Digital Commons Network^™

Conceptual Design Of A South Pole Carrier Pigeon Uav, Kendrick M. Dlima

Master's Theses

Currently, the South Pole has a large data problem. It is estimated that 1.2 TB of data is being produced every day, but less than 500 GB of that data is being uploaded via aging satellites to researchers in other parts of the world. This requires those at the South Pole to analyze the data and carefully select the parts to send, possibly missing out on vital scientific information. The South Pole Carrier Pigeon will look to bridge this data gap.

The Carrier Pigeon will be a small unmanned aerial vehicle that will carry a 30 TB solid-state hard drive …

Design Of Structural Stand For High-Precision Optics Microscopy, Sara T. Novell

Master's Theses

Lawrence Livermore National Lab (LLNL) is home to the National Ignition Facility (NIF), the world’s largest and most energetic laser. Each of the 192 beamlines contains dozens of large optics, which require offline damage inspection using large, raster-scanning microscopes. The primary microscope used to measure and characterize the optical damage sites has a precision level of 1 µm. Mounted in a class 100 clean room with a raised tile floor, the microscope is supported by a steel stand that structurally connects the microscope to the concrete ground. Due to ambient vibrations experienced in the system, the microscope is only able …

Indoor Positioning Using Acoustic Pseudo-Noise Based Time Difference Of Arrival, Nicholas J. Luong

Master's Theses

The Global Positioning System (GPS) provides good precision on a global scale, but is not suitable for indoor applications. Indoor positioning systems (IPS) aim to provide high precision position information in an indoor environment. IPS has huge market opportunity with a growing number of commercial and consumer applications especially as Internet of Things (IoT) develops. This paper studies an IPS approach using audible sound and pseudo-noise (PN) based time difference of arrival (TDoA). The system’s infrastructure consists of synchronized speakers. The object to be located, or receiver, extracts TDoA information and uses multilateration to calculate its position. The proposed IPS …

Modeling Artificial Groundwater Recharge In The Santa Rosa Creek Watershed, Alexander J. Murray

Master's Theses

The Santa Rosa Creek Watershed is an approximately 48 mi2 large watershed located on the central coast of California. This watershed drains to the Pacific Ocean through Santa Rosa Creek as it passes through agricultural land and the town of Cambria. Historically the groundwater within the Santa Rosa Creek Watershed has been used for irrigation, municipal and domestic uses, and the creek is critical habitat steelhead trout. During dry years, there is less water for all uses. When low groundwater levels occur, water can be drawn out of the creek and into the soil, drying out steelhead habitat. Seven agricultural …

Solar Energy Generation Forecasting And Power Output Optimization Of Utility Scale Solar Field, Byungyu Kim

Master's Theses

The optimization of photovoltaic (PV) power generation system requires an accurate system performance model capable of validating the PV system optimization design. Currently, many commercial PV system modeling programs are available, but those programs are not able to model PV systems on a distorted ground level. Furthermore, they were not designed to optimize PV systems that are already installed. To solve these types of problems, this thesis proposes an optimization method using model simulations and a MATLAB-based PV system performance model. The optimization method is particularly designed to address partial shading issues often encountered in PV system installed on distorted …

Maturation And Culture Media Effects On In Vitro Bovine Embryo Developmental Competence, Ciara M. Helland

Master's Theses

In vitro produced bovine embryos are critical to the cattle industry. However, these embryos have altered morphology, epigenetics, and metabolism when compared to their in vivo counterparts. The aim of this thesis was to alter maturation and culture media to improve the developmental competence of in vitro bovine embryos. This thesis is comprised of three experiments and one proof of concept study. Each experiment followed the same general layout: oocyte aspiration from Jersey or Holstein ovaries, oocyte maturation for 24 hours, fertilization with bull semen for 24 hours, then embryo culture for 7-8 days in 38.5 °C in 5% O …

Thermal Modeling And Testing Of The Blue Thermal Vacuum Chamber, Madeline R. Jensma

Master's Theses

The Blue Thermal Vacuum Chamber (TVAC) located in the Space Environments Laboratory at California Polytechnic State University, San Luis Obispo (Cal Poly), may be used for thermal vacuum testing of test articles that fit with in the semi cylindrical test section that has a radius of approximately 18 cm and a length of 61 cm. The potential test articles include CubeSat systems and subsystem. The Blue TVAC can also be used for educational and research purposes. The goal of this thesis project is to develop a thermal model of the Blue TVAC to predict and analyze the thermal response of …

Using Generative Adversarial Networks To Classify Structural Damage Caused By Earthquakes, Gian P. Delacruz

Master's Theses

The amount of structural damage image data produced in the aftermath of an earthquake can be staggering. It is challenging for a few human volunteers to efficiently filter and tag these images with meaningful damage information. There are several solution to automate post-earthquake reconnaissance image tagging using Machine Learning (ML) solutions to classify each occurrence of damage per building material and structural member type. ML algorithms are data driven; improving with increased training data. Thanks to the vast amount of data available and advances in computer architectures, ML and in particular Deep Learning (DL) has become one of the most …

Design Of A Printed Circuit Board For A Sensorless Three-Phase Brushless Dc Motor Control System, Joshua Castle

Master's Theses

The use of brushless motors has increased in recent years due to superior performance characteristics compared with alternatives. The operation of a brushless motor is dependent upon a separate controller which is often in the form of a printed circuit board. As such, the size and performance capability of the controller can restrict the performance of the overall motor control system so advancements of these controllers further the potential use of BLDC motors. This project outlines the design of a PCB based, sensorless motor controller for operation of a three-phase BLDC motor powered by a 24 V, high current external …

Effect Of Polymer Design And Coating Formulation On The Water Uptake And Sensitivity Of Acrylic Water-Borne Films, William Z. Thompson

Master's Theses

Water-borne latex coatings represent a safer, more user-friendly, and environmentally responsible alternative to solvent-borne coatings, and are growing in popularity each year. However, these coatings often exhibit unfavorable performance when exposed to water for extended periods of time. This prolonged exposure often results in water uptake, which may give rise to other detrimental effects such as a decrease in modulus, blushing or water-whitening, reduced serviceable life, and softening of the film. In this study, various polymer composition latex design spaces are studied to develop an understanding of how water uptake can be modulated and minimized using common synthetic approaches. Factors …

The Design, Testing, And Analysis Of A Constant Jammer For The Bluetooth Low Energy (Ble) Wireless Communication Protocol, Aiku Shintani

Master's Theses

The decreasing cost of web-enabled smart devices utilizing embedded processors, sensors, and wireless communication hardware have created an optimal ecosystem for the Internet of Things (IoT). IEEE802.15.4, IEEE802.11ah, WirelessHART, ZigBee Smart Energy, Bluetooth (BT), and Bluetooth Low Energy (BLE) are amongst the most commonly used wireless standards for IoT systems. Each of these standards has tradeoffs concerning power consumption, range of communication, network formation, security, reliability, and ease of implementation. The most widely used standards for IoT are Bluetooth, BLE, and Zigbee. This paper discusses the vulnerabilities in the implementation of the PHY and link layers of BLE. The link …

Optimization And Longevity Of Functionalized Multi-Walled Carbon Nanotube-Enabled Membranes For Water Treatment, Madeleine Michael Isabella White

Master's Theses

Water scarcity is a growing concern at the global scale. Large scale water reuse is growing both in necessity and popularity. Before water reuse can be performed efficiently on a large scale or be used for potable supply, even indirectly, contaminants of emerging concern (CECs) will need to be treated at the full scale. Advanced oxidation processes (AOPs) are a form of advanced water treatment capable of treating a wide range of CECs. This study contributes to the growing field of AOPs and more specifically AOPs using ozone combined with functionalized multi-walled carbon nanotubes (MWCNTs). Ozonation of MWCNTs has been …

A Study Of The Standard Cirrus Wing Lift Distribution Versus Bell Shaped Lift Distribution, William H. Bergman

Master's Theses

This thesis discusses a comparison of the differences in aerodynamic performance of wings designed with elliptical and bell-shaped lift distributions. The method uses a Standard Cirrus sailplane wing with a lift distribution associated with the induced drag benefits of an elliptical distribution (span efficiency = 0.96) as the basis of comparison. The Standard Cirrus is a standard class sailplane with 15-meter wingspan that was designed by Schempp-Hirth in 1969. This sailplane wing was modeled and analyzed in XFLR5, then validated against existing wind tunnel airfoil data, and Standard Cirrus flight test data. The root bending moment of the baseline wing …

Design Of Prototype Prosthesis For A Canine With A Right Front Limb Deformity As An Alternate Approach To Stabilize Gait And Withstand Gait Forces, Tayler R. Kastlunger

Master's Theses

Congenital and developmental limb deformities in canines are rare and can occur as a genetic disorder or be caused by extrinsic factors. Without surgery to correct the deformity, conservative management can be implemented to manage exercise and restrict high-intensity activity of the canine. However, any alteration to the normal gait and locomotive biomechanics of a canine can have significant long-term effects on the musculoskeletal health and quality of life of the canine. To improve quality of life and provide an alternative and more cost-effective approach to surgery, a custom prosthetic was designed and developed for a canine born with a …

Investigation Of New Forward Osmosis Draw Agents And Prioritization Of Recent Developments Of Draw Agents Using Multi-Criteria Decision Analysis, Jodie Wei Yu

Master's Theses

Forward osmosis (FO) is an emerging technology for water treatment due to their ability to draw freshwater using an osmotic pressure gradient across a semi-permeable membrane. However, the lack of draw agents that could both produce reasonable flux and be separated from the draw solution at a low cost stand in the way of widespread implementation. This study had two objectives: evaluate the performance of three materials — peptone, carboxymethyl cellulose (CMC), and magnetite nanoparticles (Fe₃O₄ NPs) — as potential draw agents, and to use multi-criteria decision matrices to systematically prioritize known draw agents from literature for …

The Yanks Are Striking: Kern County, The 1921 Oil Strike And The Discourse On Americanism, Peter F. Hussey

Master's Theses

In the fall of 1921 oil workers of the San Joaquin Valley faced a post-war economic slump, wage cuts across the board and an increasingly hostile attitude of oil operators towards consultation with the federal government on labor relations. They voted to strike, and the next day eight thousand workers walked off the fields. Strikers crafted an image of “patriotic unionism,” underpinned by a faith in the federal government and the ideology of the American Legion. The strike did not end in gruesome class warfare like had been seen months earlier in the coal mines of West Virginia, but rather …

A Study Of The Utilization Of Panel Method For Low Aspect Ratio Wing Analysis, William Barton D. Newey

Master's Theses

This study demonstrates the applicability of using a modified application strategy of panel method to analyze low aspect ratio wings at preliminary design phases. Conventional panel methods fail to capture the leading edge vortex (LEV) that is shed by wings with low aspect ratios, typically below 2 depending on planform. This aerodynamic phenomenon contributes to a significant amount of the lift of these wings and the result is a drastic underestimation of the lift characteristics when analyzed by conventional panel method. To capture the effect of the leading edge vortex, a panel method code was used with an extended definition …

A Comparative Study On Seismic Analysis Methods And The Response Of Systems With Classical And Nonclassical Damping, Noah G. Bleichner

Master's Theses

This thesis investigated the application of seismic analysis methods and the response of idealized shear frames subjected to seismic loading. To complete this research, a Design Basis Earthquake (DBE) for a project site in San Luis Obispo, CA, and five past earthquake records were considered. The DBE was produced per the American Society of Civil Engineers’ Minimum Design Loads for Buildings and Other Structures (ASCE 7-10) and used for application of the Equivalent Lateral Force Procedure (ELFP) and Response Spectrum Analysis (RSA). When applying RSA, the modal peak responses were combined using the Absolute Sum (ABS), Square-Root-of-the-Sum-of-Squares (SRSS), and Complete …

Three Axis Attitude Control System Design And Analysis Tool Development For The Cal Poly Cubesat Laboratory, Liam T. Bruno

Master's Theses

The Cal Poly CubeSat Laboratory (CPCL) is currently facing unprecedented engineering challenges—both technically and programmatically—due to the increasing cost and complexity of CubeSat flight missions. In responding to recent RFPs, the CPCL has been forced to find commercially available solutions to entire mission critical spacecraft subsystems such as propulsion and attitude determination & control, because currently no in-house options exist for consideration. The commercially available solutions for these subsystems are often extremely expensive and sometimes provide excessively good performance with respect to mission requirements. Furthermore, use of entire commercial subsystems detracts from the hands-on learning objectives of the CPCL by …

Effect Of Endodontic Sealers On Dentin Strength, Philip Chang

Master's Theses

Introduction: The ideal endodontic sealer should be biocompatible, dimensionally stable, and have proper bond strength to dentin. The aim of this study was to apply a hoop stress to sectioned teeth discs which have been obturated with AH Plus sealer with no gutta percha, EndoSequence Bioceramic Sealer (BC Sealer) with no gutta percha, and Tetranite® with no gutta percha until fracture occurred and then compared the failure stresses.

Methods: Teeth were divided into three groups based on the sealer type used. The teeth were sectioned into 2 mm thick discs and load was applied using a piston until …

Review Of Mentoring Manuals In Stem To Improve The Mentorship Experience For Underrepresented Minority Students Through The Lens Of Social Capital And Combating Social Reproduction, Leno Kurimoto

Master's Theses

There is a lack of diversity and inclusion in STEM (science, technology, engineering, and mathematics) education. Students who pursue a degree in STEM, only less than half of them complete them. However, this phenomenon occurs at a greater percentage for underrepresented minority students (UMS). To combat the lack of representation in STEM, mentoring has been suggested to promote retention and minimize attrition. Mentoring provide plenty of benefits for students, as they can gain academic and professional experience. Unfortunately, mentorship of UMS is not the same compared to Asian and white students, thus different approaches and recommendations must be implemented to …

A Code Reputation System Using Ai And Blockchain Technology, Jeremy Chau

Master's Theses

Open source development is a method of development in which source code is developed using the combined skills of the public. A few examples of this sort of development would be the Chromium and Linux kernel projects hosted on GitHub. Open source development offers a wide variety of benefits and disadvantages. A main concern is when many people blindly trust developers without second thought. There is a lack of a rating system that judges those who develop code through open source means. This can call into question the quality of the code being written by the individual as well as …

Determination Of A Graph's Chromatic Number For Part Consolidation In Axiomatic Design, Jeffery Anthony Cavallaro

Master's Theses

Mechanical engineering design practices are increasingly moving towards a framework called axiomatic design (AD). A key tenet of AD is to decrease the information content of a design in order to increase the chance of manufacturing success. An important way to decrease information content is to fulfill multiple functional requirements (FRs) by a single part: a process known as part consolidation. One possible method for determining the minimum number of required parts is to represent a design by a graph, where the vertices are the FRs and the edges represent the need to separate their endpoint FRs into separate parts. …

Evaluation Of Silica Hydride Based Amide Stationary Phase For High Performance Liquid Chromatography And Aqueous Normal Phase Separations, Emma Tardiff

Master's Theses

With many modern chromatographic advancements, silica hydride based columns (also known commercially as Type-C) represent yet another evolutionary step in stationary phase development. Type-C silica hydride columns have the ability to retain both polar and nonpolar analytes and have the ability to behave in either RP or ANP modes of separation depending on mobile phase composition. A consequence of this increased stability is that Type-C columns can be used over a wide range of mobile phase compositions, from purely aqueous to purely nonpolar organic solvents, and any combination of the two. While the retention behavior of Type-C columns depends highly …

Using Stable Isotopes To Determine Foraging Areas Of Leatherback Sea Turtles: Limitations Of The Isotope Tracking Technique In The Western Atlantic Ocean, Sharon Hsu

Master's Theses

Reproductive output has long been linked to habitat quality and resource availability. Individuals foraging in high-quality habitats with high resource availability will have better body conditions and higher survival rates, as well as greater reproductive output. Post-nesting, Western Caribbean leatherback turtles are known to migrate to at least two foraging regions: the western North Atlantic and Gulf of Mexico. This study had three objectives: [1] measure δ13C and δ15N values in bulk skin tissue of females nesting in Parismina, Costa Rica to reveal prior foraging region; [2] assess influence of foraging region on female body size and reproductive output; and …

The Moderating Effects Of Gender And Occupation On Age Discrimination In Hiring, Rachel Su Windsor

Master's Theses

Over the years, ageism in the workplace has become an important topic. However, it remains unclear whether and how gender and occupation relate to age discrimination in hiring decisions. The current study addresses this issue by investigating job suitability ratings and selection decisions by comparing two hypothetical job applicants who differ in age (younger vs. older) and gender (male vs. female) for two occupations (software engineer vs. nurse) in two industries (high-tech and healthcare). This study employed a 2 x 2 x 2 incomplete mixed-factorial design, in which age was a within-subjects factor, and gender and occupation were between-subjects factors. …

The Relationship Between Perceived Overqualification And Job Attitudes And Behaviors: The Moderating Role Of Psychological Empowerment, Emily Colleen Meyer

Master's Theses

It has been shown that employees who perceive to be overqualified in their roles are more likely to display negative attitudes and behaviors; however, little attention has been paid to the possible moderators of this relationship. Therefore, the present study proposed that psychological empowerment would moderate the relationship between perceived overqualification and job attitudes (affective commitment and careerist attitudes) and behaviors (counterproductive work behaviors). It was hypothesized that the relationship between perceived overqualification and these job attitudes and behaviors would be weaker for employees with higher levels of psychological empowerment than for employees with lower levels of psychological empowerment. Results …

Noise Pollution, Environmental Justice, And Urban Green Space Accessibility: A Case Study In San José, California, Lauryn Duoto

Master's Theses

Noise pollution is an environmental stressor associated with a number of poor health outcomes. Promisingly, recent studies have identified urban green spaces such as public parks and community gardens as-built environments that can minimize noise pollution in the urban context. The objective of this project was to identify low-income communities of color that lack urban green space accessibility within the city of San José, California, to determine if sound level could be an indicator of urban green space usage and to evaluate whether urban green space can mitigate noise. Neighborhood demographics based on census tract data, including ethnicity and socioeconomic …

Auto-Landing System For Fixed-Wing Unmanned Aerial Vehicle, Dan Dermer

Master's Theses

Unmanned aerial vehicle systems, or any kind or autonomous system, are relevant to many applications today. However, they are complex and sophisticated systems that require a deep understanding of multiple technologies. In addition, the mathematical rigor, computer modelling, and programming applications involved make t¬his a challenging field of study. This thesis explores the possibility of achieving the automated landing of a fixed-wing unmanned aerial vehicle. Auto-landing systems can resolve the challenges for the novice user and make aerial vehicle platforms accessible and dependable. A wide spectrum of applications such as agriculture, aerial photography, and security, to name a few, can …

All Things Come To Pass, Brandon Luu

Master's Theses

All Things Come to Pass is a poetry collection consisting of 36 poems that revolve around the themes of impermanence, death, and memory. It is divided into three sections: Crisis, Melancholy, and Acceptance, inspired by the five stages of grief by Elisabeth Kübler-Ross. The poems are written primarily in free-verse and include genres such as elegy, pastoral, and narrative. The collection contemplates whether given the finite nature of life, in an existence where nothing lasts forever and everything seems ultimately inconsequential, what is it that should be considered important?