Digital Commons Network^™

Optimization Of Flywheel Design For Internal Combustion Engines, Dady Jal Patel

Masters Theses

"A new approach to the problem of flywheel design has been developed, thus eliminating some of the problems of conventional design. The term flywheel design, in this thesis, refers to the determination of the flywheel inertia (mass moment of inertia) only. Two versatile computer programs were set up to obtain the flywheel inertia and the turning moment diagram for a large variety of internal combustion engines, and use was made of these programs to optimize the inertia of the flywheel with respect to speed. As an illustration the data of a 1960 Corvair engine were selected, and the results obtained …

Analysis Of Flat Slabs With Various Edge Supports, Wu-Mo Chern

Masters Theses

"This study presents the solution of flat slabs with various edge conditions including T-Beam edge supports, The equations formulated are based on the finite difference method and solved using an electronic computer.

The results indicate that the solution of these slabs by the finite difference approximation is a practical method. In addition, this method is more flexible and yields moment values that are considerably more accurate than those obtained using the ACI Code"--Abstract, page ii.

An X-Ray Study Of The Lead Zirconate-Bismuth Ferrate System, Pen-Chu Chou

Masters Theses

"The lead zirconate-bismuth ferrate system was studied employing x-ray and microscopic analysis. Samples were prepared by sintering stoichiometric mixtures of the corresponding oxides followed by air quenching. The results of the analyses show the system to be probably solid solutions over the entire compositional range, although small amounts of other phases are present in some regions.

X-ray data indicate a multiple cell, orthorhombic phase, to exist over the range 100-30 mole percent PbZrO₃ . From 100-82 mole percent PbZrO₃ , the addition of BiFeO₃ reduces the distortion of the phase such that a nearly cubic x-ray pattern is obtained at …

The Transmission Of Loads To Point Bearing Piles In Sand Beneath Retaining Walls, Alan Albert Kamp

Masters Theses

"An experimental investigation was made of the way in which loads were transmitted to point bearing H-piles in sand under a retaining wall. Using a plastic model, the moments and axial loads were determined along the length of the pile by measuring the strains with electric strain gages. A comparison was made of the experimental results at the top of the pile and the analytical results at this point; the latter obtained from the common practice used in design. The comparison was very poor because the excessive horizontal load (that part of the horizontal load which could not be carried …

The Dielectric Properties Of A Synthetic Fluor-Mica Formed By Glass-Ceramic Fabrication Techniques, Ray Fred Schumacher

Masters Theses

"A tetrasilicic fluor-mica, K₂Mg₅Si₈O₂₀F₄, was synthesized, utilizing glass forming techniques and subsequent heat treating of the mica glass. Discs, approximately two inches in diameter, were formed and heat-treated at selected temperatures between 700⁰C. and 1150⁰C. for various time periods. Density change, weight loss, shrinkage, and dielectric properties were measured to determine the characteristics of this material"--Abstract, page ii.

Analog Simulation Of A Synchronous Machine, J. Derald Morgan

Masters Theses

"The problem presented here is a study by an analog computer simulation of a synchronous machine under balanced three phase, short-circuit conditions. The purpose is to obtain a solution that is more accurate than one obtained by approximate methods using transient and subtransient reactances as is often done. This simulation is accomplished by using an idealized synchronous machine. The equations relating voltage and currents in the machine, as well as speed and torque, are presented for simulation. The equations for the machine include the saliency of one member, as well as the effect of speed and the damper windings. A …

A Feedback Compensator Design For Linear Control Systems, Thsai-Ten Lin

Masters Theses

"The compensation process in control system engineering is indispensable. The addition of a compensator to a fixed plant can often make the system meet certain specifications easily. In this study an attempt was made to use a general purpose digital computer to design a feedback compensator. The method developed is first to determine the minimum gain of the amplifier and the number of compensator poles and zeros based on the given specifications. then free hand root-loci are plotted, with several combinations of possible compensation variables. These data are used as the open-loop transfer function from which the poles and zeros …

Evaluation Of Pile Bearing Capacity By Use Of The Wave Equation, Stuart H. Williams

Masters Theses

"The wave equation method of evaluating pile bearing capacity is investigated by using data obtained from a comprehensive pile testing program. Modifications which create a more accurate and realistic approach are made to the method proposed by previous investigators. With the use of these modifications, correlation between observed and computed results is more readily obtained. Selected pile formulas in the empirical, static, and dynamic categories are reviewed so that a direct comparison between these and the wave equation method can be made"--Abstract, page ii.

An Evaluation Of The Feasibility Of Neutron Microradiography, Maynard L. Arment

Masters Theses

"The metal working industry has used metallography and microradiography extensively in the past decade. X-ray or gamma microradiography has several advantages as compared to metallography, but a disadvantage concerning alloys of adjacent elements; microradiography cannot distinguish between elements 2 or less atomic numbers apart. Attempts were made using neutron microradiography to distinguish between cadmium and tin rich grains. A maximum resolution of 0.017 inches was found with a calculated possibility of a resolution less than 0.002 inches"--Abstract, page ii.

Study Of Deformation Of Non-Oscillating Droplets In Liquid Media, Arun Kumar Agrawal

Masters Theses

"The object of this investigation was to find a method for predicting the deformation of non-oscillating liquid droplets which are moving in liquid media, from a knowledge of droplet size and the physical properties of the continuous and dispersed phase systems. The deformation of thirteen liquid-liquid systems was experimentally studied in this investigation"--Abstract, page i.

A Feasibility Study Of The Haeffner Effect In Mercury, Paul Martin Machmeier

Masters Theses

"An investigation of the Haeffner Effect in mercury by the use of a decade scaler suggested the need for a comprehensive statistical analysis of the data to justify reporting the presence of an isotopic separation. It has also been shown that the temperature of the mercury column must be accurately calculated before a temperature dependent relationship with the Haeffner Effect can be cited"--Abstract, page ii.

Coprecipitation Of Metal Salts With Organic Coprecipitants, Omar E. El-Arini

Masters Theses

"Coprecipitation studies were carried out for the more insoluble salts of six common metals and five anion systems. Three metal sulfides, namely, CuS, CdS and NiS, were the only metal salts studied that indicated nearly complete coprecipitation with phenolphthalein as carrier precipitate. The same salts showed almost no coprecipitation with B-naphthol as carrier precipitate. Solvent extraction of CuS with chloroform showed no significant amount of extraction had taken place. The data obtained in this work did not disclose any relationship between the extent of coprecipitation and the solubility product constant of the salt present. The main difficulty encountered at this …

Geochemical Prospecting For Copper In The Northern Part Of Yuma County, Arizona, Abdul Razak Kasim Al-Hashimi

Masters Theses

"Geochemical prospecting for copper has been carried out in two selected areas in the northern part of Yuma County, Arizona. These areas have a few old copper mines and some other zones of mineralization. The rocks of the area range in age from Precambrian to Quaternary and consist of complex gneiss, lava flows, schists, marble, sandstone, conglomerates and some intrusive dikes. A cold-extractible [sic] field method was used to study the relation between the copper content of stream sediments in washes and the geology, mineralization, and topography of the areas. A few total copper tests were also carried out. Another …

A Study Of Radiation Heat Transfer In Rectangular Ducts And Enclosures, Jenn-Wuu Ou

Masters Theses

"The purpose of this study is to determine the radiant heat transfer in rectangular configurations and construct a general computer program. Two specific cases are studied in this work. The first case is a rectangular duct with openings at each end. The duct is separated into two sections which are called the source and the sink respectively. A linear temperature profile is imposed on the source section. The energy loss of both the source and the sink is investigated. The second case is a complete rectangular enclosure. The two end plates are called the source and the sink respectively. A …

Order-Disorder In Fe₃Al At Various Temperatures Induced By Neutron Irradiation, Robert F. Toma Jr.

Masters Theses

"Resistivity measurements were made on ordered and disordered Fe₃Al samples while irradiated by neutrons.

In the ordered as well as the disorder state, the different Fe₃Al samples were heated to 100, 150, 200, 250, and 300°C respectively, and were irradiated by a fast neutron flux of 0.534 x 10¹⁰ neutrons/cm²-sec. The ordered Fe₃Al measurements were characterized by an increase in resistivity denoting an advancement toward disorder. The disordered Fe₃Al measurements were characterized by a decrease in resistivity denoting an advancement toward order. In the Fe₃Al ordered and disordered samples …

Circular Polarization From A Corner Reflector Antenna With Tilted Dipole Of Arbitrary Length, Ruben A. Carrizo M.

Masters Theses

"The problem consists of the development of the electric far field equations for a forty-five degree corner reflector antenna with a tilted dipole, of arbitrary length, centered at the corner bisector plane to produce circularly-polarized radiation. The far field expression was developed as a function of the spherical coordinate system variables and placed in Fortran language in order to determine the dipole locations which would produce circularly-polarized radiation. At such dipole locations the field patterns were plotted in the [theta] = [pi]/2 and [phi] = 0.0 planes. Computations were made by the IBM 1620 digital computer"--Abstract, page ii.

Performance Of A Reciprocating Packed Extraction Column, Thomas Vardaman Konkle

Masters Theses

"The performance of a mechanically-aided liquid extraction column was investigated utilizing the methyl isobutyl ketone-acetic acid-water ternary extraction system. Mechanical power was added to the extraction system by reciprocating a wire-mesh packing of high void volume at various frequencies and displacements. The effects of total throughput on performance were studied in increments of 5,000 pounds per hour per square foot up to the onset of flooding, and the column performance was evaluated as a function of power addition to the extraction system. In comparing the various types of mechanically-aided extraction columns, it was determined that the throughputs achieved with the …

Comparison Of Methods To Select A Probability Model, Howard Lyndal Colburn

Masters Theses

"A comparison is made between the estimates of the parameters in a gamma distribution obtained by the method of moments with those obtained by a numerical approximation to the maximum likelihood estimates. The estimates obtained by the numerical approximation had a smaller mean squared error from the true value than the estimates obtained by the method of moments. Modifications to tests of fit are made in order to develop methods to select a distribution from a set of possible distributions for a population with an unknown distribution. These selection methods are compared in their ability to make correct selections. Although …

Piezometric Levels And Shallow Aquifers, Dillon And Meramec Spring Quadrangles, Missouri, James Hugh Crouch

Masters Theses

"Little is known about groundwater in carbonate rock; quantitative data about limestone and dolomite aquifers are almost non-existent. Objectives of this study are: identification of shallow aquifers, and yield, occurrence, and piezometric level of groundwater in cherty dolomitic rocks in eastern Phelps County, Missouri. Area studied comprises of the 7.5-minute Dillon and Meramec Spring Quadrangles. The data used were derived from water well logs, interviews with well drillers and owners, and a previously available geologic map.

The Jefferson City, Roubidoux, and Gasconade formations are aquifers. Groundwater in the Jefferson City formation is perched. West and north of Dry Fork creek, …

Temperature Distribution In Thermal Boundary Layers (In Free Convection) Using A Modified Schlieren Method, Philip Ling Chen

Masters Theses

"A simple optical apparatus, the Schlieren interferometer, was constructed for the quantitative investigation of free convection heat transfer from solid bodies. The photographic results, checked by using thermocouples, were used in evaluating the temperature distribution, the key to the solution of these problems. Interpretation of the photographic results was made using the simple calculation for the conventional interferogram and the Dale-Gladstone law. Although the experiments were limited to a heated flat plate and a heated wire, two dimensional test pieces of irregular configuration can be investigated by the same apparatus with simple modifications. The photographs of the conventional Schlieren, the …

A Study Of The Influence Of Shock Waves On The Stability Of Rock-Bolt Anchorage, Helmut W. Habenicht

Masters Theses

"An experimental method was developed to compare strain data for rock and rock bolts when exposed to shock waves released by blasting. During a 32-day period of experimentation, one rock sensor and four rock-bolt sensors were observed simultaneously. By their placement in the side wall of a structurally stable drift, secondary static stresses were excluded. Bolt gage responses, then, could be considered to originate only from a decay of anchorage stability during static conditions or as a reaction to the vibrations. Interpretation of test results indicated a distinct loss in bolt-strain during vibrations, accompanied by a smaller but steady loss …

Optimum Finite Memory Nonlinear Filter, Ching-Chyoun Yang

Masters Theses

"This thesis investigates the possibility of using the Zadah theory and a machine type computer to design an optimum finite memory nonlinear filter for extraction of Poisson distributed signal pulses from a background of Gaussian noise. Basically the procedure involves the technique of solving simultaneous equations by the computer. We demonstrate that it is possible to find the limitation of the filter of class N₁ in terms of an absolute minimum mean square error. However, due to the capacity of the computer we do not actually determine the absolute minimum. Nevertheless we do show that the mean square error decreases …

The Effect Of Nickel On Activated Sludge, James Robert Matthews

Masters Theses

"The primary objective of this investigation was to determine the effect of nickel on activated sludge over a comprehensive range of concentrations and to evaluate the ability of the sludge to acclimate and become more tolerant to the metal. Six one-liter fill and draw activated sludge units were fed domestic sewage; five of these units also received constant, increasing, and shock doses of nickel while the sixth was maintained as a control. Treatment efficiency was evaluated in terms of the chemical oxygen demand, suspended solids, and nickel content of the effluent. A Warburg respirometer was also employed and was operated …

Analog Computer Study Of Unequally Spaced Antenna Arrays, Fred M. Dickey

Masters Theses

"The problem undertaken in this thesis was to study the basic properties of unequally spaced antenna arrays. The study was done on a trial and error basis by simulating the expression for the far field pattern of a general array on an analog computer. Many patterns were obtained from the analog computer for the purpose of comparison. The patterns of two spacing schemes that are typical of unequally spaced arrays are presented for the purpose of illustration"--Abstract, page ii.

Geology, Geochemistry And Genesis Of Selected Skarn Deposits, Northern New Brunswick, Canada, Donald John Bachinski

Masters Theses

"An exhaustive geological and geochemical study is presented of magnetite-chalcopyrite skarn deposits occurring within the thermal aureole of the Nicholas Denys quartz maonzonie-granodiorite stock. The deposits are crudely lenticular and occur in metamorphosed impure limestone and siliceous, in part limy, argillite-greywacke. These are now represented by andradite-epidote-diopside-calcite skarn and cal-silicate to horn-felsic rocks respectively. Both deposits are spatially related to the Main fault of the Rocky Brook-Millstream fault system; late, generally northwest trending transverse faults are conspicuous and are deemed of importance in ore localization"--Abstract, page [ii].

The Effect Of Submerged Jets On The Hydraulic Jump, Harvey E. Jobson

Masters Theses

"Tests were performed in order to determine the effects of forcing submerged jets of water into the base of a hydraulic jump. The specific energy of the water leaving the hydraulic jump, the length and the wave formation properties of the jump which had been modified by the introduction of submerged jets were determined and compared with the same characteristics of a normal hydraulic jump and a hydraulic jump which had been modified by the use of baffle piers.

Test results indicate: (a) the quantity of water flowing through the submerged jets is a primary factor in determining the specific …

The Development And Evaluation Of An Experimental Technique To Determine Stress Distribution In Uniformly Loaded Flat Plates, James William Walker

Masters Theses

"This thesis reports and evaluates an experimental technique that was developed to determine and monitor the stresses in a simply supported, uniformly loaded circular plate. Deflections are less than half the thickness of the plate. The application of the developed technique to plates whose integrity has been compromised with holes in various locations is discussed.

Resistance strain gages were used to determine experimentally the stresses in a simply supported, uniformly loaded circular plate with and without a concentric hole. The accuracy of the experimental results was established to be within approximately six percent of theoretical.

Proper application of the experimental …

The Dissolution Of Magnesium In Strong Acids And Neutral Solutions, Cheng-Ken Chi

Masters Theses

"The increasing demand for magnesium and magnesium- base alloys in the manufacture of aircraft has stimulated a great amount of research into the corrosion characteristics of these materials. The result of such research has been the development of suitable magnesium alloys and protective coatings to retard corrosion.

The basic mechanism of the anodic dissolution of metals such as magnesium, zinc, and cadmium in salt solutions is not completely known. Several schools of investigators have proposed different and opposing theories to explain the discrepancies which often arise between coulometer data and the weight loss of metal electrodes in certain salt solutions. …

Determination Of The Temperature Distribution Of The Ionized Portion Of The Jet From A Vortex Stabilized Plasma Generator Operating On Argon, G. Douglas Schellman

Masters Theses

"The interim thesis deals with the determination of the temperature distribution of a plasma jet operating on argon. It is the purpose of this thesis to present in detail the experimental process used and make a correlation of the experimental and theoretical results.

A copper enclosure was placed around the protruding flame, and the embedded thermocouple readings were taken and recorded. A stagnation temperature probe was inserted in the enclosure and moved both axially and transversely toward the flame taking readings at each pre-chosen interval. The exit temperature of the jet was obtained from a total energy balance.

From the …

The Design And Construction Of A Shock Tube Facility, William Adolph Crede

Masters Theses

"It is the object of this thesis to give an account of the considerations necessary to design, construct, and operate a shock tube facility.

The primary purpose of the facility was to provide a means to study high strength shock waves in physics, chemistry, and aerodynamic applications.

Preliminary designs were undertaken to determine the basic dimensions and related capabilities. Final design, construction and testing of the tube itself was performed by Nooter Corporation in St. Louis, Missouri. Preliminary designs agreed rather closely with final construction.

Experimental testing was confined to the successful operation of all the various components of the …