Digital Commons Network^™

A Model Study Of The Induction Log Applied To The Detection Of Asymmetrically Located Orebodies, Robert Walter Piekarz

Masters Theses

"This research project was undertaken to determine the possibility of using an induction log of the type applied in petroleum exploration, for the detection of conductive ore- bodies asymmetrically located with respect to a borehole. Since a mathematical analysis would be extremely complex, a model study was conducted, using graphite bodies of various shapes to simulate different modes of mineral occurence.

The investigation showed that these bodies were readily detectable, and were capable of yielding anomalous curves characteristic of their geometry. The values of apparent conductivity decreased rapidly with lateral displacement, from the logging tool, as expected, due to the …

A Correlation Of Heat Transfer Coefficients Using An Induction Heater, Charles Maurice Martin

Masters Theses

"This thesis represents a study of the following problems. (1) Determination of techniques and equipment which would give satisfactory correlation of experimental heat transfer coefficients with those obtained from acceptable heat transfer equations when using an induction heater as the heat source. (2) Determination of depth of energy deposition in a thick-walled tube due to induction heating.

Techniques were developed that gave a correlation between experimental and calculated coefficients that were within -5% for minimum flow and +8% for maximum flow.

Because of difficulties in positioning thermocouples, the depth of energy deposition could not be accurately determined. However, two surface …

Transpiration Cooling Of A Heat Generating Porous Plate, M. K. A. Hameed

Masters Theses

"This investigation is a continuation of a thesis by T. S. Purewal. Several of the simplifying assumptions made by the above author are either ignored or the justifiability of such assumptions is probed into in order to obtain a more rigorous solution. Effects of the assorted grain size, non-Newtonian cooling, direction of coolant flow, thickness of the porous heat generating plate, specific heat of the coolant, and compressibility of the coolant are investigated in this thesis. Variation of maximum temperature of both coolant and the solid material for different types of heat source distribution are also studied.

As the grain …

A Preliminary Study Of The Effect Of Heat Treatment On The Strength And Microstructure Of A Glass-Ceramic Material, P. D. Ownby

Masters Theses

"The strength and microstructure of a glass-ceramic material of the composition 53 percent SiO₂, 19 percent Al₂O₃, 15 percent MgO, and 13 percent Li₂O were studied. Cylindrical specimens of glass were formed and heat-treated to six different temperature levels for various time periods. The method of strength testing used was a diametral compression loading technique. It was found that the strength of this material increased initially with heat-treatment but then decreased. The strength characteristics of the completely crystallized glass ceramic material were found to be dependent on the initial nucleation period. Some factors which influenced anomalous crystal growth are described. …

A Critical Analysis Of The Development Of An American Business Apologetic From Knight And The Libertarians To Selekman And The New Business Moralists, Magondi N. Rudrabasavaraj

Masters Theses

Preface

America has attained a stature in economic life that is unique in modern times in the congregation of the nation of the world.

Undoubtedly American business enterprise, with its titans of industry, has been highly responsible in building up the stature of the United States of America.

But on the horizon of the American business world in recent years there has been gerenewed search for proper goals, values, objectives, and philosophies. The result of this renewed examination of values is the development of an American Business Apologetic. The critical issue before the American business world is "business-is-business--or is it?" …

An Analysis Of The Teacher Education Scholarship Students Of The Classes Of 1959 And 1961 At Eastern Illinois University, Dareld S. Swisher

Masters Theses

No abstract provided.

The Influence Of Economics Upon The Voice Of John Steinbeck: Some Evidence From Selected Readings, Bernard Earl Eagleton

Masters Theses

No abstract provided.

Ground Water Investigation In The Southern Half Of Franklin County, Missouri, Kemal Piskin

Masters Theses

"Increasing population and industrialization in Franklin County, Missouri, has led to increased demand for water. Much of this demand will be satisfied from ground water resources. Although the general geology of Franklin County has been mentioned in several publications, no detailed study of structure and ground water geology had been done. This thesis consists of study of stratigraphy, lithology, and geologic structure, and analysis of well log data to determine occurrence and availability of ground water, in the southern half of Franklin County.

Stratigraphy and lithology is compiled from previous literature, modified to agree with well log data. Structural geology …

Foraminifera Of The Cenozoic And Recent Genus Sphaerogypsina Galloway, Wayne C. Horton

Masters Theses

"The morphology of Sphaerogypsina as seen in thin section affords various characters useful in classification] 1) arrangement and composition of the wall (calcareous-perforate, radially crystalline); 2) layering of wall (like Gypsina, without layering or black line, having only microlamellae); 3) shape of test (always spherical); and 4) specific characters: size of test, order/unorder ratio, size of chambers, wall thickness, pore diameter, and type of embryonic apparatus.

Correlation of the above characters has allowed recognition of two new species. Comparisons with other genera strongly suggest placing the genus in the Family Gypsinidae (nom. correct.) rather than in the …

Detection Of Rust Formed Under Paint Films, James Larry Inglis

Masters Theses

"Corrosion is an evil that has plagued man since before the iron age. Three ways of controlling corrosion are: 1. alloy the metal to make it chemically inert to corrosion, .2. change the surroundings to a noncorrosive atmosphere, and 3. isolate the metal from the corrosive atmosphere, as for instance by the application of a number of coats of paint that has been found to be the most economical method.

At present, there is no reliable method of testing the effectiveness of a paint film that does not require the corrosion products to destroy the paint film and show themselves …

A Study Of Duffing's Equation, Charles Kirby Murch

Masters Theses

"The unforced cases of Duffing's equation and the equation of the simple pendulum are considered by imposing certain conditions on a linear partial differential equation. Geometrical arguments are presented which lead to solutions of the special cases considered.

Undetermined functions of integration in the solutions limit their use to the approximation of systems with small non-linearity"--Abstract, page ii.

Development Of A Simple Bar Method Thermal Conductivity Test, V. J. Flanigan

Masters Theses

"A linear flow bar method type apparatus was set up for finding thermal conductivities by comparison techniques. Comparison technique consist of using a standard specimen where the thermal conductivity is known and comparing it to the unknown specimens to find their conductivity. Apparatus of this type usually uses thermocouples for the required temperature measurements, but thermistors were used in this experiment. The thermistors used required calibration to measure accurate temperatures and this was accomplished by using the known temperatures of the changes of state of some common materials. Five alloys were used to evaluate the method: SAE 1020 steel, gray …

The Effect Of The Rolling Load On The Micro-Structure Of Low Carbon Sheet Steel, Jerry Lee Cadden

Masters Theses

"A Stanat 315, two high-four high, combination rolling mill is used to cold roll annealed, low carbon steel strips. A method of measuring the rolling load was presented. The method consisted of constructing a load cell using SR-4 strain gages attached to a steel column. The load cell was placed under the hold down screw of the rolling mill and a known load was applied. The stresses from this load were transferred to the mill housing where another SR-4 strain gage was located. The strain in the mill housing was recorded at the corresponding applied load. During rolling, the strain …

Transpiration Cooling Of A Porous Plate, Stephan A. Sayegh

Masters Theses

"Transpiration cooling has long been known as an effective way of removing heat from porous materials. This thesis is a new approach to one of the problems of transpiration cooling in the steady state.

The specific problem considered here is that of a uniform porous plate through which a liquid is forced. This liquid vaporizes at a short distance from the surface through which it is forced and leaves the porous plate at the other surface which is exposed to hot gases. It also protects the hot surface by forming an insulating layer between that surface and the hot gases. …

Analysis Of Flat Plates By Reaction Distribution Method, David D. W. Yang

Masters Theses

"This study was made to analyze rectangular flat plates by the method of Reaction Distribution and to compare results obtained by this method with that of other methods. The basic approach is to divide the plate into an equivalent grid system and introduce temporary supports at the intersecting joints. The results from this study shows that the Reaction Distribution method is useful in a qualitative analysis of the behavior in a plate but is less satisfactory in obtaining reliable quantitative results"--Abstract, page 2.

A Study Of The Permeability And Separation Of Carbon Dioxide And Hydrogen By Gaseous Diffusion Employing Barriers Of Polystyrene, Carl J. Wallace

Masters Theses

"The purpose of this investigation was to study the permeability and separation of carbon dioxide and hydrogen by gaseous diffusion employing barriers of polystyrene. The offset of temperature and barrier thickness on the permeability and separation of carbon dioxide and hydrogen wore Investigated for barriers of one, three, and five-mil thicknesses and for temperatures of 26, 35, 45, and 50 degrees centigrade.

With an increase in barrier thickness of one to five- mils, the permeability of carbon dioxide decreased to one-fourth of its value at the one-mil thickness. The hydrogen permeability decreased to approximately two- thirds of its value at …

A Study Of Composite Beams Made To Find An Approximate Relationship Between The Top And Bottom Flange Steel Ratio, Murli U. Hasrajani

Masters Theses

"At present in building construction the use of the composite beams is not very common. The use of the concrete beams is seen in almost all construction. By using composite beams in building construction more durability and savings in cost could be achieved. This paper shows an approximate design procedure which could be followed without running a number of trials with different sections to arrive at the required one. The ratio of top flange steel to the bottom flange steel can be determined if one knows the loads, span and the depth of the beam required"--Abstract, page i.

Experimental Stress Analysis Of Bolts In A Flange Coupling, Vijay Rastogi

Masters Theses

"In this investigation an attempt has been made to determine simple formulae leading to a better, more useful and much safer design of flange coupling bolts. The bolts were tested under tensile loading and bending and hence the results obtained apply for bolts under these modes of loading only.

The behavior of flange bolts under different initial tightening torques was studied by measuring strains in a bolt on which strain gages had been attached* . From this, the load producing separation of flanges, under different tightening torques, was determined and used in deriving formulae for prediction of the load for …

Neutron Flux Mapping Of The Msm Reactor, Cary Chow-Yuen Chen

Masters Theses

"This investigation presents a mean to determine thermal neutron flux of a reactor by irradiating copper wires inside the fuel elements. The activity recorded after decay correction, is the relative thermal neutron density. Thermal neutron flux is a measure of the neutron density at thermal energy, 0.025 ev.

Gold foils irradiated at National Bureau of Standards were used as the absolute neutron flux calibration standards. The average flux of the reactor with water as the reflector ranges from 7.24 x 10¹⁰ neutrons/cm² - sec. to 7.87 x 10¹⁰ neutrons/cm² - sec. as obtained from the calculations. …

A Study Of Placer Tin Materials From Southern Thailand, Somkiat Ganthavee

Masters Theses

"This thesis deals with a series of investigations of placer tin samples from a Chinteik's Tin-dredge, Gnaw District, Ranong Province, and the Tin-Pet mine, Phang-gna Province, in southern Thailand.

A brief summary of the geography and geology of Thailand as a whole has been given as a general introduction to the source of the materials studied in this thesis.

The results of sieve analyses have shown that the sluice boxes do not effectively concentrate the cassiterite grain below 0.147 mm. from the rough concentrate treated in the tin-dressing shed.

It has been found that roundness and shape determinations of quartz …

A Determination Of Vapor Pressure Of Barium In The Thermal Production Of Barium Metal, Thomas A. Theobald

Masters Theses

The Knudsen effusion method was used to find the equilibrium reaction pressure of barium for the following reactions:
4BaO + 2Al - 3Ba + BaO·Al₂O₃ (l)
4BaO + Si - 2Ba + 2BaO·SiO₂ (2).
The resulting barium pressure for reaction (l) ranged from 0.27 mm. Hg to 1.77 mm. Hg in a temperature range of 940°C to 1086°C. The barium pressures for reaction (2) varied from 0.38 mm. Hg to 1.94 mm. Hg in a temperature range of 1000°C to 1086°C. The free energies of formation of BaO·Al₂O₃ and 2BaO·SiO₂ at 1087°C …

Circular Arch Analysis, Aylmer Pao-Sheng Cheng

Masters Theses

"This work presents an analysis of a two-hinged circular arch by both the elastic theory and the deflection theory. The basic assumption made in this analysis was that the moment of inertia of the arch rib and the normal force vary as the secant of the angle with respect to the crown. The increase of maximum moment as found by the deflection theory was in the range of 30%"--Abstract, page 2.

Thermal Conductometer For Liquids, Yuan-Kai Chang

Masters Theses

"The published data pertaining to the thermal conductivity of liquids are of such a character that it is very difficult to determine from them the correct value, or the temperature coefficient for any liquid.

Most of the published values of thermal conductivity for liquids are evaluated at one particular temperature. It is the purpose of this investigation to design, construct and calibrate a thermal conductometer for liquids over a temperature range of 30°F to 200°F.

Since water and glycerol were the only liquids found by this investigator with published data on their conductivities as a function of temperature, they were …

Syntheses And X-Ray Investigations Within The System Fes₂-Cos₂, Samuel Shu Mou Chan

Masters Theses

"Pyrite (FeS₂), cattierite (CoS₂), and various transitional members of the solid solution compounds were prepared. The methods used are as follows:

First, sulfides of cobalt, iron, or cobalt-iron were obtained by precipitation from a mixture of the cobalt chloride and/or ferrous sulfate in an aqueous solution. The dried precipitates were then mixed with an equal weight amount of sulfur and placed into silica glass tubes. After evacuation, they were filled with hydrogen gas of 3/4 of atmospheric pressure and sealed. The samples were then heated up to 500°C (for FeS₂), 650°C (for FeS_{2 …}

Analog Study Of Vibratory Forces In Sorting Machine, Navnit Chhaganlal Mehta

Masters Theses

"This investigation involves the study of the reduction of vibratory forces in a sorting machine. The equivalent masselastic system is shown in Figure 1, in solid lines. In this figure the mass m₁ represents the main structure for the mounting of the machine, the mass m₂ is the main bearing blocks and the mass m₃ is the vibrating basket. The elastic stiffness indicated as k₁ represents the mounting spring for the entire unit, the stiffness k₂ is that of the beam structure by which the bearing block is attached to the main structure, and the stiffness k₃ is that of …

The Effect Of A Continuous Low Temperature On The Operation Of Waste Stabilization Lagoons, Ralston Kennedy Dennis

Masters Theses

"This study was undertaken to determine the effect of a continuous low temperature on the operation of a waste stabilization lagoon and to provide information of value to the sewage treatment field.

The investigation was conducted using two experimental lagoons subjected to a continuous illumination of 550 to 600 foot candles emitted by two fluorescent light fixtures. Of these units, the Cold Room Lagoon was maintained at a controlled temperature of 5° C. and the Warm Room Lagoon was operated at room temperature in the range of 16 to 32° C.

Dissolved oxygen and biochemical oxygen demand determinations were the …

The Application Of Preaeration Of Sewage To The Design And Operation Of Waste Stabilization Lagoons, Richard G. Huber

Masters Theses

"The application of preaeration of sewage on the operation and design of waste stabilization lagoons was investigated and its effect on the permissible BOD loadings was determined to provide original and basic information of value to the sewage treatment field.

The investigation was conducted using two 15 gallon aquariums, one of which was designated as the Control Lagoon and the other as the Test Lagoon. These experimental lagoons were subjected to 12 hour diurnal light and dark cycles, provided by means of fluorescent light fixtures.

Raw sewage and aerated raw sewage were fed daily to the Control and Test Lagoons, …

Application Of Digital Computer To Magnetic Data Interpretation Using Surface Integral Method, Afif Hani Saad

Masters Theses

"A simple method is developed for the calculation of the magnetic effect due to three-dimensional bodies. The method is based on the use of surface integration instead of volume integration. Thus, any three-dimensional body can be considered as having two surfaces, upper and lower, with magnetic pole distributions. Simple equations based on potential theory have been derived for the calculation of the vertical component and total intensity due to these surface distributions of poles. The anomalous field of the body can be obtained by subtracting the effect due to one of the surfaces from that of the other.

The method …

A Study Of The Chemical Kinetics, Activation Energy And Difference Effect On Beryllium Dissolving In Mineral Acids, Daniel Santhamurthi Gnanamuthu

Masters Theses

"The rate of dissolution of polycrystalline beryllium was studied in hydrofluoric, hydrochloric and sulfuric acids. Two samples of beryllium containing different amounts of beryllium oxide were used. The experiments were performed at temperatures ranging from 20 to 50°C, and at various acid concentrations. The kinetics of these heterogeneous processes conformed to a reaction order of approximately one in all the cases. Since the conditions of the surface were complex during dissolution, these might complicate the reaction. This might be due to the oxide layer, which is present as impurity.

The difference effect was determined at various acid concentrations at 25°C …

Study Of The Copper-Uranium Deposits At Vilcabamba, Department Of Cuzco, Peru, Oscar Aguilar

Masters Theses

"Uranium has been known in the Vilcabamba district of Cuzco, Peru since 1954. Copper ores of high silver content were worked by the Spaniards during the seventeenth and the early eighteenth centuries, At the beginning of the twentieth century these ores were worked intermittently; during the last fifty years no mining operation has been going on.

The oldest rocks in the thesis area consist of Ordovician phyllites. The presence of Devonian in the area is questionable, but has been recognized 5 km. away from the thesis area. A conglomerate of limited lateral extent of Mississippian age overlies the Devonian (?) …