Digital Commons Network^™

Seismic Investigation Of Flint Clay Deposits In East Central Missouri, Roland D. Dayley

Masters Theses

"Seismic refraction surveys were conducted in several localities within the east central Missouri clay districts in order to determine the applicability and economy of this method as a clay exploration tool. Results of these surveys revealed that the sink-type clay deposits possess lithologic and structural characteristics that lend themselves favorably to this method of exploration.

Seismic records obtained from profiles shot across known deposits indicate that several factors other than velocity contrast serve to produce apparent seismic anomalies.

Some unforeseen time loss and expense was encountered because of malfunctions of the seismic equipment employed, which necessitated the purchase and installation …

Study Of The Design Of Reinforcement For Prestressed Concrete And Blocks, Charles Robert Hoffman

Masters Theses

"This thesis is an analysis of the transverse tensile stress condition in an end block of a prestressed concrete beam. A stress analysis was made by photoelasticity and compared to the mathematical solutions and experimental solutions performed by others on concrete models. The photoelastic model was made from a piece of Columbia Resin, 39.

Whatever method is chosen to determine the stress condition, there is no exact code that can be established to fit the various type problems which arise"--Abstract, page 1.

Porous Cooling Of A Pile, Tarsem Singh Purewal

Masters Theses

"In this investigation the problem of a limiting case of steady state one dimensional solid-fluid Newtonian heat transfer is examined in which an incompressible non-heat generating coolant fluid is flowing through a heat generating porous plate.

The effect of grain size on the Newtonian heat transfer in the porous plate with various kinds of internal heat generations is determined analytically. The temperature difference between the solid and the coolant fluid through the porous plate is determined. All the previous studies assume that in the porous plate, coolant fluid temperature and solid temperatures are approximately equal. This analysis eliminates this simplifying …

Mechanics Of The Voussoir Arch As Applied To Block Caving, Christopher Haycocks

Masters Theses

"The theories of ground failure in massive rock with special reference to the problem of the mechanics of block caving were studied and evaluated.

The mechanics of arch or dome formation underground were studied quantitatively using the Voussoir arch theory. The effect of shear stress on the arch stability was considered and found to affect the system only when the arch height increased beyond certain limits.

A theory of the mechanism of ground failure in an undercut block using the dome theory was advanced. Photo- elastic model studies were used to support the conclusions reached"--Abstract, page i.

The Dielectric Strength Of Some Anti-Corrosive Paints, George Albert Chappell Iii

Masters Theses

"Corrosion has been one of the costly problems to industry because each year losses due to corrosion are in excess of six billion dollars. Corrosion is caused by the tendency of all metals to become oxidized and return to their natural state. Oxidation may be suppressed by restraining the flow of electrons from the system, thereby inhibiting corrosion.

One effective means to prevent rusting is by applying a barrier of paint between the system and the corrosive atmosphere. Not all paints, however, are equally effective as corrosion inhibitors. At present, the only effective means of determining the corrosion resistant ability …

A Model Study Of The Behavior Of Elastic Liners In Shallow Underground Openings, Martin Samuel Oudenhoven

Masters Theses

"Models of epoxy resin were used in a stress freezing technique to determine areas of possible failure in lined circular openings. These models were loaded in a centrifuge for a fixed period of time, after which they were analyzed photoelastically. The material characteristic changes, with time, were recorded on graphs and used in the analysis.

Two types of tests were conducted; one, where the lining thickness was changed and, the other, where materials of the liner and plate material were changed.

The resulting analyses furnished proof that the greater the rigidity of the lining, the higher the stress developed in …

A Comparison Of A-C And D-C Lead Compensation From D-C Prototype Networks, Piyush Parikh

Masters Theses

"The object of this thesis is to study the difference in transient and frequency response characteristics between a prototype d-c phase lead compensating network and an equivalent a-c phase lead compensating network.

A second order servo is selected to be compensated and five d-c prototype and equivalent a-c phase lead compensating networks are designed. The frequency characteristics of the a-c networks are obtained experimentally and these of the d-c networks are obtained analytically. The characteristics of both networks are compared and their differences are studied. The transient characteristics of the d-c and a-c compensated closed-loop systems to a step input …

A Model Study Of The Induction Log Applied To The Detection Of Asymmetrically Located Orebodies, Robert Walter Piekarz

Masters Theses

"This research project was undertaken to determine the possibility of using an induction log of the type applied in petroleum exploration, for the detection of conductive ore- bodies asymmetrically located with respect to a borehole. Since a mathematical analysis would be extremely complex, a model study was conducted, using graphite bodies of various shapes to simulate different modes of mineral occurence.

The investigation showed that these bodies were readily detectable, and were capable of yielding anomalous curves characteristic of their geometry. The values of apparent conductivity decreased rapidly with lateral displacement, from the logging tool, as expected, due to the …

Transpiration Cooling Of A Heat Generating Porous Plate, M. K. A. Hameed

Masters Theses

"This investigation is a continuation of a thesis by T. S. Purewal. Several of the simplifying assumptions made by the above author are either ignored or the justifiability of such assumptions is probed into in order to obtain a more rigorous solution. Effects of the assorted grain size, non-Newtonian cooling, direction of coolant flow, thickness of the porous heat generating plate, specific heat of the coolant, and compressibility of the coolant are investigated in this thesis. Variation of maximum temperature of both coolant and the solid material for different types of heat source distribution are also studied.

As the grain …

A Preliminary Study Of The Effect Of Heat Treatment On The Strength And Microstructure Of A Glass-Ceramic Material, P. D. Ownby

Masters Theses

"The strength and microstructure of a glass-ceramic material of the composition 53 percent SiO₂, 19 percent Al₂O₃, 15 percent MgO, and 13 percent Li₂O were studied. Cylindrical specimens of glass were formed and heat-treated to six different temperature levels for various time periods. The method of strength testing used was a diametral compression loading technique. It was found that the strength of this material increased initially with heat-treatment but then decreased. The strength characteristics of the completely crystallized glass ceramic material were found to be dependent on the initial nucleation period. Some factors which influenced anomalous crystal growth are described. …

Mineral Paragenesis And Trace Element Distribution In The Tri-State Zinc-Lead District Missouri, Kansas, Oklahoma, Richard D. Hagni

Doctoral Dissertations

"A review of the literature pertaining to the mineral paragenesis and trace element distribution in the Tri-State zinc-lead district of Missouri, Kansas, and Oklahoma revealed inconsistencies in observation and in interpretation and divergent hypotheses regarding the origin of the ores. In an attempt to reconcile the data collected by many investigators over nearly three-quarters of a century, the writer observed working faces in 37 mines, collected over 2,000 specimens for binocular examination and prepared and studied 110 polished surfaces and 60 thin sections of the ores and associated rocks utilizing mineralographic, petrographic, and x-ray techniques. This detailed study resulted in …

Ground Water Investigation In The Southern Half Of Franklin County, Missouri, Kemal Piskin

Masters Theses

"Increasing population and industrialization in Franklin County, Missouri, has led to increased demand for water. Much of this demand will be satisfied from ground water resources. Although the general geology of Franklin County has been mentioned in several publications, no detailed study of structure and ground water geology had been done. This thesis consists of study of stratigraphy, lithology, and geologic structure, and analysis of well log data to determine occurrence and availability of ground water, in the southern half of Franklin County.

Stratigraphy and lithology is compiled from previous literature, modified to agree with well log data. Structural geology …

Foraminifera Of The Cenozoic And Recent Genus Sphaerogypsina Galloway, Wayne C. Horton

Masters Theses

"The morphology of Sphaerogypsina as seen in thin section affords various characters useful in classification] 1) arrangement and composition of the wall (calcareous-perforate, radially crystalline); 2) layering of wall (like Gypsina, without layering or black line, having only microlamellae); 3) shape of test (always spherical); and 4) specific characters: size of test, order/unorder ratio, size of chambers, wall thickness, pore diameter, and type of embryonic apparatus.

Correlation of the above characters has allowed recognition of two new species. Comparisons with other genera strongly suggest placing the genus in the Family Gypsinidae (nom. correct.) rather than in the …

A Study Of Duffing's Equation, Charles Kirby Murch

Masters Theses

"The unforced cases of Duffing's equation and the equation of the simple pendulum are considered by imposing certain conditions on a linear partial differential equation. Geometrical arguments are presented which lead to solutions of the special cases considered.

Undetermined functions of integration in the solutions limit their use to the approximation of systems with small non-linearity"--Abstract, page ii.

The Effect Of The Rolling Load On The Micro-Structure Of Low Carbon Sheet Steel, Jerry Lee Cadden

Masters Theses

"A Stanat 315, two high-four high, combination rolling mill is used to cold roll annealed, low carbon steel strips. A method of measuring the rolling load was presented. The method consisted of constructing a load cell using SR-4 strain gages attached to a steel column. The load cell was placed under the hold down screw of the rolling mill and a known load was applied. The stresses from this load were transferred to the mill housing where another SR-4 strain gage was located. The strain in the mill housing was recorded at the corresponding applied load. During rolling, the strain …

Transpiration Cooling Of A Porous Plate, Stephan A. Sayegh

Masters Theses

"Transpiration cooling has long been known as an effective way of removing heat from porous materials. This thesis is a new approach to one of the problems of transpiration cooling in the steady state.

The specific problem considered here is that of a uniform porous plate through which a liquid is forced. This liquid vaporizes at a short distance from the surface through which it is forced and leaves the porous plate at the other surface which is exposed to hot gases. It also protects the hot surface by forming an insulating layer between that surface and the hot gases. …

Analysis Of Flat Plates By Reaction Distribution Method, David D. W. Yang

Masters Theses

"This study was made to analyze rectangular flat plates by the method of Reaction Distribution and to compare results obtained by this method with that of other methods. The basic approach is to divide the plate into an equivalent grid system and introduce temporary supports at the intersecting joints. The results from this study shows that the Reaction Distribution method is useful in a qualitative analysis of the behavior in a plate but is less satisfactory in obtaining reliable quantitative results"--Abstract, page 2.

A Study Of The Permeability And Separation Of Carbon Dioxide And Hydrogen By Gaseous Diffusion Employing Barriers Of Polystyrene, Carl J. Wallace

Masters Theses

"The purpose of this investigation was to study the permeability and separation of carbon dioxide and hydrogen by gaseous diffusion employing barriers of polystyrene. The offset of temperature and barrier thickness on the permeability and separation of carbon dioxide and hydrogen wore Investigated for barriers of one, three, and five-mil thicknesses and for temperatures of 26, 35, 45, and 50 degrees centigrade.

With an increase in barrier thickness of one to five- mils, the permeability of carbon dioxide decreased to one-fourth of its value at the one-mil thickness. The hydrogen permeability decreased to approximately two- thirds of its value at …

A Study Of Composite Beams Made To Find An Approximate Relationship Between The Top And Bottom Flange Steel Ratio, Murli U. Hasrajani

Masters Theses

"At present in building construction the use of the composite beams is not very common. The use of the concrete beams is seen in almost all construction. By using composite beams in building construction more durability and savings in cost could be achieved. This paper shows an approximate design procedure which could be followed without running a number of trials with different sections to arrive at the required one. The ratio of top flange steel to the bottom flange steel can be determined if one knows the loads, span and the depth of the beam required"--Abstract, page i.

Neutron Flux Mapping Of The Msm Reactor, Cary Chow-Yuen Chen

Masters Theses

"This investigation presents a mean to determine thermal neutron flux of a reactor by irradiating copper wires inside the fuel elements. The activity recorded after decay correction, is the relative thermal neutron density. Thermal neutron flux is a measure of the neutron density at thermal energy, 0.025 ev.

Gold foils irradiated at National Bureau of Standards were used as the absolute neutron flux calibration standards. The average flux of the reactor with water as the reflector ranges from 7.24 x 10¹⁰ neutrons/cm² - sec. to 7.87 x 10¹⁰ neutrons/cm² - sec. as obtained from the calculations. …

A Study Of Placer Tin Materials From Southern Thailand, Somkiat Ganthavee

Masters Theses

"This thesis deals with a series of investigations of placer tin samples from a Chinteik's Tin-dredge, Gnaw District, Ranong Province, and the Tin-Pet mine, Phang-gna Province, in southern Thailand.

A brief summary of the geography and geology of Thailand as a whole has been given as a general introduction to the source of the materials studied in this thesis.

The results of sieve analyses have shown that the sluice boxes do not effectively concentrate the cassiterite grain below 0.147 mm. from the rough concentrate treated in the tin-dressing shed.

It has been found that roundness and shape determinations of quartz …

Syntheses And X-Ray Investigations Within The System Fes₂-Cos₂, Samuel Shu Mou Chan

Masters Theses

"Pyrite (FeS₂), cattierite (CoS₂), and various transitional members of the solid solution compounds were prepared. The methods used are as follows:

First, sulfides of cobalt, iron, or cobalt-iron were obtained by precipitation from a mixture of the cobalt chloride and/or ferrous sulfate in an aqueous solution. The dried precipitates were then mixed with an equal weight amount of sulfur and placed into silica glass tubes. After evacuation, they were filled with hydrogen gas of 3/4 of atmospheric pressure and sealed. The samples were then heated up to 500°C (for FeS₂), 650°C (for FeS_{2 …}

Analog Study Of Vibratory Forces In Sorting Machine, Navnit Chhaganlal Mehta

Masters Theses

"This investigation involves the study of the reduction of vibratory forces in a sorting machine. The equivalent masselastic system is shown in Figure 1, in solid lines. In this figure the mass m₁ represents the main structure for the mounting of the machine, the mass m₂ is the main bearing blocks and the mass m₃ is the vibrating basket. The elastic stiffness indicated as k₁ represents the mounting spring for the entire unit, the stiffness k₂ is that of the beam structure by which the bearing block is attached to the main structure, and the stiffness k₃ is that of …

Application Of Digital Computer To Magnetic Data Interpretation Using Surface Integral Method, Afif Hani Saad

Masters Theses

"A simple method is developed for the calculation of the magnetic effect due to three-dimensional bodies. The method is based on the use of surface integration instead of volume integration. Thus, any three-dimensional body can be considered as having two surfaces, upper and lower, with magnetic pole distributions. Simple equations based on potential theory have been derived for the calculation of the vertical component and total intensity due to these surface distributions of poles. The anomalous field of the body can be obtained by subtracting the effect due to one of the surfaces from that of the other.

The method …

Study Of The Copper-Uranium Deposits At Vilcabamba, Department Of Cuzco, Peru, Oscar Aguilar

Masters Theses

"Uranium has been known in the Vilcabamba district of Cuzco, Peru since 1954. Copper ores of high silver content were worked by the Spaniards during the seventeenth and the early eighteenth centuries, At the beginning of the twentieth century these ores were worked intermittently; during the last fifty years no mining operation has been going on.

The oldest rocks in the thesis area consist of Ordovician phyllites. The presence of Devonian in the area is questionable, but has been recognized 5 km. away from the thesis area. A conglomerate of limited lateral extent of Mississippian age overlies the Devonian (?) …

A Study Of The Stress Distribution Around Circular Openings Using Multilayered Photoelastic Material, Donald Frank Haber

Masters Theses

"Stress analysis as applied to mine openings ranges from the completely empirical to the completely theoretical. However, it is only through the ultimate utilization of the two methods that a guide to the Interpretation of mine stress phenomenon may be obtained. The bridge between the two approaches lies in the field of model study. Specifically, this is an Investigation into determining the feasibility of using multilayered photoelastic materials in models such that a more exact approximation of the underground stress distribution around mine openings can be made.

The two major objectives in this study for determining the feasibility of using …

A Study Of The Colloidal Properties Of Zirconium And Promethium By Electrodialysis And Liquid-Liquid Extraction, James N. Click

Masters Theses

"The purpose of this investigation was to study the solution chemistry of zirconium by investigating the colloidal behavior of natural zirconium and zirconium-95, utilizing electrodialysis and liquid-liquid extraction techniques. Also incorporated into this study was the investigation of optimum conditions for the extraction of the natural zirconium and zirconium-95 with thenoyl trifluoracetone. A limited amount of work was done on the colloidal nature of promethium-147"--Introduction, pages 2-3.

Model Analysis By The Moiré Method, David D. Kick

Masters Theses

"This study presents the use of Moiré fringes for model analysis of deflections and strains. Deflection of a beam, strain in a disk, and an Influence diagram for a frame are presented as examples of uses of the Moiré method. The necessary equations for the determination of strain using the Moiré method are also derived and presented in this work"--Abstract, page v.

Investigation And Development Of Ground Water Of Chalone Creek, (Pinnacles National Monument, California), Donald Lee Brown

Masters Theses

"The Pinnacles National Monument is located in San Benito and Monterey Counties about 130 highway miles south of San Francisco, California. Because of unusual patterns in volcanic rocks, the Monument was set aside as a recreation area on January 16, 1908, by President Theodore Roosevelt. It encompasses an area of approximately 12,818 acres.

Water quality and supply problems were experienced at the Monument in the few years prior to 1961. In 1961, a collection trench system was installed to alleviate the water supply condition. A horizontal trench system, 215 feet long and four feet below the dry season water table, …

Statistical Analysis Of Fracture Stresses Of Triaxial Porcelain Bodies, Robert E. Moore

Doctoral Dissertations

"Triaxial porcelain bodies containing various forms of silica, quartz, cristobalite and fused silica, were strength tested in bending. Significance tests were employed to discern real differences in the strength sample statistics caused by the various forms of silica. Firings were performed at three temperature levels. The differences in strength sample statistics were correlated to the microstructures of these silica porcelains.

A triaxial alumina porcelain body was employed as a model brittle solid for a study of the effect of flaw density on mean fracture stress. The flaws were introduced in the form of large diameter (d̄ = 115 microns) rounded …