Digital Commons Network^™

Control Of Vortical Separation On A Circular Cone, Nikos J. Mourtos

Faculty Publications

For conical bodies, at moderate angles of attack, the flow separates from the lee side, forming two vortices. Although the vortex lift contrihution is highly desirable, as the angle of attack increases, the vortex system becomes asymmetric, and eventually the vortices breakdown. Thus, some control of the separation process is necessary if the vortex lift is to be exploited at higher angles of attack. The theoretical model which is used in this analysis has three parts. First, the 'single line-vortex' model is used within the framework of 'slender-body theory' to compute the outer inviscid field for specified separation lines. Second, …

Design Of The Laboratory Analog, Lsu Petroleum Engineering Research And Technology Transfer Laboratory

Faculty Publications

No abstract provided.

Visual Analog Study Of Fill-Hole Drifts, Lsu Petroleum Engineering Research And Technology Transfer Laboratory

Faculty Publications

No abstract provided.

Academic Freedom, Hate Speech, And The Idea Of A University, Rodney A. Smolla

Faculty Publications

No abstract provided.

Model-Based Estimation Of Wind Fields Over The Ocean From Wind Scatterometer Measurements. I. Development Of The Wind Field Model, David G. Long, Jerry M. Mendel

Faculty Publications

For pt.II see ibid., vol.28, no.3, p.361-373 (1990). A parametric model for near-surface mesoscale wind fields suitable for use in a model-based approach to estimate the wind field over a large region of the scatterometer measurement swath from measurements of the radar backscatter of the ocean's surface is discussed. The assumptions made in developing the model are described, and the accuracy of the resulting model is evaluated. The model is based only on scatterometer data and is computationally tractable, consisting of a linear equation relating the near-surface wind field to a vector of model parameters which is estimated from the …

Model-Based Estimation Of Wind Fields Over The Ocean From Wind Scatterometer Measurements. Ii. Model Parameter Estimation, David G. Long, Jerry M. Mendel

Faculty Publications

For pt.I see ibid., vol.28, no.3, p.349-360 (1990). The feasibility of a model-based approach to wind field estimation is discussed. In this approach the parametric model for near-surface mesoscale wind fields developed in pt.I is used. The parameters of the model are estimated from the wind scatterometer measurements; the wind field estimate is then computed from the estimated model parameters. Unlike the traditional pointwise approach, this approach takes advantage of the inherent correlation in the winds at different sample points to estimate the wind field more accurately and resolve directional ambiguity. The accuracies of wind field estimates obtained using the …

Federal And State Water Quality Regulation And Law In Missouri, Peter N. Davis

Faculty Publications

This article discusses that law in two parts. The first part examines the federal and Missouri waste discharge regulatory system. The second part analyzes common law rights and remedies related to water pollution.

Landscape Development And Coastal Wetland Losses In The Northern Gulf Of Mexico, R. Eugene Turner

Faculty Publications

The causes of the extensive (0.86%/yr; 288,414 ha/yr) and well documented dramatic and accelerating rate of coastal wetland loss in the northern Gulf of Mexico were investigated by an interdisciplinary university research team to discern the role of outer continental shelf development. The landscape changes and potential causal agents are emphasized herein. Natural driving factors include sea level rise and geological com- paction, which appear to remain constant this century, and sediment supply from the Mississippi River which has declined by 50%,since the 1950s. Man-made influences include hydrologic changes from river diversions, flood protection levees, an extensive canal and spoil …

Mississippi’S Furniture Industry Provides A Market For Forest Products, Steven H. Bullard

Faculty Publications

If you own timberland in Mississippi that has a hardwood component, you definitely should be interested in the furniture industry and the outlook for the use of wood in this market. The furniture industry provides a ready market for high quality hardwoods, as well as for lower quality hardwood timber; the outlook for the use of wood of both types is very favorable - particularly in the production of upholstered and non-upholstered furniture for household use.

Hearsay: Part Iii, Paul C. Giannelli

Faculty Publications

No abstract provided.

Lévy Laplacian Of Generalized Functions On A Nuclear Space, Hui Hsiung Kuo, Nobuaki Obata, Kimiaki Saitô

Faculty Publications

The Lévy Laplacian ΔF(ξ) = limN→∞N-1∑n = 1N 〈F″(ξ),en⊗ en〉 is shown to be equal to (i) ∝TF″s″(ξ;t)dt, where Fs″ is the singular part of F″, and (ii) 2limρ{variant}→0ρ{variant}-2(MF(ξ,ρ{variant})-F(ξ)), where MF is the spherical mean of F. It is proved that regular polynomials are Δ-harmonic and possess the mean value property. A relation between the Lévy Laplacian Δ and the Gross Laplacian ΔGF(ξ) = ∑n = 1∞=〈F″(ξ),en⊗ en〉 is obtained. An application to white noise calculus is discussed. © 1990.

Probing The Psychological Mystery Of Frankenstein, Paula R. Feldman

Faculty Publications

No abstract provided.

The Due Process Defense In Entrapment Cases, The Journey Back, Paul Marcus

Faculty Publications

No abstract provided.

Citizenship, Alienage, And Ethnic Origin Discrimination In Employment Under The Law Of The United States, Mack Player

Faculty Publications

INTRODUCTION

This paper will survey the federal law of discrimination in employment based on ethnic origin, alienage, and citizenship. There are a number of sources of this law, many of them overlapping. The federal constitution provides some protections, but only to governmental employees or applicants. The traditional centerpiece of employment discrimination law is Title VII of the Civil Rights Act of 1964. The 1866 Civil Rights Act also provides protection which overlaps with that provided by Title VII. Finally, the recently enacted Immigration Reform and Control Act of 1986 regulates both national origin discrimination, thus duplicating the protections of Title …

Rheology Of Aqueous Suspensions Of Polystyrene Latex Stabilized By Grafted Poly(Ethylene Oxide), Harry J. Ploehn, J. W. Goodwin

Faculty Publications

A water-soluble carbodiimide has been used to end-graft aminated poly (ethylene oxide)(PEO) chemically onto colloidal polystyrene particles. Two particle sizes (115 and 347 nm diameter) and two PEO molecular weights (112 000 and 615 000 g mol^–1) were combined to give suspensions with four different ratios of polymer layer thickness to particle radius. Electrophoresis demonstrated that the PEO was grafted, not just adsorbed. Dynamic light scattering showed that the adsorbed and grafted layers had similar structures and that non-ionic surfactant perturbed the PEO configurations. Steady shear and oscillatory rheometry indicated that long-ranged polymeric forces between particles governed the …

A Simple Model For A Zinc/Bromine Flow Cell And Associated Storage Tanks, G. D. Simpson, Ralph E. White

Faculty Publications

A simple model for a parallel plate, zinc/bromine flow cell and associated storage tanks is presented and used to make time-dependent predictions for various quantities in the system. The model is based on a previously published algebraic model of the cell at steady-state and time-dependent, first-order differential equations for the storage tanks. The Butler-Volmer equation is used for the electrochemical reactions, and the homogeneous reaction between bromine and bromide is included. The model predictions indicate that the charging operation of a zinc/bromine battery can be significantly improved by using a storage tank with a larger residence time for the bromine …

Mathematical Modeling Of An H2s Removal Electrolyzer, Z. Mao, P. Adanuvor, Ralph E. White

Faculty Publications

A mathematical model is presented for a high temperature H₂S electrolyzer. It is shown that the maximum current in this type of a cell is determined entirely by the transport rate of sulfide ions through the separator. It is suggested that this model could be used to determine the feasibility of various designs for this electrolyzer.

Electrochemical Behavior Of Graphite And Ni-Cr Electrodes In Sodium Polysulfide In The Absence And Presence Of Hydrogen Sulfide, Z. Mao, Ralph E. White, B. Dandapani, A. Anani, S. Srinivasan, A. J. Appleby

Faculty Publications

The electrochemical behavior of graphite and Ni-Cr electrodes in sodium tetrasulfide melt has been investigated using voltammetric, chronoamperometric, and chronopotentiometric techniques in the presence and absence of hydrogen sulfide. Two continuous phases, namely, Na₂S₂ and Na₂S, are apparently formed at different potentials during the cathodic polarization. The blocking effect by these layers was much less significant on the Ni-Cr electrode than on graphite. The presence of H₂S did not appear to influence the electrode reactions, but it significantly reduced the rate of formation of the continuous phases (Na₂S₂ or Na …

A Computer Simulation Of The Oxygen Reduction Reaction In Carbonate Melts, P. K. Adanuvor, Ralph E. White, A. J. Appleby

Faculty Publications

A computer simulation of the oxygen reduction reaction in various carbonate melts has been carried out under steady-state conditions on the basis of a proposed kinetic model which takes into consideration the autocatalytic reaction involving oxygen and other reducible oxygen species in the melt, and the neutralization of oxide ions by dissolved carbon dioxide. A simulation of the presence of (physically) dissolved oxygen, in the diffusion layer region of the melt, corresponding to the possible situation in porous electrodes, causes a significant enhancement in the polarization curves, particularly in the mass-transfer control region. On the other hand, high levels of …

Estimation Of The Diffusion Coefficient And Solubility For A Gas Diffusing Through A Membrane, Michael C. Kimble, Ralph E. White, Yu-Min Tsou, R. Neal Beaver

Faculty Publications

Analysis of the data obtained by the electrochemical monitoring technique for diffusion of a gas through a membrane is considered. It is shown that combining a numerical method with a nonlinear parameter estimation technique provides a means to determine values for the diffusion coefficient and the solubility of the diffusing gas. It is shown that better accuracy can be obtained for the diffusion coefficient and solubility of this gas by using the method presented and all experimental data rather than only part of the data, as has often been done in the past.

The Reservation As Place: A South Dakota Essay, Frank Pommersheim

Faculty Publications

No abstract provided.

Predicted Secondary Current Distributions For Linear Kinetics In A Modified Three-Dimensional Hull Cell, F. A. Jagush, Ralph E. White, William E. Ryan

Faculty Publications

Current density distribution is an important consideration
for those involved in designing electrochemical systems
and electroplating systems in particular. Although it
is important, the common practice in industry is to use
trial and error to determine designs that optimize current
density distributions in electroplating. The purpose of this
paper is to illustrate the use of the finite element method
(FEM) to predict three-dimensional current density distributions.

Mathematical Model Of A Lithium/Polypyrrole Cell, Taewhan Yeu, Ralph E. White

Faculty Publications

A mathematical model to simulate the charge/discharge behavior of a lithium/lithium perchlorate-propylene carbonate/polypyrrole(Li/LiClO₄-PC/PPy) secondary battery cell is presented. The model can be used to gain a better understanding of the behavior of this cell and to provide guidance toward the design of new secondary batteries which utilize an electronically conductive polymer such as polypyrrole (PPy) as the cathode. The model includes the capability of handling charge and discharge behavior and is used to study the effect of various design parameters on the performance of the cell.

Three-Dimensional Current Distributions In A Bipolar, Chlor-Alkali Membrane Cell, Ralph E. White, F. Jagush, H. S. Burney

Faculty Publications

The current distributions in a stack of bipolar, membrane
chlor-alkali cells are important design considerations
(1). The degree of nonuniformity of the current distribution
is important to know because highly nonuniform
current distributions could cause, among other things, severe
damage to the membrane in a cell stack (2).

Electrochemical Production Of Hydrogen And Sulfur By Low-Temperature Decomposition Of Hydrogen Sulfide In An Aqueous Alkaline Solution, A. A. Anani, Z. Mao, Ralph E. White, S. Srinivasan, A. J. Appleby

Faculty Publications

Electrolysis of hydrogen sulfide to its constituents in a solution containing equimolar concentrations of NaOH and NaHS has been carried out at 80°C. In a double-compartment cell employing Nafion membrane as a separator, both crystalline elemental sulfur and high-purity hydrogen have been produced at high current efficiencies. Only minimal, if any, passivation of the anode by sulfur product was observed. According to solution composition, electrolysis could result in gas evolution at the anode, passivation of the anode by sulfur deposition, or oxidation of sulfide (S^2–) or polysulfide (S) to sulfur oxyanions. However, in an optimized solution, electrolysis gave …

The Effects Of Separator Design On The Discharge Performance Of A Starved Lead-Acid Cell, T. V. Nguyen, Ralph E. White, Hiram Gu

Faculty Publications

A mathematical model of a starved lead-acid cell has been developed to study the dynamic behavior of the cell during discharge. Concentrated binary electrolyte theory and a volume-averaging technique were used to model the transport of electrolyte. The model can be used to predict cell voltage and profile of: acid concentration, overpotential, porosity, reaction rate, and electrode capacity, as functions of time. The effects of separator thickness and its porosity were examined with respect to cold-cranking amperage and reserve capacity of the battery. The separator was found to be a significant factor governing performance.

Teaching In A Liberal Arts College: How Foreign Language Courses Contribute To "Writing Across The Curriculum" Programs, Ilona Klein

Faculty Publications

This essay shares some thoughts about the need for interaction between foreign language instructors and English teachers, both in high schools and at the university level. As a foreign language teacher for the past nine years (the last four in a liberal arts college), I have encountered several problems and difficulties that could be overcome, I believe, if English, Writing, and Foreign Language departments addressed them together. I do not claim to be able to give definite answers, since many pedagogical concepts concerting L2 acquisition/learning and their possible application to writing programs remain misunderstood or are presently debated by teacher …

Lottery Proceeds In California Pay For Installation Of A Ground-Water Monitoring System, June Ann Oberdorfer, J. W. Williams, M. G. Smelser

Faculty Publications

No abstract provided.

Diffuse Absorbing Beryllium Coatings Produced By Magnetron Sputtering, David D. Allred, C. M. Egert

Faculty Publications

Beryllium coatings with varying thicknesses and columnar grain sizes were deposited by low temperature magnetron sputtering and wet chemically etched to enhance diffuse absorption of light. After etching these coatings exhibited a matte black surface finish and low specular reflectance (below 2%) in the IR up to a critical wavelength dependent upon the original grain size of the coating. Extremely thick coatings (350 µm) with original grain sizes of 10 to 12 µm were produced which exhibited specular reflectances below 0.5% up to 50 µm wavelength and a Lambertian BRDF at 10.6 µm averaging 4.3x10-3 ster-1. Scanning electron micrographs are …

Advanced Infrared Optically Black Baffle Materials, David D. Allred, Ronald D. Seals, C. M. Egert

Faculty Publications

Infrared optically black baffle surfaces are an essential component of many advanced optical systems. All internal surfaces in advanced infrared optical sensors that require stray light management to achieve resolution are of primary concern in baffle design. Current industrial materials need improvements to meet advanced optical sensor systems requirements for optical, survivability, and endurability. Baffles are required to survive and operate in potentially severe environments. Robust diffuse-absorptive black surfaces, which are (1) thermally and mechanically stable to threats of x-ray, launch, and in-flight maneuver conditions, with specific densities to allow an acceptable weight load, (2) handleable during assembly, (3) cleanable, …