Open Access. Powered by Scholars. Published by Universities.®

Digital Commons Network™

Open Access. Powered by Scholars. Published by Universities.®

Masters Theses

Discipline
Institution
Keyword
Publication Year
Publication Type

Articles 6151 - 6180 of 7904

Full-Text Articles in Entire DC Network

Effect Of Hydrostatic Pressure On Anelastic Stress Relaxation In A Mixed-Alkali Silicate Glass, Young-Gil (Gilbert Y.) Kim Jan 1969

Effect Of Hydrostatic Pressure On Anelastic Stress Relaxation In A Mixed-Alkali Silicate Glass, Young-Gil (Gilbert Y.) Kim

Masters Theses

"The effect of hydrostatic pressure on the anelastic stress relaxation of a mixed-alkali silicate glass (0.05 Na₂O, 0.95 K₂O, 3 SiO₂) was studied at 75°C between ambient pressure and 6 kbar. The activation volume of diffusion was found to be - 4.2 cm³/mole. It is proposed that a reequilibration of the defect population at pressure gives rise to the negative activation volume of diffusion"--Abstract, page ii.

Go to article

A Comparison Of Lumped Parameter Models Commonly Used To Describe One-Dimensional Vibration Problems, Suresh Kumar Tolani Jan 1969

A Comparison Of Lumped Parameter Models Commonly Used To Describe One-Dimensional Vibration Problems, Suresh Kumar Tolani

Masters Theses

"Three lumped parameter model representations of the one-dimensional uniform continuous system in a vibration state are examined. The exact (continuous) solutions were used as a reference to evaluate the accuracy of the results obtained via these discrete element models. The model comparisons, carried out for both the principal modes and the systems under forced excitations, are based on the maximum strain energy. The effect of varying the number of segments in the model representation showed improvement in approximating the exact strain energy solution as the number of segments was increased. In general, the results of the model comparisons based on …

Go to article

Stratigraphy And Economic Geology Of Uranium-Bearing Sediments In The Poison Spider District, Natrona County, Wyoming, Carlos Enrique Reijenstein D'Acierno Jan 1969

Stratigraphy And Economic Geology Of Uranium-Bearing Sediments In The Poison Spider District, Natrona County, Wyoming, Carlos Enrique Reijenstein D'Acierno

Masters Theses

"Geologic, stratigraphic, and mineralogic characteristics of the Eocene Wind River and Oligocene White River Formations were determined for the southern portion of the Poison Spider District, Natrona County, Wyoming. Sieve analysis and heavy mineral techniques were used to recognize stratigraphic units, determine their environment of deposition, obtain a better knowledge of the grain size distribution, and to identify a possible source area for the sediments. Particular emphasis was concentrated on the evaluation and interpretation of the available geophysical data (gamma ray and resistivity logs), and geological information which had led to the establishment of several relationships between the local geology …

Go to article

Study Of Diagnosability Of Binary Address Decoders, Girishchandra Mahendrakumar Gandhi Jan 1969

Study Of Diagnosability Of Binary Address Decoders, Girishchandra Mahendrakumar Gandhi

Masters Theses

"This paper studies the diagnosability of various types of binary address decoders. An attempt is made to develop a theory of diagnosis for logical faults that might occur in these logic nets. The developed theory is used to analyze these logic nets for various input combinations. Finally, the derivation of optimum diagnostic test sequences is considered"--Abstract, Page i.

Go to article

Design, Construction, And Initial Experiments With High Hydrostatic Pressure Extrusion Device, Edward Moniz Jorge Jan 1969

Design, Construction, And Initial Experiments With High Hydrostatic Pressure Extrusion Device, Edward Moniz Jorge

Masters Theses

"The purpose of this study was to design and operate equipment with which the study of polymer extrusion would be possible at hydrostatic pressures up to 50,000 psi. By hydrostatic pressure is meant the pressure of the region of the extrudate. A study of the effects of back pressure on the extrusion of silicone gum was attempted--Abstract, Page ii.

Go to article

Stratigraphy And Correlation Of Precambrian Volcanic Rocks, Eminence, Missouri, Henry Hugh Fisher Jan 1969

Stratigraphy And Correlation Of Precambrian Volcanic Rocks, Eminence, Missouri, Henry Hugh Fisher

Masters Theses

"A portion of the Precambrian rocks located in the vicinity of Eminence, Missouri are studied and describes. These rocks are exposed as rhyolitic knobs protruding through hills of Ordovician sediments. The Precambrian rocks under study consist principally of rhyolite, with smaller amounts of tuff and creccis. The rhyolite is a potash rhyolite porphyry, both flow banded and unbanded, with phenocrysts of kaolinized orthoclase in a matrix of quartz and orthoclase. The tuffs contain devitrified glass shards and occasional ash balls such as those exhibited at Cott Mountain. A stratigraphic sequence was determined with the oldest rocks to the south at …

Go to article

The Incorporation Of Oxygen-18 Into Oxindole Acid By Cells Of Hygrophorous Conicus, William Green Allen Jan 1969

The Incorporation Of Oxygen-18 Into Oxindole Acid By Cells Of Hygrophorous Conicus, William Green Allen

Masters Theses

"To understand the mechanism of a biological oxidation in which oxygen is incorporated into a substrate, it is necessary to determine the origin of the incorporated oxygen. The objective of this investigation was to determine the origin of the oxygen atom incorporated into indoleacetic acid (IAA) by the IAA oxidase of Hygrophorous conicus through the use of oxygen-18. To determine the source of the oxygen atom incorporated into IAA it is necessary to incubate H. conicus cells with tryptamine or IAA in the presence of ¹⁸O₂ and H₂¹⁶O in one case and ¹⁶O₂ and H₂¹⁸O in another. An examination of …

Go to article

A Study Of A Lead Mining Waste Water Pollution Problem, William Earl Anderson Jr. Jan 1969

A Study Of A Lead Mining Waste Water Pollution Problem, William Earl Anderson Jr.

Masters Theses

"The waste water from the Fletcher Mine of the St. Joseph Lead Company was producing large algal growths in Bee Fork Creek. A field and laboratory study was conducted to determine the characteristics of the waste, find a method of determining the pollutional materials contained in the waste, study the undesirable algal growths, and develop and evaluate a practical, inexpensive, and effective pollution abatement method. Laboratory studies included analytical analysis of the waste, flotation reagent analysis, a microscopic study of the algal growths, algal growth studies, and heavy metal analysis of the algal growths. Field work comprised: a study of …

Go to article

A Five-Spot Waterflood Process As Applied To The Digital Computer Based On The Prats Technique, Leonard Koederitz Jan 1969

A Five-Spot Waterflood Process As Applied To The Digital Computer Based On The Prats Technique, Leonard Koederitz

Masters Theses

"The technique for the prediction of injection rates and production history of a five-spot secondary recovery field pattern as presented by Prats has been significantly modified to permit rapid and accurate digital applications eliminating the heretofore prohibitive reliance upon electrolytic model results for intermediate data values following water front breakthrough"--Abstract, page i.

Go to article

Numerical Simulation Of One-Dimensional Three-Phase Fluid Flow In A Stratified Petroleum Reservoir With No Cross-Flow, Ali Mohammed Akbar Jan 1969

Numerical Simulation Of One-Dimensional Three-Phase Fluid Flow In A Stratified Petroleum Reservoir With No Cross-Flow, Ali Mohammed Akbar

Masters Theses

"A numerical model for linear, three-phase fluid flow in a stratified petroleum reservoir has been developed for the purpose of studying water-flooding performance characteristics. Gravity forces, capillary pressure and cross-flow were neglected, but the fluids were considered compressible and evaluations of dissolved gas concentrations have been accounted for. The model was used in evaluating the performance of a water flood project for a hypothetical reservoir which contained the three phases of oil, gas, and water. The results were then compared with those obtained using the Dykstra-Parsons technique. The model produces results which were found to be similar to those obtained …

Go to article

A Continuous Method For Determination Of The Evaporation Rate Of Zinc, Paul Alan O'Neill Jan 1969

A Continuous Method For Determination Of The Evaporation Rate Of Zinc, Paul Alan O'Neill

Masters Theses

"A method for determination of the evaporation rate of zinc using a continuous recording balance has been devised. Tests were carried out under an inert gas over the range 600°C to 750°C with a total pressure of 1 atmosphere. It was found that the rate of evaporation doubled with an increase of 50°C in this range. Scanning electron microscope photographs show the crystalline nature of the condensate and the presence of a thin oxide layer on some solidified test samples. This oxide layer reduced the rate of evaporation by retarding the zinc vapor escape from the evaporating surface"--Abstract, Page iii.

Go to article

Simulation Of The Cyclic Steam Injection Process In A Petroleum Reservoir By A Finite Difference Mathematical Model, Jean-Claude Bernys Jan 1969

Simulation Of The Cyclic Steam Injection Process In A Petroleum Reservoir By A Finite Difference Mathematical Model, Jean-Claude Bernys

Masters Theses

"A three-phase, one-dimensional radially layered reservoir simulator is programmed for a large memory digital computer. It is designed to provide a practical solution to the problem of determining optimum soak time during an intermittent steam injection process. The general approach is to (1) develop a representative mathematical model which describes the reservoir; and (2) employ a suitable numerical technique to solve the system of equations which comprises this model. The reservoir consists of concentric cylinders around the wellbore, a pay-zone stratified into thermally connected layers limited on the top and on the bottom by an impermeable cap and base rock, …

Go to article

The Background Concentrations Of Copper, Lead, And Zinc In Streams Of The "New Lead Belt", Missouri, Nicholas Howard Tibbs Jan 1969

The Background Concentrations Of Copper, Lead, And Zinc In Streams Of The "New Lead Belt", Missouri, Nicholas Howard Tibbs

Masters Theses

"This study was initiated to determine the background concentrations of copper, lead, and zinc in the streams of the Viburnum Trend or New Lead Belt of southeast Missouri. Analytical methods were developed for atomic adsorption spectroscopy. These methods initially consisted of coextraction of cooper, lead, and zinc using the APDC/MIBK system, and finally of extraction of copper by APDC/MIBK and direct analysis of lead and zinc using the newly developed "Sampling Boat" technique. The data obtained from these analyses were arranged in histograms and critically analyzed. The background concentrations were established to be 4-6 ppb for all three elements. Methods …

Go to article

A Study Of The Correlation Potential Of The Optimum Moisture Content, Maximum Dry Density, And Consolidated Drained Shear Strength Of Plastic Fine-Grained Soils With Index Properties, Marvin Tartt Harris Jan 1969

A Study Of The Correlation Potential Of The Optimum Moisture Content, Maximum Dry Density, And Consolidated Drained Shear Strength Of Plastic Fine-Grained Soils With Index Properties, Marvin Tartt Harris

Masters Theses

"The correlation potential of the compaction properties and the consolidated drained shear strength parameters of plastic fine-grained soils with index properties was investigated in this study. The interrelationships of these properties were derived through graphical and multilinear regression analysis. The compaction properties, optimum moisture content, and maximum dry density were found to be related to many of the index properties. The most important relationships were with the plasticity indices and the percentage of particles smaller than two microns; the highest degree of simple correlation was achieved with the liquid limit. The consolidated drained shear parameters, cohesion, and the angle of …

Go to article

Anodic Oxidation Of Pure And D.S. (Dispersion Hardened) Lead In Sulfuric Acid Solutions, Rafael San Martin Aldazabal Jan 1969

Anodic Oxidation Of Pure And D.S. (Dispersion Hardened) Lead In Sulfuric Acid Solutions, Rafael San Martin Aldazabal

Masters Theses

"The anodic oxidation of pure and dispersion hardened lead in 1 N H₂SO₄ was studied potentiostatically in the range - 0.28 to 2.0 volts (SHE). The anode surfaces were observed at various stages on a scanning electron microscope and x-ray diffraction techniques were used to determine the phases present. It was established that by oxidation up to 0.25 v only PbSO₄ is obtained. At potentials between 0.25 and 1.57 v, PbO (tetragonal) is formed beneath the lead sulfate layer. At potentials above 1.57 up to 2.0 v, a layer of ßPbO₂ forms in the outermost part of the anode underlying …

Go to article

An Investigation Of Transient Negative Resistance In A Cadmium Sulfide Device, John Irvin Giem Jan 1969

An Investigation Of Transient Negative Resistance In A Cadmium Sulfide Device, John Irvin Giem

Masters Theses

"An analysis has been made of a CdS device which exhibits a transient negative resistance at room temperature and low field strengths whereas previously reported cases of negative resistance in CdS were observed at low temperatures and moderate to high electric fields. The CdS bar was illuminated on one end in the vicinity of an ohmic In contact. Contact was made to the other end of the device with a rectifying Ag contact and the device was reverse biased. Experimental evidence and the analytical results both indicated that it is necessary that the material used to make the negative resistance …

Go to article

Solution Of The Two-Dimensional Multigroup Neutron Diffusion Equation By A Synthesis Method, William Ray Heldenbrand Jan 1969

Solution Of The Two-Dimensional Multigroup Neutron Diffusion Equation By A Synthesis Method, William Ray Heldenbrand

Masters Theses

"A method, called the higher mode synthesis method, for the solution of the two-dimensional neutron diffusion equation is developed. In this method, the two-dimensional eigenfunction is expanded in terms of one-dimensional fundamental and higher eigenfunctions. A substitute, weight, and integration procedure is applied and the two-dimensional equation is reduced to a one-dimensional equation in terms of expansion coefficients. The expansion coefficients are combined with the trial functions in order to obtain the two-dimensional eigenfunction. This procedure results in a significant reduction of computation time as compared with standard iteration methods"--Abstract, page ii.

Go to article

Precipitation Hardening Of A Mg - 3.5 Wt. % Th - 1. Wt. % Mn Alloy, Adolf Chun-Chiung Huang Jan 1969

Precipitation Hardening Of A Mg - 3.5 Wt. % Th - 1. Wt. % Mn Alloy, Adolf Chun-Chiung Huang

Masters Theses

"The precipitation process in a Mg - 3.5 wt. % Th - 1. wt. % Mn alloy during aging at 260⁰, 350⁰ and 400⁰C was determined principally by transmission electron microscopy. At 350⁰ and 400⁰C, general precipitation of the equilibrium Mg₄Th phase moderately hardens the alloy. No transition lattice of this phase was seen. The Mg₄Th precipitate forms initially as disc shaped plates parallel either to the prism or basal plane of the matrix...During prolonged aging at 400⁰C the plates lengthen into long laths on either of the above planes in the close packed direction...At 260⁰C an unidentified G. P. …

Go to article

Method For Optimizing Multi-Layer Insulation, William Donald Morath Jan 1969

Method For Optimizing Multi-Layer Insulation, William Donald Morath

Masters Theses

"The use of multi-layer insulation can result in reduced material cost, weight, or volume. A method for selecting layer materials is described. Each layer material is selected to operate at its upper temperature limit and to contribute to the overall performance of the wall. The analyses required for optimizing flat and cylindrical walls are developed. Use of the digital computer makes it feasable [sic] to select layer materials from a large group of candidates. Fortran IV programs for optimizing flat and cylindrical walls are presented, and their use is demonstrated by the solution of example problems. Methods for improving the …

Go to article

An Analysis Of An Audio Amplifier Utilizing An Operational Amplifier And Negative Feedback, Anthony Francis Lexa Jan 1969

An Analysis Of An Audio Amplifier Utilizing An Operational Amplifier And Negative Feedback, Anthony Francis Lexa

Masters Theses

"An audio amplifier utilizing a monolithic operational amplifier is analyzed. The analysis is a block diagram approach where the amplifier is divided into three parts; operational amplifier, power amplifier, and feedback network. A Fourier series analysis is used to describe the distortion and signal components of the amplifier output. The results of this analysis demonstrate the advantage of large negative feedback on frequency response and harmonic distortion. Using relatively few passive components a high quality audio amplifier is constructed with an output power of 15 watts RMS power and negligible harmonic distortion"--Abstract, page ii.

Go to article

Analysis Of A Water Level Control, Bhupendra Girdharlal Shah Jan 1969

Analysis Of A Water Level Control, Bhupendra Girdharlal Shah

Masters Theses

"This thesis presents the analysis of a controller for a liquid level control system. The controller was built using an analog computer providing the ability to easily construct up to three modes of control. The controllers analyzed were: 1.) Proportional, 2.) Proportional plus reset, and 3.) Proportional plus reset plus preact. The system was tuned experimentally to provide satisfactory operation and root loci were also plotted to show the system stability for the three modes"--Abstract, page ii.

Go to article

Calculation Of Optimum Conditions For Simultaneous Heat And Mass Transfer In Porous Membranes, Chia-Chang Liu Jan 1969

Calculation Of Optimum Conditions For Simultaneous Heat And Mass Transfer In Porous Membranes, Chia-Chang Liu

Masters Theses

"The object of this investigation was to study desalination using evaporation through porous membranes and to estimate the economic potential of the method. The major factors affecting the economics were: 1. The saline water temperature into the evaporator, tsl; 2. the temperature driving force in the evaporator, DF; 3. the temperature driving force in the heat exchanger, DTEX; and 4. the saline water temperature leaving the evaporator, ts2. The optimum conditions based on cost of water product were studied by calculating water costs under a wide range of conditions. for any given set of variables t …

Go to article

Film Boiling From Inclined Flat Surfaces, Charles Ernest Price Jan 1969

Film Boiling From Inclined Flat Surfaces, Charles Ernest Price

Masters Theses

"The object of this investigation was to determine the effect of inclination on the heat transfer for saturated film pool boiling from a flat plate heater. Nitrogen at atmospheric pressure was used as the test fluid. The test plate was oriented at various angles from the horizontal position and the convective film coefficient was determined for each angle. Tests were conducted for heater angles of 0°, 30°, 60°, and 90°. The heater strip was placed in a container of the liquid and was heated electrically. Heat transfer results were obtained for plate temperatures ranging from 100 to 800°F. As the …

Go to article

Nuclear Parameter Study In One, Two, And Three Dimensions, Jan Robert Lojek Jan 1969

Nuclear Parameter Study In One, Two, And Three Dimensions, Jan Robert Lojek

Masters Theses

"A parameter study comparing one-, two-, and three-dimensional reactor design analyses was undertaken. Computer programs (codes) were used extensively for the computations and running times on the IBM 360/50 were observed. The values of primary concern were neutron flux shapes, effective multiplication factors, and fuel depletion. Dresden I nuclear power plant with fuel type 1 represents the model reactor. Cross section calculations were performed using the nuclear codes HRG and TEMPEST II, FEVER, EXTERMINATOR-2, AND FLARE generated the nuclear parameters"--Abstract, page ii.

Go to article

Michael Reactions Part Iv Syntheses With Carboalkoxycarbenes, Frederick Ralph Carman Jan 1969

Michael Reactions Part Iv Syntheses With Carboalkoxycarbenes, Frederick Ralph Carman

Masters Theses

"A preliminary investigation has been made involving syntheses with dicarboalkoxycarbenes for the purpose of developing new heterocyclic and alicyclic synthese employing functionalized carbenes. The ultimate goals were the development of a stereospecific synthesis of trans fused and angularly substituted ring systems suitable for conversion to natural products and the development of useful synthetic paths to the azabullvalene system. Although these ultimate goals were not realized, new and improved syntheses of alkyl substituted anisoles and diazomalonic esters, including the first reported synthesis of di-tert-butyl-diazomalonate were accomplished. The addition of dicarboalkoxycarbenes to di-, tri- and tetra- substituted ethylenes, tropilidene and 7-aza-tropilidenes by …

Go to article

Thermal Fatigue Testing Of Die Casting Die Steels, Kulwant Singh Sabharwal Jan 1969

Thermal Fatigue Testing Of Die Casting Die Steels, Kulwant Singh Sabharwal

Masters Theses

"Thermal fatigue is a form of surface failure produced by repeated thermal stresses and is the main cause of die retirement in the die casting industry. A general review of the fundamental and practical aspects of thermal fatigue as encountered in the dies, based on earlier published work, is given and preliminary experiments in an effort to set up a suitable method of testing to study this phenomenon are then described. In the present technique developed to create the thermal conditions experienced by a die steel in aluminum die casting, a small portion of one face of a cylindrical test-piece …

Go to article

Static And Dynamic Instability Analysis Of Rigid Frames With Timoshenko Members, Carlton Lee Smith Jan 1969

Static And Dynamic Instability Analysis Of Rigid Frames With Timoshenko Members, Carlton Lee Smith

Masters Theses

"In this thesis, a technique has been developed to determine the natural frequencies of plane rigid frames with the consideration bending, shear deformation, rotatory inertia, and internal axial forces. The internal forces are functions of the instability load of the vibrating system for which the effects of bending and shear deformation on the stability of this structure are considered. For the sake of completeness, the matrix formulations for the dynamic or stability analysis of a rigid frame are given. The stiffness matrices of these formulations are then derived. The influence of shear deformation, rotatory inertia, and internal axial force is …

Go to article

Further Investigation Of The Traveling-Wave Transistor, Robert J. Feugate Jan 1969

Further Investigation Of The Traveling-Wave Transistor, Robert J. Feugate

Masters Theses

"A brief introduction to the concept of a traveling-wave field-effect transistor is presented. Analytic solutions for certain lossless and lossy special cases are derived and a numerical method for solution of the general case developed. A possible computer program for implementing this numerically is given and utilized to compare the traveling-wave transistor to a conventional field-effect transistor amplifier"--Abstract, page ii.

Go to article

Vibration Of An Internally Damped Tapered Truncated Cantilever Beam, Chimanbhai Magandas Patel Jan 1969

Vibration Of An Internally Damped Tapered Truncated Cantilever Beam, Chimanbhai Magandas Patel

Masters Theses

"This thesis provides a vibration analysis of an internally damped, tapered, truncated, cantilever beam. Using two formulations of the problem based on: (1) Discrete mass and (2) continuous mass distribution, solutions are given for a beam having square cross section with linear depth and linear width variation. A Kelvin viscoelastic material for the beam is assumed. The vibration of the beam is considered to produce plane stress in the material, and the stress-strain relationship is applied only to the strain in the plane of bending. An exact solution for frequency of oscillation, mode shape, and steady state response is obtained …

Go to article

A Geochemical Study Of The Maquoketa Formation In Pike County, Missouri, John Siegfried Trapp Jan 1969

A Geochemical Study Of The Maquoketa Formation In Pike County, Missouri, John Siegfried Trapp

Masters Theses

"Statistical interpretation of geochemical data was used to determine the environment of deposition of the Maquoketa Formation in Pike County, Missouri. A cyclic sequence was noted which can be best explained by cyclic climatic changes. During the study it was found that elemental relationships which would be expected in a freshly deposited sediment can be found in core samples. In samples from outcrops and quarry faces these relationships have been destroyed. As these elemental relationships reflect mineralogical relationships, serious doubts have arisen as to the validity of petrographic studies of samples taken from outcrops. This study indicates weathering may be …

Go to article

First Prev Next Last