use computational fluid dynamics (CFD) as the simulation platform, discrete phase method …

Gel Composition And Brine Concentration Effect On Hydrogel Dehydration Subjected To Uniaxial Compression, Xinrui Zhao

Masters Theses

"Gel treatment is a process that injects the gel into a reservoir to control the conformance and improve the sweep efficiency of injection fluids. At a certain pressure gradient, the gel dehydrates in a reservoir due to mechanical forces. This work evaluates the effects of the gel composition and brine concentration on gel dehydration under uniaxial compression. A sodium acrylate-co-acrylamide based gel cross-linked with N, N'-Methylenebisacrylamide (MBAA) was used for the study. The compression test is performed with a rheometer with a plate-plate geometry. The gel dehydration under pressure was measured to see how gel dehydration would be impacted by …

Diffusion Kinetics In Promising Adsorbents For Gas Capture Processes, Teresa Gelles

Masters Theses

"This reports the results of experimental studies aimed at characterizing the transport properties of promising adsorbents for various gas capture processes by the "zero length column" (ZLC) technique. ZLC was used to measure the intracrystalline diffusivities of single and binary components of ethane and ethylene in powder and pellet samples of paraffin-selective adsorbents Ni(bdc)(ted)_0.5 (Ni-BT) and ZIF-7 for the purpose of olefin/paraffin separation. Results show that binary gaseous systems result in intracrystalline diffusion time constants slightly lower than those in single component gaseous streams due to coadsorption effects. It was also found that ethylene diffusion was affected by surface …

Coupling Path Visualization Based On Reciprocity Theorem, Yang Zhong

Masters Theses

"A new method to visualize coupling path is proposed to help solve EMI problems. Based on the reciprocity theorem and the concept of reaction, coupling coefficient (CC) is defined to characterize coupling power density. For two-port networks, surface integral of CC can represent coupled voltage on the open-circuited port or coupled power on the loaded port. For dipole-moment based systems, surface integral of CC can represent coupled field components. The calculated CC should be a complex scalar at each point. By properly adjusting the excitation phases, the imaginary part of surface integral of CC will be zero and thus can …

Passively-Coded Embedded Microwave Sensors For Materials Characterization And Structural Health Monitoring (Shm), Katelyn Rose Brinker

Masters Theses

"Monitoring and maintaining civil, space, and aerospace infrastructure is an ongoing critical problem facing our nation. As new complex materials and structures, such as multilayer composites and inflatable habitats, become ubiquitous, performing inspection of their structural integrity becomes even more challenging. Thus, novel nondestructive testing (NDT) methods are needed. Chipless RFID is a relatively new technology that has the potential to address these needs. Chipless RFID tags have the advantage of being wireless and passive, meaning that they do not require a power source or an electronic chip. They can also be used in a variety of sensing applications including …

Development Of Test Methods For Characterizing Extrudability Of Cement-Based Materials For Use In 3d Printing, Jonathan Thomas Kuchem

Masters Theses

"3D printing is the process of creating three-dimensional objects using an automated additive manufacturing process. The 3D printing process has been used with materials such as metals and polymers, but application with cement based materials for the construction industry has yet to be developed. In this research, two main problems were investigated for printing cement based composite materials: extrudability and tensile reinforcement. Fiber-reinforced concrete (FRC) was studied as an internal reinforcing system to increase tensile/flexural strength. First, FRC was studied to investigate mechanical properties and use of fibers from waste tires as an environmentally friendly option. A reference mixture with …

Breaker Evaluation And Formation Damage Remediation Of Re-Crosslinkable Preformed Particle Gel (Rppg), Enze Zhou

Masters Theses

"Re-crosslinkable preformed particle gel (RPPG) is a newly developed preformed particle gel for improving sweep efficiency and oil recovery by blocking or reducing the conductivity of fractures and fracture-like channels or conduits. However, RPPG has the potential to plug the facilities or damage the formation if a treatment is not properly conducted.

This work presents the performance of selected oxidizing breakers on the degradation of RPPG. The influence of a few factors on the degradation process was investigated, including breaker type, breaker concentration, temperature, gel concentration, gel aging time, and gel size. Results indicate that breaker type, concentration, and temperature …

Less Is More: Beating The Market With Recurrent Reinforcement Learning, Louis Kurt Bernhard Steinmeister

Masters Theses

"Multiple recurrent reinforcement learners were implemented to make trading decisions based on real and freely available macro-economic data. The learning algorithm and different reinforcement functions (the Differential Sharpe Ratio, Differential Downside Deviation Ratio and Returns) were revised and the performances were compared while transaction costs were taken into account. (This is important for practical implementations even though many publications ignore this consideration.) It was assumed that the traders make long-short decisions in the S&P500 with complementary 3-month treasury bill investments. Leveraged positions in the S&P500 were disallowed. Notably, the Differential Sharpe Ratio and the Differential Downside Deviation Ratio are risk …

Analyzing The Effects Of Attitude Errors When Quantifying The On-Orbit Performance Of A Cubesat Micropropulsion System, Andrew Orion Watson

Masters Theses

"CubeSats and small satellites have become popular methods of performing space research. Accordingly, interest has also grown in designing micropropulsion systems to increase the lifespan of these satellites. This work describes the framework for analyzing the effects of imperfect attitude determination and control when quantifying the on-orbit performance of a micropropulsion system. The Gauss variation of parameters equations were implemented to model the orbital mechanics, with perturbing models for the zonal harmonics, atmospheric drag, and solar radiation pressure included. Two common sources for imperfections in a spacecraft's attitude were considered. The first was to consider the effect of the spacecraft …

The Effects Of Ambient Benevolent Sexism And Its Implications In The Workplace, Amanda E. Mosier

Masters Theses

"The purpose of this study was to examine women's reactions to witnessing benevolent sexism (i.e., ambient benevolent sexism). Female participants (n = 59) witnessed another woman being treated with hostile sexism (HS), benevolent sexism (BS), or no sexism and their reactions were examined in respect to a) working memory capacity, b) task-specific self-efficacy, c) mental intrusions of incompetence, and d) negative affect. The study also examined how participants' personal endorsement of BS impacted the relationship between sexism condition and the outcome variables. Results indicate that there were no direct effects of sexism condition on the outcome variables, though there was …

Small Satellite Earth-To-Moon Direct Transfer Trajectories Using The Cr3bp, Garrett Levi Mcmillan

Masters Theses

"The CubeSat/small satellite field is one of the fastest growing means of space exploration, with applications continuing to expand for component development, communication, and scientific research. This thesis study focuses on establishing suitable small satellite Earth-to-Moon direct-transfer trajectories, providing a baseline understanding of their propulsive demands, determining currently available off-the-shelf propulsive technology capable of meeting these demands, as well as demonstrating the effectiveness of the Circular Restricted Three Body Problem (CR3BP) for preliminary mission design. Using the CR3BP and derived requirements from NASA's Cube Quest Challenge, five different trajectory scenarios were analyzed for their propulsive requirements. Results indicate that the …

Characterization Of The Surface Condition In Aa6061 Resulting From Deep Rolling As A Function Of Common Industrial Parameters, Andrew Kenneth Layer

Masters Theses

"Roller burnishing is widely used in industry to improve the surface finish and fatigue life of components. As weight reduction continues to grow in the automotive and transportation industries, deep rolling can help maintain product performance by mitigating the increase in component stresses resulting from lower weight systems. Deep rolling parameters such as tool, applied angle, feed rate, spindle speeds, and relative tool direction all affect cycle time, product performance, and appearance. The effects of common industrial parameters on the resultant surface roughness and residual stress profiles were studied in this investigation. The samples were manufactured on a CNC lathe …

Near-Field Scanning Based Shielding Effectiveness Extraction For Board Level Shielding Cans, Harsh Shrivastav

Masters Theses

"The conventional definition of shielding effectiveness is well suited for calculating electromagnetic shielding in the far-field. However, in the near field, shielding effectiveness calculation is not so straight forward. In radio frequency interference problems, most of the field coupling occurs in near field. Having a well-defined method to calculate near-field shielding effectiveness is important for estimating the suppression of radio frequency interference using the shield cans. In this research, a method to extract the shielding effectiveness of board level shielding cans using near field scanning is developed. Shielding effectiveness is defined by modelling the shielded noise source as equivalent dipole …

Temporal Changes Of Nutrients Within The Lower Grand River Watershed And Selected Sites, Weston Scott Duley

Masters Theses

"This report presents the results of a study carried out in collaboration with the U.S. Geological Survey (USGS) and the Missouri Department of Natural Resources (MDNR) to estimate total nitrogen (TN) and total phosphorus (TP) at five USGS monitoring sites within Lower Grand River Watershed (LGRW) and two monitoring sites on the Missouri River. The objective of this study was to quantify temporal changes in TN and TP concentrations and compare those to best management practices (BMPs).

In this study, the approach to the analysis of long-term surface water-quality data by using Weighted Regressions on Time, Discharge and Seasons models …

Developing A Model System Of Liquid Lubricants For Space Applications: Multiple Alkylated Cyclopentane In Alumina Enclosed Surface, Vidit Singh

Masters Theses

"Lubricants are substances used for reducing friction wear tear and energy losses between two moving bodies. For space applications, normal lubricants cannot be used as they cannot survive the harsh and demanding conditions of space. Multiple Alkylated Cyclopentanes (MACs) have been utilized as space lubricants in recent times with tremendous results. NASA uses the MACs for their missions in space, in particular 1,3,4- tri-(2-octyldodecyl) cyclopentane sold by Nye Lubricants under the name of Pennzane^TM.

In this research, an effort has been made to identify appropriate potential models for simulating Pennzane molecules and to develop MD simulation codes to …