Digital Commons Network^™

A Comparison Of Strength Properties Of Heat Treated Aisi 1065 Steels At High Strength Levels, Robert Lowell Hollenbeck

Masters Theses

"Six AISI C 1065 steels were heat treated and tensile tested in order to evaluate their ductility at high strength levels. Heat treating and tensile testing procedures were developed for use working with these steels at tensile strengths of 300,000 psi and higher. The austenitizing procedure in the hardening operation was found to affect the strength and ductility of the high strength samples. Rapidly heating to the austenitizing temperature followed by an immediate quench produced better properties than slow heating followed by a soaking period before the quench. However, it was concluded that the carbon contents of the steels studied …

A New Performance Index For Sensitivity And Energy Optimization., Mohamed Zafer Dajani

Masters Theses

"The principal aim of this thesis is to present a new index of performance which when minimized will simultaneously optimize the system energy and sensitivity function of a multivariable linear control system. With this performance index it is usually desirable to discriminate between the sensitivity factor and the energy term by weighting them differently. Two types of weighting factors are presented. Since it is not easy to minimize that performance index for all types of problems, further research is suggested to find methods of solution for such problems. Illustrative examples demonstrate the optimization process and the type of assumptions needed …

A Study Of The Compressibility Of Silty Soils., Marvin L. Byington

Masters Theses

"This study has been conducted to determine the applicability of the Terzaghi Theory of Consolidation and to determine the compressibility of silt soils with varying clay content. A pure silt was extracted from the Lebanon Silt Loam and mixed with varying amounts of the Onyx Cave Illite-Chlorite Clay. The compressibility of these mixtures was determined and an attempt made to apply the Terzaghi Theory in the analysis. It was found that the compressibility of soils high in silt content is very low. It was also found that the Terzaghi Theory may be applied to mixtures of 15 percent or more …

Hot‐Film Anemometry Measurements Of Turbulence In Pipe Flow: Organic Solvents, Gary Kent Patterson, Jacques L. Zakin

Chemical and Biochemical Engineering Faculty Research & Creative Works

Longitudinal turbulence intensities, autocorrelations, and energy spectra have been measured in the flow of toluene, benzene, and cyclohexane in smooth, round 1‐ and 2‐in. I.D. tubes. These measurements were made with a constant‐temperature hot‐film anemometer and covered radial positions from the center to r/a = 0.85 in the 2‐in. tube and to r/a = 0.75 in the 1‐in. tube. The turbulence intensity data were found to be similar to those obtained for air in a 10‐in. pipe by Laufer. A slight diameter effect was observed, the intensities in the 1‐in. tube being slightly lower than those in the 2‐in. tube …

The Mechanism Of The Electrooxidation Of Acetylene On Gold, James W. Johnson, J. L. Reed, William Joseph James

Chemical and Biochemical Engineering Faculty Research & Creative Works

Acetylene has been oxidized anodically in aqueous solutions at 80 °C on gold electrodes. It was found that the partial oxidation to CO₂ was accompanied by a polymer formation. Effects of potential, acetylene partial pressure, pH, and temperature on the rate (current) were measured. A discontinuity in the Tafel curves was noted that indicated a change in the reaction mechanism with potential. The discontinuity was also pH dependent. A mechanism involving the discharge of H₂O and/or OH− has been proposed that is consistent with the experimental results. © 1967, The Electrochemical Society, Inc. All rights reserved.

The Role Of The Doctor Of Engineering Degree In Graduate Education, Wouter Bosch, Robert E. Carlile

Chemistry Faculty Research & Creative Works

No abstract provided.

Annealing Characteristics Of Neutron Irradiated Silicon Transistors, J. R. Chott, C. A. Goben

Electrical and Computer Engineering Faculty Research & Creative Works

When a transistor is subjected to neutron irradiation, a component of base current proportional to neutron fluence is induced. From the effects of annealing on the base and collector Currents the conclusion was drawn that there is an apparent difference in the annealing characteristics between the neutral and the space-charge regions of the semiconductor device. This study of the anomalous annealing indicates that the neutron-induced component of base current is a result of one, or a combination, of the following mechanisms: A quasi-tunneling recombination phenomena in the emitter-base space-charge region, or an influence of the p-n junction electric field on …

Correction To “Analysis Of The N-Wire Exponential Line”, Edward C. Bertnolli

Electrical and Computer Engineering Faculty Research & Creative Works

No abstract provided.

An Analytic Model For The Fluxgate Magnetometer, Stanley V. Marshall

Electrical and Computer Engineering Faculty Research & Creative Works

The output voltages from various fluxgate probe types are found to have the same general form, and an analytic model has been developed with which the output may be calculated. In the saturation region where the output pulse is developed, the differential permeability can be closely approximated by an exponential, dB/dH = k₁H^_k2, where k^_l and k^₂ are on the order of 100 and -2.0, respectively, for cores of Supermalloy or Permalloy 80. Using this model, the effect of the nature of the excitation function on output pulse amplitude and width and the effect …

The Design And Construction Of An Apparatus For The Plane Wave Analysis Of Mufflers, Stephen Philip Buckley

Masters Theses

"In the following report, a method for evaluating the attenuation characteristics of a general muffler as well as the design, construction and use of the associated apparatus are described. The method combines accepted plane wave theory and experimental techniques into a relatively straightforward approach to the analysis of acoustic filters. Equations are developed to cover the frequency range between 300 and 4000 cycles per second. Deviations from these equations extend the use of the equipment to low frequencies without the need for unduly long and cumbersome apparatus. This method, which may be called the standing wave method, utilizes a standing …

A Study Of Film Boiling Of Liquid Nitrogen And Liquid Argon Over A Wide Pressure Range With Cylindrical Heaters, V. J. Flanigan

Masters Theses

""A film boiling heat transfer study was conducted with three different diameter cylindrical copper heaters over a wide range of pressures for nitrogen and argon with the heat transfer surface in the horizontal position. The data were compared to the commonly used film boiling heat transfer relations. The common relations were found to be considerably in error for the range of variables covered in this investigation. A semi-empirical equation for corresponding states fluids which correlates the available data as a function of the reduced temperature and reduced pressure was derived and discussed"--Abstract, page iii.

Construction Of A Laboratory Type, Convertible Excitation Argon Laser, Arthur P. Reckinger

Masters Theses

"The purpose of this thesis is to describe the construction of a general purpose, convertable [sic] excitation, laboratory type, argon laser. Quartz tubing was used in the final model while attempts to use alumina were made during earlier work. The final model has total optical power output of 230 mw at a discharge current of 29 amperes in the dc excitation mode. Provision was also made to utilize RF or pulsed excitation. The device is built so that several values of optical transmittance are available with a wide range of mirror placement"--Abstract, page ii.

Effects Of Mixing Procedure Upon Uniformity Of Fibre Reinforced Concrete, Donald E. Nortrup

Masters Theses

"This thesis describes the effects of several methods of introducing wire fibres into a concrete mix upon the uniformity of wire fibre reinforced concrete. Various mechanical and manual methods of introducing the fibres were used and comparisons of the methods were based upon variability in splitting tensile strength and the quantitative distribution of the fibres as determined by visual inspection of sawed cylinders. Test results show that the tensile strength of concrete is increased appreciably by the inclusion of steel wire fibres in the mix and the uniformity of strength is similar to that of unreinforced concrete. The methods of …

Continuous Countercurrent Evaporation Through Porous Water-Repellent Membrane With Pressure Above Atmospheric, Yung C. Hsu

Masters Theses

"An experimental method for measuring mass transfer rates at pressures above atmospheric has been developed for the case of continuous countercurrent evaporation through porous water-repellent membranes. The final developed equipment is suitable for operation under pressures up to 50 psig and at temperatures near the boiling point of 7% salt water when high flow rates are reached. Rates of evaporation of water through the membrane were measured, and the data and results were used to examine the effects of operating conditions on the over-all mass transfer resistance. Least squares equations for fitting the data were also obtained. Over-all mass transfer …

A Programmed Synthesis Procedure For Asynchronous Sequential Circuits, Robert Judson Smith

Masters Theses

"The synthesis procedure for large asynchronous normal fundamental-mode sequential circuits is time-consuming and tedious when performed manually. This paper describes a series of computer programs which, given a machine specification in flow table form, automatically produces simplified normal form implementation design equations. The user may specify that either minimum-variable state assignments, or more rapidly generated near-minimum-variable codes be found. Next-state equations are formed using the generated state assignments and converted to simplified sums of products. Sample machines having flow tables of up to eighteen rows by four columns are synthesized"--Abstract, page ii.

A Transmission Electron Microscopy Study Of Some High Strength Plain Carbon Steels, George Joseph Vytanovych

Masters Theses

"Methods of preparing foils of high strength, heat treated, plain carbon steels for examination in the electron microscope by the transmission technique were perfected and are described. Two processes for the initial thinning of a bulk sample were successful. A chemical process was found to be more rapid but not satisfactory for small samples. A mechanical process was slower, but was applicable to the smaller specimens. Electro-polishing the thinned material yielded acceptable foils from which photomicrographs of good quality were obtained. The microstructure of the high strength steel samples showed typical tempered martensite. No reasons for the differences in ductility …

The Effect Of Concentration On The Viscosity Of Dilute And Moderately Concentrated Polymer Solutions, Hwa Luh

Masters Theses

"The effect of concentration on the viscosity of dilute and moderately concentrated polymer solutions was studied for eight narrow molecular weight polystyrene samples (900

Annealing Characteristics Of Neutron Irradiated Silicon Transistors, Joseph Robert Chott

Masters Theses

"When a transistor is subjected to neutron irradiation, a component of base current proportional to neutron fluence is induced. From the effects of annealing on the base and collector currents, the conclusion was drawn that there is an apparent difference in the annealing characteristics between the neutral and the space-charge regions of the semiconductor device. This study of the anomalous annealing indicates that the neutron-induced component of base current is a result of one, or a combination, of the following mechanisms: a quasi-tunneling recombination phenomena in the emitter-base space-charge region, or an influence of the p-n junction electric field on …

A Study Of An Electric Method To Excite And Detect Acoustic Waves In Solids, John H. Stevens

Masters Theses

"This experiment has demonstrated that it is possible to generate pulses of acoustic waves in an aluminum single crystal by the direct use of the tensile stress associated with an electric field at the surface of a conductor, and it is possible to detect these waves with a biased, capacitive pickup transducer"--Abstract, page ii.

Noble Gases In The Earth And Its Atmosphere, Robert Anthony Canalas

Masters Theses

"Abundance of noble gases extracted from Fig Tree Shale exhibit a marked deviation from the gas content of eclogitic rocks purported to be mantle material. The abundances of the heavy noble gases in shale were found to exceed the highest known meteoritic values. The abundances of the lighter noble gases were found to be comparable to the abundances of these gases in typical chondrites.

Temperature gradient analyses show that excess heavy gases are released at low temperatures. This is interpreted to indicate a preferential adsorption of the heavy noble gases on fine-grained sediments when these gases were being released from …

Lattice Constants, Thermal Expansion Coefficients, Densities, And Imperfections In Gold And The Alpha-Phase Of The Gold-Indium System, Vinayak Keshavlal Patel

Masters Theses

"An investigation of structure insensitive properties (lattice parameters, thermal expansion coefficients, densities, and imperfection) of gold and the alpha-phase of the gold-indium system was made. The gold-indium alloys were prepared from high purity (99.999%) gold and indium by melting both metals inside sealed quartz glass tubes which were first evacuated and then filled with helium gas. The solidified alloys were annealed and then examined by x-ray for homogeneity. The lattice constant of 99.999% pure gold at 25⁰C was found to be 4.07894 ł 0.00005 (corrected for refraction) Å. The coefficient of thermal expansion was 13.4 x 10⁻⁶⁰C⁻¹ between 15 and …

An Investigation Of The Effects Of An Impact On Some Of The Mechanical Properties Of Aluminum Alloy 2014-T6, Rajnikant K. Shah

Masters Theses

"Static and impact tests were conducted on an Aluminum alloy 2014-T6 specimen. The purpose of this research was to determine the effects of an impact load on some of the mechanical properties of aluminum. The cross section of the specimen measured 4.438 in. by 3.850 in. and it was 12 in. long. It was equipped with a total of four electric resistance gages connected in two pairs. One pair measured longitudinal strain while the other measured transverse strain. Both gages in each pair were mounted on the opposite sides to cancel the bending effect. In the static tests, load was …

Analog Simulation Of A Plug Flow Tubular Reactor, Jon Douglas Carson

Masters Theses

"This thesis stresses the importance of analog and digital computers in the field of reaction kinetics. The analog computer is used to simulate a chemical reaction, the hydrolysis of acetic anhydride. The hydrolysis reaction takes place in a tubular reactor. The reactor is 3/4 inch in diameter and 20 feet long. These reactor dimensions allow the reaction system to approach plug flow, if the reactants flow through the reactor at turbulent flow rates. The physical, reactor, system is used to obtain experimental data for the hydrolysis reaction. The data is obtained at reactor temperatures between 75 and 100°F. Feed concentrations …

The Economics And Design Of Desalination By Evaporation Through Porous, Water-Repellent Membranes, Kuei-Hsiung Yang

Masters Theses

"The economics of desalination by evaporation through porous, water-repellent membranes has been studied in this investigation. Using reasonable assumptions this desalination process was found to be economical with the principal advantage being the simplification of multi-stage flash-type evaporation. Based on this process, two different methods were designed and studied by means of computer calculations for a 10 million gallons product water per stream day desalting plant. One method was based on a membrane evaporator and a heat exchanger and was designated Method I; and a combined evaporation-heat exchanger system was designated at Method II. The major factors affecting the economics …

Programmed State Assignment Algorithms For Asynchronous Sequential Machines., Wayne L. Schoeffel

Masters Theses

"An important step in the synthesis procedure for realizing a normal fundamental mode asynchronous sequential circuit is the internal state assignment. Although systematic methods have been developed to construct minimum-transition-time state assignments, they become long and tedious with hand methods for machines with more than 7 or 8 internal states. To extend the application of these algorithms to larger problems, this paper presents an efficient digital computer program for generating minimum-variable state assignments. An alternate program is also presented which, though shorter, does not guarantee a minimum-variable assignment"--Abstract, page ii.

The Relation Of Heat Transfer To Mass Transfer In Vaporization Through Porous Membranes., Chung-Liang Yeh

Masters Theses

"The object of this investigation was to study the mass and heat transport phenomena through porous, water-repellent membranes. The investigation concerned the rate of vaporization of salt water at a porous membrane surface, mass transfer of vapor through the pores of the membrane, condensation of vapor on the other surface of the membrane in contact with a coolant (fresh water), and the undesired heat transfer by conduction through the membrane. The water-repellent membrane separated the two liquid phases by surface tension forces and provided a vapor phase in its pores. Membranes made of fiberglass and Teflon had been found suitable …

Negative Resistance In Cadmium Sulfide., John William Mohr

Masters Theses

"A light-sensitive, negative-resistance phenomenon has been observed in a special two-terminal CdS device fabricated from selected single crystals. The device differs from those used in previous investigations in that one end of the device was masked to keep out visible light and that the phenomenon was observed at room temperature. A method is described which enables the phenomenon to be observed on a reproducible basis. It was found that the CdS single crystal must have a relatively high density of traps. Possible mechanisms which may contribute to the phenomenon are discussed"--Abstract, page ii.

Film Boiling From Horizontal Plates With Low Thermal Capacity, K. M. Ragsdell

Masters Theses

"The object of this investigation was to obtain data for saturated film pool boiling from a low thermal capacity flat plate at atmospheric pressure. A test plate, constructed from resistance strip, was placed horizontally in a pool of liquid, and was heated electrically. Refrigerant-11 and nitrogen were used as the boiling liquids. Heat transfer results were obtained in both fluids over a temperature range of approximately 1200F⁰ (400-1600⁰F). Surface size, roughness and orientation effects were observed for flat horizontal heated surfaces with one dimension near the most dangerous wavelength. No surface material effect was observed. Excellent correlation of the data …

Shutdown Reactivity Worth Of Reactor Control Rods By A Subcritical Multiplication Method, Leslie Roger Conner

Masters Theses

"Two modified subcritical multiplication methods for measuring the reactivity worth of control elements were developed and investigated. The first involved the calibration of a subcritical count interval by the asymptotic period method. The second involved the calibration of a subcritical count interval by a rod interchange with the reactor regulating rod which had previously been calibrated by the asymptotic period method. The accuracy of these methods is relatively poor. this inaccuracy is due to shadowing effects and to the spatial harmonics which exist in the core. An investigation of the spatial harmonics to determine the best location for the neutron …

Mass Transfer From A Torus Shaped Body, Kamalesh Suryakant Desai

Masters Theses

"A mathematical model for molecular diffusion in a torus was derived. Handlos and Baron have assumed a system of tori in their eddy diffusion model for liquid-liquid extraction from droplets. However, the effect of torus curvature was neglected in their studies. Since they assumed the torus could be represented by an infinite cylinder. In this study, the effect of torus curvature was considered on the concentration profile and the fraction of the solute extracted. The partial differential equation describing the model consists of three independent variables, and a finite difference technique was employed for the solution of the mathematical model. …