Digital Commons Network^™

Cascading Of Ever Adaptive Variation Of Lzw Algorithm With Arithmetic Coding Method, Ramesh Vishwanatham, Ketan Tejani

Theses

Two known compression algorithms appropriate for communication are LZW and the Arithmetic Coding method. Both algorithms are adaptive and require no extra communication from the encoder to the decoder. We have considered a variation of LZW algorithm known as Online version which result in better compression. Here we present a scheme to cascade Online LZW with Arithmetic algorithms into an Ever Adaptive data compression algorithm which achieves higher compression ratio and is appropriate for communication.

Experimental Study On Filterability Of Leukocytes, Qi Wang

Theses

The filterability of leukocytes treated with A23187, Cytochalasin B, PAF and FMLP and pumped through 5 µm polycarbonate filters at a constant flow rate was examined. The concentration of the four agents was systematically varied. The filtration pressure was continuously recorded for data analysis. The pressure-time curves generally showed multiphasic components, following a small jump step at the beginning of the filtration process. The pressure rise was initially fast (initial faster increased phase, IP) and then rose more slowly (later slower increased phase, LP). The leukocytes treated with A23187 showed increased IP and higher LP values; those which were treated …

Finite Element Analysis Of Torsional Concentric Composite Shaft Using Isoparametric Circular Element, Yee-Haur Wong

Theses

Finite Element Method is used to analyze the concentric composite material shaft subjected to torsion. Isoparametric circular ring element has been formulated to solve the one-dimensional problem. An intermaterial element at the interface has been developed to accomodate the changing modulus of rigidity.

Solutions of Prandtl's stress functions are used to compute shear stresses and torque in the composite shaft. Results of torque of the composite shaft are established using convergence tests of homogeneous solid and hollow shafts. Good agreement with classical solutions are obtained for homogeneous solid and hollow shafts.

A Torsional Concentric Composite Chart has been developed showing …

Electron Field Emission Through A Very Thin Oxide Layer, Guang Yang

Theses

Field Emission of an emitter covered with a very thin oxide layer is modeled and calculated numerically. The additional barrier due to the oxide layer is included in the tunnelling problem by using the standard WKB method and tunnelling transmission matrix method. The following physical parameters are considered: the oxide barrier height, the oxide conduction band edge electron effective mass, and the oxide dielectric constant. Compared with the Fowler-Nordheim equation, which was derived for a clean metallic emitter, the calculation of this work shows a reduction of the emission current density from an emitter covered with an oxide layer a …

Characterization Of Material Removal In The Course Of Abrasive Waterjet (Awj) Machining, Yu Yang

Theses

The objective of this study is to develop a practical procedure for prediction of the results of abrasive waterjet (AWJ) machining. The first stage of the study involves the development of the technique for prediction of the rate of material removal in the course of abrasive waterjet (AWJ) machining. A new parameter, Exergy Distribution Density (EDD), is introduced and used in order to characterize the cutting conditions. EDD, determined as the kinetic energy of particles delivered to a unit length of the generated surface, is the function of diameters of the sapphire nozzle (Dn) and the focusing tube (Dc), the …

Simulation Study Of Monolithic 8-12 Micron Gaas/Algaas Multiple Quantum Well Infrared Image Sensor, Ye Zhu

Theses

The design of a monolithic 8-12 micron GaAs/AlGaAs multiple quantum well infrared image sensor has been tested by computer simulation using PISCES-IIB and SPICE3B.1 software packages. The device structure is in the form of a monolithic GaAs/AlGaAs multiple quantum well (MQW) photoconductor integrated with a GaAs MESFET readout circuit. The readout MESFET's are located in the top layer of the MQW so that a relatively standard GaAs MESFET design and processing technology can be used. The theoretical feasibility of such a vertically integrated structure and the processing compatibility of GaAs/AlGaAs MQW and GaAs MESFET's were investigated in this work.

Our …

Stabilization/Solidification Of Organic Containing Wastes Using Organophilic Clay And Coal Fly Ash, Edith Lagoutte

Theses

The relative merits of eight different coal fly ashes for use in the stabilization/Solidification of a waste containing both heavy metals and pentachlorophenol were investigated. Also studied, was the possible use of either untreated or treated (with hexade-cyl ammonium bromide) clay to enhance the stabilization of the organic. The sample composition was : 62% foundry baghouse dust (or 60% if 2% clay as added to the sample), 4.5% cement, 14% coal fly ash, 19.5% water. Pentachlorophenol was chosen as represen¬tative of the organic contamination. All tests were performed after curing the samples at 22°C, 98% Rh for 28 days. The …

Biodegradation Of Hexachlorocyclohexane In Sand And Wastewater Using Immobilized Phanerochaete Chrysosporum, Ajaykumar C. Gami

Theses

The present study was carried out in order to assess the ability of Phanerochaete chysosporium to degrade lindane (hexachlorocyclohexane) in sand as well as in water. It was found that the fungus is immobilized on saw dust, it is able to degrade lindane in a packed-bed reactor configuration, with a first-order rate constant of 0.00066min^-1. The fungus is also able to degrade lindane in sand. As with the packed-bed reactor, a supplemental carbon source (glucose) is required. In this study it was found that a glucose concentration of 20 gm/kg of sand, and 40% w/w moisture content, give …

Preparation And Testing Of Novel Blocked Isocyanate Dental Adhesives Based Upon Hydroxyhexylmethacrylate, Yunwen Ye

Theses

A new kind of dental adhesive, O-Chlorophenol-TDI-HEMA-Pentaerythritol (TDI), was studied under long term conditions. The test was done in human third molar teeth which had been extracted 7 days to 6 months. Both citric acid and non citric acid pre-treatments were used on dentin surfaces. Based on Causton's[9] mineralizing solution pre-treatment method, we have used 3 kinds of mineralizing solutions, ITS, 0.5% CaCl2, NaF, as pre-treatment solutions. There were no significant differences between the citric acid and non citric acid pre-treatment. The ITS mineralizing solution pre-treatment caused a large increase in bond strength. The average bond strength of 1791 psi …

Manufacturing Automation Protocol Implementation Guide, Richard H. Infantino

Theses

The purpose of this thesis is to provide a starting point for individuals seeking information on the Manufacturing Automation Protocol (MAP) Specification. This thesis is designed to be as comprehensive as possible, yet, still basic enough to be understood by an individual who may not be familiar with computers and networks, and how they function. The intent is to progress gradually from basic networking concepts and characteristics, to defining network requirements, and finally to network design and installation. At the conclusion of the paper is an Organized Method Approach to MAP network design and installation that could serve as a …

Analysis Of Field Distribution Of A Dielectric Resonator And Its Applications, Manohar R. Kamath

Theses

Dielectric resonators (DR) are suitably shaped objects made of high dielectric constant materials like TiO₂, BaO, ZnO, and accessory ingredients, which can function as electrical resonators covering a very wide frequency range upto 40GHz. The physical dimensions of dielectric resonators are in mm range. High dielectric constant material resonators seem to be ideally suited for microwave applications because of their miniature size, low loss, insensitivity to magnetic dc biasing fields, and ability to concentrate large RF magnetic fields in small volumes. However temperature stabilization of dielectric resonators is an important consideration as the center frequency is a function …

Performance Evaluation Of Extended Token Ring Network Under Message Priorities, Prakash B. Kukadia

Theses

Local Area Networks carrying multiple priority classes of messages have received considerable attention recently. A simulation model of a symmetric, priority based network, consisting of token ring networks interconnected by a bridge is implemented. Messages are divided into two priority classes, namely, high priority classes and low priority classes. Two different approaches are considered for transmission of high priority messages. [1] Each station transmits the same amount of high priority traffic when the token reaches the station, regardless of the time elapsed from previous token arrival. [2] The amount of high priority traffic transmitted by each station may vary at …

Temperature Scale-Up On Rotating Biological Contactor Nitrification System, Kuanchun Lee

Theses

The relationship between RBC scale-up factor (SUF) and wastewater temperature is successfully developed by using Dr. Wu's mathematical model as a basis and 114 sets of data from the operation of 8 full-scale and 5 pilot-scale RBC plants served for NH3-N removal. The SUF obtained from this study is put into practice to present the scale-up of hydraulic loading for basic full-scale RBC plant design when the pilot study results are known and the design efficiency is fixed. An additional study is made to investigate two different RBC products manufactured by Autotrol Inc. and Lyco Inc. in terms of the …

Study And Characterization Of Ingaas Photodiode And Photodiode Arrays, Krishna R. Linga

Theses

This thesis describes the InGaAs p-i-n photodiodes, photodiode arrays and their characterization. A work station was also built for the opto-electrical characterization. The main feature of the In,_zGa_iAs photodiodes with x > 0.53 is its response to higher wavelengths than the standard lattice-matched photodiodes. An In_xGa_1-xAs photodiode with x = 0.88 respond to 2.6 μm wavelength. The application of these photodiodes is forlIber optic communications, spectroscopy and instrumentation. A complete characterization and analysis of the In_0.88Ga_0.12As photodiodes is presented. Dark current analysis, which is a critical parameter in photodiodes, …

Integrated Component-Based Computer Design Modeling System : The Implications Of The Representation Of Control Parameters On The Design Process, Allen D. Jablonski

Theses

The design process is dependent on a clear order of integrating and managing all of the control parameters that impact on a building's design. All component elements of a building must be defined by their: Physical and functional relations; Quantitative and calculable properties; Component and/or system functions. This requires a means of representation to depict a model of a building that can be viewed and interpreted by a variety of interested parties. These parties need different types of representation to address their individual control parameters, as each component instance has specific implications on all of the control parameters.

Representations are …

Adaptive Stack Filtering By Lms And Perceptron Learning, Yu-Chou Huang

Theses

Stack filters are a class of sliding?window nonlinear digital filters that possess the weak superposition property(threshold decomposition) and the ordering property known as the stacking property. They have been demonstrated to be robust in suppressing noise. Two methods are introduced in this thesis to adaptively configure a stack filter. One is by employing the Least Mean Square(LMS) algorithm and the other is based on Perceptron learning.

Experimental results are presented to demonstrate the effectiveness of our methods to noise suppression.

Slotted Aloha Protocol For Packet Transmission Via Satellite Link : Throughput Performance Of Continuous Transmission Packet, Solon Karashialis

Theses

The throughput performance of multi-access schemes for data traffic through a satellite channel is analyzed in this paper. Three general schemes are described: channel reservation schemes, random access schemes, and padket reservation schemes. This thesis considers only the random access schemes. Analysis and comparison between ALOHA and Slotted ALOHA are made, but the main emphasis is on satellite channel throughput. A continuous transmission protocol for Slotted ALOHA is suggested in which each ground earth station repeats the transmission of each packet in a number of random repetition slots. The channel is idle when no ground station (GS) is transmitting on …

An Integrated Circuit X-Ray Sensing Array Based On A Cmos Flip-Flop Cell, Huan-Chung Lee

Theses

A novel X-ray sensor IC has beeli designed which counts individual photons at rates up to 5,000,000 counts per second. A two-dimensional X-ray flip-flop sensor array, consisting of an 30 x 30 matrix of CMOS flip-flop sensors integrated in one chip together with an internal clock generator and access selection circuitry is described. A flip-flop sensing cell contains cross-coupled CMOS devices, one of which is connected to a large-area reverse-biased diode. A large area diode exposed to X-ray flux triggers the flip-flop. By reading out the final stable state of the flip-flop, the absence or presence of an X-ray photon …

The Dewaterability Of Anaerobically-Digested Sludges, Hui-Ching Lee

Theses

Vacuum filtration is the most common method used for sludge dewatering. Filtering or dewatering was operated to reduce the moisture content of the sludge after anaerobic digestion treatment.

The main purpose of this study is to determine the effect of the operating conditions of anaerobic digestion system on specific resistance in sludge filtration. The anaerobic sludges used for the present study were produced from the conventional single stage system and the multiple-stage system. From the experimental results, presently obtained that it is possible to compare the advantage and disadvantage of the two different digestion systems.

In addition, the effectiveness of …

Evaluation Of Rates Constants In An Isothermal Turbular Reactor, Yu-Hsin Lin

Theses

To view upon an incompressible laminar-flow fluid in fully developed in a plug reactor, in which a layer of catalyst coated on the inside surface of this reactor. Two kinds of reaction will occur : one is bulk ( homogeneous ) reaction, i.e., the reaction of reactants themselves; another is a first-order irreversible catalyst ( heterogeneous ) reaction, i.e., the reaction of reactants and catalysis.It is apparent that two reactipn rate constants, Κ_b for the homogeneous reaction and Κ_ω for the heterogeneous reaction, will be caused because of these two reactions

One partial differential equation after working of …

Trends Of Eom, B(A)P, Sulfates, And Nitrates In Air-Borne Particulate Matter In Eleven Proximate Locations In New Jersey During 1988, Sathish Pushpala

Theses

Air-borne particulate matter was collected at eleven proximate locations in New Jersey during the year 1988. Particulate matter was extracted in cyclohexane and acetone to separate non-polar and polar components. Particulate matter was also analyzed for B(a)P, Sulfates and Nitrates.

This report presents the inter-site and intra-site variation of concentrations of pollutants between summer and winter seasons. Levels of B(a)P varied from 0.12 to 0.03 ng/M³ between urban and rural sites. During winter, B(a)P concentrations were 5 times more than summer. Concentrations of Cyc which represent mostly primary pollutants, were found 3 times lower in rural sites. Ace fractions …

A Proposed Model For Comparing The Performance Of Neural Networks And Statistical Approaches In Predicting Project Profits Of An Asphalt Paving Company, Josephine Giaimo

Theses

It is currently assumed that the performance of a model for predicting project profits of an asphalt paving company varies with an unknown number of parameters. An earlier study indicates that the parameters are not well understood (Berry, 1990). A search of the literature suggests that the available models usually are described by those who develop and use them as universally reliable and valid tools for solving complex problem (Allman, 1989; Bumke, 1988; Clark, 1988; Cohen & Howe, 1988; Fillon, 1989; Kling, 1990; Lawrence, Petterson, & Hartzberg, 1990; Marose, 1990; Pollak, 1988; Reynolds, 1988; Sullivan & Reeve, 1988; Thurber, 1988). …

Design And Development Of Ccd Camera For Document Scanner Using Optical Fiber Bundle, Aniruddha P. Joshi

Theses

A CCD camera for the gray scale document line scanner has been designed and developed at Photon Imaging Corp. The scanner consists of a revolutionary optical fiber bundle, CCD camera, and control electronics. The key concept resides in the fiber-optic bundle. At one end it has a linear array of equally spaced light guides. These terminate at the opposite end in a square array with a polished surface for viewing by a camera. The fan-out from linear to square end is not done with attention to ordering, so the bundle may be relatively inexpensive. Reordering is done electronically using an …

Electromagnetic Transients Program Interfacing, Enhancement And Comparison With Spice, Siswa Trihadi

Theses

The Electromagnetic Transients Program (EMTP) is a computer program used to simulate high speed power system transients. The EMTP input data structures and the rules in setting up the input data file are described in this thesis by means of two sample cases i.e an RLC series circuit and a sin le line to ground fault in power system.

The EMTP input data are very detailed an highly-structured column-dependent. To improve the user-friendliness of EMTP by ignoring the difficulty of arranging the column structures, this thesis presents the EM P User Interactive Program. Sample cases using this interactive program are …

A 512 X 512 Random Addressable Variable Resolution Image Sensor, Chakravarthy Yarlagadda

Theses

This thesis presents the design and layout of a 512 x 512-element with 20μm x 20μm pixels image sensor that emulates the properties of the human eye and is useful in high speed processing of visual data for machine vision applications. The imager will be able to operate with random-address selection in variable resolution or with multiple regions of interest to reduce the number of pixels readout. The selection of the pixels is done by x-y addressing the MOS switches which connect the photodiode pixel to the output through the sense lines. The design of column decoder and row decoder …

The Dynamics Of Bicycling : An Analytical And Experimental Investigation To Determine The Principles Of Design, Sylvester Yen

Theses

Bicycles have existed in working order for a century. They are mechanical products whose dynamic characteristics are highly nonlinear. This has to some extent prevented detailed analysis and for the most part design has been made from practical experience. The advent of computers has markedly changed the techniques and procedures used to calculate the performance of a bicycle. Bicycling began long ago, and since the first bicycle was demonstrated, bicyclists, scientists and engineers have designed thousands of different bicycles considering safety, comfort to ride and ease of control. Nonetheless, nobody claims to fully understand bicycling. If the fundamental principles exist, …

Photo-Induced Electrochemical Etching Of Inp Semiconductor In A Thin Film Cell, Bungsu Iskandar

Theses

The Photo-Induced Electrochemical Etching of n-InP wafer in aqueous solution is investigated for both reservoir and capillary systems. A sinusoidal spatial variation of light intensity pattern is directly illuminated and promoting etching on an InP semiconductor wafer. The etching process is time-efficient, and produces highly isotropical and a promising high resolution pattern. It gives a good reproducibility and has less contaminating features. Its features may be explained by a non-linear relationship between the electrolyte concentration and the photo-generated holes density at the interaction surface. An optimal reaction rate is determined by the ratio of the reactivity to ionic diffusion, either …

Rotary Micromotor Design With Ic-Compatible Processing, Hong Yu

Theses

Several microelectromechanical rotary motors have been designed and simulated with varying rotor and stator configurations. All of these micromotors operate with an electrostatic power source and have rotor diameters varying from 0.2 to 0.4 mm. These micromotors develop torques in the range 8 to 50 picoNewtons with rotors of polysilicon with 2 micron film thickness based on the detailed simulations of this thesis using a 3-phase voltage power source. The geometries modelled in this work are side-drive and vertical-drive configurations. These micromotors obtain drive torque from the fringe-field differential at the periphery of the rotor poles.

Unlevitated micromotors (with bearings) …

Modeling A Fuel Rich Premixed Laminar Methane Flame Oh, Ch, Nh, Cn Profiles, Including Prompt No, Md. Hasan Ul Karim

Theses

A detailed reaction mechanism based upon fundamental thermochemical kinetic principles has been developed to describe the concentration profiles of OH, CH, NH, CN, and NO including prompt NO radicals in laminar flow, fuel rich methane flames as well as flames doped with 700 ppm ammonia. A one dimensional laminar flat flame code which incorporated diffusion, and the detailed reaction mechanism was used to predict the radical concentration profiles from the model. These calculated values are compared to experimental data of Dean (1984).

The model consist of two reaction subsets, hydrocarbon oxidation set and an ammonia oxidation set. The reactions most …

Implementation Of Parallel Sorting Algorithms On A Transputer Network, Venkatraman U. Calidas

Theses

Many sorting algorithms, such as the bubble sort and the binary tree selection sort, are n-squared algorithms and take O (n2) time to sort n values. These can be easily parallelized; the resulting sorts are called the odd-even transposition sort and the parallel tree selection sort, respectively. These have O(nlogn) time complexity. The quicksort is an O(nlogn) algorithm and it can parallelized to make it an O(logn) algorithm.

A transputer is a microprocessor which has serial links to transmit and receive data from other transputers. The above algorithms are implemented on a network of transputers and the link connections for …