Digital Commons Network^™

A Study Of The Relative Electric Resistance Of Commercial Steels And Pure Iron, William Eugene Wistehuff

Masters Theses

"The change in relative electric resistance of five commercial steels, Armco Ingot Iron and Pure Iron were studied over the temperature range of 800°C to 1100°C in an attempt to correlate the phenomena of hot or red shortness with a change in the Electric resistance .

The results from the above resistance measurements were compared with mechanical tests of the same steels to show that at the point at which the iron sulfide liquid forms there is a definite change in the slope of the electric resistance vs temperature curve.

Also studied was a discontinuity in the electric resistance vs …

Interaction Curve For A Beam Column., Mahendra Khushalchand Sanghavi

Masters Theses

"The theoretical interaction curve for a circular section is established. Experimentally the interaction curve f or a beam-column with a varying circular cross section, is established. The effect of stress history is discussed, and the comparisons of different interaction curves are made"--Abstract p.i

The Separation Of Strontium-90 From Cesium-137 And Fractionation Of Rare Earth Elements By Liquid-Liquid Extraction., Surendra D. Khanna

Masters Theses

No abstract provided.

The Effect Of Shear Deformation On The Slope Deflection Coefficients., Rajni C. Amin

Masters Theses

"This study was made to determine the effect of shear deformation on stiffness coefficients and carry over factors that are normally used in the calculation of moments in continuous beam or frames by the slope-deflection and Moment Distribution method.

Using the method of total strain energy, the vertical shear V and angle of rotation Ө caused by unit moment were determined for bending moment only and then determined for shear deformation plus bending moment, then carry over factors and stiffness coefficients were computed for each case. The relative effect of shear deformation is small for small depth ratio d_{b …}

Preparation Of The Cis And Trans Isomers Of Methylcyclohexanecarboxylic Acids And Their 2-Diethylaminoethyl Esters, Paul Allen Meulman

Masters Theses

Introduction

The purpose of this research is to prepare the CIS and TRANS isomers of the 2, 3 and 4-methylcyclohecanecarboxylic acids and their 2-diethylaminoethyl esters.

This series of compounds is of interest because of the anti-tumor activity shown by some ethanolamine derivatives. The compounds to be prepared in this study represent modifications of these structures to determine if further investigation in this area is worthwhile. A pharmacological evaluation of these compounds will be made since many esters of amino alcohols have demonstrated pharmacological activity. The cancer chemotherapeutic and pharmacological test results are not included in this paper, but will be …

An Analysis Of Some Of The Sociological Problems Involved In Guidance, Terry H. Fortman

Masters Theses

No abstract provided.

The Scientific Interests Of Robert Wilson Gibbes As Revealed In The Gibbes-Morton Correspondence, Phillip S. Swartz

Masters Theses

No abstract provided by author.

Developing A Musically Educated Person Through The Secondary School Band Program, Richard B. Boland

Masters Theses

No abstract provided by author.

A Preliminary Study Of The Dielectric Properties Of Bismuth Ferrate Ceramics., John Joseph Schwaller

Masters Theses

"In this investigation some of the results of Fedulov¹⁸ for a composition of 30 percent lead titanate - 70 percent bismuth ferrate were verified. The system of lead zirconatebismuth ferrate was studied with sintering data determined for the series. By X-ray and microscopic analysis the system was determined to be not a solid solution. The dielectric measurements show a linear relation between the dielectric constant and the percent lead zirconate from 100 percent BiFeo₃ to 10 percent BiFeo₃ - 90 percent PbZro₃"--Abstract, p. ii

Phase Extent Of Gaas, Gasb, And Insb, And Solid Solubility In The System Gaas-Gasb Determined By The Lattice Constant-Density Method., Chang Don Kim

Masters Theses

"The lattice constant of the homogeneous gallium arsenide varies from 5.65298A⁰ to 5.65J26A⁰ at 25° c with a change of composition in the range from 49-935 to 50.015 atomic percent gallium. The lattice constants of g allium and indium antimonide are 6.09592A⁰ and 6.47876A⁰ at 25 ° c, respectively and the extent of the phases of gallium and indium antimonide could not be found in this work.

The thermal expansion coefficient of gallium arsenide is 6.4 x 10^-6/⁰ C in the range between 10 and 65° c regardless of composition, ar.d those of …

Separation Of Radioactive Fission Products By Electrodialysis Using Aminopolycarboxylic Acids., Harry C. Hershey

Masters Theses

"The development of nuclear fission reactors to convert nuclear energy into electrical energy for use in industry, public utilities, military applications, and space exploration has resulted in ever increasing quantities of radioactive waste solutions. Significant reductions in nuclear fuel costs will be obtained when economical processes have been developed for recovery and purification of valuable fission products which are contained in radioactive waste solutions and are in demand for many research applications.

The United States Atomic Energy Commission has supported exhaustive studies to recover fission products by processes involving the more common unit operations such as extraction, distillation, crystallization, and …

Composite Beams In Building Constructions., Mahendrasinhji M. Jhala

Masters Theses

"The use of composite beams is very common in bridge and. in building construction due to the fact that a savings in material is effected.

The study herein shows a simplified procedure for design of composite beams. A number of design charts for rapid selection of a wide-flange section and the necessary cover plates are presented herein. These charts are based on economic sections of steel beams when used in a simple span, if one knows the approximate depth of the beam, slab thickness, allowable stresses in the steel and concrete and live load moment, it is very easy to …

The Sacajawea Formation And The Darwin Sandstone In The Southeast Wind River Mountains, Wyoming, Denny N. Bearce

Masters Theses

"The area under study is located along the southeast flank of the Wind River Range in Fremont County, Wyoming, Beds overlying the Madison Group are measured and described in six locations within this area. These locations are: Worth Fork Popo Agie River, Sink’s Canyon, Crooked Creek, Canyon Creek, Little Popo Agie River, and Cherry Creek.

Laboratory studies are used as an aid in correlating the sandstone and dolomite sequences described In the six sections. These studies include sieve and heavy mineral analyses and thin section examination.

Sorting factors, obtained from the sieve analyses, and heavy mineral suites indicate that the …

Thermocouple Shape Influence On Response In A Dynamic Compressible Fluid Atmosphere, Philip J. Steger

Masters Theses

"This investigation was performed to determine whether the geometrical shape of a thermocouple used to measure the temperature of a dynamic fluid atmosphere had any affect on its recovery factor and time response.

A converging nozzle was used to establish a dynamic fluid stream in which shaped silver solder junctions of copper-constantan thermocouples were tested. The velocity of the working fluid, air, was about 1000 ft/sec at the test point.

The investigation was successful, within experimental limits, in determining that the recovery factor of a bare thermocouple junction is not influenced by geometrical shape The results agreed substantially with available …

Experimental Stress Analysis Of Bolts In A Flange Coupling, Bansidhar Shah

Masters Theses

"This thesis deals with the strength of a bolted joint which is subjected to tensile and bending loads. The purpose of this investigation was to derive expressions for the stresses developed in the bolts and the load producing separation of the joint.

A laboratory study of a flange coupling was made and the behaviour of flange bolts under different clamping forces was studied in tension and bending tests. The strain in the bolt was measured by mounting the strain gages on the shank of the bolt. From this, a graph of applied load versus strain in the bolt was plotted. …

A Graphical Solution Method For The Tchebychev Elliptic Function Filter, Gene S. Luckfield

Masters Theses

"This thesis is concerned with the design of the Tchebychev elliptic function filter. The Darlington synthesis procedure is discussed and salient points from Darlington's paper needed for the design of this filter are presented.

It is shown that the design of the Tchebychev elliptic function filter requires a knowledge of the elliptic functions, particularly the elliptic sine. Since the use of these functions is not common, a brief review of their properties is presented.

Using the elliptic functions, a development of the equations describing the behavior of the Tchebychev elliptic function filter is given for the case of a normalized …

Investigation Of Stresses And Deflections In An Inclined Beam., Jayant Chhaganlal Soni

Masters Theses

"In this thesis an investigation has been made of the effect of inclination on strains and deflections in an inclined rectangular steel beam. To compute the strains and deflections Newmark's Numerical Procedure has been used. An experiment has been carried out on a rectangular steel beam for four different load increments and eight different inclinations. To compare the experimental and analytical data, graphs have been drawn for the experimental and analytical quantities of strains and deflections for all the four load increments and eight different angles of inclination. Results of the investigation indicate that the strains and deflections at inclinations …

A Study Of Rotational Critical Speeds For A Multi-Mass, Multi-Span System, Pravinchandra M. Upadhyay

Masters Theses

"It is well known that the unbalanced inertia forces present in rotating shafts set up violent vibrations in a transverse direction at certain speeds known as critical speeds, whirling speeds or whipping speeds. Therefore one who deals with the design of rotating machine parts, such as turbine rotors, multi-cylinder engine crankshafts etc., must consider transverse vibrations of rotating parts.

Practical solutions for finding the critical speeds of simple rotating systems, such as a single disk on a shaft with a single span, were derived by many authors. But as the number of loads and spans increases the problem becomes complex …

The Effect Of Reradiation On Heat Transmission, Arvindkumar M. Shah

Masters Theses

"In heat transmission by radiation, it is very easy to find the heat transmitted from one surface to another. Much work has been done in this area. The problem becomes complicated when the two surfaces are enclosed or joined by an enclosure. Such problems frequently arise in the design of furnaces. One problem is linked with the economy of fuel, by proper consideration of heat losses through the openings in furnace walls such as doors and burner openings. A second problem is associated with the heating capacity and useful heat transfer through the openings such as heat ports in walls …

The Location Of Underground Points By Means Of A Magnetic Dipole, Anthony Del Prete Jr.

Masters Theses

"The object of this study was to design, construct, and test an electromagnet that could, from an underground location, generate a magnetic field which could be located at the surface, and that was portable enough to be carried through a cave. This could then be used to locate points in a cave relative to the surface.

A 20 foot solenoid composed of four five-foot sections was built and magnetized by a lightweight rechargeable four-cell eight volt battery. The total weight of the equipment was 30 pounds.

The magnet was calibrated by erecting it and measuring its vertical intensity with a …

Stability Properties Of Various Predictor Corrector Methods For Solving Ordinary Differential Equations Numerically., Charles Edward. Leslie

Masters Theses

No abstract provided.

An Equilibrium Study Of The System Bi-S-H₂, Don Hie Lee

Masters Theses

"An experimental study has been conducted to determine the equilibrium behavior of the system Bi-S-H₂. The system was studied by equilibrating H₂-H₂S gas mixtures with Bi(l)- Bi₂S₃(s) two-phase mixtures at temperatures of 500°, 600°, 700° and 750°C in a circulating type equilibrium apparatus. The equilibrium gas mixtures were analyzed by a Fisher Gas Partitioner with a reproducibility of approximately 0.06 %.

A linear free energy equation has been derived from the results with an average deviation of ± 1 Kcal. This deviation is well within the accepted experimental accuracy for …

The Anodic Dissolution Of Zinc In Aqueous Solutions, Glenn E. Stoner

Masters Theses

"The increasing demand for protective metals as coatings and non-corrosive alloys has stimulated extensive research on the fundamental behavior of metals in corrosive media.

One of the problems still unsolved is the nature of the mechanism of the anodic dissolution of metals like zinc, magnesium, beryllium, cadmium, and aluminum in aqueous salt solutions. Several schools of investigators have proposed different and opposing theories to explain the discrepancies which often arise between coulometric data and the weight loss of metal electrodes in certain salt solutions.

The purpose of this investigation was to obtain experimental data for the anodic dissolution of zinc …

A Simplified Method Of Estimating Drilling And Blasting Costs Of A Highway Through-Cut Excavation In Rock, Donald J. Roberts

Masters Theses

"The development of cost estimating methods has been the most neglected phase of highway engineering. Overlooked in particular has been the development of an easily understood and easily applied method of estimating the costs of the drilling and blasting operations involved in a highway through-cut excavation in rock.

This investigation developed such a method by adapting and applying recent developments in the blasting planning field. The study was limited to small diameter blastholes and excavations in lifts of less than thirty feet. Normal efficient construction practices were presumed.

It was found from the investigation that the blast geometry and, subsequently, …

Viscosities Of Various Binary Non-Polar Gaseous Mixtures., Gerald Lee Stevenson

Masters Theses

"Viscosity is an important physical property involving the transport of momentum in a fluid. Momentum is transferred within a fluid under an existing velocity gradient as the driving force. Since momentum transfer is actually attained by the dynamic interaction between particles of mass, a description of molecular interaction is essential in order to accurately predict the viscosity of a fluid. Temperature affects fluid viscosity by increasing the kinetic energy of the fluid system and thus the frequency by which molecules are involved in interaction. There have been many theoretical studies made concerning the intermolecular potential energy statements which serve as …

Determination Of The Standard Free Energy Of Formation Of Zr₃S₂, Peter E. Otten

Masters Theses

"The Knudsen effusion method was used to find the equilibrium magnesium pressure for the reaction

3 Zr (s) + 2 MgS (s) = 'Zr₃S₂' (s) + 2 Mg (v)

By using known standard free energy data for the formation of magnesium sulfide and by using the equilibrium magnesium pressure, the standard free energy of formation of Zr₃S₂ was calculated and could be expressed by the equation

Δ F° = -139,800 + 49.13 T cal/mole

in the temperature range 900 to 1100°C.

It was also found that Zr₃S₂ was the zirconium …

Swelling Properties Of Putnam Soil, Oscar M. Palma

Masters Theses

"Volume change of Putnam soil under different moisture contents and the swelling pressure developed by the soil at the same moisture contents were investigated using standard test procedures.

The theory of one dimensional consolidation of Terzaghi was reviewed as well as the literature on swelling and swell pressure.

It was found that swell depends mainly on the initial water content, while swelling pressure depends mainly on the dry density of the soil"--Abstract, page ii.

The Design, Construction, And Calibration Of A Hydrodynamic Journal Bearing Testing Machine., John H. Roberts

Masters Theses

"The purpose of this investigation was to design, construct, and calibrate a journal bearing testing apparatus. The design, construction, and operation of the apparatus are described.

Two bronze bearings with length to diameter ratios of 1.0 and 0.5 were tested using a gravity oil reed system. The speed and the location of inlet oil supply were varied, and the resulting coefficients or friction, oil flow rates, outlet oil temperatures, bearing shell temperatures, and eccentricities of the bearings were determined. These results were evaluated and compared with theoretical solutions.

The results compared favorably with the theoretical solutions and substantiated the use …

A Thermodynamic Study Of The Molybdenum-Sulfur System At 1100⁰C, Seth C. Schaefer

Masters Theses

"A static method was used to determine equilibrium sulfur pressure for molybdenum-sulfur mixtures at 1100°C.

The results obtained were:
(1) The molybdenum disulfide phase was stable in a sulfur pressure range of 1.023 x 10^-5 to 6.026 x 10^-1 atmospheres. A range of non-stoichiometry from MoS_2.00 to MoS_2.22 was determined under these conditions.
(2) The upper limit of sulfur content of molybdenum sesquisulfide (Mo₂S₃) is nearly stoichiometric.
(3) The extent of solid solution of sulfur in molybdenum is approximately 1.5 atomic % (0.5 wt %).
(4) Molybdenum sesqu-isulfide (Mo₂S_{3 …}

Liquid Mercury Embrittlement Of Thin-Walled 2024 Aluminum Tubes, Edward J. Beckemeyer

Masters Theses

"The dislocation theory, Zener-Stroh crack model, and the Petch relationship, which correlates fracture stress and grain size, were used to analyze the embrittlement of 2024 aluminum alloy tubes by liquid mercury.

Surface energy ratios, [formula], were determined for biaxial stress ratios of 1/2, 1, ∞. The values of the surface energy ratios considered were 4.24, 1.79, 1.46, respectively. As part of this study, an approximate Nabarro-Peierls frictional stress was calculated for each stress ratio"--Abstract, page 2.