Digital Commons Network^™

Fatigue Analysis From Strain Gage Data And Probability Analysis, Robert C. Deen, James H. Havens

Kentucky Transportation Center Research Report

The Central Bridge over the Ohio River between Newport, Kentucky, and Cincinnati, Ohio, was completed in 1891 and in 1972-73 was considered to be in danger of fatigue failure. A series of investigations were undertaken to determine the likelihood of failure and to estimate the time of probable failure. During the investigation, a methodology was developed to determine fatigue damage from a probability analysis of traffic data by reconstituting or synthesizing the load (traffic) history of bridges. Strain gage data obtained with Prewitt scratch gages and SR-4 resistivity gages were used to evaluate fatigue damage incurred by the Central Bridge.

Identification Of Hazardous Rural Highway Locations, John A. Deacon, Charles V. Zegeer, Robert C. Deen

Kentucky Transportation Center Research Report

An effective procedure was determined for identifying hazardous rural highway locations based on accident statistics. Multiple indicators of accident experience that are necessary include the number of fatal accidents, the total number of accidents, the number of effective-property-damage-only accidents, and the accident rate. Critical levels of these four indicators should vary from state to state depending on the nature of the local safety improvement program as well as local traffic and roadway conditions and prevailing attitudes toward highway safety. Specific recommendations are given for use in Kentucky. Critical accident rates are established using quality control procedures.

To identify hazardous highway …

Accidents On Rural Interstate And Parkway Roads And Their Relation To Pavement Friction, Rolands L. Rizenbergs, James L. Burchett, John A. Deacon, Cass T. Napier

Kentucky Transportation Center Research Report

Friction measurements were made with a skid trailer at 70 mph (31 m/s) on 770 miles (1240 km) of rural, four-lane, controlled-access routes on the interstate and parkway systems in Kentucky. Each construction project was treated as a test section. Accident experience, friction measurements, and traffic volumes were obtained for each. Various relationships between wet-weather accidents and skid resistance were analyzed. Averaging methods were used as a means of developing trends and minimizing scatter. A moving average for progressively-ordered sets of five test sections yielded more definite results. The expression of accident occurrence which correlated best with skid and slip …

Adaptation Of Aasho Interim Guide To Fundamental Concepts, Herbert F. Southgate, Robert C. Deen, James H. Havens

Kentucky Transportation Center Research Report

Using 1971 vehicle classification counts and truck weights from nine Kentucky locations, equivalent axleloads (EAL's) were calculated by several methods. Apparent discrepancies led to a review of axleload equivalency factors used to estimate either EWL's (equivalent wheel loads) or EAL's.

Axleload equivalencies are determined as the ratio of the number of repetitions of a standard or reference load to the number of equivalent (damage-wise) repetitions of the load in question. The choice of equivalency factors can result in as much as a 40-percent difference in calculated EAL's. Most of Kentucky's traffic is made up of axleloads less than 80 kilonewtons …

Evaluation And Modification Of The Traffic Noise Prediction Procedure For Kentucky Highways, Kenneth R. Agent, Charles V. Zegeer

Kentucky Transportation Center Research Report

Approximately 270 noise-level recordings were obtained at 39 highway sites and compared with the noise-level predictions obtained by the procedure outlined in NCHRP Report 117. The measured noise levels were computed in terms of the A-weighted L₁₀ value (level exceeded 10 percent of time) and then compared to the predicted noise levels. A significant discrepancy was found between predicted and measured noise levels; generally, the predicted values exceeded the measured values. Average error per location was 4.8 dBA; the maximum error was 13 dBA. A nomograph was devised to correct the predicted value; this nomograph involves observer-to-roadway distances, truck …

Highway Pavement Maintenance Costs And Pavement Type Selection, Donald C. Newberry Jr., Jesse G. Mayes, James H. Havens

Kentucky Transportation Center Research Report

A long-term analysis of pavement maintenance cost has been performed. The analysis does not include construction or resurfacing costs. The sample of pavement sections investigated were chosen to best represent the entire state. These sections were classified by pavement type; either bituminous concrete, portland cement concrete, or composite. The cost per lane mile (kilometer) per year was calculated for each pavement type by year and by age of pavement. Apparent differences in pavement maintenance costs between the two basic types of pavements were adjudged insignificant from the standpoint of determining pavement type. Because of poor or erroneous cost reporting, actual …

Relationships Between Roadway Geometrics And Accidents, Kenneth R. Agent, Robert C. Deen

Kentucky Transportation Center Research Report

Statewide average and critical rates of accidents were determined from 1970-1972 Kentucky accident records for each type of rural highway. Accident data, obtained from state police computer tapes, were summarized to give the number of accidents on each highway type as well as information on accident severity, road surface conditions, light conditions, road character, and type of traffic control. Four-lane undivided highways had the highest average accident rate; parkways (toll roads) had the lowest rate. The severity of accidents was related to types of accidents, highways, and traffic control and to safety belt usage. Accidents involving pedestrians were the most …

Rock Evaluation For Engineered Facilities, D. J. Hagerty, Robert C. Deen, M. W. Palmer, C. D. Tockstein

Kentucky Transportation Center Research Report

The need for comprehensive information on the characteristics and behavior of earth materials has been recognized for many years, perhaps for as long as significant construction has taken place in and on the surface of the earth. In recent years, however, the magnitude and complexity of engineered construction has greatly increased, resulting in a corresponding increase in the need for information on the engineering properties of soil and rock materials, Direct testing of soil and rock can be utilized to furnish necessary information. However, both field and laboratory testing can be extremely expensive, particularly where testing must include applications of …

Bridge Decks Constructed For Increased Durability, Assaf S. Rahal

Kentucky Transportation Center Research Report

The experimental features incorporated in this study were compaction, brooming, and hi-layered construction. Broomed surfaces initially exhibited a higher skidding resistance than non-broomed surfaces: broomed surfaces, however, wear more rapidly. No conclusive evaluation could be made at this time of the bilayered system and of tests made on the concrete cores. Electrical measurements made on the decks indicated there was no active corrosion of the steel.

Effects Of The Energy Crisis On Traffic In Kentucky, Kenneth R. Agent, Donald R. Herd, Rolands L. Rizenbergs

Kentucky Transportation Center Research Report

The Arab oil embargo in mid-October 1973 curtailed availability of gasoline. Fuel conservation measures resulted in reduced travel and decreased traffic speeds. On March 1, 1974, posted speed was set at 55 mph on rural highways in Kentucky. Traffic volumes, speeds, and accidents for the rural highway during the period known as the "energy crisis" and its after effects were compared to the corresponding period a year earlier.

Traffic volumes began to decline in December 1973 but began to rise again in March 1974. Total travel in the seven months through June 1974 decreased by 3.5 percent; traffic increased by …

Experimental Portland Cement Concrete Shoulders Design And Construction, James H. Havens, Assaf S. Rahal

Kentucky Transportation Center Research Report

Kentucky's first portland cement concrete shoulder project was conceived in 1970 and was inspired by the Portland Cement Association's issue Concrete Shoulders for Safe Modern Highways, Concrete Report, 1970, and FHWA's Informational Memorandum CMPB-17-70, Experimental Project for the Evaluation of Portland Cement Concrete Shoulders Adjacent to Concrete Mainline Pavement; Project Prospectus, National Experimental and Evaluation Program; May 12, 1970. It was expected that at least two states in each region would participate in the national program. A 3.442-mile section of US 31 W, between Radcliff and Tiptop, beginning at the intersection of US 60 and extending southward, …

Skid Resistance Studies In Kentucky (An Overview – 1974), James H. Havens, James L. Burchett, Rolands L. Rizenbergs

Kentucky Transportation Center Research Report

"To free Kentucky of slick roads" is the high goal toward which Kentucky has been striving since 1950's. A very capable fellow engineer used to say that there was more satisfaction in being able to take down a Slippery When Wet sign than in erecting one.

Considerable effort has been devoted to the development and adaptation of improved methods of skid resistance testing and to the standardization of testing devices (1, 2, 3, 4). Methods of tests have included the NCSA friction wheel (bicycle wheel), automobile deceleration, skewed-wheel (skewed front-wheels of an automobile), skidding automobile, and the skid-test …

Metabolic Capabilities Of Sulfur Oxidizing Bacteria And Their Role In Water Pollution, M. I. H. Aleem

KWRRI Research Reports

This report describes investigations into the physiology of microorganisms that are commonly involved in the oxidation of inorganic sulfur compounds. The metabolic activities of these bacteria play a potent role in several fields of economic importance such as strip mining operations, water pollution, corrosion, metallurgy, petroleum technology and soil fertility processes.

The oxidation of inorganic sulfur compounds was studied in the chemolithotrophs Thiobacillus denitrificans, Thiobacillus A₂, Thiobacillus neapolitanus, and a photolithotroph Rhodopseudomonas palustris. Cell suspensions from all of the thiobacilli catalyzed completely the oxidation of sulfide, thiosulfate, and sulfite to sulfate. The oxidation of thiosulfate in R. palustris …

Powers Of The State Of Kentucky In Implementing An Effluent Tax As A Part Of An Interstate Ohio River Basin Water Pollution Control Program, Anita L. Morse, Edward Zeigler

KWRRI Research Reports

This report is intended to set forth some of the problems and solutions involved in financing and regulating water quality control. The purpose is to record some of the major problems confronting those who legislate water quality, those who espouse technological answers, and those who see the problem in terms of economic solutions. The limits placed by political and institutional constraints on solutions to these problems are frequently not understandable.

Within this report are contained separate investigations: a study of federal-interstate relations and the interstate compact; a study of Kentucky's common law approach to water rights; a study of financing …

Heating The 9th Street Interchange, Louisville, Ky, James H. Havens

Kentucky Transportation Center Research Report

The 9th Street interchange, I 64-2(87)3, was first conceived about 1959. Preliminary design studies began in the early 1960's. Design began about 1964. The idea of heating the ramps was first considered in the early 1960's but was not pursued intently until the final design stage (about 1968). As the design progressed, it became more and more evident that snowing and icing conditions could prevent otherwise normal passage of traffic up and down the ramps. At one point on the structure, a combination of superelevation and grade would produce a 6 1/2 percent slope. The highest ramp or "fly over" …

A Rock Classification Schema, Robert C. Deen, C. D. Tockstein, M. W. Palmer

Kentucky Transportation Center Research Report

The need for engineering data on earth materials for use in site selection, design, construction, and maintenance of major engineering structures is generally accepted. Probably the most pressing need is for such data to use in preliminary considerations of site selection and design alternatives. Maps and(or) surveys giving the areal distribution of earth materials and their characteristics, together with topographic maps available for many areas, would permit much preliminary work on engineering structures to be done without the engineer ever having to leave his office.

Analysis Of Unsteady Flow Toward Artesian Wells By Three-Dimensional Finite Elements, Yang H. Huang, Shen-Jyh Wu

KWRRI Research Reports

A three-dimensional finite element computer program was developed for analyzing unsteady flow toward artesian wells. The program is designed especially for determining the drawdown around an artesian well penetrating fully or partially a nonhomogeneous and anisotropic aquifer of irregular shape and cross section. It can also be used as a general program for aquifer simulation and evaluation. A major advantage of the program lies in the minimum amount of input data required. By assuming the top and bottom boundaries of the aquifer as two arbitrary planes, the aquifer will be divided into six- or eight-node elements, and their nodal coordinates …

High-Intensity Reflective Materials For Signs, Rolands L. Rizenbergs

Kentucky Transportation Center Research Report

Field observations and laboratory tests and evaluations were conducted on High-Intensity and Engineering Grade materials (Scotchlite), manufactured by the Minnesota Mining and Manufacturing Company, and were compared in regard to reflectivity, durability, and cost.

The High-Intensity Grade materials were found to have outstanding performance characteristics in comparison to Engineering Grade materials. The material significantly enhances sign legibility under low-beam illumination, and accelerated weathering tests showed superior durability.

Optimal Highway Safety Improvement Investments By Dynamic Programming [Aug. 1974], Jerry G. Pigman, Kenneth R. Agent, Jesse G. Mayes, Charles V. Zegeer

Kentucky Transportation Center Research Report

The process of determining which projects to implement under a given budget, and which to defer until later, is central to the planning and management of highway systems. With a limited budget for construction, maintenance, and safety improvements, investments which will produce the optimal benefits must be chosen. This is often impossible to accomplish without the aid of a computer because of the complexity of the problem. Dynamic programming has been tested and verified as an efficient method for selecting priority projects to derive maximum benefits.

There are several approaches to priority programming as it is related to the capital …

Dynamic Childbirth Simulator For Teaching Maternity Patient Care, Charles F. Knapp, George S. Eades

Biomedical Engineering Faculty Patents

A programmable patient simulator for teaching maternity patient care includes a life size manikin with a pelvis, vaginal canal, uterus, placenta, umbilical cord, and a fetal doll from which heart sounds are emitted. A programmable electro-pneumatic system controls the simulated uterine contractions, position of the uterus, rupture of membranes, expulsion of fetal doll, and fetal heart rate during labor and delivery sequence. The invention described herein was made in the course of work under a grant or award from the Department of Health, Education and Welfare.

Dynamic Childbirth Simulator For Teaching Maternity Patient Care, Charles F. Knapp, George S. Eades

Biomedical Engineering Faculty Patents

A programmable patient simulator for teaching maternity patient care includes a life size manikin with a pelvis, vaginal canal, uterus, placenta, umbilical cord, and a fetal doll from which heart sounds are emitted. A programmable electro-pneumatic system controls the simulated uterine contractions, position of the uterus, rupture of membranes, expulsion of fetal doll, and fetal heart rate during labor and delivery sequence. The invention described herein was made in the course of work under a grant or award from the Department of Health, Education and Welfare.

Dynamic Childbirth Simulator For Teaching Maternity Patient Care, Charles F. Knapp, George S. Eades

Biomedical Engineering Faculty Patents

A programmable patient simulator for teaching maternity patient care includes a life size manikin with a pelvis, vaginal canal, uterus, placenta, umbilical cord, and a fetal doll from which heart sounds are emitted. A programmable electro-pneumatic system controls the simulated uterine contractions, position of the uterus, rupture of membranes, expulsion of fetal doll, and fetal heart rate during labor and delivery sequence. The invention described herein was made in the course of work under a grant or award from the Department of Health, Education and Welfare.

"Before" Evaluation Of Economic Growth Center Developmental Highway (Ky 55, Campbellsville-Lebanon), Joseph T. Farmer, Jerry G. Pigman

Kentucky Transportation Center Research Report

Before-and-after impact studies were selected as the means of determining the effect of reconstructing a 4.813-mile (7.744-kilometer) section of KY 55 between Campbellsville and Lebanon. The area, though still depressed in terms of per capita income and employment, has many resources available for growth. The study area is predominantly an agriculturally-oriented economy. However, manufacturing employment has increased in recent years, mainly because of industrial sites made available by local industrial commissions.

Overall, social services appear to be adequate and very near statewide averages. Recreational facilities are not highly developed and are primarily of the summer outdoor type.

Reconstruction of KY …

Temperature Distributions In Asphaltic Concrete Pavements, Herbert F. Southgate

Kentucky Transportation Center Research Report

The straight-line relationship between temperatures at a given depth and the surface temperatures combined with 5-day average air temperatures appears to be as valid for upper New York State and Arizona as it was for Maryland. The main differences were in the ranges and mean temperatures. Values given herein are for straight-line equations for all 24 hours and for the depths of 2, 4, 6, 8, 10, and 12 inches (5.1, 10.2, 15.2, 20.3, 25.4, and 30.5 cm). The original concept appears to be valid and may be used with confidence for estimating pavement temperatures at other latitudes and longitudes.

Resonant Footing Test Apparatus, Bobby O. Hardin, Woodrow W. Thurman

Civil Engineering Faculty Patents

An apparatus for conducting resonant footing tests upon undisturbed soils includes an oscillatable mechanical structure with attachable electrical means for causing both oscillation of the structure and measurement of the behavior of the soil under test. The apparatus is transportable to the site at which the test is conducted on soil in-situ, and is adapted to be employed under selective loadings applied downwardly upon the oscillatable structure.

Acoustic Emission Testing Of Shielded Metal-Arc Welds Using Astm A 36 Steel, Theodore Hopwood Ii

Kentucky Transportation Center Research Report

Manual, shielded metal-arc welds on ASTM A 36 structural steel were monitored with acoustic emission equipment. The listening device detected operator inconsistencies and improper electrode deposition during the welding operation. On completion of the weld, acoustic emission monitoring detected slag inclusions, cracking, and martensite formation.

Identification Of Hazardous Locations On Rural Highways In Kentucky, Charles V. Zegeer

Kentucky Transportation Center Research Report

The purpose of this study was to determine the most effective method of identifying hazardous locations for on-site investigations. To decrease the possible effect of random or spurious accidents on the identification of hazardous locations, a 0.3-mile (0.48-km) segment was chosen along with 1- and 2-year periods for accumulating and comparing accident data. An optimal method for identifying hazardous locations and sections was determined to be one which (1) maximizes benefits from improvements, (2) identifies locations with critically high accident rates, and (3) identifies potential hazards. A sample of 170 locations was used to compare several location-identification methods. The procedure …

Shear Strength Of Cohesive Soils And Friction Sleeve Resistance, Vincent P. Drnevich, C. Thomas Gorman, Tommy C. Hopkins

Kentucky Transportation Center Research Report

Cone penetrations tests were performed on the silty clays of Kentucky, U.S.A., using a boring rig to push the Dutch, friction sleeve, cone penetrometer. Thin-walled tube samples were taken from nearby boreholes. For the first four sites, unconfined compression tests and unconsolidated-undrained triaxial test were performed on the samples. For the last four sites, consolidated-undrained triaxial tests were performed on the samples. A procedure for estimating in situ shear strength from triaxial test stress paths was developed.

Small rock fragments in these residual soils caused erratic cone resistance at many locations. As a result, the friction sleeve resistance provided the …

Operational Characteristics Of Lane Drops, Don L. Cornette, Robert C. Deen, James H. Havens

Kentucky Transportation Center Research Report

Traffic behavior studies were conducted at seven lane-drop locations, representing three lane-drop classes. These studies consisted of conflict observations (that is, erratic movements and brakelight applications), spot-speed observations, and lane volume counts. Such a study was made before and after each different traffic control device installation in an attempt to determine which device was the most effective in minimizing conflicts at existing lane drops. A study of conflict deviations indicates that no single type of traffic control device studied was significantly effective in reducing erratic movement and brakelight rates at all seven lane-drop locations. Rather, it appears that different traffic …

"Before" Evaluation Of Economic Growth Center Developmental Highway (Us 25e: Corbin-Barbourville), Joseph T. Farmer, Jerry G. Pigman

Kentucky Transportation Center Research Report

Before-and-after impact studies were selected as the means of determining the effect of reconstructing a 4.886 mile (7.862 kilometer) section of US 25E between Corbin and Barbourville. A comprehensive analysis of the "before" statistics revealed the area designated as a potential growth center suffered from social and economic mediocrity. Many characteristics considered essential for economic prosperity are lacking. Per capita income and educational achievement levels are lower than statewide averages. Transportation is dependent upon highways and many existing routes provide a very low level of service.

On the other hand, the area has adequate industrial and recreational potential to insure …