Digital Commons Network^™

Time Optimum Switching Zones In Multiple-Valued Control Systems, Jack Leroy Crawford

Masters Theses

"Present control system theory provides the criteria necessary to bring a second-order single-valued system to rest in a minimum time after a step input. The bang-bang type controller has been developed to obtain this optimum response.

However, existing theory fails to provide the necessary information to obtain the optimum response from a second-order rotational system when multiple values of angular position are allowed. This thesis extends the control theory to include these multiple-valued systems by showing the existence of what are called optimum switching zones. These zones predict which of the infinite number of switching curves in a multiple-valued system …

Optimalization By Peak-Holding, Curtis W. Dodd

Masters Theses

"The problem presented is a study of the peak-holding method of optimalization. This method applies to a system that has an extremum.

After describing how the complete system, consisting of the controller and the controlled system, works; variations in the controller are presented. These variations are changes in the final stage of the controller, the servo. A phase-plane analysis shows how the output of the controlled system varies with its rate of change. Limitations are presented which tell why the system cannot be kept at its peak value at all times. Finally an analog simulation is used to study the …

The Effect Of Plastic Deformations On Grain Boundaries., Jayendra Jamnadas Shah

Masters Theses

"The purpose of this study is to determine the effect of the plastic deformations on the grain boundaries and the grain structure of mild steel. Five beams tested were of A-36 steel and of 6 WF 20 rolled section. Central loading was used to develop a plastic tinge at the cent1:1r.

At the center, where a plastic hinge was formed, the effect of the plastic deformations on the grain structure was severe in all the samples taken from the tension side of all plastically or partially plastically loaded beams. In fully plastically loaded beams this effect had spread on both …

Effect Of Internal Pressure On Compressive Buckling Stress Of A Cylindrical Shell Under Eccentric Loading, Chao-Ping Chu

Masters Theses

“In this paper, an investigation was made of a thin- walled cylindrical shell under compressive load with various eccentricities and internal pressures to study the effect of the internal pressure on the compressive buckling stress of the shell.

So far, theoretical methods have not been devised to solve this problem; therefore, an experimental study was carried out. The experimental results indicated that the buckling load of the shell decreases as the eccentricity increases, that the buckling stress increases as the eccentricity increases, and that the change in buckling stress increases with an increase of internal pressure and is very nearly …

The Effect Of Cation Size Of Xanthate Collectors In Sulphide Flotation., R. W. Bourne

Masters Theses

"Batch flotation tests on Utah Copper ore were used to show the effect of collector cation size.

The results obtained were:

(1) Recovery of copper in the concentrate decreases with increase in the size of the collector cation.

(2) Increased recovery with ethyl over that for amyl with a given cation.

(3) No beneficial recovery with sulphur enriched xanthates.

Statistical techniques were used to ascertain if significant differences in results were present"--Abstract, p. i

Analysis Of Space Frames By Moment Distribution., Ting-Hwa Wang

Masters Theses

"This work presents an analysis of space frames and planar frames loaded in different planes by the method of moment distribution and the theory of superposition. From this analysis it is found that the torsional stiffness of frame members has a great effect on the final bending moments when twisting moments are applied to the frame. The analysis of space frames considering the forces, stresses, and moments in all three dimensions always yields a design more accurate and economical in material than the traditional planar frame analysis"--Abstract, p. i

Ground Magnetic Study Of The Anderson Ridge Quadrangle, Fremont County, Wyoming., Roland Lee-Ping Chen

Masters Theses

"The Anderson Ridge quadrangle is comprised of folded and faulted schist intruded by granitic, pegmatitic and basic igneous bodies. A ground magnetic survey was conducted using a torsion balance Radar Magnetometer of 15.5 gammas sensitivity to measure the vertical intensity variations. The results are presented on eleven profiles with accompanying generalized geologic cross-sections, two magnetic contour maps of 50 gamma interval, one with traverse line geologic control, and the second controlled by a geologic map of the area. A clear relationship exists between the vertical magnetic intensity distribution pattern and the known areal geology.

The susceptibility of the most common …

A Study Of The Phase Behavior Of Carbon Dioxide-Methane-Normal Decane Systems, Raja Audi Mansoor

Masters Theses

“The effect of carbon dioxide concentration, on solubility has been studied for several carbon dioxide-methane-n-decane systems. Experimental results were obtained using differential vaporization tests. Computational results were obtained using equilibrium constants.

The relation between solubility, bubble point pressure and solution carbon dioxide is presented. A ternary diagram showing the bubble point pressure behavior as a function of system composition is also presented”--Abstract, page ii.

A Preliminary Study Of The Controlled Crystallization Of A Bottle Glass., Narayan M. Sedalia

Masters Theses

The effect of addition of Ti0₂ as a nucleating agent was studied with a bottle glass composition of 74 weight percent Si0₂, l percent Al₂O₃, 5.4 percent Cao, 3.7 percent MgO, 15. 3 percent Na₂O, and 0.6 percent K₂O as a base or original composition. The addition of titanium dioxide ii varied from 3 to 20 weight percent. The composition of this bottle glass was changed by increasing the following ingredients and keeping the other ingredients in the same ratios:

1. Increased 5 weight percent of Al₂O …

High Order Bang Bang Control System., Shing-Chou Pi

Masters Theses

"The problem undertaken in this thesis is to find a representation of a nonlinear controller to minimize the response time of a limited input plant whose transfer function has N negative real poles. The extension of the phase-space method to automatic control systems described by high-order differential equations with a general high-order input is considered.

The design utilizes a maximum effort controller whose switching time is determined by the concept of switching hypersurfaces of the system in N-dimensional phase space and the concept of a distance function, which is & geometric length between the initial state point and the switching …

Velocity And Kinetic Energy Distribution Of A Submerged Jet., Patrick Shepard Couch

Masters Theses

"The velocity distribution in a cylindrically bounded region of water induced by a submerged axisynnnetric jet of water, has been investigated. Velocity profiles at successive levels were constructed. The continuity equation was shown to be only approximately verified by the velocity profiles.

The kinetic energy for each level was computed and given mathematical expression"-- Abstract, p. 2

Mass Transfer To Droplets: Effect Of Non-Newtonian Continuous Phase., Hsin Chih Wu

Masters Theses

"Since non-Newtonian fluids are frequently encountered in the chemical and process industries, it is important that the transport processes which are commonly encountered be thoroughly investigated. Although studies of fluid mechanics and heat transfer with these fluids have been reported, virtually no work has been reported in the study of mass transfer. This is particularly true of mass transfer in turbulent flow.

The purpose of this investigation is to study the liquid-liquid mass transfer phenomenon in turbulent flow associated with single droplets in non-Newtonian continuous phases. The results are compared with those obtained in Newtonian systems. The data obtained will …

Development Of A Fluor-Mica Dielectric Using Glass-Ceramic Fabrication Methods., James Joseph Tuzzeo

Masters Theses

"A tetrasilicic fluor-mica, K₂Mg₅si₈o₂₀F₄, was synthesized using glass-ceramic fabrication methods. Bubbles, rods, and disks of glass-mica were formed, and heat treated at selected temperatures between 620°c and 1160°c for various time periods. Density changes were correlated to mica content to determine the relative amounts of crystalline mica phase precipitated after heat treatment. Dielectric losses and dielectric constants of the glass-mica disks were measured for correlation to mica content"--Abstract, p/ ii

Investigation Of The Effect Of The Wall Thickness On The Residual Stresses Developed In Thick Wall Cylinders Due To Water Quenching From The Outside Surface., Ghanshyam Chandubhai Patel

Masters Theses

"This investigation has been made to determine the residual stresses in thick wall cylinders by the use of strain gages.

The cylinders were quenched from their outer surface i n water from a temperature of 1000°F, and the resulting residual stresses were determined by Sachs boring-out method. The effect of the wall thickness of the cylinders on the residual stresses and the error developed due to the boring operation were discussed"--Abstract, p. ii

The Prediction Of The Thermal Conductivity Of Various Binary Non-Polar Gaseous Mixtures., Chester Foon-Chen Feng

Masters Theses

"A simple method for predicting the thermal conductivity of binary non-polar gaseous mixtures from the force parameters of the pure components and composition was developed. The method is an extension of the application of the combining methods previously derived for viscosity predictions. Altogether, the published thermal conductivities of 683 binary non-polar mixtures at various temperature levels were compared with the corresponding calculated thermal conductivities resulting from the prediction method. The corresponding values predicted from Hirschfelder, Curtiss and Bird's expression were also compared.

Among the 683 binary mixtures, there were 138 di-di, di-poly, and poly-poly mixtures, 241 mono-

The Electrical Analogy Of Critical Speed For The Transverse Vibrations Of A Shaft With One, Two And Three Masses, Ashok Z. Patel

Masters Theses

"The object of this thesis is to determine the critical speed of a shaft by an electrical analogy. The shaft considered is of constant diameter and is simply supported at the ends by fixing it in self aligning bearings. The weight of the shaft is assumed to be proportionally distributed in the attached masses.

The original system is first of all converted to an equivalent simple spiring mass system by calculating the influence coefficients and hence frcan these determining the spring constants. The spring mass system obtained is then converted to an equivalent electrical circuit.

A sine-square wave frequency generator …

A Study Of The Separation Of A Mixture Of Carbon Dioxide And Hydrogen By Means Of An Orifice., Larry Gene Bauer

Masters Theses

"The purpose of the investigation was an attempt to verify a statement made by Partridge in an effort to discover a new method of separating gaseous mixtures. Partridge stated that when a constant pressure is applied on two gases of different specific gravity, a larger volume of the l igl1ter gas is forced through the orifice. Orifices of 1.016, 0.319, and 0.222 millimeter in diameter were used in the course of the investigation.

It was found that with the apparatus used in the research endeavor, no separation of the mixture of hydrogen and carbon dioxide could be obtained"--Abstract, p. i

Effect Of Hydroxyethyl Cellulose On Properties Of Concrete At Early Ages., Vipinchandra R. Shah

Masters Theses

"In this investigation, hydroxyethyl cellulose was used as an admixture in plain concrete. The admixture was tested for its effect on the compressive strength of plain concrete cylinders and for its effect on the flexural strength of plain concrete beams. Specimens were also tested for freeze-thaw durability and shrinkage.

The test results indicated that hydroxyethyl cellulose has the effect of increasing the compressive strength and decreasing the flexural strength of plain concrete. The rapid freezing and thawing tests showed that the durability increases with increase in amount of admixture.

The tests were carried out in the Materials Laboratory of the …

A Study Of The Crystallographic Orientation Dependence Of Electrical Resistivity In Zinc, Paul Frederic Becher

Masters Theses

"A potentiometer and galvanometer setup was used to obtain electrical resistivity data for polycrystalline zinc. Cold working textures were investigated by the reflection technique with a quadrant x-ray spectrometer.

Resistivity data were obtained for specimens that were reduced up to forty per cent from the as received condition, and the corresponding textures were studied. The results indicated that the resistivity change in the rolling direction is due to the reorientation of the c-axis in the rolling caused by cold working"--Abstract, page ii.

Structural Analysis Of Open Channels On Elastic Foundation., Wan-Cheng Liu

Masters Theses

"This study is to analyze continuous open channels used for fluid flow and supported on soil which is considered to provide an elastic foundation. The basic assumption is that the reaction forces of the foundation are proportional at every point to the deflection of the channel at that point. The walls of the channel are considered vertical in all cases but are subjected to various lateral pressures due to different embankment loading conditions"-- Abstract, p. ii

The Effect Of Communism On The Art Of Soviet Russia, Wilma Dell Tipsword

Masters Theses

No abstract provided.

Population And Family Planning In India, Mrudula Shah

Masters Theses

No abstract provided.

The Influence Of Dance On Ability To Jump In Basketball, Neveta Salmons

Masters Theses

No abstract provided.

An Investigation Of Motor Ability Tests With Application To The Battery Used By The Department Of Physical Education For Women At Eastern Illinois University, Lois Ann Loveland

Masters Theses

No abstract provided.

Effect Of Poly-Ethylene Glycol, A Non-Shrinking Agent, On Strength Properties Of Concrete., Vasantrai Vallabhbhai Desai

Masters Theses

"This thesis describes laboratory test made on plain concrete cylinders and ~earns for compressive strength, flexural strength, durability and shrinkage, using poly-ethylene glycol (ElOOO) as a non-shrinking admixture. The tests were conducted in the Materials Laboratory of the Civil Engineering Department.

The test results show that poly-ethylene glycol has the effect of reducing the compressive and flexural strength of plain concrete. The admixture also has the effect of reducing shrinkage, and reversing it, causing expansion with large percentage of its use. For the number of cycles of alternate freezing and thawing reported the admixture did not have any effect on …

Determination Of The Fast Flux Of U.M.R. Reactor, Dave Vibhakar Ratilal

Masters Theses

"Measurements of fast flux of University of Missouri at Rolla, Reactor have been made using: (n,p) reactions in Mg²⁷ and Ni⁵⁸ and (n,α) reactions in Al²⁷. The effective activation cross sections at respective threshold energies for various foils have been obtained from AERE and AECL reports and from literature published by various investigators. A RIDL 400 channel analyzer was used for counting"--Abstract, page 1.

Study Of The Temperature Dependence Of The Haeffner Effect In Mercury, Charles George Arnold

Masters Theses

“In 1953, E. Haeffner (1) reported that after he had passed a direct electric current through a capillary tube filled with mercury, he obtained a separation of the isotopes of mercury. It was found that the heavier isotopes were enriched at the negative terminal and the lighter Isotopes at the positive terminal. This effect has since been referred to as the Haeffner Effect. Since this original experiment, other investigators have observed this effect in many other liquid and some solid metal systems.

The work of J. N. Baysden (2) showed that the separation of the isotopes in mercury could be …

Use Of Sr-4 Strain Gages Under Hydraulic Pressure, Manubhai M. Patel

Masters Theses

"In this investigation an attempt has been made to determine the effects of hydraulic pressure on SR-4, type A-5 strain gages. A thick-walled aluminum alloy cylinder without end constraint was used to make an experimental study of the effects of hydraulic pressure on these strain gages.

The behavior of this cylinder under different internal hydraulic pressures was also studied by measuring the strains by means of strain gages which were attached to the inside and outside surface of the cylinder. The problem has been studied by applying pressures up to 4800 psi.

Because of the high internal fluid pressures various …

Minimum Frictional Characteristics Of Optimum Journal Bearings., Navinchandra F. Shah

Masters Theses

"This investigation was conducted to develop a graphical representation to determine the optimum bearing conditions for minimum friction and to establish a theoretical approach for journal bearing design.

A series of graphs has been plotted for· the coefficient of friction versus the eccentricity ratio based on the. Sommerfeld number derived from Reynolds' differential equation, f or optimum journal bearings.

The results obtained in this research have been compared with those developed by other investigators. This comparison confirms the validity of the results presented in this thesis, so that it could be used advantageously for the design of optimum journal bearings"-- …

On Optimum Receiver Using Decision Theory, Philip T. Tai

Masters Theses

“In recent years communication engineers have given increased attention to the study of communication through random media. The name random is used to describe a medium the properties of which are stated only in a statistical sense. For example the impulsive response of a certain medium may only be known as one of an ensemble of possible impulsive responses; the particular member of interest being drawn up according to some statistical rule. In other words there exists some "uncertainty" concerning the characteristic description of the medium. Significant work on these problems has been done by Price and Turin. Related work …