Digital Commons Network^™

Robust Broadband Characterization Of Flexible Absorbers, Sheet Material, And Liquids Using A Coaxial Structure, Joseph Christopher Stecher

Masters Theses

Modern high-frequency measurement systems require reliable calibration and sample positioning to ensure measurement fidelity. This thesis presents three studies addressing practical limitations in broadband material parameter extraction and instrumentation.

The first study introduces a modified Nicolson–Ross–Weir (NRW) technique for flexible, compression-sensitive materials from 100 MHz to 18 GHz. Rigid 3D-printed spacers ensure precise sample positioning, and a T-matrix–based de-embedding procedure removes spacer effects. Validation using microstrip measurements and full-wave simulation confirms accurate permittivity extraction across compression levels.

The second study extends NRW to sheet materials enabling accurate material characterization. Independent validation using toroidal inductors with leakage correction and parallel-plate capacitors …

Validating A Low-Cost Radio Frequency Characterization Framework For Development-Grade Software-Defined Radios In Short-Duration Cubesat Missions, Thomas Wayne Francois

Masters Theses

Software-defined radios (SDRs) and CubeSat platforms have reduced the cost and complexity of space-based communication systems, enabling broader participation in satellite missions. While low-cost radio hardware is increasingly accessible, the ability to characterize and validate its performance remains constrained by the high cost and limited access to traditional RF test equipment. This disparity creates a challenge for small satellite development teams, which must characterize communication-system technical performance with limited access to laboratory-grade instrumentation.

This thesis presents a low-cost RF characterization framework for assessing key radio-frequency performance metrics using readily available hardware and measurement techniques. The approach integrates frequency translation, SDR-based …

Empirical-Based Model Of Spatio-Temporal Errors, Godwin Naaba Ndaa

Masters Theses

This research develops an empirical model to characterize spatial-temporal InSAR errors and improve the accuracy of deformation time-series analysis. Using standardized Sentinel-1 HyP3 products and MintPy, the study quantifies how correlated noise affects velocity precision and validates the results against continuous GNSS velocities.

Residual velocities are near-Gaussian, with σ ~0.92–2.04 cm/yr and ~1 cm/yr on average. Variograms show power-law spatial structure with a non-zero nugget implicating troposphere and decorrelation while errors drop exponentially with more acquisitions; spatial uncertainty is strongly affected by unwrapping errors, coherence, and tropospheric noise, not simply troposphere.

A comparative assessment of on-demand cloud processing with other …

Assessment Of Simulation Software Used For Cubesat Gnc Verification And Validation By University Research Teams, Alexander Taiyo Newett

Masters Theses

As the growth in university satellite teams continues, along with the greater trend in the small satellite market, the need for a guidance, navigation, and control verification and validation pipeline suitable for these young and inexperienced teams becomes evident. Much of the mathematical theory and software implementation of GNC concepts are large hurdles for teams largely composed of undergraduate students.

Many software packages exist that can help these teams achieve GNC verification and validation. If the learning curves of these software packages can be overcome, new satellite teams have the opportunity to better build and test GNC algorithms that are …

Analyzing Sleep Architecture And Brain State Transitions Via Hidden Markov Models On Fmri Data, Brileigh Jay Cates

Masters Theses

Sleep is associated with systematic changes in brain activity and functional connectivity observable in functional magnetic resonance imagining (fMRI) signals. Because subjects often fall asleep during resting-state experiments, the absence of vigilance monitoring can confound the interpretation of resting-state dynamics. Although electroencephalography (EEG) is the gold standard for sleep staging, simultaneous EEG-fMRI acquisition is not always feasible.

This study investigates whether sleep stages can be inferred directly from fMRI using a probabilistic latent-state framework. Hidden Markov Models (HMMs) are applied to blood-oxygen-level-dependent (BOLD) time series to identify latent brain states and their temporal transitions. Inferred states are aligned with EEG-derived …

Public Preferences And Trade-Offs In Critical Mineral Mining Development In The United States, Bamidele Joseph Ajiga

Masters Theses

Rising demand for battery-critical minerals has increased U.S. mining efforts, but projects often face public opposition. There is limited work on how individuals in affected regions evaluate trade-offs between economic and environmental risks.

This research applies a discrete choice experiment to examine individual preferences for proposed battery-critical minerals mining projects in Missouri, Minnesota, and Idaho. 1908 respondents evaluated hypothetical mining projects defined by jobs, state tax revenue, the proportion of tailings reprocessed, groundwater impacts, and surface water impacts, under gold and silver versus battery-critical mineral framings.

Conditional and mixed logit models were used to assess the importance of attributes, demographic …

Autonomous Navigation Development And On-Ground Validation For Satellite Rendezvous And Proximity Operations, Logan Banker

Masters Theses

Spacecraft rendezvous and docking are critical mission phases for various applications of spaceflight, including active debris removal (ADR) and in-orbit servicing, assembly, and manufacturing (ISAM). While previous missions utilized humans to perform rendezvous and docking, this style of mission greatly increases safety risks and cannot be implemented on a large scale. Autonomous servicing satellites provide a path towards scalable rendezvous and proximity operations (RPO) because these autonomous agents do not require human intervention. This work presents a lightweight convolutional neural network (CNN) for the navigation system of an agent which analyzes monocular images and predicts the target's position and orientation …

Assessment And Comparison Of Selected Carbon Ablation Models In Hypersonic Free-Flight And Arc-Jet Conditions, Andrew Steven Heider

Masters Theses

Accurate prediction of ablative thermal protection system (TPS) performance is critical for hypersonic vehicle design. However, numerical prediction of ablation remains challenging because results are influenced by complex physics and the choice of surface chemistry model and assumptions made in material response calculations. The objective of this work is to evaluate several carbon ablation models and their implementation within modern computational fluid dynamics (CFD) codes. Numerical simulations were performed using NASA’s LAURA flow solver and the commercial CFD code ANSYS Fluent, which coupled Navier-Stokes with surface chemistry models describing carbon oxidation, nitridation, and sublimation reactions. Several reaction sets were considered, …

Geometric Effects Of Warfighters On Body Armor Fit And Protective Capabilities Against Shock Wave Energy, Melissa Lynn Sutter

Doctoral Dissertations

Body armor is a vital piece of protective equipment for warfighters to defend against threats, necessitating continued development to improve comfort, weight, and protection. However, female warfighters often wear unisex body armor, designed primarily for the male torso. Current research has evaluated the short- and long-term detriments of female warfighters wearing these armors, focusing on comfort and performance. However, these studies do not comprehensively consider how a non-form-fitting armor compromises warfighter safety from battlefield threats. This research examines the geometric effects of female warfighters on armor protection level when defending against shock threats by evaluating the energy distribution on a …

Assessing The Criticality Of Construction Trades: Skilled Labor Shortages And Their Cost And Schedule Impacts, Tamima Elbashbishy, Islam H. El-Adaway

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Skilled labor shortages are a pressing issue in the construction industry. Existing research has primarily focused on the effects of labor shortages at the project or industry level, but there is limited exploration of how these shortages vary across specific trades and their distinct impacts on project outcomes. Evidence indicates that labor shortages vary significantly among trades. This paper addresses this knowledge gap through quantitatively assessing the criticality of key construction trades based on the (1) extent of skilled labor shortages currently witnessed in each trade, (2) impact of these shortages on cost and schedule performance, and (3) degree of …

Flow Regime-Independent Two-Group Interfacial Area Concentration Model For Dispersed Gas-Liquid Flows In Large-Diameter Pipes, Hossein Barati, Takashi Hibiki, Joshua P. Schlegel, Naofumi Tsukamoto

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

In many power plants, boiling can result in two-phase flows during normal and accident conditions. Heat and mass transfers through the gas-liquid interface in a two-phase flow process are proportional to the interfacial area concentration (IAC). These calculations for nuclear systems are typically performed using advanced system analysis codes such as TRACE. TRACE uses a two-group (2G) model, where bubbles are divided into two groups according to their drag coefficients. Correlations are used to calculate the group-wise void fractions (VFs) and IACs. This study evaluates the accuracy of the TRACE 2G VF and IAC models for vertically upward dispersed flows …

Fairrfl: Fair And Robust Federated Learning In The Presence Of Selfish Clients, Andrea Augello, Ashish Gupta, Giuseppe Lo Re, Sajal K. Das

Computer Science Faculty Research & Creative Works

Federated Learning (FL) is a paradigm that enables collaborative machine learning without disclosing the local data of the participants. However, in real-world FL deployment scenarios, some unscrupolous clients may alter the training process to skew the global model towards their local optimum, unfairly prioritizing their data distribution. Their influence can degrade overall model performance for normal clients and reduce fairness in the system. We call this novel category of misbehaving clients 'selfish'. This work proposes a Fair and Robust strategy for aggregation in the Federated Learning (FL) server to mitigate the effect of Selfish clients (FairRFL). FairRFL incorporates a novel …

Biaxial Bending Response Of Prestressed Concrete Girders Subjected To Accidental Asymmetric Prestressing Strand Loss, Haitham Abdelmalek, Mohanad Abdulazeez, Ahmed Ibrahim, Mohamed Elgawady

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

Bridge prestressed concrete girders are vulnerable to sudden rupture of prestressing strands caused by accidental collisions with over-height trucks. These incidents often result in the asymmetric loss of prestressing strands and concrete sections, generating a biaxial bending moment caused by the combined effects of lateral bending and existing service loads. The induced lateral bending moment reduces the flexural resistance of prestressed concrete (PC) girders. However, the current AASHTO LRFD (load and resistance factor design) provisions for flexural resistance in PC members do not explicitly address the complexities introduced by biaxial bending, leaving the extent of strength reduction uncertain. This paper …

Implementation Of Tritium Transport In A Gas-Liquid Contactor Cfd Simulation Of Tritium Extraction From Lead-Lithium In Ansys Fluent, Anthony G. Bowers, Subash L. Sharma, Thomas F. Fuerst

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

Modifications to the Computational Fluid Dynamic (CFD) software ANSYS Fluent were done to quantify and characterize tritium transport in gas-liquid contactors (GLCs). A double-slit, Ergun-like equation was employed for the porous media model, with Ergun coefficients validated with Sulzer's Sulcol software. Tritium transport from PbLi within the GLC was verified against analytical models. The geometry of the CFD model was based on the MELODIE GLC experiment. The hydrodynamic CFD pressure drop results align well with Sulcol estimations and fall between the predictions of the analytical Delft-Olujić and Billet and Schultes models. In terms of mass transfer efficiency, traditional mass transfer …

Long Short-Term Memory (Lstm) -Based Neural Network Model For Optimizing Composite Manufacturing Process Using Autoclave, Sourav Bolar, Steven Corns, Nayan Pundhir, Kumbla Chandrashekhara

Engineering Management and Systems Engineering Faculty Research & Creative Works

Producing high-quality fiber-reinforced composites requires precise temperature control during autoclave curing, as even small variations can lead to defects that compromise strength and reliability. At the same time, manufacturers aim to reduce energy use and shorten curing cycles without sacrificing material performance. To address these challenges, this study develops a data-driven Long Short-Term Memory (LSTM) neural network model capable of forecasting temperature evolution inside the autoclave throughout the curing cycle. The model is trained on time-series temperature data collected from multiple sensing locations, enabling it to learn the spatial and temporal trends that govern heat flow during curing. Data augmentation …

Synthesis Of Nickel Nanoparticles By Gamma Irradiation And Femtosecond Laser Ablation, V. M. Rao, Y. Han, H. Tsai, C. H.C. Giraldo, T. Akyurek

Nuclear Engineering and Radiation Science Faculty Research & Creative Works

Nickel nanoparticles were synthesized by (i) gamma irradiation of aqueous nickel chloride precursors and (ii) double scan femtosecond laser (FSL) ablation of a pure nickel foil in water. The nanoparticles produced by FSL ablation were further stabilized in acetone. Gamma radiolysis yielded nickel nanoparticles in the 2–22 nm range, with the average particle diameter governed by the total absorbed dose. Nickel nanoparticles produced by double scan FSL ablation were in the 2–17 nm range but less monodispersed than the nanoparticles produced via gamma radiolysis. FSL ablation proved to be superior in terms of yielding a higher number of smaller nanoparticles …

Reflections On Linear B, (Part 15): Sign 81 In Linear A And The Egyptian Four-Headed Ram God, Gerald Leonard Cohen

Arts, Languages and Philosophy Faculty Research & Creative Works

This article makes several tentative suggestions, including:

1. Linear A sign 81 (antecedent of Linear B81) may be an abbreviated image (two heads) of the four-headed Egyptian ram god Banebdjedet, with the horizontal line designating his horns shifted downward to the middle of the character.

2. A few other Linear A characters (e.g., sign 305) may represent slight alterations of sign A81.

3. Linear A82 includes two sets of three short horizontal lines. Those might signify brightness, and in the case of Banebdjedet the brightness would be his wisdom.

Partially Penalized Anisotropic Trilinear Ife-Pic Methods For Dc Plasma Transport Problems, Jiahui Li, Guangqing Xia, Yajie Han, Ziping Wang, Chang Lu, Xiaoming He

Mathematics and Statistics Faculty Research & Creative Works

Implicit and hybrid particle-in-cell methods are widely used for efficient simulation of DC discharge plasma transport. However, their computations require solving anisotropic elliptic equations and face challenges related to mesh geometry, non-axisymmetry, and complex interfaces. Moreover, the accuracy of particle trajectories is critical for plasma etching and erosion studies, where errors near interfaces can significantly impact simulation results. To address these challenges, this paper proposes a three-dimensional anisotropic trilinear partially penalized immersed finite element (ATPPIFE) method, which captures interfaces on Cartesian meshes and effectively reduces discontinuities at interface element faces, ensuring that particle trajectories better align with real-world behavior. Building …

Elevated Temperature Flexure Behavior Of Continuous Carbon Fiber Reinforced Zrb2–Zrsi2 Ultrahigh Temperature Ceramic Matrix Composites, Jacob Stacy, Aaron Ginsparg, Jason Lonergan, Jeremy Watts, Gregory Hilmas

Materials Science and Engineering Faculty Research & Creative Works

Ultrahigh temperature ceramic matrix composites (UHTCMCs) were fabricated from unidirectional prepreg tapes consisting of a matrix of ZrB₂ with 5, 10, and 15 vol.% ZrSi₂ additions and continuous polyacrylonitrile carbon fibers and were densified at 1600°C in a hot press. The relative matrix densities ranged from 88% to 93% with interlayer spacings of ∼72 µm and fiber volume fractions between 30% and 36%. Phenolic resin additions were utilized to react with ZrSi₂ acting as a transient sintering aid to form ZrC and SiC phases. Elastic moduli of the UHTCMCs decreased with increasing temperature during 4-pt flexure testing. …

Quantitative Grain Structure And Texture Analysis Of Hot-Pressed Zrb2 Via 3d Ebsd, Randi Swanson, Michael Chapman, Yue Zhou, Ashley Hilmas, Lisa Rueschhoff, Michael Uchic, William Fahrenholtz, Scott J. Mccormack

Materials Science and Engineering Faculty Research & Creative Works

Understanding and controlling the grain structure of ZrB₂ is critical for optimizing its mechanical and thermal performance in high-temperature applications. Fully dense ZrB₂, densified by hot pressing at 2150˚C and 32 MPa, was analyzed in three dimensions using electron backscattered diffraction, electron and optical microscopy, and mechanical polishing serial sectioning. Grain size followed a gamma distribution, with extreme deviations observed only in the largest 0.1% of grains. Large grains exhibited plate-like morphologies, with the shortest-to-longest axis ratio converging to ∼0.4 as grain volume increased. This work revealed a crystallographically controlled growth mechanism orthogonal to [0001] that is …

The Effects Of Mold Flux Contamination On Oxide Scale Formation And Hydro-Descaling Efficiency During Steel Processing, Tochukwu Princewill Ojiako, Richard Osei, Mario Buchely, Haiming Wen, Simon Lekakh, Ronald O'Malley

Materials Science and Engineering Faculty Research & Creative Works

Oxide scale formation during thin-slab continuous casting has a complex structure, which is influenced by mold flux contamination, that modifies interfacial reactions during solidification, subsequent reheating, and descaling. While individual aspects of the oxidation behavior of carbon steel have been previously examined, the synergetic effects of mold flux contamination during continuous casting and subsequent reheating on scale modification and the efficiency of hydraulic descaling remain inadequately studied. This study quantitatively examines the effect of flux composition on oxide scale evolution, adhesion, and hydraulic removal in low-carbon steel under simulated industrial conditions. Slab samples with as-cast, cleaned, and flux-coated surfaces were …

Simulated Lunar Gravity Testing Of A Magnetic And Electrostatic System For Beneficiating Lunar Regolith, Blake A. Coffman, Gabriel Porter, Lindsay Manteufel, Mitchell Cottrell, Jeffrey D. Smith, David J. Bayless, William Shonberg, Frank D. Han, Fateme Rezaei, Kirby Runyon

Materials Science and Engineering Faculty Research & Creative Works

We present the design and testing of a lunar regolith beneficiation device that utilizes magnetic and electrostatic separation methods to concentrate desired minerals by removing unwanted material, such as the mineral anorthite, from bulk lunar regolith. The beneficiated materials would have value for downstream in-situ resource utilization (ISRU) processes such as metal extraction, oxygen extraction, and metal oxide additive manufacturing processes. The apparatus uses a dual-strength magnet system with N52 and N42 neodymium magnets to separate particles by magnetic susceptibility. The electrostatic separation system, which acts like a sieve, sorts the regolith simulant by particle size using a single-phase 50% …

High Temperature Diffraction From Aerodynamically Levitated Materials, Chris J. Benmore, Stephen K. Wilke, David Lipke, Richard Weber

Materials Science and Engineering Faculty Research & Creative Works

Aerodynamic levitation combined with laser beam heating has become an established technique for studying the structure of materials at ultra-high temperatures and under non-equilibrium conditions. This article briefly highlights some recent technical and scientific advancements in understanding the relationships between a material's behavior and its structure, investigated using diffraction methods. It focuses on three evolving frontiers: sophisticated sample environments for accessing metastable states and reactive chemistries, high-flux photon and neutron probes to reveal atomic structure, and advanced computational modeling frameworks. Free from contamination, containerless processing (levitation) can minimize heterogeneous nucleation at the interface, enabling access to deeply supercooled melts or …

A Combined Stochastic And Physical Framework For Alloys And Metal Casting Processes Modeling, Simon N. Lekakh, Oleg Neroslavsky

Materials Science and Engineering Faculty Research & Creative Works

High temperature metal casting processes have dualistic nature and conceptually consist of two parts of distinct processes: the first type is deterministic, strictly obeying the physical law, while the second type is stochastic. Therefore, the metal casting processes are not precisely predictable, and deterministic considerations cannot provide exact outcomes. To solve this problem, the combined stochastic and deterministic framework was suggested. The local processes were described using deterministic models for several parameter arrangements, while the distribution of these arrangements on macro level was calculated using stochastic approaches. The approach was used for cast alloy design, investment casting process optimization, and …

Thermal Transformations And Mechanical Properties Of All-D-Metal Mn2fecu Heusler-Type Shape Memory Alloy, Choji J. Daches, Joseph W. Newkirk, Mario Buchely

Materials Science and Engineering Faculty Research & Creative Works

All-d-metal Heusler alloys are emerging functional materials in which magnetic ordering, lattice distortion, and mechanical behavior are strongly coupled through d–d electronic interactions. This study systematically investigates the structural, thermal, magnetic, and mechanical properties of Mn₂FeCu synthesized within a Heusler-type compositional framework. SEM/EDS revealed a dual-phase FCC-based microstructure consisting of Mn–Fe–rich and Mn–Cu–rich domains, while XRD confirmed FCC symmetry with compositional partitioning rather than full L2₁ ordering. Differential scanning calorimetry identified partial melting of the Cu-rich phase near ~ 900 °C. Dilatometry showed a thermoelastic FCC → FCT transformation at ~ 770–780 °C with a recoverable strain of ~ 0.067%. …

Comparative Evaluation Of Gating Systems In Femnal Castings, K. Balasubramanian, Laura Bartlett, M. Xu

Materials Science and Engineering Faculty Research & Creative Works

To understand the efficiency of gating systems, four systems, namely AFS styled pressurized system, AFS styled non-pressurized system, naturally pressurized system with a side riser and a naturally pressurized system with a top riser, were studied. The naturally pressurized systems were provided with overflows which collected the incoming metal swirl while the pressurized and non-pressurized systems had runner wells. Parameters like velocity of metal flow, air entrapment, microporosity and Niyama criterion were considered, and a design was developed with a common pouring basin using solidification software. Two molds were 3D printed using carbonitride sand, and steel of composition Fe-29Mn-8.2Al-0.91C-0.88Si-0.49Mo was …

Design Of Novel Gating Systems For Steel Castings, K. Balasubramanian, Laura Bartlett, M. Xu

Materials Science and Engineering Faculty Research & Creative Works

Gating systems play an important role in determining the quality and mechanical properties of castings. To understand the efficiency of gating systems, four systems, namely pressurized system, non-pressurized system, naturally pressurized system with a side riser and a naturally pressurized system with a top riser, were studied. The naturally pressurized systems were provided with overflows which collected the incoming metal swirl. Parameters like velocity of metal flow, air entrapment, microporosity and Niyama criterion were considered, and a design was developed with a common pouring basin. 8630 alloy was poured into two molds using a teapot ladle. The inclusion analysis revealed …

Overcoming Resolution Vs. Throughput Trade-Offs In Ceramic Material Extrusion Additive Manufacturing Via Viscoelastic Filament Stretching, Abid H. Rafi, David W. Lipke, Jeremy L. Watts, Gregory E. Hilmas, Ming C. Leu

Materials Science and Engineering Faculty Research & Creative Works

Fabricating large, monolithic ceramic parts using material-extrusion additive manufacturing remains challenging due to difficulty maintaining uniform moisture content during printing, which can lead to drying-induced defects such as warping and cracking, especially as part size and print time increase. Fabricated parts have trade-offs among print resolution, high throughput, and structural fidelity. Our study has shown that increasing the ratio of nozzle traverse speed vs. material extrusion speed increases filament stretching in viscoelastic ceramic paste, helping to overcome the trade-offs between resolution and throughput. Using aqueous ZrB2–SiC (70/30 vol.%) as a representative ultra-high temperature ceramic paste, rheological characterisation revealed viscoelastic yield-stress …

Microstructure And Properties Of Oxide Dispersion-Strengthened Alloys, Ertugrul Demir, Seung Min Ha, Anish Ranjan, Xingshuo Zhang, Aaron Penders, Mukesh Bachhav, Xiaochun Li, Lin Shao, Alexander Demblon, Haiming Wen, Enrique Lavernia

Materials Science and Engineering Faculty Research & Creative Works

Oxide dispersion-strengthened (ODS) alloys are a critical class of structural materials for extreme environments, owing to their unique combination of high-temperature strength, thermal stability, and radiation tolerance, enabled by a very high density of nanoscale oxide dispersoids. These features make ODS alloys attractive for advanced nuclear systems, aerospace applications, and other harsh-service conditions where conventional alloys rapidly degrade. Despite decades of development, key challenges remain in understanding how nanoscale oxides interact with matrix microstructures, alloy chemistry, and irradiation-induced defects to control macroscopic performance. This review provides a focused, mechanism-based synthesis of the microstructural features that govern the properties of ODS …

Serum Biomarker Trajectory Clusters Predict Functional Outcome And Quality Of Life For Traumatic Brain Injury, Thanh Son Do, Chantal Carnes, Zhihui Yang, Firas Kobeissy, Hamad Yadikar, Gayla R. Olbricht, Olli Tenovuo, Jussi P. Posti, Ewout W. Steyerberg, Lindsay Wilson, Nicole Von Steinbüchel, Endre Czeiter, Andras Buki, David K. Menon

Mathematics and Statistics Faculty Research & Creative Works

Serum brain-enriched biomarkers are increasingly employed in the clinical evaluation of traumatic brain injury (TBI) to assist with triage, neuroimaging decisions, and prognostication. However, the potential of temporal biomarker trajectories to inform disease monitoring and long-term outcomes remains underexplored. We aim to identify distinct biomarker trajectory (TRAJ) profiles in traumatic brain injury patients and to examine their associations with long-term clinical outcomes. The study included 373, CT-positive Intensive Care Unit (ICU) traumatic brain injury patients (256 with initial Glasgow Coma Scale 3–12) from the Collaborative European Neurotrauma Effectiveness Research in TBI (CENTER-TBI) core study who had at least two serum …