Digital Commons Network^™

3-D Reconstruction Of Microvasculature From High Voltage Electron Microscopy (Hvem) Data, Pradip Kumar Paul

Theses

This is a new method for histoarchitectural and volumetric analyses of cell compartments of microvasculature with the use of a unique combination of computerized 3-D reconstruction and HVEM thick serial cross sections. The technology is potentially a reliable, simple, accurate and fast method. Pioneering work in this area was started by Todd et al. (Circ Res Vol :53 p 319 ;1983) basically using light microscopy, but supported by conventional ultrathin transmission electron microscopy. These techniques are important in that they promise to resolve controversies in terms of evaluating the occurance of hyperplasia and hypertrophy in small resistance vessels in various …

A Feasible Direction Procedure For General Multiple Objective Optimization, Wen-Tsia Liu

Dissertations

The Feasible Direction Finding Problem (DFP) of Zoutendijk is adapted to create a general Mathematical Programming (MP) algorithm for treating optimization problems with multiple objective functions. Classically such problems are reduced to standard MP form by converting them to single objective function problems by the use of weighting functions. Unfortunately not all practical problems can be so reduced. Consider the problem of maximizing the strength of a structure. Typically there are several, or even many, failure modes. All active failure modes must be included in the optimal search in such a way that resistance to one active mode can not …

Teaching In A Virtual Classroom : Volume 2 Of A Virtual Classroom On Eies : Final Evaluation Report, Computerized Conferencing & Communications Center, Starr Roxanne Hiltz

Computerized Conferencing and Communications Center Reports

A Virtual Classroom is a teaching and learning environment located within a computer-mediated communication system. As a teaching environment, it provides a set of tools, strengths, and limitations which are available to an instructor for delivering course materials and structuring learning experiences. Its characteristics are merely potentials, just as the empty classroom with its chalkboards and desks awaits the efforts and creativity of the instructor and the students to make it "come alive."

This is the second volume of the final research report on experiences with the prototype of a Virtual Classroom system constructed and operated on EIES, the Electronic …

Multaid, A Consultant For Multi-Microprocessor Network Selection, Bernabe Javier Arruza

Theses

A knowledge based system has been developed to enable an architectural designer to select an adequate interconnection network to be utilized in a parallel or distributed processing system. It is implemented using the Knowledge Engineering Environment, K.E.E., package from IntelliCorp.

The user will interact with the system through symbolic representation. From the selected symbols, the knowledge base system will identify the most appropiate network for the given application. The system will display the network topology along with all the information and results of all pertinent calculations corresponding to the given network. The program will also display the rule driven search …

Comparative Adsorption Studies On Clay Soils, Prasanna R. Mysore

Theses

An investigation has been made to study clay as sorbent in the treatment of the hazardous contaminants of potential sludge leachate emanating from industrial landfills.

Experimentally was studied six highly toxic and hazardous chemicals, which include: phenol, aniline, cyclohexanol, cyclohexanone, cresol and monochlorophenol. Vermiculate, Kaolinite, Attacote and Hectorite clays were studied as the sorbent material. Removal of organic pollutants were measured using a total organic carbon analyzer (TOC).

Results indicate that these clays can be used for some treatment of the above mentioned organic compounds. The study shows that removal of organic pollutants by clay depends on several factors, such …

Programming For The Prediction Of Thermodynamic Phenomena, One Kwon Rim

Theses

A Thermodynamic Calculation Program was developed. The program contains the calculation procedure for VAPOR/LIQUID EQUILIBRIUM(Isothermal P-X data and T-X data), HEAT-OF-MIXING(liquid mixture data) and LIQUID/LIQUID EQUILIBRIUM SEPARATION data. The program may optionally use the Knox Molecular(GAM), UNIQUAC, NRTL, Wilson and Redlich-Kister equations, and is prepared to accept any kind of model which will be developed in the future. This program also performs parameter file creation, parameter input, updating of parameters, and is structured to allow implementation of data regression when program is updated. Comparison and analysis of each function were executed using this program. It was revealed that VLE(Vapor-Liquid Equilibrium) …

Thermal Desorption Of Hazardous And Toxic Organic Compounds From Soil Matrices : Dichloromethane, Chloroform, Benzene, Toluene, 1-Chloronaphthalene, 1, 2, 4-Trichlorobenzene, Arun S. Chemburkar

Theses

This research project was undertaken to understand the process of desorption/removal of organic compounds from soil matrices under the influence of temperature and gas purging. The project was divided in two parts :

A. Plug deposition experiments: Columns packed with soil matrices were purged with an inert gas under isothermal conditions. Organic compounds were then introduced as a plug on the front of the column by on-line injection. The rate of passage (due to sequential adsorption/desorption) of the plug through the various soil matrices was measured by a gas chromatograph equipped with a flame ionization detector (FID). The compounds studied …

Engraving By Cnc Milling Machine, Ram Tatiparti Reddy

Theses

A detailed study of NC, CNC and Engraving is presented. Engraving of letters of different sizes is done using the present technology in a CNC milling machine. This thesis also contains the design of a communication interface between Mark Century One Plus controller and different peripherals. Software for Engraving and Communication between the controller and a PC is developed. The generated NC code from software is simulated on the controller and the product is cut.

Development Of A Low Cost Pc Based Robot Vision System, Raghunandan Jadhav

Theses

There has been a continued. interest in utilizing machine vision systems for robot guidance applications. Commercial vision systems can be programmed to give information about the parts in the robot work area and this information can be used by the robot computer to guide the robot. In most applications, however, the vision information cannot be easily integrated with the robot control language. This thesis considers implementation of part identification routines directly into a robot guidance language. This makes all the complicated machine vision algorithms transparent to the user and allows him to treat higher level vision functions as an extension …

Morphological Analysis Of Microvessels Using High Voltage Electron Microscopy (Hvem), Ibm Personal Computer And 3-D Reconstruction Software, Wieslaw Slawomir Krajewski

Theses

The mesenteric arterioles (outer diameter < 100 µ) from a normotensive and a hypertensive dog were perfused in situ, excised, post-fixed and embedded in Spurr medium block. Thick serial cross sections (0.5 µ) of the vessels were obtained from hand formed mesas and placed on Formvar coated slot grids.

The cross sections were subjected to High Voltage Electron Microscopy (HVEM) and five or more electronmicrographs were taken to cover the individual cross sections. The prints of electronmicrographs were linearly enlarged (3X) and made into photomontages of sections. The membrane contours in the montages were traced on transparent overlays, producing polygons which in turn were traced on GTCO digitizing pad. All polygons were labeled, color coded and stored in IBM PC's filing system. The vessels were reconstructed from up to 100 whole cross sections and subjected to cell compartmentalvolume analysis. The reconstructed images can be …

Optimal Design Aspects Of A Unit Treating Hazardous Wastes Via Biodegradation : A Theoretical Approach, Farnaz Saghafi

Theses

The treatment of wastes via biodegradation is a widely utilized technique in most industries today. The kinetics of biodegradation, in most cases, follow either the Monod (non-inhibitory) or Andrews (also known as Haldane, inhibitory) model as indicated by published experimental data. The present study investigates aspects of the optimal design of a unit treating wastes when the biodegradation kinetics are those mentioned above. The criterion of optimality is the minimum volume achieving a desired conversion under given load conditions.

Two alternatives from the point of view of the number of vessels (one and two), and three alternatives from the operational …

Fault Location And Control Optimization Planner (Expert System Approach), Fenil Shah

Theses

FALCON is a rule based expert system designed to control a process being regulated by "intelligent" controllers which would at each time and stage execute a series of diagnostic or decision tests and only then initiate a control action identified by the process engineer. The current implementation includes fault identification, diagnostic and process settings in case of low efficiency and poor quality in the product. This research is a part of large research project in flexible manufacturing.

The system is intended to grow into a complete diagnostic master and take corrective actions with the help of the operational personnel.

FALCON …

Multiple-Screen Panning System, Abdo Fathy Youssef

Theses

There is a need to provide graphics capabilities for the objective of "Group Graphics". This is the ability of a group of humans to work collaboratively on the same diagram. It is the intent of this project to provide some of the fundamental software tools to allow a group of individuals to deal with a "mosaic" form of graphics made up of many separate screens that can be panned and conceptually edited by each individual who is working on portions of the overall document.

Simple tools are provided for the creation of graphics screens as well as saveing and retrieving …

Oxidation Of N,N-Dimethylformamide And N,N-Dimethylacetamide In A Photoreactor, Su-Jen Syu

Theses

Oxidation of N,N-dimethylformamide(DMF) and N,N-dimethylacetamide(DMA) was investigated in a 30 liter semi-batch reactor. Five reaction processes were studied by using UV alone, O₃ alone, O₂/UV, O₂/O₃/UV and H2 O₂/UV respectively. Mathematical models have been developed to interpret the reaction kinetics. Reaction rate constants and mass transfer coefficients were determined by using Rosenbrock Hillclimb optimization algorithm. The experimental data and the predicted results from the models were compared. The kinetic parameters obtained from the previous semi-batch modes were applied to the continuous stirred tank reactor (CSTR) system. Results of this work show …

Closed Loop Machining In Precise Turning, Ching-Song Wei

Theses

Closed loop machining (CLM) is one of the most reliable ways to automate tool setting, part positioning and measurement on CNC machine tool. It not only can assure the quality of the product but also can improve the productivity of the machine. This paper describes the CLM from basic turning concept to application of CLM, including the feature of Mark Century 2000T and the programming methods in precise turning.

The hardware and software requirements for CLM system were presented. The algorithm for CLM programs was developed completely with a series of flow charts. Then, on the base of two projects, …

The Fast Fourier Transform In Assembly Languages Of Microprocessor 68000 And Microcontroller 8052, Hari Kumar Baldawa

Theses

In this report, the 256 point radix-2 FFT algorithm is written in assembly languages of microprocessor 68000( or 68008) and microcontroller 8052( or 8051). The data used can be upto 30 bits, of which the least significant 12 bits are assigned for fractional part.

The FFT code in assembly of 68000 is written for Sinclair's QL-100 personal computer with 68008 CPU. The SuperBASIC programs are used to access and test the performance of FFT code. The average time of execution falls between 0.3 to 0.4 seconds for 256 discrete points.

Again, same FFT algorithm is written in assembly language of …

The Evaluation Of The Ti-Speech System On Pc Computer, Ying Wu

Theses

A PC-TI-SPEECH system has been set up by the author of this thesis on the IBM PC/AT compatible computer. The basic functions of the system are as follows: data acquisition, internal signal synthesization, signal processing and speech recognition. The system is built up by a PC, TI-Speech Hardware kit, MADCAP software package,TI-Speech Tool kit. This thesis covers the setup, evaluation and operations of the complete PC-TI-SPEECH system, development of the system for further applications, and operations of running some evaluation programs generated by doing this thesis.

A Modified Extended Kalman Filter As A Parameter Estimator For Linear Discrete-Time Systems, Bruno Johannes Schnekenburger

Theses

This thesis presents the derivation and implementation of a modified Extended Kalman Filter used for Joint state and parameter estimation of linear discrete-time systems operating in a, stochastic Gaussian environment. A novel derivation for the discrete-time Extended Kalman Filter is also presented. In order to eliminate the main deficiencies of the Extended Kalman Filter, which are divergence and biasedness of its estimates, the filter algorithm has been modified. The primary modifications are due to Ljung, who stated global convergence properties for the modified Extended Kalman Filter, when used as a parameter estimator for linear systems.

Implementation of this filter is …

Approximate Methods For Analysis And Design Of Channel And Tee Shaped Reinforced Concrete Columns Under Axial Compression And Biaxial Bending, Chayan Bhattacharyya

Theses

Combined Bending and Axial Compression for irregular shaped (such as L-shaped, Channel shaped, T-shaped) reinforced concrete short column is a common design problem. Current code provisions and the available design aids do not offer an insight into the determination of strength and ductility of biaxially loaded reinforced concrete columns. The reason is that the information on the behavior of irregular shaped reinforced concrete members under combined biaxial bending and axial load is not well known. They are usually overdesigned and this may cause the structure to be stiffer, which may result in loss ductility when applied to seismic regions. Thus …

Microprocessor Controller For A Multi-Targets System, Shoeineng Lin

Theses

This thesis presents a microprocessor controller for a multi-targets system, which is designed by a direct digital control in the modern computer-aided manufacture system. It is made up of digital control theory, computer hardware configuration and software algorithm. An example is illustrated by IBM PC/XT computer. In this example, the control laws of three simple targets are developed and implemented by C-language. Simultaneously, the computer self-test routines, such as CPU, ROM etc, are developed by intel-8088 assembly language.

Application Of Computer Techniques In Groundwater Contamination Studies, Komratchi Raman

Theses

A study has been undertaken to provide insight into two related aspects of groundwater contamination studies - contaminant transport behavior and its analysis by modeling techniques. The study reviews recent research that explains some of the uncertainties in the transport and fate of chemical contaminants in groundwater. Approaches to modeling techniques and data reduction are developed to illustrate their usefulness in analysing existing groundwater data, and to make predictions on the future water chemical characteristics. Three types of study areas have been chosen for this purpose, each representing a different type of groundwater contamination problem. The first study area has …

Robotization For Assembling Small Parts, Frank J. Valese

Theses

The thrust of this paper is directed toward establishing a roboticized small parts assembly line where none currently exist. Technical and pragmatic requisites were established and reviewed prior to installing the proposed robotic workcell. Although the specific model chosen for discussion is the locksmithing industry, the procedures followed, the design tools utilized, and the methods of job-costing employed apply equally to other small parts industries.

Basic industrywide considerations reviewed for each robotization effort included:

1. Choosing the proper application for robotization
2. Obtaining management support and labor input to insure the success of the project
3. Deciding on the economic and production goals …

Transient Analysis Of Macromolecular Blood-Tissue Exchange In Microvascular Bed, Alex Yefim Bekker

Dissertations

Movement of macromolecules across microvascular walls was studied in the hamster cheek pouch with intravital fluorescence microscopy. A graded series of Fluorescein Isothiocyanate labeled Dextrans(FITC) of 20,000 -70,000 molecular weight were used as representative macromolecular tracers. The time dependent extravasation of FITC-Dextrans was video taped for approximately two and a half hours. Permeation of macromolecules from individual microvessels was quantified by digital video image processing. Histograms of the light intensity distributions for selected fields at various times have been measured and used to construct integral optical density - time profiles of the extravasated fluorochromes for particular leaky sites. An integrated …

A Theoretical Investigation Of The Possibility Of Coexistence Of Three Microbial Populations Competing Purely And Simply In Configurations Of Three Interconnected Chemostats, Shiuan-Wu Chang

Theses

It is known from the literature that out of any number of microbial populations competing purely and simply in an environment which is homogeneous and has time invariant inputs (e.g. in an ideal chemostat) only one population can survive in a steady state under any conditions. However it has been proven possible for two competitors to coexist in two interconnected chemostats, which indicates that spatial heterogeneities may lead to coexistence of pure and simple competitors. The present study investigates whether the spatial heterogeneities created by three interconnected bioreactors may lead to a mixed culture (i.e. coexistence) of three pure and …

Degradation Of Aniline And Nitrobenzene In A Photoreactor, Michael Joseph Sowa

Theses

Degradation of aniline and nitrobenzene in aqueuous solutions was studied. Five reaction processes were utilized, including ultraviolet light, ozone, O₂/UV, O₃/O₂/UV, and H₂O₂/UV. A 30 liter semi-batch gas sparged reactor was used for the development of reaction rate and mass transfer parameters in these systems. The results were used to model a continuous stirred tank reactor (CSTR) for the O₃/O₂/UV case. Reasonable agreement was obtained for steady state exit concentrations between the experimental data and those predicted from the model.

Evaluation Of Word Processing Cost Effectiveness, Nicholas E. Tedesco

Theses

The objective of this thesis is to examine the use of word processing technology to determine if its implementation is a cost effective investment. This will be accomplished by comparing the cost of a typewritten page before and after the implementation or upgrade of word processing equipment. The degree of utilization and the impact of utilization on standard costs will also be examined.

Significant difficulty was encountered attempting to locate and compile statistical information on word processing. Therefore, a questionnaire was developed and distributed to the 100 largest public and 100 largest private companies headquartered in New Jersey, requesting information …

Pontryagin's Maximum Principle, Chirasakdi Varuntanya

Theses

In a detailed presentation of Boltyanskii "elementary" proof of the Pontryagin's Maximum Principle, several gaps have been filled in the original one: The control processes which are considered in this paper are described by a system of ordinary differential equations, hence the uniform approach to O of certain O(ε) is proved. Moreover, a complete proof of a theorem about convex cones in Rn and a theorem from Topology are presented. An example of time optimal control illustrating the principle is also solved.

Computered-Aided Digital Filter Design And Simulatio, Pao-Tsan Chiang

Theses

The simulation is written by C language on AT&T Unix pc 7300 environment, some fundamental mathematics is introduced in the beginning, then digital filter specification method: window, frequency sampling, equiripple are discussed, and Kaiser window method is discussed in details for programming.

There are many problems are met in my simulation, such as F.F.T. aliasing, leakage, Picket fence convolution, correlation, but solutions are proposed.

The result could be output data and graph, GSS_Drivers graph package is utilized, because consideration of operation speed and convenience are emphasized, speed is compromised, but easy to be restructured.

A Dsp Toolkit For The Unix/C Environment Of The Pc 7300 Compute, Suwutchai Jesdanun

Theses

The Digital Signal Processing (DSP) TOOLKIT is a package of programs designed to use the fast Fourier transform (FFT) and display its output responses in graphics form. This tool provides three different window functions and five data modifiers for filter designing and spectrum analysis. Flexible features for modifying the plottings, such as y-axis auto-scaling, xy-axis scaling and center line adjusting of the graphics display, are included.

All programs are written in C programming language for the UNIX System Environment of the UNIX PC 7300 computer. The program structure of DSP TOOLKIT is designed so that modules can be added or …

Post-Cracking And Nonlinear Microcomputer Analysis In Reinforced Concrete Beams, Pedro Ricardo Munoz Arias

Theses

The main objective of this Thesis work is to study a non-linear behavior of reinforced concrete structures using the Finite Element Method and an incremental load strategy.

Bond between steel and concrete is simulated using linkage spring elements. The proposed model has a generalized crack propagation capability and it accounts for nonlinearities due to cracking and material properties.

Load-displacement relationships describing the aggregate interlock along the crack and the dowel action at the level of reinforcement are incorporated into a computer program.

A simply supported reinforced concrete beam is analyzed from zero load until failure. Contributions to the shear capacity …