Digital Commons Network^™

The Construction Of A Single Crystal Neutron Diffraction Unit And Measurement Of Effective Neutron Temperature, Larry Dean Thompson

Masters Theses

"The continued expansion of the nuclear reactor facility and the nuclear engineering program makes it desirable that a neutron spectrometer be available at the reactor facility. This unit would be available for use in graduate and undergraduate laboratories and for graduate research.

A single crystal, white radiation spectrometer including collimator, automatic controls, and shielding was designed and constructed.

The performance of the unit was checked using LiF and Cu crystals. A rocking crystal curve and a θ - 2θ curve was obtained with each crystal. The effective neutron temperature was then determined from the LiF crystal θ - 2θ curve"--Abstract, …

Comparison Of Measured And Calculated Stiffnesses For Lightweight Normal Concrete Beams, Raman Patel

Masters Theses

"This study is a presentation of the findings involving experimental measurements of stiffness (EI) for different percentages of reinforcement steel in normal and lightweight concrete beams. The experimental values of stiffness are compared with calculated values obtained by applying the standard reinforced concrete theory. The measured values of stiffness obtained by the rotation method are compared with those obtained by the deflection method. Of the thirty beams that were tested, fifteen were tested for normal concrete and the remaining fifteen for lightweight concrete. Each of these beams were tested at different ages, ranging from seven to twenty-eight days.

The test …

The Elastic And Anelastic Constants Of A Synthetic Fluor-Mica Formed By Glass-Ceramic Fabrication Techniques, John H. Ainsworth

Masters Theses

"A tetrasilicic fluor mica, K₂Mg₅Si₈O₂₀F₄, was synthesized using glass forming techniques. Density changes, weight losses, and shrinkage, as well as elastic and anelastic properties, were measured on bars heat-treated at selected temperatures between 500°C and 1150°C to determine the characteristics of this material. Phase changes were followed by determining thermal expansion, logarithmic decrement, and modulus of elasticity from room temperature to 800°C.

It was found that the elastic and anelastic constants decreased gradually with heat treatments from 600°C to 1000°C. This indicated progressively increased structural ordering. Heat treatments above 1000°C …

The Transmission Of Loads To Point Bearing Piles In Sand Beneath Retaining Walls, Alan Albert Kamp

Masters Theses

"An experimental investigation was made of the way in which loads were transmitted to point bearing H-piles in sand under a retaining wall. Using a plastic model, the moments and axial loads were determined along the length of the pile by measuring the strains with electric strain gages. A comparison was made of the experimental results at the top of the pile and the analytical results at this point; the latter obtained from the common practice used in design. The comparison was very poor because the excessive horizontal load (that part of the horizontal load which could not be carried …

Buckling Strength Of Titanium Alloy Columns In The Elastic And Inelastic Range, Richard O. Rintoul

Masters Theses

"The purpose of this study is to find experimentally the buckling strength of titanium alloy (Ti.-6Al.-4V.) columns and to determine a suitable equation to be used in the design of titanium columns in the elastic and inelastic range.

Effective length over radius of gyration ratios of from 178 to 16.1 were studied. High strength steel plates with cylindrical radii milled in the faces served as column ends while cylindrical radii ends were milled on the columns. SR-4 strain gages were used at the mid-points of all columns to determine lateral deflection and predict a theoretical buckling stress. Actual column loads …

Geology Of Pride Mine And New Standard Mine Area, Northwestern Yuma County, Arizona, Henry E. Fernandez

Masters Theses

"A thick section of presumably Precambrian gneiss with thin intercalated bands of marble and schist has been mapped. There is structural continuity within these rock types as they are mutually intercalated, conformable, have gradational relations and show equal participation in the same individual fold. The layers of schist and marble in the gneiss can be followed over long distances. These rocks have undergone intense regional metamorphism, primarily dynamic, with a possible regional compressive force generated from NW-SE giving rise to sets of folds and faults in the area. From structural, petrographic and field evidence, it is concluded that the metamorphic …

A Study Of The Effect Of Surface Beveling On Silicon Rectifiers, Gary L. Voorhis

Masters Theses

"The problem in this thesis is to experimentally obtain voltage vs distance data for different angles of bevel, to determine the optimum bevel angle on the basis of minimum surface electric field, and also to determine the location of the maximum surface electric field with respect to the p-n junction. Experimental equipment is constructed and results are graphically illustrated. It is concluded that in general the maximum surface electric field decreased as the bevel angle decreased, that neglecting practical considerations the optimum bevel angle was 3⁰, and that the maximum surface electric field occurred near, but not at the p-n …

The Effect Of Epoxy Resins On The Plasticity Index Of An A-6 Soil, A. R. Van Steenbergen

Masters Theses

"This thesis reports the results of an investigation of the variation in plasticity of a clayey soil after treatment with small quantities of epoxy resin and curing agent or with curing agent alone. The series of samples tested consisted of an A-6 soil obtained from the vicinity of Rolla, Missouri, combined with: 1. 0-3% of triethylenetetramine hereafter referred to as TETA. 2. 0-3% of diethylenetriamine hereafter referred to as DETA. 3. 0-3% of Araldite 6010 resin cured with TETA. The TETA content was varied form 20% to 100% of the resin by weight. 4. 0-3% Araldite 6010 resin cured with …

Analysis Of Continuous Folded Plate Roofs, Yung-Ping Wang

Masters Theses

"This work presents an analysis of continuous folded plate roofs considering the effects of relative joint displacements. For this analysis the normal modes of the lateral beam vibration were used as the form of the deflection curve and the loading was sinusoidal. By using symmetry and anti-symmetry, a possible method of analyzing prismatic folded plate roofs comprising one bay transversely but continuous over two or more spans longitudinally is suggested"--Abstract, page ii.

Analysis Of The Flow Characteristics Through A Water Pressure Regulator, Anthony Lee Jatcko

Masters Theses

"This thesis presents an analysis of the flow characteristics through a water pressure regulator. Characteristic curves of the relationship between pressure drop through the regulator and flow through the regulator are developed. To further analyze these relationships, a least squares computer analysis was used to develop equations to fit these curves. An investigation into the modes of dissipating pressure energy in this type of regulator tends to indicate that a significant portion of the energy is lost through viscous shearing action in the area of high turbulence. The aforementioned characteristic curves also showed definite critical pressure points in the form …

Thermal Degradation Of Poly (Methyl Methacrylate) In Solutions In A Closed System, Vikram Pranjivandas Parikh

Masters Theses

"A study has been made of the thermal degradation of poly (methyl methacrylate) of two different molecular weights, 2,303,000 and 43,000, in 1,2-dichloroethane in a closed system. The results indicated that the polymer having a molecular weight of 2,303,000 undergoes degradation while the low molecular weight polymer 43,000 undergoes reverse polymerization, and the molecular weight remains constant. The molecular weight of high molecular weight samples after 48 hours decreased from 2,303,000 to 2,232,000 and 1,690,400 at 50⁰C and at 98.5⁰C, respectively"--Abstract, page [i].

Model Study Of A Folded Plate Roof, Graham G. Sutherland

Masters Theses

"The purpose of this study was to conduct a model study of a folded plate roof in order to determine the feasability [sic] of using model studies as a method of design. Dimensional analysis was used to derive prediction equations for determining the stresses in two prototype structures, when the stresses in the model were known. One model and two prototype folded plate roofs were constructed of plexiglas [sic]. SR-4 strain gages were attached to the structures and strain readings taken as a uniform vertical load was applied in increments. From the strains the stresses at various points in the …

Optimum Finite Memory Nonlinear Filter, Ching-Chyoun Yang

Masters Theses

"This thesis investigates the possibility of using the Zadah theory and a machine type computer to design an optimum finite memory nonlinear filter for extraction of Poisson distributed signal pulses from a background of Gaussian noise. Basically the procedure involves the technique of solving simultaneous equations by the computer. We demonstrate that it is possible to find the limitation of the filter of class N₁ in terms of an absolute minimum mean square error. However, due to the capacity of the computer we do not actually determine the absolute minimum. Nevertheless we do show that the mean square error decreases …

An Instrument For The Measurement Of Anelastic Properties Of Glass, Thomas Frederick Miller

Masters Theses

"An inverted torsion pendulum for measuring the internal friction and dynamic shear modulus of glass fibers over an extended temperature range has been constructed and calibrated. The calibration consists of the determination of the moment of inertia. Extraneous damping losses were investigated and primary sources were found to be (1) the suspension thread, (2) the method of securing the fiber and (3) air damping. Anelastic measurements were made on an annealed vitreous silica fiber and a soda-lime-silica fiber"--Abstract, page ii.

Discharge Characteristics Of Side Weirs, Edgar Snowden

Masters Theses

"The purpose of this study is to investigate the division of flow of water in a flume of rectangular cross-section when the flume is provided with a side weir. An equation has been derived so that the quantity of water flowing over the side weir compared to the quantity of water flowing in the main channel can be predicted. This ratio is acceptable only within the ranges of heads, velocities, and weir lengths imposed by the geometry of the system tested"--Abstract, page ii.

The Effect Of Lubri-Coolant Application At The Tool-Chip Interface On Tool Forces, Bomi Ardeshir Hathikhanavala

Masters Theses

"The purpose of this experiment was to determine the effectiveness of a lubri-coolant directed in such a way that it impinged just below the chip at the tool-chip interface in an orthogonal cutting process. This was compared to the conventional method of flooding lubri-coolant around the tool-chip area ... The results obtained show that the forces required to cut a material were less if the lubri-coolant was directed on the tool-chip interface when larger values of feed and depth of cut were used, and that with smaller values of feed and depth of cut, the method of flooding was equal …

The Geology Of The Interstate Highway 244 And 44 Exchange, Kirkwood, Missouri, John Neil Thomas

Masters Theses

"During the summer of 1964, construction was completed on the intersection of Interstate Highways 244, 44 and U.S. Highway 66, one mile southwest of Kirkwood, Missouri. during the construction of the interchange, numerous artificial exposures of rocks of the middle Mississippian Meramecian Series were exposed. This provided an excellent opportunity for examining fresh exposures near the type Meramecian Series. The formations of the area were studied, and startigraphic [sic] sections were prepared from three of the more complete sections that were measured and described. The highway cuts expose complete sections of the Warsaw and Salem formations, and the lower part …

Analog Computer Study Of Unequally Spaced Antenna Arrays, Fred M. Dickey

Masters Theses

"The problem undertaken in this thesis was to study the basic properties of unequally spaced antenna arrays. The study was done on a trial and error basis by simulating the expression for the far field pattern of a general array on an analog computer. Many patterns were obtained from the analog computer for the purpose of comparison. The patterns of two spacing schemes that are typical of unequally spaced arrays are presented for the purpose of illustration"--Abstract, page ii.

A Survey Of The Audio-Visual Services For Instruction On The Campus Of Eastern Illinois University, Earl W. Jeffers

Masters Theses

No abstract provided by author.

A Study Of Selected Choral Works Of Randall Thompson, A. Dennis Sparger

Masters Theses

No abstract provided.

A Terrain Study Of The Bloodland Quadrangle, Pulaski County, Missouri, Lawrence E. Mullins

Masters Theses

"This study is an investigation of the environmental conditions which affect cross country movement for tracked military vehicles on a major portion of the Fort Leonard Wood Military Reservation.

The terrain has been mapped from the trafficability standpoint by an investigation of the geology, topography, pedology and restrictive vegetation characteristics of the Bloodland seven and one-half minute quadrangle. The terrain analysis was accomplished by a combination of map study, laboratory investigation, photo interpretation, and direct field study of representative soil and vegetation types. The conclusions of this analysis are presented in the form of a cross country movement map"--Abstract, page …

A Study Of Hot Shortness In Steels, Koang-Hwa Kung

Masters Theses

"In this investigation an attempt was made to study the deformation of a number of laboratory-melted and commercial steels. A compressive load was applied to the steels at constant temperature and also during heating. The amounts and rates of deformation in these two types of tests was not consistent: in the constant temperature tests the hot short steels deformed more than the others while they appeared to deform less during heating. Metallographic examination of the sulfides indicated that the sulfides in cast steel are not stable and that they change during heating and hot working"--Introduction, page 2.

The Effect Of Copper Upon The Eutectoid Reaction In The Zinc-Aluminum System, Paul Theodore Corcoran

Masters Theses

"A Leitz dilatometer was used to study the kinetics of the eutectoid reaction in the zinc-aluminum system and the effect of small additions of copper upon this reaction. Three alloys were investigated: a pure 78% zinc - 22% aluminum alloy; a 78% zinc - 21.9% aluminum - 0.1% copper alloy; a 78% zinc - 21% aluminum -1.0% copper alloy. It was found that this reaction was similar to the pearlite reaction in the iron-carbon system. The reaction occurred by diffusion processes and the products of the reaction looked similar to pearlite when examined under the microscope. Copper was found to …

The Kinetics And Mechanisms Of The Reaction Of Benzyl Chloride With Potassium T̲-Butoxide In T̲-Butyl Alcohol, Der-Rong Chen

Masters Theses

"Benzyl chloride is a moderately reactive halide. Substitution of the Cl⁻ by other nucleophiles, e.g., HO⁻, AcO⁻, S₂O₃⁻, Br⁻ etc. proceeds almost quantitatively in solutions at convenient temperatures ... The object of this study was to investigate if the less basic t̲-butoxide in t̲-butyl alcohol would afford the same product, viz., stilbene; and, if so, by what mechanism. A study of the products and kinetics of the interaction between benzyl chloride and potassium t̲-butoxide in t̲-butyl alcohol therefore has been initiated"--Introduction, page 1.

Oxidation Of Ortho-Xylene To Phthalic Anhydride Using A Fluidized Bed Catalysis, Jyue-Sheng Wang

Masters Theses

"This investigation was conducted to study the vapor-phase oxidation of o-xylene to phthalic anhydride in a fluidized bed reactor. Parameters investigated during the study were temperature, molar ratio of air to o-xylene vapor, and space velocity. The catalyst used was vanadium pentoxide supported on a silica base and diluted with potassium sulfate. The studies were conducted on a laboratory scale"--Abstract, page ii.

A Measurement Of Dead Space And Its Effect On The Homogeneous Nucleation Rate Of Water Vapor In Helium, Michael A. Grayson

Masters Theses

"The existence of a "dead space" surrounding each nucleated water droplet is demonstrated and measurements of its rate of development are made. The effects of this "dead space" are considered to be due to both the removal of vapor from the helium-water vapor mixture and the evolution of heat about the drop due to its growth. The results confirm the usefulness of the concept of a "dead space" and provide a means for its measurement with respect to time. Recommendations for further study and a method of correcting for dead space effects is given"--page [i].

The Production Of Glutamic Acid By Fermentation, Tsun-Hsiung Li

Masters Theses

"The method of producing glutamic acid by fermentation was studied in shake flasks and in a five liter fermentor. Strains of the micro-organism, Micrococcus glutamicus, were used to produce glutamic acid under different conditions ... A literature review of the general properties of glutamic acid and industrial methods of glutamic acid production was made. A detailed discussion of the fermentation method of glutamic acid production was also included"--Abstract, page ii.

Thermal Degradation Of Poly (Methyl Methacrylate) In Solution In Various Solvents, Ya-Chih Chen

Masters Theses

"A study has been made of the thermal degradation of poly (methyl methacrylate) of different molecular weights in toluene, ethyl acetate and chloroform. Four poly (methyl methacrylate) samples having molecular weights of 2,210,000, 733,000, 320,000, and 43,00, respectively were studied in this investigation. The results indicated that the polymer having a molecular weight of 2,210,000 undergoes degradation while the low molecular weight polymers having molecular weights of 733,000, 320,000, 43,000 undergo reverse polymerization"--Abstract, page [ii].

Transformations Of Tryptamine And Tryptophan By Basidiomycetes, Hsaio-Lung Cheng

Masters Theses

"The product formed from tryptamine by Trichloloma nudum was identified as indoleacetic acid (IAA) and from tryptophan by Cantharellus cibrarius as indolelactic acid (ILA). The products were extracted from the spent media with organic solvents. Purification and identification of the crystalline transformation products were accomplished by means of paper chromatography, spectrophotometry and thin layer chromatography.

The conversion of tryptamine and tryptophan was also studied in cultures of Lencopaxillus paradoxus, Pluteus granularis and Pleuatus ostreatus. Only Pluteus granularis was found to transform tryptamine into IAA. Lencopaxillus paradoxus transformed tryptamine into oxindoleacetic acid (OIAA).

Paper chromatography proved to be useful …

Matching Of A Horn Antenna To Its Dense Surrounding Media By The Use Of Artificial Dielectric Methods, Paul Arthur Ray

Masters Theses

"The purpose of this thesis is to design an artificial dielectric slug to match a horn in a media such as water and to discuss a method of determining experimentally its dielectric properties. The design is based on known artificial dielectric methods. The method of determining the dielectric properties is by microwave waveguide reflection techniques. This thesis deals with the theoretical aspects and suggests an experimental method of determining the practicability of such a matching method"--Abstract, page ii.