Digital Commons Network^™

Performance Investigation Of Surface Modified Ceramic Microfiltration Membranes And The Effects Of Ionic Strength, Choji Bitrus Daches

Masters Theses

"The performance of ceramic membranes surface coated with cysteic acid to improve efficiency and reduce fouling rate was studied under two transmembrane pressure (TMP) and constant crossflow velocity (CFV). The filtration process was done in crossflow mode to allow for extended operation of the membranes. the performance of the membranes were determined in terms of the measured fluxes and on content rejection. Cleaning-in-place (CIP) was done on the membranes to ensure flux recovery after each run. The results showed significant improvement on the performance of the membranes with respect to high permeate fluxes and high oil content rejection (> 99.5%). …

Geophysical Imaging Beneath Lake Chesterfield, Missouri, James Daniell Hayes

Masters Theses

"Lake Chesterfield in Wildwood, Missouri, has been leaking since construction of the earth-fill dam was completed in 1986, despite numerous mitigation efforts. The mitigation efforts, including the injection of grouting and the emplacement of clay liners, has not solve the leakage problem.

In the current study, geophysical (subsurface imaging) data was acquired across the drained and dry lake bed and along the base of the earth-fill dam to 1) map variable depth to top of bedrock, 2) determine the variable quality of the bedrock to depths on the order of 80 ft., 3) identify any significant karst features beneath the …

Practical Methods For Source Separation In Emc Measurements, Yuanzhuo Liu

Masters Theses

"Electromagnetic emission is critical in the electronic industry with the rapid growth of the development of the electronic device. To identify the emission from the multipule sources, two methods are proposed in the near field scan and total radiated power measurement respectively.

The first method can be applied in the measurement of the field generated by multiple non-correlated sources. The contribution of each source is determined using a blind source separation (BSS) technique. The measurements are performed using one scanning probe and stationary reference probes, avoiding the need to measure the spatial correlations of the random field. The resolving result …

Changes In Fresh Properties Of Flowable Concrete Induced By Pumping And Composition Of The Lubrication Layer, Alexis Salinas

Masters Theses

"Pumping is an easy method to move concrete while keeping stability. It is worldwide accepted as one of the principal methods for concrete placement, as it accelerates construction. Typically, concrete acceptance in terms of fresh quantitative empirical properties (i.e. slump/slump flow and air content) are performed prior to the pumping process. However, empirical measurements have the drawback that they only measure 1 point. Rheology is better tool to evaluate the behavior of concrete. Pumping is a process that induces considerable shearing in the concrete that can impact its rheological properties. Therefore, the magnitude of these changes in fresh properties depends …

Review And Data Analysis Of Low Salinity Water Effect Through Induced Fine Migration, Dawei Xu

Masters Theses

"Low salinity water flooding (LSWF) is well proved to be an effective EOR technology both in laboratory and field tests, however, the conditions for LSWF to work and EOR mechanism is still debatable. Up till now, many mechanisms have been proposed to explain the incremental oil recovery in sandstone by LSWF, for instance, fine migration, ionic exchange, wettability alteration and pH increase.

In this study, we only focus on low salinity water flooding effect through induced fine migration mechanism. The objective of this study is to conduct a comprehensive analysis using statistical analysis methods and explaining the mechanism of fine …

Projectile Impact Effects On A 50 Psi Plug Type Coal Mine Seal, Bruce Albert Von Niederhäusern

Masters Theses

"The current lack of projectile damage criteria for mine seals is assessed to determine if criteria should be developed. Impact experiments were performed on a full-scale 50 psi mine seal to determine failure modes, dynamic stress state, and assess risk to existing operational mine seals. Test projectiles were selected from common underground coal mine items propelled by means of a black powder projectile generator. Projectile velocities attained in testing ranged from approximately 100 to 650 ft/s (30 to 200 m/s). Dynamic strain was measured on the non-impact face to derive the state of stress and estimate failure criteria. Penetration models …

Performance Evaluation Of Bmi Resin System For Thin-Ply Composites, Manoj Kumar Reddy Rangapuram

Masters Theses

"Composites materials are increasingly being used in aerospace applications over the past few years. The unique properties like high strength to weight ratio, thermal stability, fatigue and corrosion resistance set them apart from the conventional materials. Composite materials are well suited for the applications where weight is the primary concern in the design. Composites structures are vulnerable to mechanical as well as thermal loadings. Transverse micro-cracking and delamination are the most common type of failures in composite materials. The thickness of the ply being used play a key role dictating the properties of the resultant composite structure. As the ply …

U-Pb Detrital Zircon Geochronology Of Paleozoic Clastics Of The Ozark Plateau: Implication For Sea-Level Fluctuations And Far-Field Tectonics, Chen Zhao

Masters Theses

"The Ozark Plateau of south-central Missouri is underlain by Ordovician to Pennsylvanian carbonate and clastic strata. Enigmatic, presumably Pennsylvanian 'filled sink' structures are common on the Ozark Plateau and remain a source of controversy. We present results for U-Pb ages of detrital zircons for 13 samples from the OP. We use U-Pb ages from other Paleozoic clastics and 'filled sinks' on the OP, to suggest: 1) FSS record a period of Middle Ordovician erosion and sedimentation and 2) document significant shifts in sediment provenance that reflect regional tectonic events affecting the North American Craton.

The KDE plots of normalized detrital …

Aerosol-Jet Printing And Flash Sintering Of Conformal Conductors On Non-Planar Surfaces, I-Meng Chen

Masters Theses

”The printed electronics have been broadly applied in our daily lives, many new manufacturing methodologies are studied and investigated. The research here presented the full manufacturing process of printed conductors of aerosol printing and flash sintering techniques on substrates such as planar and non-planar surfaces.

The aerosol printing (AJP) was introduced because of its simplicity in experimental setup and flexibility of printing. It produces less ink waste and consumes less manufacturing cost. Furthermore, it has the direct-write ability to print in any customized patterns or shapes on non-planar surfaces. In this study, the Cu NPs was selected as the functioning …

Estimating Electromagnetic Emissions From A Site Installation With Multiple Racks Of Server Equipment, Ze Sun

Masters Theses

“There are hundreds, sometimes even thousands, of servers working simultaneously inside a data center. Their radiation can be a problem and cause EMI issues. However, it is not feasible to perform full-wave simulation of these racks because of the large electric size of the model. In this thesis, an algorithm is proposed to predict the emission form rack array. The equivalent dipole source is extracted from EMI measurement data of a single rack and used as the radiation source in the multiple rack model. The coupling between racks cannot be ignored, but through the simulation, it is also found that …

Influence Of Pumping Parameters On The Freeze-Thaw And Scaling Resistance Of Highly Workable Concrete, Alexandra Nicole Wehar

Masters Theses

“Over the past 60 years, pumping concrete has gained popularity due to the economic and technical benefits that typically accompanies it. However, boom configuration and flow rate can adversely affect freeze-thaw and scaling resistance of concrete due to the effects of pressure on the air-void system. Therefore, the objective of this research is to assess the influence of different pumping parameters on the durability of hardened self-consolidating concrete. Self-consolidating, flowable, and conventional concrete mixtures were tested during large scale pumping experiments positioning the pump boom in an “A” and a flat shape as well as using different pumping speeds. In …

Controlled Switching In Kalman Filtering And Iterative Learning Controls, He Li

Masters Theses

“Switching is not an uncommon phenomenon in practical systems and processes, for examples, power switches opening and closing, transmissions lifting from low gear to high gear, and air planes crossing different layers in air. Switching can be a disaster to a system since frequent switching between two asymptotically stable subsystems may result in unstable dynamics. On the contrary, switching can be a benefit to a system since controlled switching is sometimes imposed by the designers to achieve desired performance. This encourages the study of system dynamics and performance when undesired switching occurs or controlled switching is imposed. In this research, …

Hydroxylammonium Nitrate Species In A Monopropellant Electrospray Plume, Mitchell J. Wainwright, Joshua L. Rovey, Shawn W. Miller, Benjamin D. Prince, Steven P. Berg

Mechanical and Aerospace Engineering Faculty Research & Creative Works

A mixture of 1-ethyl-3-methylimidazolium ethyl sulfate ([Emim][EtSO4]) and hydroxylammonium nitrate (HAN) is an energetic monopropellant potentially suitable in a multi-mode chemical-electric microtube-electrospray micro propulsion system. In this work, electrospray plume mass spectra are compared between the monopropellant mixture and neat [Emim][EtSO4]. This comparison clearly indicates new and additional species present in the plume due to the addition of HAN. Mass spectra from 20-600 amu/q were obtained over a variety of angles and flow rates from 2 pL/sec to 3 nL/sec in both cation and anion extraction modes. Mass spectrum dependence on flow rate and angular orientation agree qualitatively well with …

Enhanced Quantum Dots Spontaneous Emission With Metamaterial Perfect Absorbers, Wei Wang, Xiaodong Yang, Ting S. Luk, Jie Gao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Metamaterial perfect absorbers (PAs) made of a hexagonal array of holes on Ag-SiO 2 -Ag thin films have been realized and utilized to enhance the spontaneous emission rate and photoluminescence intensity of CdSe/ZnS quantum dots (QDs) spin-coated on the absorber top surface. Perfect absorption of incoming light occurs at the wavelength where the impedance is matched to that of the free space. When QDs strongly excite both the electric and magnetic resonances at this perfect absorption wavelength, a significant Purcell effect on the spontaneous emission process and enhanced radiative outcoupling of photoluminescence intensity are expected. For perfect absorbers with near-unity …

Column Flotation Performance Prediction: Pca, Ann And Image Analysis-Based Approaches, Fardis Nakhaei, Mehdi Irannajad, Sima Mohammadnejad

Mining Engineering Faculty Research & Creative Works

The flotation froth surface appearance includes remarkable information, which can be employed as a helpful index for the qualitative evaluation of the process efficiency. Image analysis is a practical technology for the sake of achieving process related information that can be employed in expert controllers in order to amend flotation performance. In this paper, the intelligent modelling of relationship between froth characteristics and the metallurgical performance in a pilot column flotation of iron ore was established. Column flotation tests were carried out at a wide range of operating conditions and the froth features along with the metallurgical performances were specified …

Fabrication Of Alcocrfeni High-Entropy Alloy Coating On An Aisi 304 Substrate Via A Cofe₂Ni Intermediate Layer, Wenyuan Cui, Sreekar Karnati, Xinchang Zhang, Elizabeth Burns, Frank W. Liou

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Through laser metal deposition, attempts were made to coat AlCoCrFeNi, a high-entropy alloy (HEA), on an AISI 304 stainless steel substrate to integrate their properties. However, the direct coating of the AlCoCrFeNi HEA on the AISI 304 substrate was found to be unviable due to cracks at the interface between these two materials. The difference in compositional change was suspected to be the source of the cracks. Therefore, a new transition route was performed by coating an intermediate layer of CoFe₂Ni on the AISI 304 substrate. Investigations into the microstructure, phase composition, elemental composition and Vickers hardness were …

Modelling And Evaluation Of Electrical Resonance Eddy Current For Submillimeter Defect Detection, Yew San Hor, Vinod K. Sivaraja, Yu Zhong, Bui V. Phuong, Christopher Lane

Physics Faculty Research & Creative Works

Eddy current (EC) inspection is used extensively in non-destructive testing (NDT) to detect surface-breaking defects of engineering components. However, the sensitivity of conventional eddy current inspection has plateaued in recent years. The ability to detect submillimetre defects before it becomes critical would allow engineering components to remain in-service safely for longer. Typically, it is required that higher frequency EC is employed to achieve a suitable sensitivity for detection of such submillimetre defects. However, that would lead to significant electromagnetic noise affecting the sensitivity of the inspection. To overcome this issue, the electrical-resonance based eddy current method has been proposed, where …

Search For Multimessenger Sources Of Gravitational Waves And High-Energy Neutrinos With Advanced Ligo During Its First Observing Run, Antares, And Icecube, A. Albert, M. André, M. Anghinolfi, Marco Cavaglia, For Full List Of Authors, See Publisher's Website.

Physics Faculty Research & Creative Works

Astrophysical sources of gravitational waves, such as binary neutron star and black hole mergers or core-collapse supernovae, can drive relativistic outflows, giving rise to non-thermal high-energy emission. High-energy neutrinos are signatures of such outflows. The detection of gravitational waves and high-energy neutrinos from common sources could help establish the connection between the dynamics of the progenitor and the properties of the outflow. We searched for associated emission of gravitational waves and high-energy neutrinos from astrophysical transients with minimal assumptions using data from Advanced LIGO from its first observing run O1, and data from the Antares and IceCube neutrino observatories from …

Properties Of The Binary Neutron Star Merger Gw170817, B. P. Abbott, R. Abbott, T. D. Abbott, Marco Cavaglia, For Full List Of Authors, See Publisher's Website.

Physics Faculty Research & Creative Works

On August 17, 2017, the Advanced LIGO and Advanced Virgo gravitational-wave detectors observed a low-mass compact binary inspiral. The initial sky localization of the source of the gravitational-wave signal, GW170817, allowed electromagnetic observatories to identify NGC 4993 as the host galaxy. In this work, we improve initial estimates of the binary's properties, including component masses, spins, and tidal parameters, using the known source location, improved modeling, and recalibrated Virgo data. We extend the range of gravitational-wave frequencies considered down to 23 Hz, compared to 30 Hz in the initial analysis. We also compare results inferred using several signal models, which …

A Compact Single-Element Pattern Reconfigurable Antenna With Wide-Angle Scanning Tuned By A Single Varactor, Haozhan Tian, Lijun Jiang, Tatsuo Itoh

Electrical and Computer Engineering Faculty Research & Creative Works

In this paper, we propose a convenient fixed-frequency beam steering method, using a single patch antenna controlled by only one electronically tunable component. The antenna is based on coupled-mode patch antenna (CMPA) [1] that is capable to scan the beam as the function of frequency. A ground-etched slot loaded with one varactor diode is tuned to be capacitive, resonant, or inductive. In order to test broader tuning range, two kinds of varactors with the ranges of 9.24 pF-1.77 pF and 2.67 pF-0.63 pF are implemented respectively. By analyzing how the loaded slot affects the cavity modes and fields, we demonstrate …

Impulse Measurements Of Electric Solid Propellant In An Electrothermal Ablation-Fed Pulsed Plasma Thruster, Matthew S. Glascock, Joshua L. Rovey, Kurt A. Polzin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electric solid propellants are advanced solid chemical rocket propellants that can be controlled (ignited, throttled and extinguished) through the application and removal of an electric current. These propellants are also being considered for use in the ablative pulsed plasma thruster. In this paper, the performance of an electric solid propellant operating in an electrothermal ablation-fed pulsed plasma thruster was investigated using an inverted pendulum micro-Newton thrust stand. The impulse bit and specific impulse of the device using the electric solid propellant were measured for short-duration test runs of 100 pulses and longer-duration runs to end-of-life, at energy levels of 5, …

Experimental Investigation Of Mixtures Of 1-Ethyl-3-Methylimidazolium Ethyl Sulfate And Ethylammonium Nitrate With Electrospray Propulsion Applications, Mitchell J. Wainwright, Joshua L. Rovey, Shawn W. Miller, Benjamin D. Prince

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Physical properties, performance metrics, and mass spectra of mixtures of two ionic liquids (1-ethyl-3-methylimidazolium ethyl-sulfate aka [Emim][EtSO4] and ethyl ammonium nitrate aka EAN) are investigated from the standpoint of electrospray propulsive characteristics. Spectra suggest that as the [Emim][EtSO4] mixture fraction increases, the intensity of [Emim][EtSO4] related species in the plume also increases, while the presence of EAN decreases. Spectra also show presence of both EAN proton transfer species and species related to chemical reaction of [EtSO4] and water. Despite the volatility of EAN, it emits stably into vacuum at low flow rates when mixed with 25% [Emim][EtSO4]. Spectra also show …

Electric Solid Propellant Ablation In An Arc Discharge, Matthew S. Glascock, Joshua L. Rovey, Kurt A. Polzin

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Electric solid propellants are advanced solid chemical rocket propellants that can be controlled (ignited, throttled, and extinguished) through the application and removal of an electric current. Electric solid propellants are also being considered for pulsed arc ablation electric thrusters, such as the pulsed plasma thruster. The focus of this work is the electrical and ablation characteristics of electric solid propellant within an arc discharge. Arc discharges of 5–20 J per pulse were created within a cylindrical cavity, and results for the electric solid propellant are compared with polytetrafluoroethylene (PTFE), which is a traditional propellant in ablative pulsed plasma thrusters. The …

Real-Time Electrical Impedance Monitoring Of Carbon Fiber-Reinforced Polymer Laminates Undergoing Quasi-Static Indentation, Khaled Almuhammadi, Arief Yudhanto, Gilles Lubineau

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Laminated composites are vulnerable to damage from out-of-plane loading, particularly impact loading, and the incurred damage is often only detected by evaluating the post-impact condition of the composites. Real-time monitoring techniques are desirable for early detection of damage. Utilizing changes in the electrical properties of composites to track incurred damage is promising, but the interpretation of such measurements is still challenging. Here, an electro-mechanical system is introduced to understand how well we could detect mechanical degradation in carbon-fiber-reinforced polymer (CFRP) plates undergoing a quasi-static indentation (QSI) test, which is representative of an impact load. The system measures the in situ, …

An Experimental Approach That Assesses In-Situ Micro-Scale Damage Mechanisms And Fracture Toughness In Thermoplastic Laminates Under Out-Of-Plane Loading, H. Wafai, A. Yudhanto, G. Lubineau, R. Yaldiz, N. Verghese

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Studying the response of laminated composites under out-of-plane loading routinely involves mechanical tests, such as quasi-static indentation or impact. The phenomenology during these tests is so complex that it is difficult to identify different material properties related to each failure mechanism (damage mode). We aim at providing an experimental approach, which is practical and fast, for assessing the in-situ micro-scale damage mechanism and extracting the fracture toughness in thermoplastic laminates under out-of-plane loading. To this end, we developed a dedicated, micro-scale, three-point bending (micro-3PB) test fitted inside a scanning electron microscope (SEM). In a single experiment, we were able: (i) …

The Rollamo 2019, Missouri University Of Science And Technology

Yearbooks

No abstract provided.

Development Of A Switchable Radioisotope Generator, Kyle Mitchell Paaren

Doctoral Dissertations

The Switchable Radioisotope Generator utilizes alpha-induced reactions to produce a combination of photons, neutrons, and protons with varying fluxes dependent on target materials and source geometry. The activity/strength of the secondary radiation is further controlled by manipulating the number of alpha particles that can interact with the target material(s). Analytical equations were solved to confirm secondary radiation production from target materials using average cross sections from TENDL data. TENDL and JENDL data was confirmed by analytically solving for the total alpha-induced cross sections. This information was used to produce the provisional and utility Patent No: US20190013109A1. TENDL data was then …

Atomistic Simulations Of Nanoindentation Response Of Irradiation Defects In Iron, M. Mustafa Azeem, Qingyu Wang, Muhammad Zubair

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Radiation response of a material is a consequence of defects' evolution in any radiation damage event. The radiation-induced defects can significantly alter the mechanical properties of a material. Radiation damage initiates from incident neutron by bombardment on solid material causing production and evolution of Frenkel defects. Since voids are formed due to aggregation of a large number of vacancies that cause dimensional changes and hence irradiation-induced swelling. In order to characterize the effect of irradiation defects, we have performed molecular dynamics (MD) simulations to investigate nanoindentation response of point defects and voids in Fe and their effects on mechanical parameters. …

In Situ Mechanical Characterization Of The Mixed- Mode Fracture Strength Of The Cu/Si Interface For Tsv Structures, Chenglin Wu, Congjie Wei, Yanxiao Li

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In situ nanoindentation experiments have been widely adopted to characterize material behaviors of microelectronic devices. This work introduces the latest developments of nanoindentation experiments in the characterization of nonlinear material properties of 3D integrated microelectronic devices using the through-silicon via (TSV) technique. The elastic, plastic, and interfacial fracture behavior of the copper via and matrix via interface were characterized using small-scale specimens prepared with a focused ion beam (FIB) and nanoindentation experiments. A brittle interfacial fracture was found at the Cu/Si interface under mixed-mode loading with a phase angle ranging from 16.7° to 83.7°. The mixed-mode fracture strengths were extracted …

Smart Building And Construction Materials, Donglu Shi, Julian Wang, Wen Deng

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Advances and innovations in materials science and engineering have always played a substantial role in civil engineering, building structural design, and construction. In recent years, extensive effort has been devoted to the applications of stimuli-responsive smart materials and nanostructures in buildings. These smart materials used in the built environment can be defined as those offering specific functional and adaptable properties in response to thermal, optical, structural, and environmental stimuli. Not only do these materials enhance the overall performance of new building construction but also promise safer structures, longer durability of building elements, efficient building energy savings, greater environmental sustainability, and …