Digital Commons Network^™

Investigation Of Corrosion Resistance Of Fly Ash Self-Compacting Mortar, Md Marghoobul Haque, Supratic Gupta

International Conference on Durability of Concrete Structures

One of the leading reasons for failure of structural members is corrosion of reinforcement. Structures corresponding to the marine environment like ports, harbours and bridges are more susceptible towards the risk of corrosion. Chlorides are one of the main reasons for the initiation of corrosion which can penetrate from various sources like the marine atmospheric environment or the use of deicing salts in the colder regions. Corrosion is a long-term process, so, in this research, an accelerated corrosion testing of self-compacting mortar has been performed to understand the behaviour of addition of fly ash in the mortar mixes against the …

3d Rbsm Conduit Model For Simulating Moisture Transport In Compressively Damaged Concrete, Dawei Ren, Kohei Nagai

International Conference on Durability of Concrete Structures

This study investigates the simulation of moisture transport in concrete under compressive damage using the 3D RBSM Conduit model. The model combines stress-strain responses from concrete compression experiments with detailed crack data, providing a realistic representation of crack development under varying load conditions. By implementing both unlubricated and lubricated compression tests, different failure modes were observed, influencing penetration patterns. Simulations show that the distribution of cracks significantly accelerates moisture penetration within the concrete. Notably, uniformly distributed cracks, typical of lubricated tests, facilitate deeper and faster moisture transport compared to more localized cracks observed in unlubricated tests. This study validates the …

Public Perceptions Of Universities As Public Entities During The Covid-19 Pandemic Era, Jinho Jung, Laura Barrett, Nicole Olynk Widmar, Mario Ortez

Department of Agricultural Economics Faculty Publications

Higher education institutions are facing challenges in navigating social, cultural, and political issues. The online presence of higher education presents a new set of opportunities and challenges; knowledge, news, and continuing education are increasingly disseminated online. Additionally, the public, student bodies and stakeholders are increasingly looking at reviews or seeking opinions via online and social media to form opinions on institutions. This analysis uses online and social media to analyze and compare perceptions of two public universities in Indiana, namely Purdue University and Indiana University. These two Indiana institutions are located in the same state, allowing for comparisons of public …

Paws And Effect: Canine Companionship And Outcomes In The Chronic Health Condition Hypermobile Ehlers-Danlos Syndrome, Kimberley C. Schenke, Joanna Foster, Danielle Stephens-Lewis

People and Animals: The International Journal of Research and Practice

Emerging research suggests canine companions may support the management of health conditions, yet evidence within complex, long-term conditions like hypermobile Ehlers-Danlos Syndrome (hEDS) remains limited. hEDS is a multifaceted condition often associated with social withdrawal. Thus, the current research provided a high-powered investigation into whether the nonjudgmental support of canine companions could improve health and well-being outcomes for individuals with hEDS. An online survey of 401 participants was utilized to compare differences in health and well-being among individuals with hEDS who have a canine companion to those who do not. Results revealed that participants with canine companions experienced fewer difficulties …

Using Fluid Absorption Modeling To Determine The Intrinsic Permeability Of Cement-Based Materials, Luiz Antonio De Siqueira Neto, O. Burkan Isgor, W. Jason Weiss

C3 Symposium 2025

Neutron radiography (NR) is used during unidirectional fluid absorption experiments to obtain moisture profiles through the height of mortar specimens. The moisture profiles are compared to the results of an established fluid absorption modeling technique, and linear interpolation is used to accurately determine the intrinsic permeability (Kl) of all samples.

Improvement Of Lithium-Metal Electrode All-Solid-State Batteries Performance By Shot Peening And Magnetron Sputtering, Atsuro Okumura, Manabu Kodama

15th International Conference on Shot Peening

To enable fast charging in lithium-metal anode all-solid-state batteries, suppressing lithium dendrite formation at the solid electrolyte (SE) interface is critical. Increasing fracture toughness via shot peening (SP) and improving interfacial contact with Au sputtering can inhibit dendrite growth. However, conventional sputtering may reduce toughness due to localized thermal damage. This study investigated magnetron sputtering as a low-damage, plasma-based Au deposition method. SEs with and without SP were fabricated and coated via normal and magnetron sputtering. Critical current density (CCD) and fracture toughness were evaluated. Without SP, CCD improvement was limited regardless of sputtering method due to poor bonding. With …

Investigation Of Topography Changes Of Blasted Surfaces: An Experimental Perspective Using Fiducial Markers, Stefanie Stoeckel, Sophie Groeger

15th International Conference on Shot Peening

Abrasive blasting is a process that intentionally modifies surface topography to meet specific functional requirements. The blast media is accelerated and interacts directly with the surface through impact. It is evident that the number of impacts and the overlap increase with time. This study aims to investigate these alterations to surface topography through repeated examinations of the same location. A methodology has been developed that employs the use of fiducial markers, which are protected during blasting by a custom 3D-printed cover. This method was used to observe changes in the topography of smooth and rough initial surfaces that had been …

Anisotropic Residual Stress Measurements In Additively Manufactured 316 Stainless Steel Parts, Rajeshree Varma, Donovan Stumpf, Paul R. Mort

15th International Conference on Shot Peening

Additive manufacturing (AM) using laser powder bed fusion (L-PBF) is increasingly used to produce complex parts for industries like aerospace and medical devices. The intrinsic characteristics of AM – layer-wise deposition and rapid thermal cycling – generate significant, anisotropic, residual stresses that can compromise part quality and performance. Recent studies highlight how these stresses are strongly influenced by process parameters and build orientation. X-ray diffraction (XRD) techniques, including sin²ψ and advanced two-dimensional approaches, have become the preferred methods for non-destructive, directionally resolved measurement of residual stress in AM metals. This review surveys advancements in XRD residual stress methods with a …

From Strain To Stress: Stress Map Testing Of Almen Strips, Donovan Stumpf, Rajeshree Varma, Paul R. Mort

15th International Conference on Shot Peening

Almen strips have long been used to evaluate shot peening intensity, with arc height serving as a proxy for compressive residual stress. Stress mapping tests (SMT) in this work involve the controlled flattening of an Almen test strip onto a spatial pressure sensor, acting as an inferential measurement for the net bending moment caused by the relaxation of the peened strip. This work explores how stress mapping tests add insight into the stress state of Almen strips, potentially offering a fast and practical alternative to residual stress depth profiling. SMT data analysis provides a framework for relating Almen gauge height …

Fourier Analyses Of Optical Profilometry As An Inferential Measurement For Impact Coverage., Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

A critical consideration in peening process design is achieving sufficient impact coverage. Conventional methods for assessing coverage rely on manual inspection, which is time-consuming and poorly suited for automated control. In this work, we investigate the use of frequency-domain analysis to quantify surface modification in peened samples using optical profilometry (OP) data. Three-dimensional surface maps of Almen strips were acquired using a high-resolution OP system and analyzed via fast Fourier transform (FFT) to compute spatial power spectral densities (PSDs). PSD maps and radially averaged profiles reveal consistent amplification of harmonic components similar to the nominal particle size, with increasing intensity …

Enhancing High Cycle Fatigue Perfomance Of Electron Beam Melted Ti6al4v: A Study On Shot Peening And Hot Isostatic Pressing, Naghmeh M. Mojib, Dwayne D. Arola, Ramulu Mamidala

15th International Conference on Shot Peening

The qualification of electron beam powder bed fusion (PBF-EB) for safety-critical applications is hindered by variability in high cycle fatigue performance, largely due to surface roughness and internal defects. While Hot Isostatic Pressing (HIP) effectively reduces internal porosity, it does not address surface-initiated fatigue failures. This study investigated the combined effects of HIP and shot peening on enhancing the fatigue performance of PBF-EB Ti6Al4V. Over 50 specimens, including both vertical and horizontal build orientations, underwent high cycle fatigue testing per ASTM E466. X-Ray computed tomography confirmed decrease in defect distribution following HIP, while shot peening resulted in a more uniform …

Influence On Shot Peening And Blast Polishing For Rotating Bending Fatigue Strength Of Vacuum Carburized Steel With Circumferential Notch, Yuji Kobayashi, Hayato Taniguchi, Kiyotaka Masaki

15th International Conference on Shot Peening

In order to improve fuel efficiency in automobiles, weight reduction is necessary as well as improving engine efficiency. For transmission gears, thickness reduction is necessary for weight reduction. When the thickness is reduced, the cross-sectional area becomes smaller, and the load stress increases. Therefore, higher fatigue strength is required. Most gears carry out carburizing. Shot peening is often used to improve the fatigue strength of carburized heat-treated parts. After shot peening, compressive residual stress is introduced, but at the same time, surface roughness is increased. Therefore, the processing conditions of shot peening are very important. Blast polishing is a processing …

Reduced Order Approach For Peening Stress Field Variability, Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

A common goal in shot peening research is to connect operational parameters to resultant residual stress fields, providing a means to control and optimize the effectiveness of surface treatment. In practice, experimental measurements of residual stresses are often averaged values over regions that are large in comparison to an impact dimple. In fact, the stochastic nature of impact locations leads to residual stress fields that are distributed. Finite element peening simulations confirm this observation. The goal of this report is to connect operational parameters to localized fluctuations in residual stress through probabilistic reasoning (Figure 1). In particular, the development of …

Adaptation Of Shot Peen Parameters For Gear Geometry, David J. Breuer, Beth Matlock

15th International Conference on Shot Peening

Shot peening is a well established process for the surface enhancement of gearing. Gearing is a primary example of a high cycle fatigue application that can benefit from residual stress enhancement. Designing shot peening parameters to specific gear geometry based on material, heat treatment, and surface finish is a more precise way to achieve better performance outcomes. One of the best tools to assist in the optimal shot peening is x-ray diffraction (XRD) and its ability to measure small differences that can result in significant performance outcomes. XRD residual stress measurements are a direct measurement of elastic strain. The diffraction …

Numerical Assessment Of Shot Peening Contribution To The Fatigue Strength Of Gear Tooth Root, Gurutz Cortabitarte Laucirica, Xuban Telleria, Iñigo Llavori, Ibai Ulacia, Miren Larrañaga, Jon Ander Esnaola

15th International Conference on Shot Peening

Gears are commonly treated with shot peening (SP) and/or case hardening to enhance fatigue resistance. However, their effects are often conservatively assessed using standardized methods, which can limit their optimal application in industrial components. Particularly, the effect of SP over case-hardened gears remains insufficiently explored. Therefore, the present study evaluates the contribution of SP on single tooth bending fatigue (STBF) strength of raw and case-hardened spur gears, commonly used in automotive and heavy machinery industries. In the study four conditions are addressed: (i) untreated, (ii) case-hardened, (iii) shot-peened, and (iv) case-hardened and shot-peened. First, the residual stress field of the …

The Effect Of Surface Treatment On The Fatigue Strength Of Sus316l Additive Manufactured Products, Hitoshi Nishijima, Yuji Kobayashi, Toshiya Tsuji, Kiyotaka Masaki

15th International Conference on Shot Peening

Rotating bending fatigue tests were conducted to investigate the effect of shot peening and barrel finishing on fatigue properties of SUS316L made by laser PBF which was one of additive manufacturing processes. Surface roughness, residual stress, and fatigue strength were investigated for each specimen. As a result, the fatigue strength of the barrel finished specimens was almost same or better than that of the shot peened specimens. Barrel finished specimens increased 4.1 times higher fatigue strength than as-built specimens. The surface roughness of the specimens after barrel finishing was reduced by up to 96% compared to the as-built specimens. On …

Enhancing The Fatigue Strength Of Am Materials Via Mechanical Surface Treatment, Fabian Keil, Jan Schubnell, Sascha Fliegener, Alexander Heiss

15th International Conference on Shot Peening

Additive manufacturing (AM) processes, while enabling the production of intricate geometries, frequently result in suboptimal surface quality, which can significantly restrict the fatigue strength of components when compared to those manufactured using traditional methods. This study explores the effectiveness of mechanical surface treatment (MST) techniques, specifically shot peening and deep rolling, in enhancing the fatigue performance of additively manufactured AlSi10Mg and 316L alloys. A combination of experimental investigations and finite element simulations was employed to evaluate the influence of these treatments on surface integrity, microstructure, and fatigue life. The results reveal that both MST approaches lead to substantial improvements in …

Dynamic Flowsheet Modeling Of Shot Peening Processes, Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

Process flowsheet modeling is used to map and predict performance by integrating sub-models within a system. This paper presents a dynamic flowsheet for shot peening used to track the effects of media characteristics, removal of worn media, and replenishment thereof. Input parameters include media characteristics, media feed rate, velocity (i.e., air pressure), effective impact area (i.e., nozzle setup), and recharge replenishment. The media working mix is described dynamically using tri-modal size and shape characteristics: as-manufactured, conditioned, and worn modes, each having impact-dependent rate coefficients for transition to the next mode, i.e., as-manufactured > conditioned > worn > debris. The flowsheet includes the effect …

Evaluation Of Peening Intensity With Nozzle-Mounted Sensor During Processing, Akinori Matsui, Shuji Hayashida, Yuji Kobayashi

15th International Conference on Shot Peening

In recent years, digital technologies have been increasingly applied in manufacturing, including visualization and anomaly detection in production equipment. In shot peening, Peening Intensity is a key process control indicator, but its measurement requires significant manual effort. This study aims to evaluate the possibility of using an AE-sensor-mounted nozzle to estimate Peening Intensity. We conducted experiments comparing sensor outputs with experimented Intensity under controlled conditions. A strong correlation (R² ≥ 0.95) was observed, suggesting that Peening Intensity can be estimated via AE sensing. This approach may contribute to labor-saving and automation in shot peening processes.

Evaluating The Effectiveness Of Localized Masking To Prevent Changes In Residual Stress When Shot Peening, James R. Harrison, James Pineault, Tom Mills

15th International Conference on Shot Peening

When shot peening components, it is common practice to mask certain localized regions where peening roughness is not desirable. For example, surfaces that have been highly machined such as bearing races or areas of interference-fit may require masking to protect them from the cold working effects of shot peening. Oftentimes shot peening the grip sections of fatigue test coupons can prevent cracking and failures due to fretting fatigue in the grip area but could affect the outcome of the test if applied to the gauge section of the coupons. Thus, maintaining an “as machined” surface roughness is the most common …

The Use Of A Dynamic Imaging System To Characterize Particle Size And Shape For Shot Peening Media, Matthew Spink, Tod Canty, Langdon Feltner, Paul Mort

15th International Conference on Shot Peening

Shot peening is a cold working process that enhances the mechanical properties of components such as springs, axles, and gears. Shot media are projected at a high velocity against the material’s surface, creating a layer of compressive residual stress that improves fatigue and wear resistance of the material. The size and shape of the media affect the residual stress layer that is created. To ensure consistent quality, it is critical to characterize and control the particle size and shape distribution of the shot media, both as-manufactured and in the working mix. This paper presents how the use of a dynamic …

Methodologies And Applications Of Precision Shot Peening To Hole Or Slot Geometry, James C. Hoffman

15th International Conference on Shot Peening

Shot peening, a commonly used method of fatigue and surface enhancement, is a critical process in many of the components in the aerospace industry. When it comes to small holes and/or slot geometries in these components, the process can become a challenge when these features are smaller than a conventional size Almen strip. In these cases, a decision must be made about how to process this type of geometry. Oftentimes, the method to apply the shot peen process is already defined in a process specification or part print so we must adhere to that method. If a method is not …

Portable Inspection Technology For Shot Peening As Preventive Maintenance At Steel Bridges, Yoshihiro Watanabe, Ryosuke Watanabe, Mitsuru Handa, Kanehisa Hattori, Masato Yamawaki, Koji Kinoshita

15th International Conference on Shot Peening

Positron annihilation lifetime spectroscopy (PALS) is a non-destructively technique to study open-volume lattice defects such as vacancies or dislocations, which is used for fatigue, aging and shot peening inspection. In this study, we developed a portable PALS apparatus that has the ability for on-site measurement[1,2]. We developed the light-shielding technique which enable us to do on-site measurement. Furthermore, we downsized the apparatus size using Monte Carlo simulation technique. We validated that the developed portable apparatus has the same measurement capabilities as the conventional system[1]. We concluded that the developed portable apparatus is sufficiently able to capture the change caused by …

The E-Strip® As A Tool For Predictive Maintenance To Monitor And Control Shot Peening Processes, Walter A. Beach, Scott Glasier

15th International Conference on Shot Peening

The primary objective of this paper is to demonstrate the E-Strip® is capable of providing real-time feedback to the machine controller for making necessary process adjustments due to external forces, such as machine wear. Adjustments may include regulating air pressure and shot flow within pre-defined tolerances dictated by specification. It is anticipated that this integrated approach will significantly reduce variations in intensity levels observed from part to part and lot to lot.

E-Strip® Peening Intensity Sensor - Linearity, Variability And Connectivity, Sylvain A. Forgues, Brigitte Labelle, Ramzi Ben Moussa, Sebastien Beaugrand, Raphael Sarraillon, Sergio Amaya

15th International Conference on Shot Peening

This paper presents the E-Strip®, a novel electronic sensor developed by Shockform to digitally measure shot peening intensity at the part level. Motivated by the limitations of traditional Almen strips—namely, manual handling, time consumption, and susceptibility to human error—the E-Strip® offers a faster, more reliable, and connected alternative. Extensive testing confirmed the E-Strip® output maintains excellent linearity with Almen intensity across a wide range of media and impact levels (R² > 0.997), and its adjustable sensitivity ensures compatibility from low to high intensities. Variability studies showed the E-Strip® provides similar or better consistency than Almen strips at low intensities, although higher …

Community Survey Report: The Rebuild Survey Conducted In Response To The January 2025 Palisades Fire And Eaton Fire In Los Angeles County, Andrew J. Whelton, Cristiane Ferrarezzi, Lauryn Spearing, Anna Hoover, Mónica Palomo, Caitlin Proctor, Jianxi Su, Joseph Toland

Resilience to Emergencies and Disasters

No abstract provided.

A Time Series Analysis Of Herd Investor Behavior Using Online And Social Media Data, Michael L. Smith, Valerie Kilders, Todd Kuethe, Nicole Olynk Widmar

Department of Agricultural Economics Faculty Publications

We examine the relationship between market performance of leading cryptocurrencies (Bitcoin and Ethereum), meme-stocks (AMC, GameStop), and subjects of corporate boycotts (Bud Light) using weekly market price and volume data along with social media data of weekly mentions (which total 337 million in this dataset) and net sentiment. Using vector autoregression (VAR) time series analysis along with Granger causality testing and structural breaks, we successfully predict trade volume of these various assets using social media data and price data. We also find that closing price data and trade volume are reliable predictors of net sentiment about crypto in online and …

Novel Biomolecule-Infused Gelatin Injectable For Treatment Of Recurrent Laryngeal Nerve Injury, Ananya Tadikonda, Sunjay Anekal, Lena W. Chen, Gabriel Sobczak, Troy Wesson, Carmilya Jackson, Marisa A. Egan, Julie C. Liu, Patrick R. Finnegan, Stacey Halum

School of Chemical Engineering Faculty Publications

Objective

Unilateral vocal fold paralysis (UVFP) due to recurrent laryngeal nerve injury (RLN) is a major cause of voice disorders. We have recently identified three biomolecules (agrin, acetylcholine, and neuregulin) with the potential to promote reinnervation after RLN injury. This study aimed to determine if a gelatin injectable with the reinnervating biomolecules will induce site-specific amplification of neurotrophic factor release and reinnervation after RLN injury in unilateral vocal fold paralysis.

Methods

C57BL/6 mice underwent RLN transection with the following treatment allocations: saline control (N = 16), biomolecule cocktail only (N = 16), and biomolecule-infused gelatin (N = …

A Feasibility Study Into The Usability And Application Of An Unmanned Aerial Vehicle For Aircraft Inspection And Quality Assurance Inspections, Reece P. Bhave

Journal of Aviation Technology and Engineering

The global aviation industry is often characterized as one of the safest modes of transportation in the modern world. With an abundance of quality assurance inspections and checks to determine operations safety, modern-day commercial aircraft that are utilized for passenger and cargo flights are held to a higher safety standard defined by regulatory bodies, such as the Federal Aviation Administration in the United States of America and the European Union Aviation Safety Agency in the European Union. While these quality standards are maintained via a series of inspections, checks, and preventative maintenance procedures, they are limited to only visual or …

Stake-And-Weave Trellising Produces Higher Tomato Yield In High Tunnels Than Does A Double- Or Multiple-Leader Vertical-String Support System, Elizabeth Maynard

Department of Horticulture & Landscape Architecture Faculty Publications

Yield of tomatoes (Solanum lycopersicum) grown in high tunnels in Wanatah, IN, USA, was evaluated using two plant support systems: stake-and-weave or vertical-string. With stake-and-weave, plants were not pruned; stakes were placed every two plants and string was woven horizontally along either side of the plants along the row. With vertical-string, indeterminate cultivars Big Beef and Cherokee Purple were pruned to two stems and each stem was clipped to a vertical string. For the determinate cultivar Mountain Fresh, all branches below the first main stem flower cluster except one were removed and the main stem and major branches …