Digital Commons Network^™

Fusion Welding Of Diboride-Carbide Ceramic Composites, Derek Scott King

Doctoral Dissertations

"Plasma and pulsed plasma arc welding (PAW and PPAW) processes were used to fusion weld ZrB₂ containing 20 vol% ZrC. Varying welding parameters resulted in changes in weld pool shape and size, and the size of ZrB₂ grains within the fusion zone. For PAW processes that resulted in a keyhole fusion zone (full penetration), the arc to workpiece power transfer efficiency was estimated to be 2 grain lengths were observed to decrease between binary PAW FZs (~1 mm in length), and binary PPAW FZs (~0.8 mm in length), and an increasing aspect ratio for ZrB₂ grains in …

Containment Materials For Thin-Strip Casting Of Steel, Abhishek Kumar

Doctoral Dissertations

"The focus of this research was to investigate the corrosion behavior of BN-based and ZrO₂-C refractories by molten steel. These refractories are used as side-dam and core-nozzle in the thin-strip casting of steel. The improvement and development of these refractory components will increase the process efficiency by prolonging the refractory service life.

The first part of this study focused on interaction of BN-ZrO₂-SiC side-dams with steel-inclusion system in a laboratory setup under argon gas environment. It was observed that corrosion of this ceramic was severe in contact with steel compared to slag/inclusion.

The second part of …

Synthesis, Characterization And Application Of Acrylic Colloidal Unimolecular Polymer (Cup), Ameya Manohar Natu

Doctoral Dissertations

"Colloidal Unimolecular Polymer (CUP) particles were prepared by the process of water reduction on amphiphilic acrylic copolymers prepared via free radical polymerization technique. The formation of CUP particles was driven by the polymer-polymer interaction being greater than the polymer-solvent interaction and entropically favored by release of the water. It was demonstrated by Dynamic Light Scattering technique that CUP particles based on copolymers below 13,000 MW were unstable and the particles aggregated to a higher particle size. For the polymers with molecular weight (MW) above 13,000, a good correlation between the theoretical and experimental CUP particle size was observed. The rheology …

Analysis Of Ion Emitting Jet Structures During Ionic Liquid Electrospraying, Shawn W. Miller

Doctoral Dissertations

"The ionic liquid [Bmim][DCA] is a propellant candidate for a standalone electrospray thruster or a dual-mode propulsion system. Characterization of positive polarity ions produced by [Bmim][DCA] capillary emitters with a nominal extraction voltage of 2.0 kV within a quadrupole and time-of-flight mass spectrometers is presented along with the predictions of propulsion performance. Flow rates from 0.05 to 2.18 nL/s are used to investigate the impact variations in the flow parameter have on the electrospray plume. The retarding potential analysis reveals ions emitted from the capillary are formed below the emitter potential of 500 eV. Angular distributions indicate broadening of both …

Printed Circuit Board Power Distribution Network Modeling, Analysis And Design, And, Statistical Crosstalk Analysis For High Speed Digital Links, Ketan Shringarpure

Doctoral Dissertations

"High-speed digital systems are moving to higher data rates and smaller supply voltages as the scale of integration goes smaller. With the smaller bit periods and the smaller operating voltages, the tolerable timing and noise margins are reducing. There are many sources of disturbances contributing to the tolerance margins. These margins have to account for inter symbol interference (ISI), reflections, jitter, noise from power distribution networks (PDN) and crosstalk. An important task during the design phase of the system is to find and mitigate the noise from such sources. This thesis proposes modeling and analysis methodology to resolve some of …

The Relative Effect Of Charge Dimensions On Elastic Vibration Attenuation And Blast-Induced Seismic Energy Concepts, Nathan Thomas Rouse

Doctoral Dissertations

"This dissertation focuses on expanding the blasting industry's current understanding of the effect of charge geometry on blast vibration attenuation. The work includes a multiple regression analysis of a sample population of signature hole blast vibration data. The regression analysis is used to identify the relative effect of the variables that affect blast vibrations at various distances from the charge. The study suggests that the most common vibration models used in the blasting industry do not use all of the statistically significant variables. Therefore, the models neglect to fully describe the relationship between the significant variables and the blast vibration. …

Models Predicting The Performance Of Ic Component Or Pcb Channel During Electromagnetic Interference, Chunchun Sui

Doctoral Dissertations

"This dissertation is composed of three papers, which cover the prediction of the characteristics of jitter due to crosstalk and due to simultaneous switching noise, and covers susceptibility of delay locked loop (DLL) to electromagnetic interference.

In the first paper, an improved tail-fit de-convolution method is proposed for characterizing the impact of deterministic jitter in the presence of random jitter. A Wiener filter de-convolution method is also presented for extracting the characteristics of crosstalk induced jitter from measurements of total jitter made when the crosstalk sources were and were not present. The proposed techniques are shown to work well both …

Inclusion Engineering In Mn-Si De-Oxidized Steel For Thin-Strip Casting, Vivek Thapliyal

Doctoral Dissertations

"The focus of this research was to understand inclusion formation and evolution in Mn-Si de-oxidized steels used in thin-strip casting. Inclusions formation and evolution in ultra-low carbon low-alloyed steels were studied. Inclusion engineering can be used to remove or modify detrimental inclusions, which cause casting issues.

The first part of this study focused on inclusion formation as a result of ferro-alloy addition. De-oxidation reaction in steels are the primary source of the typical oxide inclusion formed in steel. For Mn-Si de-oxidized steels ferro-silicon and ferro-manganese are the two ferro-alloys used for de-oxidation. Inclusion formation and evolution during the early stages …

Iterative Ct Reconstruction From Few Projections For The Nondestructive Post Irradiation Examination Of Nuclear Fuel Assemblies, Muhammad Imran Khan Abir

Doctoral Dissertations

The core components (e.g. fuel assemblies, spacer grids, control rods) of the nuclear reactors encounter harsh environment due to high temperature, physical stress, and a tremendous level of radiation. The integrity of these elements is crucial for safe operation of the nuclear power plants. The Post Irradiation Examination (PIE) can reveal information about the integrity of the elements during normal operations and off‐normal events. Computed tomography (CT) is a tool for evaluating the structural integrity of elements non-destructively. CT requires many projections to be acquired from different view angles after which a mathematical algorithm is adopted for reconstruction. Obtaining many …

Advancements In Uncertainty Quantification With Stochastic Expansions Applied To Supersonic And Hypersonic Flows, Thomas Kelsey West Iv

Doctoral Dissertations

"The primary objective of this study was to develop improved methodologies for efficient and accurate uncertainty quantification with stochastic expansions and apply them to problems in supersonic and hypersonic flows. Methods introduced included approaches for efficient dimension reduction, sensitivity analysis, and sparse approximations. These methods and procedures were demonstrated on multiple stochastic models of hypersonic, planetary entry flows, which included high-fidelity, computational fluid dynamics models of radiative heating on the surface of hypersonic inflatable aerodynamic decelerators during Mars and Titan entry. For these stochastic problems, construction of an accurate surrogate model was achieved with as few as 10% of the …

Investigating New Accident Causation, Risk Assessment, And Mitigation Strategy Selection Tools In The Petroleum Industry, Mohammad A. Alkazimi

Doctoral Dissertations

"The inherent complexity of the processes and the volatile nature of petroleum products compel the petroleum industry to continually seek and develop tools and techniques to identify, evaluate, and mitigate potential risks that can negatively impact their process operations. Additionally, government agencies and nonprofit professional societies guide the petroleum industry with regulatory guidelines, standards, and recommended best practices. The industry and these agencies and societies work to improve operational management, to ensure safe working conditions, and to minimize risk of all kinds, so that if failures occur, damage is contained within tolerable limits (Health and Safety Executives, 2013).

The currently …

Computing And The Electrical Transport Properties Of Coupled Quantum Networks, Casey Andrew Cain

Doctoral Dissertations

In this dissertation a number of investigations were conducted on ballistic quantum networks in the mesoscopic range. In this regime, the wave nature of electron transport under the influence of transverse magnetic fields leads to interesting applications for digital logic and computing circuits. The work specifically looks at characterizing a few main areas that would be of interest to experimentalists who are working in nanostructure devices, and is organized as a series of papers. The first paper analyzes scaling relations and normal mode charge distributions for such circuits in both isolated and open (terminals attached) form. The second paper compares …

Nmr T₁ Studies Of Colloidal Unimolecular Polymer (Cup) Surface Water, Yousef Abobaker Dawib

Doctoral Dissertations

"This dissertation is subdivided into three topics: Experimental study of colloidal unimolecular polymer (CUP) hydration; probing of polymer chain dynamics by ¹³C solid state NMR technique; and the anticorrosive effect of 5-mercapto-1, 3, 4-thiadiazole-2(3H)-thione (MTT) derivatives.

The states of water in colloidal unimolecular polymer system were investigated by low field proton NMR. Bound and free water fractions were determined using spin-lattice relaxation measurements. A model equation was used to analyze the inversion recovery data.

The proton cross polarization and the pulse sequence for total spinning sideband suppression CP-TOSS NMR method were developed to determine the chain mobility of polymers …

Reliability-Based Optimization Design Of Geosynthetic Reinforced Embankment Slopes, Michelle (Mingyan) Deng

Doctoral Dissertations

"This study examines the optimization design of geosynthetic reinforced embankment slopes (GRES) considering both economic benefits and technical safety requirements. In engineering design, cost is always a big concern. To minimize the cost, engineers tend to seek an optimal combination of design parameters among the considered alternatives while ensuring the optimal solution is safe. Reliability-based optimization (RBO) is such a technique that provides engineers the optimal design with the minimum cost while all technical design requirements are satisfied. The research goal of this study is to implement a mathematical formulation algorithm of the RBO technique in GRES design. To achieve …

Shape Based Classification And Functional Forecast Of Traffic Flow Profiles, Wasim Kayani

Doctoral Dissertations

This dissertation proposes a methodology for traffic flow pattern analysis, its validation, and forecasting. The shape of the daily traffic flows are directly related to the commuter’s traffic behavior which merit analysis based on their shape characteristics. As a departure from the traditional approaches, this research proposed a methodology based on shape for traffic flow analysis. Specifically, Granulometric Size Distributions (GSDs) were used to achieve classification of daily traffic flow patterns. A mathematical morphology method was used that allows the clustering of shapes. The proposed methodology leads to discovery of interesting daily traffic phenomena such as five normal daily traffic …

Performance Analysis And Modelling Of Hybrid Photovoltaic-Thermal Solar Panels, Nicole C. Annis

Doctoral Dissertations

A photovoltaic-thermal (PVT) panel was constructed, tested, and modelled using both MATLAB and TRNSYS. During the experimental testing, which took place on the Missouri University of Science and Technology campus in Rolla, Missouri; two identical PVT panels were tested alongside two PV panels to gather an electrical baseline for comparison. Approximately 69 days’ worth of data were of data were collected during the summer of 2014. The PV electrical, PVT electrical, PVT thermal and PVT combined (electrical and thermal) efficiencies were 3.5-5.6%, 3.4-5.4%, 20.9-11.6%, and 24.3-17.0%, respectively.

A MATLAB program was developed using existing equations for one-dimensional, quasi-steady model of …

Combustion And Pollutant Characteristics Of Ic Engines Fueled With Hydrogen And Diesel/Hydrogen Mixtures Using 3d Computations With Detailed Chemical Kinetics, Hassan A. Khairallah

Doctoral Dissertations

In order to develop design guidelines for optimum operations of internal combustion engines fueled with alternative fuels, a comprehensive understanding combustion behavior and the pollutant formation inside the cylinder are needed. The first part of this thesis aimed to numerically study the engine performance and in-cylinder pollutant formation in a spark ignition engine fueled with hydrogen. Advanced simulations were performed using multi- dimensional software AVL FIRE coupled with CHEMKIN. The detailed chemical reactions with 29 steps of hydrogen oxidation with additional nitrogen oxidation reactions were also employed. Formation rates of nitrogen oxides (NOx) within the engine were accurately predicted using …

Accuracy Of Theory For Calculating Electron Impact Ionization Of Molecules, Hari Chaluvadi

Doctoral Dissertations

The study of electron impact single ionization of atoms and molecules has provided valuable information about fundamental collisions. The most detailed information is obtained from triple differential cross sections (TDCS) in which the energy and momentum of all three final state particles are determined. These cross sections are much more difficult for theory since the detailed kinematics of the experiment become important. There are many theoretical approximations for ionization of molecules. One of the successful methods is the molecular 3-body distorted wave (M3DW) approximation. One of the strengths of the DW approximation is that it can be applied for any …

Advanced Control Of Grid-Connected Multilevel Power Electronic Rectifiers, Sangin Lee

Doctoral Dissertations

"Multilevel power electronic converters have been gaining attention due to their ability to supply high amounts of power and to handle high voltage levels. In this dissertation, grid connected AC-DC rectifier application is investigated with different topologies and control scheme.

At first, neutral point clamped (NPC) rectifier is employed to transfer power from the grid to the load. The NPC rectifier has two capacitors in order to build multilevel output voltage. However, it causes voltage unbalancing problem. Therefore, the new method has been proposed to regulate each capacitor voltage at the same voltage level. Experimental results show that it is …

The Radiation Physics, Mitigation Approaches And Design Guidelines Of High-Speed Connectors And Cables Analyzed With Numerical Modeling, Analytical Formulation And Measurements, Jing Li

Doctoral Dissertations

The dissertation is composed of three papers, which cover the radiation and mitigation of high-speed connectors and cables analyzed with full wave simulation, numerical modeling, analytical formulation and measurements.

In the first paper, the radiation from the optical cage connector in the frequency range of 4-28 GHz is analyzed with validated full-wave simulation model and analytical formulas. The radiation from the optical cage connector is suppressed with absorbing materials, and the coupling path in optical link is verified, together with the optical cage and module enclosure.

In the second paper, radiation from antenna-mode current and TL-mode current is briefly reviewed …

Modelling Of Interconnects In 3dic Based On Layered Green Functions, Siming Pan

Doctoral Dissertations

As traditional CMOS scaling pace gradually slows down, three-dimensional (3D) integration offers another dimension of in the ”More-than-Moore” era. In this dissertation, a number of investigations were conducted to better model interconnects in 3D integrated circuit (IC), to evaluate electrical behavior including delay, power consumption, signal integrity (SI), and power integrity (PI) for 3D ICs. Partial Element Equivalent Circuit (PEEC) method with layered Green’s function is studied here, since it consumes less computational resources and provides better physical insight to model the interconnects in 3DIC for high-speed digital circuits. The work is organized as a series of papers. The first …

Application Of Unified Invariants For Cyber Physical Systems In Smart Grids, Tamal Paul

Doctoral Dissertations

Cyber-Physical Systems (CPS) are complex engineered systems which consist of physical components with an underlying cyber network. The three main components of a cyber-physical System are: physical system, networking and communications element and a distributed cyber system. The primary challenge for cyber-physical systems is to understand what happens when various sub-systems, which have been developed in an isolated environment, are integrated. CPS studies need to ensure sub-systems that had been designed in isolation to meet certain specifications, when combined, do not cause the overall system to fail. The crux of cyber-physical research is thus to find a common platform to …

Describing Local Community Acceptance With Discrete Choice Theory For Enhanced Community Engagement, Sisi Que

Doctoral Dissertations

This research sought to facilitate improved community (stakeholder) analysis by providing further insight on the determinants of local community acceptance using discrete choice theory. Specifically, the goals were to: (1) Identify, classify, and verify the important project characteristics and key demographic factors which affect local community acceptance of a mining project; (2) Account for the large number of relevant factors inherent in discrete choice experiments for mining community acceptance evaluation; and (3) Examine discrete choice models to select the most appropriate model for mining community consultation. The research will test the hypotheses that various discrete choice models can describe the …

Small Signal Modeling And Analysis Of Microgrid Systems, Md. Rasheduzzaman

Doctoral Dissertations

This dissertation focuses on small-signal modeling and analysis of inverter based microgrid systems. The proposed microgrid consists of two microsources placed on two different buses. The buses are connected using a distribution feeder with some impedance. The proposed microgrid can operate with the grid support, or without the grid support. When operated without the grid support, the standalone system’s microsources participate in controlling the system voltage and frequency. For a non-inertia source, such as the inverter, the load perturbations play an important role in system dynamics. In paper-I, such complex system was studied.

In the grid-tied mode, the microsources share …

Stability Design Criteria And Volt Var Control For Distribution System With Single Phase Solid State Transformers, Darshit Girishchandra Shah

Doctoral Dissertations

Due to recent advancements in semiconductor technology, power electronic converters for high voltage, high power, and high frequency applications will soon be commercially available. Conventional single phase distribution transformers are replaced by solid state transformers (SST) in a distribution test system to investigate their interactive dynamics. Under certain circumstances, instabilities due to harmonic resonance are observed. A design criterion for solid state transformer during no load conditions has been proposed in order to avoid instability using an impedance-based analysis. Stability assessment is also extended to include the impact of distribution system voltages and system wide impedance analysis. It is shown …

Investigation Of Robust Optimization And Evidence Theory With Stochastic Expansions For Aerospace Applications Under Mixed Uncertainty, Harsheel R. Shah

Doctoral Dissertations

One of the primary objectives of this research is to develop a method to model and propagate mixed (aleatory and epistemic) uncertainty in aerospace simulations using DSTE. In order to avoid excessive computational cost associated with large scale applications and the evaluation of Dempster Shafer structures, stochastic expansions are implemented for efficient UQ. The mixed UQ with DSTE approach was demonstrated on an analytical example and high fidelity computational fluid dynamics (CFD) study of transonic flow over a RAE 2822 airfoil.

Another objective is to devise a DSTE based performance assessment framework through the use of quantification of margins and …

Event Sampled Optimal Adaptive Regulation Of Linear And A Class Of Nonlinear Systems, Avimanyu Sahoo

Doctoral Dissertations

In networked control systems (NCS), wherein a communication network is used to close the feedback loop, the transmission of feedback signals and execution of the controller is currently carried out at periodic sampling instants. Thus, this scheme requires a significant computational power and network bandwidth. In contrast, the event-based aperiodic sampling and control, which is introduced recently, appears to relieve the computational burden and high network resource utilization. Therefore, in this dissertation, a suite of novel event sampled adaptive regulation schemes in both discrete and continuous time domain for uncertain linear and nonlinear systems are designed.

Event sampled Q-learning and …

Energy Management In Electric Vehicles: Development And Validation Of An Optimal Driving Strategy, Warren Santiago Vaz

Doctoral Dissertations

Electric vehicles (EVs) are a promising alternative energy mode of transportation for the future. However, due to the limited range and relatively long charging time, it is important to use the stored battery energy in the most optimal manner possible. Existing research has focused on improvements to the hardware or improvements to the energy management strategy (EMS). However, EV drivers may adopt a driving strategy that causes the EMS to operate the EV hardware in inefficient regimes just to fulfil the driver demand. The present study develops an optimal driving strategy to help an EV driver choose a driving strategy …

Development, Testing, And Analytical Modeling Of Fiber-Reinforced Polymer Bridge Deck Panels, Hesham R. Tuwair

Doctoral Dissertations

A fiber-reinforced, polyurethane foam core was developed, tested, and evaluated as a possible replacement for the costly honeycomb core that is currently used to manufacture fiber-reinforced polymer (FRP) bridge deck panels. Replacing these panels would reduce both initial production costs and construction times while also enhancing structural performance. Experimental, numerical, and analytical investigations were each conducted. Three different polyurethane foam (PU) configurations were used for the inner core during the study’s first phase. These configurations consisted of a high-density PU foam (Type 1), a gridwork of thin, interconnecting, glass fiber/resin webs that formed a bidirectional gridwork in-filled with a low-density …

Particle Gel Propagation And Blocking Behavior Through High Permeability Streaks And Fractures, Abdulmohsin Imqam

Doctoral Dissertations

Water channeling, one of the primary reservoir conformance problems, is caused by reservoir heterogeneities that lead to the development of high-permeability streaks and fractures. These streaks and fractures prevent large amounts of oil from being recovered. The ultimate objective of this research was to provide comprehensive insight into designing better particle gel treatments intended for use in large openings, including open fractures, high permeability streaks, and conduits to increase oil recovery and reduce water production.

An intensive laboratory study was conducted to better understand the injection and placement mechanisms of millimeter and micron size preformed particle gels (PPGs) through thief …