Open Access. Powered by Scholars. Published by Universities.®

Digital Commons Network™

Open Access. Powered by Scholars. Published by Universities.®

Missouri University of Science and Technology

Discipline
Keyword
Publication Year
Publication
Publication Type
File Type

Articles 16231 - 16260 of 17246

Full-Text Articles in Entire DC Network

A Closed Form Method For Predicting The History Of Circular Orbit Altitude Decay Of A Near-Earth Satellite Including The Effect Of A Dynamic Atmosphere, John Copley Buchholtz Jan 1971

A Closed Form Method For Predicting The History Of Circular Orbit Altitude Decay Of A Near-Earth Satellite Including The Effect Of A Dynamic Atmosphere, John Copley Buchholtz

Masters Theses

"A closed form expression for the time to decay between two circular orbit altitudes is developed. The long-term dynamic variation of high altitude atmospheric density is included. The density is approximated as a ratio of two quadratics with the numerator being a function of the time-related exospheric temperature and the denominator being a function of altitude. The 11-year cyclic variation of exospheric temperature is then represented as a piecewise linear function of time. The analytic expression for circular orbit altitude decay rate is developed by describing the energy loss due to atmospheric drag. A point mass representation of the Earth's …

Go to article

The Influence Of Member Length On Thermal Contact Resistance In A Vacuum Environment, Larry Martin Cooper Jan 1971

The Influence Of Member Length On Thermal Contact Resistance In A Vacuum Environment, Larry Martin Cooper

Masters Theses

"An investigation was conducted to determine the influence of member length on thermal contact resistance in a vacuum environment. A model was created which consisted of a center rod axially loaded between two other members. It was assumed that circular macroscopic constriction areas were formed at the contact interface when the rods were loaded. Macroscopic modeling of the contact surfaces makes the thermal contact analysis a function of the mechanical and thermal boundary conditions of the total body. The method of finite differences was employed to calculate the temperature distribution, heat flows, and thermal contact resistance of each member. Data …

Go to article

Integrability Of The Sums Of The Trigonometric Series 1/2 Aₒ + ∞ [Over] Σ [Over] N=1 AN Cos Nθ And ∞ [Over] Σ [Over] N=1 AN Sin Nθ, John William Garrett Jan 1971

Integrability Of The Sums Of The Trigonometric Series 1/2 Aₒ + ∞ [Over] Σ [Over] N=1 AN Cos Nθ And ∞ [Over] Σ [Over] N=1 AN Sin Nθ, John William Garrett

Masters Theses

"The trigonometric series C = 1/2 aₒ + ∞ [over] Σ [over] [n=1] a[subscript n] cos nΘ and S = ∞ [over] Σ [over] n=1 a[subscript n] sin nΘ, where {a[subscript n]} monotonically decreases to zero both converge almost everywhere to functions f and g respectively. f (or g) is L iff C (or S) is the Fourier series of f (or g) iff term-by-term integration of C (or S) is valid. There are three equivalent conditions, each of which implies that C is the Fourier series of f...."--Abstract, page ii.

Go to article

Laminar Heat Transfer For Small Prandtl Number Fluids Including Step Change In Wall Temperature, Shiny Ting Jan 1971

Laminar Heat Transfer For Small Prandtl Number Fluids Including Step Change In Wall Temperature, Shiny Ting

Masters Theses

"The object of this investigation is to provide a simple means of determining the heat transfer from a flat plate which has an unheated leading length x₀. The case of steady, two-dimensional, laminar flow of an incompressible fluid with a Prandtl number of less than one is considered. Since there exists an unheated length and the Prandtl number of the fluid is less than one, the thermal boundary layer intersects the flow boundary layer. Thus, the solution of the problem divides into two regions. In this study, the problem is solved analytically by employing the energy integral equation. The temperature …

Go to article

Compressibility Effects On Transient Gas Pipe Flow, Gerald Francis Mouser Jan 1971

Compressibility Effects On Transient Gas Pipe Flow, Gerald Francis Mouser

Masters Theses

"Abstract (1) Methods of iterative solution for the partial-differential equations that govern the transient flow of gases in pipelines are obtained by using the method of characteristics and linear finite-difference techniques. Solutions are developed for 1) a constant gas compressibility factor throughout transient conditions, and 2) a variable gas compressibility factor at constant temperature dependent upon pressures encountered during transient flow. Theoretical studies are made to compare results using both approaches for pipelines operating at various constant flowing temperatures. Results show greater differences between the two methods at lower values of flowing temperature due to the more rapidly changing compressibility …

Go to article

Development Of An Elastic-Plastic Finite Element Program With The Initial Strain Approach, Vernon Dale Allen Jan 1971

Development Of An Elastic-Plastic Finite Element Program With The Initial Strain Approach, Vernon Dale Allen

Masters Theses

"A finite element method is presented for solution of plane stress and axisymmetric elastic-plastic problems employing the method of successive elastic solutions with the initial strain approach. The problem of nonconvergence of the initial strain approach for perfectly plastic problems was eliminated by expressing the Prandtl-Ruess equations entirely in terms of strain. Two examples are presented to demonstrate the validity of the method"--Abstract, page ii.

Go to article

High Temperature Compressive Creep In Mullite, Peter C. Smith Jan 1971

High Temperature Compressive Creep In Mullite, Peter C. Smith

Masters Theses

"Compressive creep measurements were made on two groups of mullites at temperatures between 1455ºC and 1520ºC. The first group consisted of commercially manufactured mullites. The second group was made up of 7 different mullite compositions spanning the alumina-silica solid solution range from 3Al₂O₃ • 2SiO₂ to 2Al₂O₃ • SiO₂ . Thermal activation energies and stress exponents were calculated for the mullites in the second group. Steady state strain rates taken at 1460ºC under loads of 100 and 110 psi varied between 1.3x10⁻⁴ in/in/hr and 15.4x10⁻⁴ in/in/hr. Activation energies were between 109 Kcal/mole and 204 Kcal/mole. Stress exponents calculated from data …

Go to article

An Age Hardening Study Of Magnesium-Thorium-Manganese Alloys, Kuldip Singh Chopra Jan 1971

An Age Hardening Study Of Magnesium-Thorium-Manganese Alloys, Kuldip Singh Chopra

Doctoral Dissertations

"The age hardening processes in Mg-3.5 wt.% Th-1.0 wt.% Mn and Mg-1.0 wt.% Th-1.0 wt.% Mn alloys have been studied by light and electron microscopy, and by electron and X-ray diffraction. At aging temperatures of 300ºC and below, G.P. zone formation rapidly hardens these alloys followed by the precipitation of disc shaped plates during averaging. During aging above 300ºC, no G.P. zones form and the disc shaped precipitate grows to very large sizes. The combined results of X-ray and electron diffraction indicate that the disc shaped precipitate has a Mg₃Cd (DO₁₉) type structure. The basal plane of the Mg₃Th discs …

Go to article

Synthesis, X-Ray Characterization, Structural And Magnetic Studies Of A New Class Of Iso-Structural Bimo₃ Compounds, Joseph Donato Bucci Jan 1971

Synthesis, X-Ray Characterization, Structural And Magnetic Studies Of A New Class Of Iso-Structural Bimo₃ Compounds, Joseph Donato Bucci

Doctoral Dissertations

"This dissertation consists of four sections. The first part is a temperature dependent X-ray study of the lattice parameters of BiFeo₃. The synthesis and subsequent X-ray characterization of BiCo₃, BiAlO₃, BiMnO₃ , BiScO₃, BiCo₁₋ₓFeₓO₃ , and BiAl₁₋ₓFeₓO₃ are reported in the second part. These compounds all crystallize in the body centered cubic (BCC) structure with a~10.2Å. Single crystal Precession and Weissenberg photographs confirmed the BCC structure. In part three, the results of the magnetic studies on BiCoO₃ and biAl.₉FE.₁ are presented. The magnetic data for BiCoO₃ are substantiated by X-ray thermal expansion studies. In the last part the compound BiCo.₉FE.₁O₃ …

Go to article

Photoionization Of Photoexcited Cesium, Robert E. Hebner Jan 1971

Photoionization Of Photoexcited Cesium, Robert E. Hebner

Doctoral Dissertations

"A new method for obtaining the cross section for photoionization of photoexcited cesium is presented. The salient feature of this experiment is to use three crossed beams, i.e., two light beams intersecting a beam of cesium atoms. The cross section is determined by counting the ions produced by the two step process: Cs (6S) + h[upsilon]₁ --> Cs (6P) ; Cs (6P) + [upsilon]₂ --> Cs⁺ + e⁻ The relative cross section for the second step has been obtained from threshold (5060 Å) to 2500 Å. The excitation light source used in obtaining this cross section was a rf resonance …

Go to article

Dynamic Behavior Of Eccentrically Stiffened Plates, Charles Stuart Ferrell Jan 1971

Dynamic Behavior Of Eccentrically Stiffened Plates, Charles Stuart Ferrell

Doctoral Dissertations

"The dynamic behavior of eccentrically stiffened rectangular plates is studied by the finite element method. The addition of stiffeners to a plate structure is a common method of increasing the rigidity of the structure with a minimum of weight increase. However, this stiffened plate configuration does not easily lend itself to analysis. This study is an approach to finding a rational method by which the dynamic behavior of such a stiffened plate structure may be determined. The governing differential equations for the finite element model are derived and the stiffness and mass matrices for the plate and stiffener elements are …

Go to article

Metal Salt Catalyzed Carbenoids, Billy W. Peace Jan 1971

Metal Salt Catalyzed Carbenoids, Billy W. Peace

Doctoral Dissertations

"The interaction of diazomalonic esters with olefins in the presence of homogeneous copper(I) and copper(II) catalyst has been examined as a function of olefin structure, solvent media, ionic strength, catalyst structure and catalyst concentration, using partial rate data. It has been possible to determine the fine mechanistic details of the cycloproponation, C-H insertion and "dimer" forming reactions. The initial step is displacement of a ligand from copper by diazo compound in a pre-equilibrium, loss of nitrogen in the rate determining step, return of the ligand, displacement of metal from the carbenoid by olefin, followed by collapse to products. Studies revealed …

Go to article

Noble Gases Anomalies In Terrestrial Ores And Meteorites, B. Srinivasan Jan 1971

Noble Gases Anomalies In Terrestrial Ores And Meteorites, B. Srinivasan

Doctoral Dissertations

"Analyses of the content and isotopic composition of xenon and krypton in terrestiral ores containing tellurium, selenium or iodine resulted in the following conclusions: 1. The double beta-decay half-life for ¹³⁰Te is 2.51 x 10²¹ years from analysis of tellurobismuthite from Boliden, Sweden and 2.83 x 10²¹ years from analysis of tellurides from Kalgoorlie, Australia. 2. The ratio of the double beta-decay half-life of ¹²⁸Te relative to that of ¹³⁰Te is ≥ 108 and ≥ 293 for Boliden tellurobismuthite and Kalgoorlie tellurides, respectively. 3. Selenium minerals and tellurium ores containing selenium exhibit ⁸²Kr excess attributed to the double beta-decay of …

Go to article

Identification Of Linear Systems With Delay Via A Learning Model, Hugh Francis Spence Jan 1971

Identification Of Linear Systems With Delay Via A Learning Model, Hugh Francis Spence

Doctoral Dissertations

"The effects of input delay on an identification scheme using a learning model are investigated. The parameter adjustment laws for the learning model are derived through Lyapunov methods similar to those used for the model reference adaptive control systems of Parks. For no measurement noise or delay mismatch between the learning model and system, the parameters are adjusted to bring the error between model and plant to zero. When there is delay mismatch between the inputs of the learning model and the unknown system, the convergence of the parameters of the learning model to those of the unknown system is …

Go to article

Surface Reactions Of Boron With Clean Tungsten Substrates, Thomas A. Flaim Jan 1971

Surface Reactions Of Boron With Clean Tungsten Substrates, Thomas A. Flaim

Doctoral Dissertations

"A model developed to predict adsorbate-induced work-function changes for thermionic emitters is shown here to apply to a more general class of electron emission phenomena and a much broader range of adsorbates. This model predicts that chemically, vapor-deposited boron will increase the work function of a clean tungsten substrate at coverages between 0 and 1 monolayer. This is the first time that a single model has been shown to predict both positive and negative work function changes for different adsorbates. The reactions of chemically, vapor-deposited (CVD) boron with clean tungsten substrates were studied using field emission microscopy (FEM) and low …

Go to article

The Effect Of Channel Errors In The Differential Pulse-Code-Modulation Transmission Of Sampled Imagery, Roger J. Arguello, Harvey R. Sellner, John A. Stuller Jan 1971

The Effect Of Channel Errors In The Differential Pulse-Code-Modulation Transmission Of Sampled Imagery, Roger J. Arguello, Harvey R. Sellner, John A. Stuller

Electrical and Computer Engineering Faculty Research & Creative Works

This Paper Presents an Analysis, Simulation, and Discussion of the Effects of Communication Errors on Four-Bit Differential Pulse-Code Modulation (DPCM) Sampled Imagery. Simulations Are Presented that Describe the Effects of Inserting Periodic "PCM Updates" in Order to Correct Communication Errors in the DPCM Transmission of Photographic Scenes that Have Been Scanned and Sampled at the Nyquist Rate. Copyright © 1971 by the Institute of Electrical and Electronics Engineers, Inc.

Go to article

Maximum-Distance Linear Codes, Gary K. Maki, James H. Tracey Jan 1971

Maximum-Distance Linear Codes, Gary K. Maki, James H. Tracey

Electrical and Computer Engineering Faculty Research & Creative Works

Described here is a linear code that has a maximum distance between codewords of k for a code of order 2k. Since the minimum-maximum distance is k for a code of order 2k, a class of minimum-maximum distance codes results. For an (n,k) linear code, k ≤ n ≤ k + k∣2 for k even and k ≤ n ≤ k + (k - 1)/2 for k odd. Maximum-distance codes are found useful in encoding the states of sequential circuits. © 1971, IEEE. All rights reserved.

Go to article

Deriving Dc Machine Torque By The Principle Of Virtual Work, George Mcpherson Jan 1971

Deriving Dc Machine Torque By The Principle Of Virtual Work, George Mcpherson

Electrical and Computer Engineering Faculty Research & Creative Works

The purpose of this paper is to fill a gap which exists in the "textbook" theory of dc machines. The paper shows that the usual expression for dc machine torque can be obtained from the direct application of the principle of virtual work to the machine, making the traditional assumptions. The method provides additional benefits in that it demonstrates the reluctance torque which results from the saliency of the field structure and shows that compensating windings have no effect on the torque under the assumed linear conditions. Copyright © 1971 by The Institute of Electrical and Electronics Engineers, Inc.

Go to article

Electrical Engineering Education In An Industrial Laboratory, J. Derald Morgan Jan 1971

Electrical Engineering Education In An Industrial Laboratory, J. Derald Morgan

Electrical and Computer Engineering Faculty Research & Creative Works

This paper describes a unique electrical engineering laboratory course. This laboratory is an example of industry-uni-versity cooperation in engineering education. The organization and operation of the course is outlined and explained. The educational benefits derived from such cooperation between industry and the university are briefly detailed. These benefits are extended to the students, the university, the faculty, and the participating industry. This paper provides the framework and challenge to industry from which other laboratory experiences can be conceived and developed. Copyright © 1971 by The Institute of Electrical and Electronics Engineers, Inc.

Go to article

A State Assignment Procedure For Asynchronous Sequential Circuits, Gary K. Maki, James H. Tracey Jan 1971

A State Assignment Procedure For Asynchronous Sequential Circuits, Gary K. Maki, James H. Tracey

Electrical and Computer Engineering Faculty Research & Creative Works

This paper presents a new procedure for constructing nonuniversal shared-row internal state assignments for asynchronous sequential circuits. The method consists basically of establishing an initial code with the minimum number of variables required to dis. © 1971, IEEE. All rights reserved.

Go to article

A Gamma-Level Portable Ring-Core Magnetometer, Stanley V. Marshall Jan 1971

A Gamma-Level Portable Ring-Core Magnetometer, Stanley V. Marshall

Electrical and Computer Engineering Faculty Research & Creative Works

A four-transistor circuit is described for a battery-operated magnetometer that has 0.1 γ resolution using t-in diameter 4–79 or 6–81 Mo-Permalloy tape cores of 20–40 Mx capacity. The center-tapped drive winding also serves as the sense winding, simplifying the sensor assembly. Some signal-to-noise results are presented to illustrate the fairly wide difference that may exist between cores of the same cross section and to demonstrate the advantage of reducing core area. Copyright © 1971 by The Institute of Electrical and Electronics Engineers, Inc.

Go to article

Empirical Bayesian Learning, David R. Cunningham, Arthur M. Breipohl Jan 1971

Empirical Bayesian Learning, David R. Cunningham, Arthur M. Breipohl

Electrical and Computer Engineering Faculty Research & Creative Works

It is shown that a certain weighted average of the prior distribution and the empirical distribution yields an estimate of the posterior distribution that is consistent with Bayes' theorem. Acomparison of this approach and conventional parametric Bayesian estimation is made for some specific cases. Copyright © 1971 by The Institute of Electrical and Electronics Engineers, Inc.

Go to article

The Axial Contact Of Finite Elastic Cylinders With Application To Thermal Contact Resistance, Ross Orlo Mcnary Jan 1971

The Axial Contact Of Finite Elastic Cylinders With Application To Thermal Contact Resistance, Ross Orlo Mcnary

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Predictions of the macroscopic thermal contact resistance have been severely restricted because the macroscopic contact area between finite members could not be determined. A new method of solution to this contact problem in elasticity is developed which is applicable to a wide variety of geometries and boundary conditions. A physical lumped-parameter model is employed from which the finite difference equations in terms of displacement are derived. Calculations using this method indicate that large errors in the prediction of the thermal contact resistance can result if solutions for bodies of infinite extent are employed for finite regions of interest. Especially large …

Go to article

Charges On Jet Drops Produced By Bursting Bubbles, Robert A. Medrow, B. T. Chao Jan 1971

Charges On Jet Drops Produced By Bursting Bubbles, Robert A. Medrow, B. T. Chao

Mechanical and Aerospace Engineering Faculty Research & Creative Works

The sizes and charges of jet drops produced by bursting air bubbles are examined experimentally. The variation in charge for bubble lifetimes of up to 200 sec in NaCl and KCl solutions is reported. Jet drops refer to drops produced by a jet rising from a cavity left in a liquid surface by a bursting bubble; bubble lifetime is the interval during which a bubble is in motion between generation and rupture. With other variables held constant, drop charge shows a characteristic variation of a rise to a maximum followed by a decrease to an asymptotic value, as bubble lifetime …

Go to article

Conversions From Cyclohexanol: An Undergraduate Laboratory Project, Samir B. Hanna, James T. Wrobleski, Joseph T. Bohanon, Billy W. Peace Jan 1971

Conversions From Cyclohexanol: An Undergraduate Laboratory Project, Samir B. Hanna, James T. Wrobleski, Joseph T. Bohanon, Billy W. Peace

Chemistry Faculty Research & Creative Works

No abstract provided.

Go to article

Diffusion Coefficients Of Ethylene Glycol And Cyclohexanol In The Solvents Ethylene Glycol, Diethylene Glycol, And Propylene Glycol As A Function Of Temperature, Ronald D. Mitchell, James W. Moore, Robert M. Wellek Jan 1971

Diffusion Coefficients Of Ethylene Glycol And Cyclohexanol In The Solvents Ethylene Glycol, Diethylene Glycol, And Propylene Glycol As A Function Of Temperature, Ronald D. Mitchell, James W. Moore, Robert M. Wellek

Chemical and Biochemical Engineering Faculty Research & Creative Works

No abstract provided.

Go to article

Internal Friction Of Ion Exchanged Li₂O•Al₂O₃•2sio₂ Glasses, A. Ismail A. Abdel-Latif Jan 1971

Internal Friction Of Ion Exchanged Li₂O•Al₂O₃•2sio₂ Glasses, A. Ismail A. Abdel-Latif

Doctoral Dissertations

"Li₂O•Al₂O₂•2SiO₂ glass fibers were ion-exchanged from 1 to 300 minutes in a sodium nitrate bath at 366ºC. The internal friction was measured along with the lithium and sodium concentration profiles. As sodium progressively replaced lithium, the alkali internal friction peak became smaller while a new peak (mixed alkali peak) appeared and increased in magnitude. These changes in the internal friction are similar to those that occur upon the addition of a second alkali to glasses prepared by conventional melting. The magnitude of both internal friction peaks in ion exchanged glasses was dependent on the overall glass composition. The magnitude of …

Go to article

Bayesian Confidence Limits For The Reliability Of Mixed Exponential And Distribution-Free Cascade Subsystems, Melvin D. Springer, James K. Byers Jan 1971

Bayesian Confidence Limits For The Reliability Of Mixed Exponential And Distribution-Free Cascade Subsystems, Melvin D. Springer, James K. Byers

Computer Science Faculty Research & Creative Works

The problem treated here is the theoretical one of deriving exact Bayesian confidence intervals for the reliability of a system consisting of some independent cascade subsystems with exponential failure probability density functions (pdf) mixed with other independent cascade subsystems whose failure pdf's are unknown. The Mellin integral transform is used to derive the posterior pdf of the system reliability. The posterior cumulative distribution function (cdf) is then obtained in the usual manner by integrating the pdf, which serves the dual purpose of yielding system reliability confidence limits while at the same time providing a check on the derived pdf. A …

Go to article

Anodic Dissolution Of Beryllium In Anhydrous Media, William Joseph James, Martin E. Straumanis Jan 1971

Anodic Dissolution Of Beryllium In Anhydrous Media, William Joseph James, Martin E. Straumanis

Chemistry Faculty Research & Creative Works

No abstract provided.

Go to article

The Oxidative Decarboxylation Of Polyaminocarboxylic Acids - Ii. A Comparative Kinetic Study Of The Oxidation Of Nta, Edta, Cdta And Dtpa With Cerium(Iv) In Sulfuric Acid Media, Samir B. Hanna, Rita Hessley, William H. Webb, William R. Carroll Jan 1971

The Oxidative Decarboxylation Of Polyaminocarboxylic Acids - Ii. A Comparative Kinetic Study Of The Oxidation Of Nta, Edta, Cdta And Dtpa With Cerium(Iv) In Sulfuric Acid Media, Samir B. Hanna, Rita Hessley, William H. Webb, William R. Carroll

Chemistry Faculty Research & Creative Works

The rates of oxidation of four chelating agents, NTA, EDTA, CDTA, and DTPA with Ce(IV), in sulfuric acid media, were determined spectrophotometrically by a stopped-flow technique. The reductive ability is in the order CDTA > EDTA > DTPA > NTA. The influence of varying the acidity of the medium was studied, and in each case a maximum in the rate constant vs. [H+] plot was observed. A possible interpretation of the reactivities and the influence of acidity is advanced. © 1971 Springer-Verlag.

Go to article

First Prev Next Last