Digital Commons Network^™

A Study Of Missouri Flint Clay, Edmond Preston Hyatt

Masters Theses

"The problem is one of attempting to explain the peculiar nature of Missouri Flint Clay and to expand the knowledge concerning it. Among the questions for which answers are sought are: What makes Missouri Flint Clay so hard? What happens to Missouri Flint Clay when it is ground? What is the mineralogical constitution of Missouri Flint clay?"--Introduction, The Problem, page 1.

A Determination Of The Economic Feasibility Of Producing Marginal Gas Wells, Horace Tharp Mann

Masters Theses

"The purpose of this investigation is to show that it is economically feasible to produce marginal gas wells in such a manner that all the gas from the edge of the field will be captured by the first row of wells. In this problem the permeability of the sand is to be variable but known, and the effects of this variable permeability on the pressure distribution, and resulting gas production, will be discussed.

In many gas fields the point at which it is generally considered unprofitable to drill new wells is well inside the boundary of the reservoir. This is …

Calculations Of Maximum Sag Of A Transmission Line With An Ice Load On One Span, Rodney A. Schaefer

Masters Theses

"An important problem concerning electric power lines is the calculation of the maximum sag occurring when there is an ice load on only one span. The object of this thesis is to determine a practical method for calculating the maximum sag of a transmission line, suspended on suspension insulators, with the aforementioned loading conditions. This paper is limited to the case where the supports of the transmission line are at equal elevations and all span lengths are equal"--Introduction, page 1.

The Economic Spacing Of Contraction Joints In Reinforced Concrete Pavements, Wilbert Frederick Wegener

Masters Theses

"Structurally, there are two types of joints used in concrete pavements: (a) the tied, or permanently-closed joint; and (b) the open or free type of joint. The permanently closed joint utilized tie-steel of some form to keep the joint from opening. Usually, this steel is in the form of short individual bars extending across the joint and bonded to both slabs (designated as "tie-bars") or in the form of distributed reinforcement. The remaining method of classification, that of refering [sic] to the joint purpose, gives the expansion joint, contraction joint, and warping joint. An expansion joint is, as the name …

The Theory Of The Specific Heat Of A Body Centered Cubic Lattice, Curtis Cleveland Webster

Masters Theses

"In normal crystalline solids the atoms are at rest in their lattice points at absolute zero of temperature. Increasing the temperature of the crystal increases the motion of the atoms about their lattice points. Approximately, each atom or ion may be treated as a harmonic oscillator. then from the equations of motion of the atoms, by the Born-von Karman theory of specific heats, the normal modes of vibration of the lattice can be expressed as the roots of a secular determinant. Application of this theory to determine the thermodynamic properties of crystals has resulted either in solutions that are inaccurate …

A Study Of The Efficiency Of Split-Second Delay Electric Blasting Caps In Underground Limestone Mining, John B. H. Fitzwilliam

Masters Theses

"The introduction of electric blasting caps have delay intervals of the order of one-half to one second proved of advantage in many aspects of underground mining, particularly development work. Their use spread, until they now supersede fuse-and-cap firing wherever possible. Split-second delay electric blasting caps are a comparatively recent development from conventional delay caps. They have been found of practicable use in quarrying operations, and have been applied in many phases of underground mining. While evidence, to show that short-delay firing in quarrying is more efficient than instantaneous firing, is becoming increasingly conclusive, it remains to be proved that split-second …

Separation Of Cobalt From Zinc Sulfate Solutions By Synthetic Cation Exchange Resins, Wen-Hsiang Chang

Masters Theses

"The purpose of the present research is primarily to investigate the possibility of the separation and recovery of cobalt from zinc sulfate solutions by means of cation exchange resins. It is thought that such an investigation, seemingly of academic interest, might throw some light on determining the possibility of processing some industrial solutions containing both cobalt and zinc. Cobalt, for instance, has been well known as one of the most detrimental impurities in zinc electrolytic solutions. In spite of various purification treatments, small amounts of cobalt are often present in the electrolytic solution, causing a reduction in current efficiency and …

Reduction Of Zinc Sulphide In A Vacuum, Tien-Shih Liu

Masters Theses

"The successful large scale commercial application of high vacuum for high temperature metallurgical operations is a comparatively new development. The use of Pidgeon and the carbothermic processes for the production of magnesium during the war forced a perfection of both equipments and techniques for high vacuum operations. This opens broadly the way for a great expansion of vacuum metallurgy. Vacuum operation is thus no more a laboratory method - it is a kind of industrial practice. Many metallurgical operations, which cannot be carried out by ordinary processes, are made feasible when conducted in a reduced pressure. typical examples are the …

The Lithium Tungsten Bronzes, Shun Sheng Hsu

Masters Theses

"The 'tungsten bronzes are a series of anionic substitutional solid solutions of alkali or alkaline earth metal metatungstates and tungstic oxide. They are neither alloys or intermetallic compounds, the term "tungsten bronzes" was adopted because of their remarkable metallic properties -- e.g., high electrical conductivity, metallic luster on the crystal, and high specific gravity. Also owing to their intense and vivid colors and chemical inactivity it was possible to use them in the paint industry as a substitute for the so-called "bronze powders", the latter term is applied to the finely divided metal powders, such as aluminum, copper, brass, and …

Water Injection In The Modern Automotive Spark Ignition Engine, Leonard Carl Nelson

Masters Theses

"The injection of water in the spark ignition engine is not new. The effect of humidity in the air on the performance of the spark ignition engine probably initiated the early investigations. The water vapor in the inlet air decreases the speed of the flame front and necessitates spark advance to assure maximum power and maximum efficiency. Water particles in the air evaporate during the compression and combustion of the inducted charge and decrease the tendency of the engine to detonate. These effects are very evident when operating the spark ignition engine in a moist atmosphere. Water is not a …

Design And Construction Of An Electronic Gain-Phase Meter, Gabriel G. Skitek

Masters Theses

"There are many communication and electronic circuits, such as filters, phase-shifting networks, matching networks, voltage amplifiers with and without feedback, whose proper usage with associated equipment depends upon the knowledge of the variation with frequency of the voltage ratio and phase angle between the output and input sinusoidal voltages or currents...It is the purpose of this thesis to design and build an electronic instrument that will measure the voltage gain and phase angle between two sinusoidal voltages or current of communication circuits, in such a manner as to aid the student in visualizing how these quantities vary with frequency, and …

Analysis Of Cascade Of Four-Terminal Networks, Ernest Randolph Roehl

Masters Theses

"The object of this thesis is to find analytic expressions for the voltage and current variations along a structure composed of a cascade of identical dissymmetrical four-terminal networks driven harmonically at the sending end and working into an impedance at the receiving end and an impedance that can be placed at any of the junctions along the cascade. The method of analysis that is applied is analogous to that used in solving the long-line problem. A transmission system usually consists of the line or cable itself plus numerous other links whose purpose it is to correct defects in the line …

Aerodynamic Research For An Improved Rotor Control System On Helicopters, Delmar Wallace Breuer

Masters Theses

"Since the author has always been interested in Aeronautical Engineering, and in particular, rotary-winged-aircraft, the problem of research for aerodynamic improvement of rotary-wing control systems was chosen. This problem was suggested by the Army Aircorps Officials of Wright-Patterson Field of Dayton, Ohio as being a valuable and practical problem for the government. It is also valuable and practical for the author since it follows his general course of undergraduate study and since it fits closely into the field for which he is preparing himself...The requirement with which the author is most concerned is the design system for the producing of …

Analytical Investigation Of Thin And Moderately Thick-Walled Tubing Under Peripheral And Biaxial Loading, Frank Joseph Cizek

Masters Theses

"The problem then, resolves itself into a study of the behavior of thin-walled and moderately thick-walled cylinders under the effects of an external fluid pressure acting alone, or the effects of an external fluid pressure acting simultaneously with an axial loading. In this thesis a theoretical or analytical approach will be used. Some application and reference will be made to oil-well casings in particular, but the solutions will not be restricted to oil-well casing alone. it must be recognized that the tubing problem involves the problem of unstability before the proportional limit of the metal is exceeded and a similar …

The Application Of The Relaxation Method To The Solution Of Problems Involving The Flow Of Fluids Through Porous Media, Alexander Antoine Zwierzchowski

Masters Theses

"The purpose of this investigation is to determine the feasibility of applying the relaxation method of mathematical analysis to the solution of problems in rheology. The relaxation method was first introduced by R. V. Southwell who applied it to the problem of electrical conductivity. It was later used by M. W. Emmons to solve two-dimensional heat conduction problems. The steady-state flow of fluids through porous media can be difficult or impossible by the usual analytical methods even with rather simple boundary conditions. The relaxation method promises to provide an easier method of solution and to provide a means of solving …

Barium-Tin Alloys, James Richard Whanger

Masters Theses

"The author attempted to produce alloys of barium and tin using metallic barium and barium hydride. Also, an attempt was made to study the phase diagram using thermal analysis and X-ray investigation"--Introduction, page 2

Application Of Electrical Prospecting Methods To Two Types Of Sulphide Ore Deposits, Robert Van Nostrand

Masters Theses

"Although certain types of sulphide ores, especially those near the surface of the earth, lend themselves very well to electrical prospecting methods, quite the opposite is true of the extensive deposits of the type found in the Mississippi River Valley. The purpose of this investigation was to discover additional facts concerning two distinct types of sulphide ores, and therefrom to develop a new technique which would be applicable to prospecting for the lead and zinc deposits found in the Mississippi Valley"--Introduction, page 1.

The Effect Of Silicate Ion And Hydroxyl Ion On The Abstraction Of Potassium Ethyl Xanthate By Galena, Pao-Zung Wu

Masters Theses

"The purpose of this research was to investigate the effect of the silicate ion and the hydroxyl ion on the removal of potassium ethyl xanthate by galena; since the former ion is encountered during flotation owing to dissolution of silicates, and also sodium silicate being often used to disperse gangue minerals, and the latter one is encountered during floating in an alkaline circuit"--Introduction, page 1.

Analysis Of The Transit Traverse Survey Method Of The United States Department Of Interior, Geological Survey, Edward John Kimmick

Masters Theses

"This thesis was undertaken to ascertain the feasibility of incorporating the United States Geological Survey methods of surveying and computing into a course of study in the Civil Engineering curriculum. It has been the author's opinion that a course of study could be tendered, as a definite project, which incorporates fundamental surveying and advanced surveying. The author's planned course of study was a method of third order transit traverse survey streamlining the method used by the United States Geological Survey. The time element and weather were the essential factors in the planning. In the advanced surveying course there are eighteen …

Torque Characteristics Of High Speed Steel Twist Drills, Tien Chi Lee

Masters Theses

"The drill is the most efficient tool used by machinists, for in no other tool is the cutting surface as large in proportion to the cross sectional area of the body or part that is its real support. Drills have shared evolutionary developments from carbon steels to high speed steels and from flat to twist drills. Many investigations have been made on the twist drills, but due to the majority of their work being based on the size of drills from 1/2 to 1-1/2 inches or larger, there is a dearth of published data on the general problem of drills …

A Preliminary Investigation Of The Titanium-Copper Equilibrium System, August Robert Savu

Masters Theses

"The element titanium has a high degree of chemical activity at room temperature when in a finely divided condition. In the massive state this activity is only exhibited at high temperatures. The powdered metal is highly pyrophoric. Titanium forms quite stable sulphides and carbides, although these are subject to oxidation at high temperatures. It also form nitrides. Titanium being a transitional element forms hydrides with hydrogen which are stable at ordinary temperatures, but which dissociate at red heat liberating the hydrogen and leaving the metallic titanium in a very active state. Alloys are formed with such metals as aluminum, manganese, …

Automatic Wheel Balancer For Automobile Wheel, Frederick Eugene Nevin

Masters Theses

"Automobiles of today have been so constructed that greater speeds under safer conditions now exist. One of the improvements has been the low pressure tire. These tires carrying less pressure necessitates a casing of greater volume. This has created a tire of greater thickness in the axial direction but at the same time has decreased the diameter. Because of these innovations in present-day tires the author believes the wheel assembly (tire, tube, wheel, and brake drum) should be considered as a rotating cylinder not as a rotating disk. This being the case, the condition of dynamic unbalance is more critical. …

The Establishment And Analysis Of A Triangulation System For The Teaching Of Advanced Surveying, Philip Blaine Newlin

Masters Theses

"The first thought of establishing a triangulation system for the University of Arizona student work was conceived early in the fall of 1947, when the author first learned that he would be in charge of the advanced surveying field parties during the spring semester. These men were to be instructed in the accepted manner of conducting surveys of higher order. This would include the measuring of a base line of second or first order accuracy, the turning of horizontal angles with this same degree of accuracy, the determination of the azimuth of the lines by astronomical observations, the running of …

A Study Of The Power Consumption Of Mine Scrapers, Stanley Francis Johnsen

Masters Theses

"Since scrapers were first employed in underground mining work, numerous changes in scraper design have transpired until now there are several common types of scrapers in use in mines over the world. The proved models of scrapers have been developed over a period of more than fifty years. Although specific scrapers have been tested to determine the amount of power consumed, no literature could be found concerning the relative power consumption of the different types of scrapers when operated under identical conditions. Purpose of Problem - The purpose of this study is to determine the relative efficiency of different types …

A Graphic Method For Determining Pressure Losses Due To Air Friction In Mine Airways, Robert F. Bruzewski

Masters Theses

"One of the most important factors that influence the selection of a fan or blower for circulating a desired quantity of air through mine workings is the total pressure that is required to overcome the resistance of the airways. Ordinarily, the major portion of this resistance is that caused by friction of the moving air on the surface of the airways. The pressure that is required to overcome this frictional resistance is calculated by means of the friction formula"--Introduction, page 1.

A Correlation Of Formulas For The Flow Of Fluids In Pipes, John Gorman Duba

Masters Theses

"At present there exist two quite distinct fields in fluid flow in pipes, the one in water supply and the other in the petroleum industry. It is the purpose of this paper to discuss the various pipeline flow formulas as used in both fields and to correlate the exponential type formula which is much used in practice with the Nikuradse curves obtained in the laboratory"--A Brief Historical Review, page 5.

An Investigation Of The Amount And Kinds Of Material Pertaining To Safety Education To Be Found In Social Studies Textbooks, Dorothy D. Osborn

Masters Theses

Chapter I

Introduction

The Problem

In spite of the fact that safety education is acquiring a definitive place in elementary school curricula, there are still many secondary school educators who are indifferent to the need of including work in safety in the already crowded school program. However, our modern mode of living with its increased tempo and its concentration of population has intensified daily hazards to such an extent that the school must consider education for safety as part of its program. Time, effort, and money spent on education of children whose lives are to be taken in adolescence by …

Design Of A Radio Broadcasting Station, John William Hamman

Masters Theses

"In the design of any piece of equipment, before any work whatsoever is done, a reason for developing the object must be apparent to all concerned. Any expenditure of time, labor and money must be properly justified before action can be taken. In the case of this paper, then, the reason for designing a broadcast radio station for the Missouri School of Mines & Metallurgy at Rolla, Missouri is twofold: First, to provide an additional instrument whereby instruction may be given to students interested in the study of radio; second, to supply the residents of Rolla and vicinity with entertainment …

Dust Control In Mining Industry And Some Aspects Of Silicosis, Mathuramuthoo Subramanyam

Masters Theses

"The deleterious effect on human beings of dust in mine air is well-known. It is the duty of engineers, therefore, to take measures to eliminate it. It is now definitely established that of all the various types of dust encountered in mine air, silica dust is the most harmful. This dust, if inhaled over a period of time, causes the disease, silicosis, which in most countries is compensated for as a physical disability. The prevention of alleviation of this scourge is analyzed in three broad aspects: 1. If the mine air is as clean as outside atmospheric air, silicosis will …

A Comprehensive Traffic Survey For The City Of Rolla, Phelps County, Missouri, Leon Hershkowitz

Masters Theses

"The ultimate aim of this comprehensive traffic survey for the city of Rolla, Phelps County, Missouri, is to furnish a guide or pattern together with the necessary forms, maps and charts, that can be followed and reproduced by any city having a population of less than 10,000 in a study to determine its particular traffic problems. This survey should serve as a guide in determining what corrective action can be taken in connection with the following: (1) The improvement of location of state highway trunk [sic] routes, by-pass routes, auxiliary routes, and county roads in the city's immediate area. (2) …