Digital Commons Network^™

A Comparison Of A-C And D-C Lead Compensation From D-C Prototype Networks, Piyush Parikh

Masters Theses

"The object of this thesis is to study the difference in transient and frequency response characteristics between a prototype d-c phase lead compensating network and an equivalent a-c phase lead compensating network.

A second order servo is selected to be compensated and five d-c prototype and equivalent a-c phase lead compensating networks are designed. The frequency characteristics of the a-c networks are obtained experimentally and these of the d-c networks are obtained analytically. The characteristics of both networks are compared and their differences are studied. The transient characteristics of the d-c and a-c compensated closed-loop systems to a step input …

A Comparison Of The Load Carrying Characteristics Of Hydrostatic Thrust Bearing Using Monatomic, Diatomic, And Triatomic Gases, Joseph C. Pigott

Masters Theses

"The purpose of this investigation is to compare the load carrying characteristics of gases with different ratios of specific heat. The design, construction, and operation of an apparatus for testing and comparing the load carrying characteristics of gases are described. Several monatomic, diatomic, and triatomic gases were tested and the results evaluated and compared. The data are tabulated and displayed in a series of curves.

It was found that the monatomic gases exhibit a greater clearance for a given load and a greater total load carrying capacity than the diatomic gases which in turn have a greater clearance and total …

Transpiration Cooling Of A Heat Generating Porous Plate, M. K. A. Hameed

Masters Theses

"This investigation is a continuation of a thesis by T. S. Purewal. Several of the simplifying assumptions made by the above author are either ignored or the justifiability of such assumptions is probed into in order to obtain a more rigorous solution. Effects of the assorted grain size, non-Newtonian cooling, direction of coolant flow, thickness of the porous heat generating plate, specific heat of the coolant, and compressibility of the coolant are investigated in this thesis. Variation of maximum temperature of both coolant and the solid material for different types of heat source distribution are also studied.

As the grain …

Glass-To-Sapphire End Window Seals, Edward E. Stepp, Richard A. Anderson

Physics Faculty Research & Creative Works

SAPPHIRE windows have been used in laboratory devices where radiation from the ultraviolet through the infrared must be transmitted. Sapphire windows have been valuable in chambers which contain the alkali metals, for the alkali metals are known to react with Pyrex 7740 glass and quartz leaving them pitted and darkened. This paper is a report on an improved glass-to-sapphire end window seal.

A Model Study Of The Behavior Of Elastic Liners In Shallow Underground Openings, Martin Samuel Oudenhoven

Masters Theses

"Models of epoxy resin were used in a stress freezing technique to determine areas of possible failure in lined circular openings. These models were loaded in a centrifuge for a fixed period of time, after which they were analyzed photoelastically. The material characteristic changes, with time, were recorded on graphs and used in the analysis.

Two types of tests were conducted; one, where the lining thickness was changed and, the other, where materials of the liner and plate material were changed.

The resulting analyses furnished proof that the greater the rigidity of the lining, the higher the stress developed in …

A Study Of The Electro-Chemical Injection Of Ca(Oh)₂ Into Pure Kaolin Clay, Sam Michael Savas Jr.

Masters Theses

"The work presented in this thesis is the investigation and study of a possible and successful means of injecting an electrolyte solution into a fine grain soil mass with the use of electric current and to measure some of the changes of its physical properties. A NoKarb Georgia Kaolin Clay was treated by passing a preferential electrolyte solution of Ca(OH)₂ using direct current for a period of one and six days. The tests performed during this investigation included the following: (a) tri-axial tests, (b) atterberg limits, (c) pH determination, (d) moisture content change (from treatment), (e) visual settling of treated …

A Study Of The Problems Of Design Of Optimum Vibration Absorbers For Multi-Mass Systems, James C. Villegas

Masters Theses

"The purpose of this investigation was to continue the preliminary work of Burrows on the application of tuned and damped vibration absorbers to the reduction of vibratory stresses in a multi-mass torsional vibration system. A hypothetical engine system was chosen for both investigations because it had many complicating factors and gave an eminently practical subject for study.

Attention was centered on the reduction of stresses resulting at higher speeds of the machine system and on developing methods and criteria for the designing of effective absorbers where several modes of vibration exist in the operating speed range of the machine"--Abstract, page …

A Study Of The Stress Distribution Around Circular Openings Using Multilayered Photoelastic Material, Donald Frank Haber

Masters Theses

"Stress analysis as applied to mine openings ranges from the completely empirical to the completely theoretical. However, it is only through the ultimate utilization of the two methods that a guide to the Interpretation of mine stress phenomenon may be obtained. The bridge between the two approaches lies in the field of model study. Specifically, this is an Investigation into determining the feasibility of using multilayered photoelastic materials in models such that a more exact approximation of the underground stress distribution around mine openings can be made.

The two major objectives in this study for determining the feasibility of using …

Model Analysis By The Moiré Method, David D. Kick

Masters Theses

"This study presents the use of Moiré fringes for model analysis of deflections and strains. Deflection of a beam, strain in a disk, and an Influence diagram for a frame are presented as examples of uses of the Moiré method. The necessary equations for the determination of strain using the Moiré method are also derived and presented in this work"--Abstract, page v.

Porous Cooling Of A Pile, Tarsem Singh Purewal

Masters Theses

"In this investigation the problem of a limiting case of steady state one dimensional solid-fluid Newtonian heat transfer is examined in which an incompressible non-heat generating coolant fluid is flowing through a heat generating porous plate.

The effect of grain size on the Newtonian heat transfer in the porous plate with various kinds of internal heat generations is determined analytically. The temperature difference between the solid and the coolant fluid through the porous plate is determined. All the previous studies assume that in the porous plate, coolant fluid temperature and solid temperatures are approximately equal. This analysis eliminates this simplifying …

A Study Of Several Commercial Steels In The Red Short Range, Jorge Alberto Espana

Masters Theses

"The red short phenomenon present in steel, was studied by means of torsion tests at temperatures between 800 and 1200⁰C. Cold drawn bars of different compositions of steels were tested, and the number of turns to failure and maximum twisting torque were plotted versus temperature.

All the steels tested, exhibited to have a certain degree of red shortness. By comparing the curves and the respective chemical analyses, the detrimental effect of sulphur and lead and the beneficial effect of manganese, was established.

Microscopic examinations revealed the intergranular nature of the cracks in the red short range. Sulphur and oxide distribution …

Permeability Of Poly (Ethylene Terephthalate), James G. Harvey

Masters Theses

"Corrosion is a phenomenon which has been the subject of extensive research, in order to find a way to control or completely stop it. Two general methods, either placing the material which corrodes in an anti-corrosive atmosphere or protecting the material which corrodes from the corrosive atmosphere, are the chief means of preventing corrosion today.

The second method is probably most widely used presently. One of the most important methods of protection is by means of organic protective coatings, or paints, but at best these only retard corrosion, due to the fact that corrosive media e.g. water vapor, ions etc. …

Development Of A Simple Bar Method Thermal Conductivity Test, V. J. Flanigan

Masters Theses

"A linear flow bar method type apparatus was set up for finding thermal conductivities by comparison techniques. Comparison technique consist of using a standard specimen where the thermal conductivity is known and comparing it to the unknown specimens to find their conductivity. Apparatus of this type usually uses thermocouples for the required temperature measurements, but thermistors were used in this experiment. The thermistors used required calibration to measure accurate temperatures and this was accomplished by using the known temperatures of the changes of state of some common materials. Five alloys were used to evaluate the method: SAE 1020 steel, gray …

The Effect Of The Rolling Load On The Micro-Structure Of Low Carbon Sheet Steel, Jerry Lee Cadden

Masters Theses

"A Stanat 315, two high-four high, combination rolling mill is used to cold roll annealed, low carbon steel strips. A method of measuring the rolling load was presented. The method consisted of constructing a load cell using SR-4 strain gages attached to a steel column. The load cell was placed under the hold down screw of the rolling mill and a known load was applied. The stresses from this load were transferred to the mill housing where another SR-4 strain gage was located. The strain in the mill housing was recorded at the corresponding applied load. During rolling, the strain …

Transpiration Cooling Of A Porous Plate, Stephan A. Sayegh

Masters Theses

"Transpiration cooling has long been known as an effective way of removing heat from porous materials. This thesis is a new approach to one of the problems of transpiration cooling in the steady state.

The specific problem considered here is that of a uniform porous plate through which a liquid is forced. This liquid vaporizes at a short distance from the surface through which it is forced and leaves the porous plate at the other surface which is exposed to hot gases. It also protects the hot surface by forming an insulating layer between that surface and the hot gases. …

Mechanics Of The Voussoir Arch As Applied To Block Caving, Christopher Haycocks

Masters Theses

"The theories of ground failure in massive rock with special reference to the problem of the mechanics of block caving were studied and evaluated.

The mechanics of arch or dome formation underground were studied quantitatively using the Voussoir arch theory. The effect of shear stress on the arch stability was considered and found to affect the system only when the arch height increased beyond certain limits.

A theory of the mechanism of ground failure in an undercut block using the dome theory was advanced. Photo- elastic model studies were used to support the conclusions reached"--Abstract, page i.

An Investigation Of Lehmer's Method For Finding The Roots Of Polynomial Equations Using The Royal-Mcbee Lgp-30, James W. Joiner

Masters Theses

“The solution of the general polynomial equation f (x) = O, where f(x) = a_nxⁿ + a_n-1x^n-1 + … + a₁x = a_o, has received the attention of many mathematicians for hundreds of years and is at present in a very highly developed state. Even a cursory examination of the literature will reveal many volumes on this subject. However, this study is concerned primarily with the numerical methods for solving polynomial equations, hence the classical methods will be treated here only as they contribute to this field.

Virtually all of …

Thermal Conductometer For Liquids, Yuan-Kai Chang

Masters Theses

"The published data pertaining to the thermal conductivity of liquids are of such a character that it is very difficult to determine from them the correct value, or the temperature coefficient for any liquid.

Most of the published values of thermal conductivity for liquids are evaluated at one particular temperature. It is the purpose of this investigation to design, construct and calibrate a thermal conductometer for liquids over a temperature range of 30°F to 200°F.

Since water and glycerol were the only liquids found by this investigator with published data on their conductivities as a function of temperature, they were …

Electrodeposition Of Antimony From Sulfide Melts, Mahendra N. Rana

Masters Theses

"A study of the current-potential relationships, and the electrodeposition of antimony metal was conducted for fused mixtures of Sb₂S₃-Na₂S, Sb₂S₃-Sb and Sb₂S₃-NaCl-KCl in the temperature range of 700° - 900°C. An attempt was made to determine the mutual solubility of molten antimony and Sb₂S₃-Na₂S melts. The microstructure of deposited metal was studied metallographically. Analysis of phases present in the matte mixture (Sb₂S₃-Na₂S) was made by x-ray diffraction patterns.

All investigations were carried out in …

A Survey Of The Influence Of Selected Sulfides On The Thermal Decomposition Rate Of Zinc Sulfate, L. G. Twidwell

Masters Theses

"The influence which ZnS, CdS, Cu₂S, PbS, and FeS has on the thermal decomposition rate of ZnSO₄ was studied by measuring the SO₂ gas evolved per unit of time for various ZnSO₄-MeS mixtures at 600°C, and analyzing the solid phases by means of X-ray diffraction patterns.

The SO₂ gas evolved upon heating the pellets was analyzed as a function of time by absorbing the gas in a solution of distilled water, H₂O₂, and NaOH, and measuring the time required for the SO₂ to neutralize the NaOH. The gas …

The Missouri Miner, October 27, 1961

The Missouri Miner Newspaper

No abstract provided.

Missouri S&T Magazine, October 1961, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

Perfection Of The Lattice Of Dislocation-Free Silicon, Studied By The Lattice-Constant And Density Method, Martin E. Straumanis, Pierre Borgeaud, William Joseph James

Materials Science and Engineering Faculty Research & Creative Works

The lattice-constant and density method revealed that a high-purity silicon crystal free of dislocations has a perfect lattice without an excess of vacant sites or interstitials (n′=8.0000 4) within the limits of error, in agreement with the results obtained with the decoration method. The lattice constant of vacuum heated silicon powder of semiconductor purity was 5.43070±0.00004 A; that of the nonheat-treated powder was 5.43081 A at 25°C. The constants determined from crystal chips by the rotating crystal method were lower: between 5.43028-5.43048 A at 25°C. As the constants of each series of measurements could be reproduced very well (s=±0.00004 A), …

Missouri S&T Magazine, June 1961, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

Missouri S&T Magazine, February 1961, Miner Alumni Association

Missouri S&T Magazine

No abstract provided.

The Rollamo 1961, The University Of Missouri School Of Mines And Metallurgy

Yearbooks

No abstract provided.

An Analog Method For The Determination Of The Deflection Of Beams Resting On End Supports And Design Of An Automatic Programming Device, Paul C. Jackson Jr.

Masters Theses

"This investigation shows that beam problems can be solved easily and accurately with an analog computer. Two problems were solved as to their shear, moment, slope and deflection along the length of the beam and the graphs drawn by the analog computer were compared with calculated values. Very little difference was found between them.

An electronic programmer was built to aid in handling beam problems as they were being run on the computer. This was capable of putting into the computer bits of data at specified intervals of time. The programmer proved reliable and repeatable once it was adjusted to …

Use Of Light-Weight Steel Strapping As External Reinforcing To Concrete Beams, John O. Buchanan

Masters Theses

"As a result of some recent failures in reinforced concrete construction throughout the United States, a study was made by several national authorities to find some remedial measures of strengthening existing structures without rebuilding. A system was developed, using high strength steel bands applied externally to beams, to act as stirrups, which has been highly successful. It not only greatly increased the strength of beams already in place but was used to repair members which had already failed.

The application of these bands was made under very exact specifications, using closely controlled procedures, with many physical refinements, in order to …

A Method Of Estimating Groundwater Influx Into A Vertical Mine Shaft, Morris T. Worley

Masters Theses

"Prediction of groundwater influx into mine openings is one of the more important pre-development problems encountered in mining. A satisfactory method of estimation would provide the information necessary for a mining company to dewater prior to shaft sinking, pre-grout the shaft area, or plan pumping schemes to handle the expected flow.

A standardized field method of estimating groundwater supply from pumping test data was developed by O. V. Theis and others. In the present research problem, the estimation procedure has been simplified by the use of nomograms. Certain modifications in the estimate must be made when a pumping well is …

Effects Of Calcining Temperature On The Physical Properties Of Zirconate Ceramics, P. D. Ownby

Materials Science and Engineering Faculty Research & Creative Works

No abstract provided.