Digital Commons Network^™

The Use Of Turbulence Energy Equation In Boundary Layer Study, Ro-Chi Tai

Masters Theses

"A turbulent boundary layer problem has been studied analytically and compared with an available experiment in the literature. Correlations of the experimental data were made to investigate the validity of the commonly used empirical relations on turbulent shear stresses. It was found that the model which related the local turbulent shear stress linearly with the local turbulent kinetic energy, as used by Bradshow et. al., appeared to be most reasonable. combining this model with the expression of turbulent viscosity given by Boussinesq, it was then possible to introduce the turbulence-energy equation in addition to the governing equations of continuity and …

Analog Simulation Of Mass Transfer In Droplets With Turbulent Internal Circulation, Jeffrey Tsai-Hwa Kuo

Masters Theses

"The object of this thesis is to simulate the Handlos and Baron Model for mass transfer into droplets by using an iterative analog computer in order to obtain eigenvalue and other parameters in a series solution. The eigenvalues λ_n calculated in this work are compared with the results obtained by Wellek-Skelland using a variational technique and by Patel using numerical approaches on the digital computer. From the analytical series solution, one can calculate the fraction of solute extracted in the droplets as a function of droplet contact time. PACTOLUS, a digital-analog simulator, provides a check on the validity of …

Basic Design Of Mosfet, Four-Phase, Digital Integrated Circuits, Earl Morris Worstell

Masters Theses

"MOSFET is defined as metal oxide semiconductor field-effect transistor. The integrated circuit design relates strictly to logic and switching circuits rather than linear circuits. The design of MOS circuits is primarily one of charge and discharge of stray capacitance through MOSFETS used as switches and active loads. To better take advantage of the possibilities of MOS technology, four-phase (4[phi]) circuitry is developed. It offers higher speeds and lower power while permitting higher circuit density than does static or two-phase (2[phi]) logic. Equations are developed that apply directly to the design of four-phase logic along with examples of circuitry that show …

Current Characteristics Of Electrically Sprayed Glycerine, Larry Eugene Stoddard

Masters Theses

"The current carried by electrically-sprayed glycerine was measured, and an empirical relation was obtained for single-jet spraying, given by I = K_IV^0.45M^0.55̇d^-0.18 where V is the electrode voltage, Ṁ the mass-flow rate, and d the electrode spacing, the electrodes being a capillary and collecting plate. Peculiarities of the current waveform, including an exponentially rising envelope, for unstable-jet spraying and multiple-jet spraying, were recorded"--Abstract, page ii.

State Assignments For Non-Normal Asynchronous Sequential Circuits, Gary Keith Maki

Masters Theses

"There is a lack of procedures that can be used to find good internal state assignments for asynchronous sequential circuits operating in the non-normal mode. Presented here, are two generalized state assignments, which are functions only of the number of rows in a flow table. The suggested bounds for the generalized state assignments are m + [log₂m] and m + [m/2] internal state variables for a 2^m-row flow table, where [ ] means "next lowest integer". Both generalized state assignments produce group (linear) codes. The algorithms for generating these internal state assignments are easy and straight-forward to implement. …

A Comparison Of Lumped Parameter Models Commonly Used To Describe One-Dimensional Vibration Problems, Suresh Kumar Tolani

Masters Theses

"Three lumped parameter model representations of the one-dimensional uniform continuous system in a vibration state are examined. The exact (continuous) solutions were used as a reference to evaluate the accuracy of the results obtained via these discrete element models. The model comparisons, carried out for both the principal modes and the systems under forced excitations, are based on the maximum strain energy. The effect of varying the number of segments in the model representation showed improvement in approximating the exact strain energy solution as the number of segments was increased. In general, the results of the model comparisons based on …

Consistency And Cluster Size In The Effective Field Theories Of Ferromagnetism, J. G. Chervenak, Harry A. Brown

Physics Faculty Research & Creative Works

No abstract provided.

A Determination Of The Speed Of Light By The Phase-Shift Method, John Rogers, Ronnie Mcmillan, Robert Pickett, Richard A. Anderson

Physics Faculty Research & Creative Works

A low-frequency, phase-shift method for the measurement of the speed of light has been developed. This technique gives results commensurate with other advanced laboratory methods. One advantage of this technique is that the apparatus is of reasonable size and most of the circuitry involves widely known amateur radio techniques. Furthermore, our use of a low modulating frequency permits use of the solid-state, electro-optical light shutter. This eliminates the rather dangerous liquid Kerr cell, thus making our apparatus more acceptable to application in the undergraduate advanced laboratory. From a pedagogical point of view, the student is allowed to use and become …

Mixed Magnetic Systems: A Model With Application To (1-X)Cdcr2s4 · Xcdcr2se4, Harry A. Brown

Physics Faculty Research & Creative Works

The Curie temperatures and asymptotic Curie temperatures are calculated for mixed magnetic systems by a semi-classical Bethe-Peierls-Weiss cluster approach. The systems are typified by (1-x) CdCr2Se4 · xCdCr2Se4 in which the substitution changes the anions but not the magnetic cations. It is found that next-nearest-neighbor interactions are needed to match the data but that, with them, excellent agreement can be obtained for a reasonably unique choice of the exchange integrals. © 1969.

Semiempirical Determination Of The Hydrogen Bond Energy For Water Clusters In The Vapor Phase. I. General Theory And Application To The Dimer, Richard W. Bolandee, James L. Kassner, Joseph T. Zung

Physics Faculty Research & Creative Works

A simple semiempirical method is given for determining the hydrogen bond energy for water clusters in the vapor phase. This method is based on a general statistical-mechanical theory of clustering. The partition function for a system of clusters is used to determine the equilibrium distribution of clusters. In conjunction with available thermodynamic and spectroscopic data, the cluster equilibrium constants can be used to calculate the cluster potential energy and the hydrogen bond energy. Results for the water dimer agree quite well with other reported values obtained either by quantum-mechanical calculations or approximate thermodynamic estimates. A correct temperature dependence of the …

Methods For Evaluating The Performance Of Small Acoustic Filters, William S. Gatley, Raymond Cohen

Mechanical and Aerospace Engineering Faculty Research & Creative Works

Experimental methods are needed for determining the characteristics of small acoustic filters used in systems with pulsating gas flows. These characteristics could then be used to predict the performance of proposed filter designs in a particular system, according to plane wave acoustic theory. Dependence on trial-and-error experimentation in solving noise control problems would thus be minimized. A literature survey revealed only a few earlier attempts to evaluate the acoustic performance of small filters and filter elements. Three methods for determining reflection and transmission factors are described, evaluated, and compared. A method employing a standing wave tube of unique design is …

Mass And Heat Transfer Relations In Evaporation Through Porous Membranes, Marshall E. Findley, V. V. Tanna, Y. B. Rao, C. L. Yeh

Chemical and Biochemical Engineering Faculty Research & Creative Works

This study concerns rates of evaporation and mass transfer of water vapor from a heated salt solution through a water repellent porous membrane to a cooled water condensate. This transfer is a result of temperature differences and corresponding vapor pressure differences across the membrane. Three groups of experiments were carried out which indicate that the major factor influencing the rates of transfer is diffusion through a stagnant gas in the membrane pores. However, an equation considering film heat transfer coefficients, membrane thermal conductivity, and an empirical correction based on temperature driving force appears to be necessary for representing all the …

A Study Of Different Types Of Connections To Structural-Steel Square Tubings, Chao-Sheng Chen

Masters Theses

"Although square tubular element has long been recognized as an ideal structural member, its acceptance was limited by the lack of detailed knowledge on suitable connections related to this geometric shape. It is structurally inefficient to use a strong column poorly connected to a strong beam. So it is necessary to understand, in advance of adoption, the effect and behavior of different types of connections and to develop an efficient structural system. In this study, the ordinary column-to-beam framing with different types of connections has been investigated. The three types of connections are single-plate connection, double-angle connection, and multi-angle connection. …

Numerical Simulation Of Pressures In A Radical System, Vijender Nath Gopal

Masters Theses

"The time-space location of an advancing front has been described in such a manner as to permit the calculation of frontal pressures when a heterogeneous (in permeability) radial system is subjected to water encroachment. A finite difference application has been developed to calculate these pressures at specified radial distances from the injection or production wellbore. These pressure have been further utilized to predict the pressures at the advancing front for different time intervals"--Abstract, page iii.

A Computerized Method For Finding The Dynamic Response Of Multi-Mass Systems With Damping To Arbitrary Inputs, Bakulesh Balbhadra Patel

Masters Theses

"A practical procedure for the systematic application of Foss's method to the solution of multi-degree-of-freedom damped systems is presented. It is relatively easy to determine the response of classically damped systems to various inputs. For non-classically damped systems the method proposed by K. A. Foss has been employed. This method gives an exact and complete solution for the response of linear multi-mass damped systems subjected to arbitrary inputs. Since the method requires lengthy and complex computations, the use of a digital computer is essential. In order to obtain the complete response of a multi-mass damped system to both sinusoidal and …

A Study On Load Transfer Of Model Friction Piles, Richard Milton Franke

Masters Theses

"Previous investigations concerned with disturbance of soft clay by driving displacement piles are summarized. The initiation of excess pore water pressures due to pile driving, and mechanisms of load transfer are also described, along with the applicapability of model pile testing in analysis of the various phenomena. Load tests were conducted on assorted sizes of model friction piles embedded in sedimented soil samples with consisted of a silt and clay mixture. Pilot holes of various diameters were cut in the samples. A theoretical load distribution curve was used to calculate the load transferred to the soil as a function of …

Plastic Analysis Of Beam - Columns, Ning-Cheng Tsao

Masters Theses

"The results of an analytical study of the inelastic deformation of a wide-flange steel beam-column are presented. Emphasis has been placed on the influence of axial thrust on the pinned-end beam-column subjected to equal end moments with opposite direction. For this type of beam-column behavior, the relationship between the applied moment, axial load, and resultant curvature for the region in the plastic range has been studied in this investigation"--Abstract, page ii.

Determination Of Distillation Efficiencies For The Water-Methanol-Acetone System, Chorng Shyong Wang

Masters Theses

"A pilot-scale, eight-plate, bubble-cap distillation tower with a multi-point temperature recorder and automatic sampling device was used to obtain operating data on temperatures and liquid phase compositions for distillation efficiency studies. The tower was run with a single feed, a total condenser, and a partial reboiler. At steady state, as indicated by constant temperatures, samples were taken and later analyzed by gas chromatography. A digital program was developed to calculate component efficiencies on each plate according to Holland's modified Murphree plate efficiency, utilizing the operating data, and reflux rate, the input and output flows and compositions, and vapor-liquid equilibrium data. …

Investigation Of Free Convection Heat Transfer From An Inclined Flat Plate, Phairojna Sang-Urai

Masters Theses

"The experimental investigation was conducted to determine temperature distribution and convective heat transfer coefficients in terms of Nusselt number for an inclined heated flat plate in air. The heated surface of the aluminum flat plate was set facing upward and moved through seven positions from the vertical to the horizontal. The investigation shows that the local Nusselt number can be predicted by Kiekus's solution within 12 per cent for inclination angles from the vertical through 75° from the vertical. In the case of the vertical position, Eckert's solution gives a better prediction. For the horizontal position the results show good …

Effect Of Axial Mixing In Gas Absorption, Sundareswaran Parameswaran Iyer

Masters Theses

"The effect of axial mixing in the liquid phase on the performance of a gas absorption column was studied using the experimental data of Michael Brittan for the carbon dioxide and water system. In this study, piston flow conditions were assumed for the gas phase. A one-parameter mathematical model, which characterized the flow regimes in both the gas and the liquid phases undergoing plug flow conditions, was first curve fitted for its unknown parameter (i.e. the Number of Transfer Units) by a non-linear regression analysis procedure. The "AAPD" (i.e. the Average Absolute Percentage Deviation between the predicted value of the …

Trace Element Anomalies In The Igneous Wall Rocks Of Hydrothermal Veins In The Searchlight District, Nevada, Zuhair Al-Shaieb

Masters Theses

"Two hundred and fifty vein and wall rock samples were collected from Chief of the Hill and the Duplex Mines of Searchlight District, Nevada. The samples were collected along lines approximately normal to the veins. They were analyzed for lead, copper, zinc, silver, gold, arsenic, selenium, and molybdenum using neutron actication analysis and atomic absorption spectrophotometry. Gold, silver, copper, lead and zinc show well-developed anomalies in the wall rocks. In most cases, the concentration of these elements decreases gradually with increasing distance from the vein and reaches background values at a distance of 40-120 feet from the vein. Molybdenum and …

A Simple Observational Technique For The Investigation Of Boundary Layer Stability And Turbulence, Tony Maxworthy

Symposia on Turbulence in Liquids

A dense suspension of aluminum flakes in a fluid has many advantages as a flow-visualization method, and has been used to study circular Couette flow and Benard instability, among others. In the present contribution the scientific and pedagogical merits of the technique are examined further for three different cases: (a) Stability of Poiseuille flow; (b) Stability of the side-wall boundary layers created when a fluid-filLed, rotating container is suddenly brought to rest; (b) Stability of the boundary layer beneath a concentrated vortex.

The technique is also useful in other cases, especially when fundamentals of fluid flow are to be demonstrated …

The Background Concentrations Of Copper, Lead, And Zinc In Streams Of The "New Lead Belt", Missouri, Nicholas Howard Tibbs

Masters Theses

"This study was initiated to determine the background concentrations of copper, lead, and zinc in the streams of the Viburnum Trend or New Lead Belt of southeast Missouri. Analytical methods were developed for atomic adsorption spectroscopy. These methods initially consisted of coextraction of cooper, lead, and zinc using the APDC/MIBK system, and finally of extraction of copper by APDC/MIBK and direct analysis of lead and zinc using the newly developed "Sampling Boat" technique. The data obtained from these analyses were arranged in histograms and critically analyzed. The background concentrations were established to be 4-6 ppb for all three elements. Methods …

Longitudinal Optical Phonon-Plasmon Coupling In Ionic Semiconductors, Thomas Joseph Mcmahon

Doctoral Dissertations

"The coupling of free carriers and lattice vibrational modes is studied in CdS and InSb by room temperature far infrared reflectance measurements. When the free carrier concentration is such that the plasma frequency is at or near the longitudinal optical mode frequency it is shown that while the transverse modes remain fixed, the longitudinal modes mix with the plasma mode and are shifted in a manner similar to that described by Varga in 1965. Using the dielectric function for the coupled system permits the determination of electron effective masses by reflectance measurements with lattice effects excluded. This method allows one …

Dynamic Response Of Circular Plates To Transient And Harmonic Transverse Loads Including The Effect Of Transverse Shear And Rotary Inertia, Perakatte Joseph George

Doctoral Dissertations

"Using an improved theory of plate vibration suggested by R. D. Mindlin which takes into account the effects of transverse shear and rotary inertia, free and forced transverse vibrations of uniform circular plates are studied and the results compared with those obtained using the classical theory of plate vibration. The governing equations are developed in polar coordinates using the equations of elasticity. Frequency equations for axisymmetric and antisymmetric vibrations are derived for solid circular plates under different boundary conditions and for an annular plate rigidly mounted on a shaft. The response of plates to different types of rapidly applied axisymmetric …

A Five Parameter Study Of Spherical Transient Waves In A Generalized Voigt Model, Liang-Juan Tsay

Doctoral Dissertations

"Transient spherical waves in a generalized Voigt model were investigated in this study. Both Laplace and fourier transform solutions of the spherical wave equation for a generalized Voigt model were obtained by means of the correspondence principle. Laplace transform solutions were inverted numerically into the domain for the study of the characteristics of the wave forms, and Fourier transform solutions were utilized for the analysis of frequency dependency attenuation in the models. Generalized Voigt models A and B in which a dashpot is connected in series with spring and dashpot components were unable to represent a solid which would simulate …

A.C. Hall Effect Measurements On Very High Resistivity Materials Exhibiting Electrode Polarization, James Dale Boyd

Doctoral Dissertations

"A variable frequency, a.c. Hall effect measurement technique has been designed for mobility studies in very high resistivity (>10⁹ ohm·cm) materials exhibiting electrode space charge polarization effects. It incorporates a neutralized input capacitance preamplifier detector which reduces the total input shunting capacitance, including the sample interelectrode capacitances, to a very low, definable value (<0.1 pf) and thereby provides very high and well defined a.c. detector input impedances (4 x 10⁹ and 7 x 10⁹ ohms at 600 and 200 Hz, respectively). Lumped parameter equivalent circuits have been defined to approximate the electrical behavior of sample materials in the measurement configuration. These equivalent circuits, together with independent measurements of the detector input and sample impedances, allow one to correct the detected Hall voltage and obtain the true value from which mobility data may be derived. The validity of these circuits has been established by independent a.c. and d.c. measurements on photoconductive CdS (dark resistivity >10¹⁰ ohm·cm) which exhibited maximum differences of less than 4%. The existing literature has been critically reviewed and the measurement criteria established by this study have been applied to resolve differences in reported data and to suggest improvements in the resolution of previously employed experimental …

An Optimization Approach To Well Spacing For Gas Storage Reservoirs, Jagannath Rao Ghole

Doctoral Dissertations

"A finite approximation to the conventional diffusivity equation describing compressible fluid flow through porous media has been developed with a view to apply it to the problems of optimum well spacing. An equilateral grid system has been employed to enable uniform well spacing for any number of wells. A numerical model has been developed on an IBM 360 - Model 50 computer, which simulates the pressure and saturation transience in the reservoir due to production impulses. This model has been used to maximize with respect to number of wells, the minimum well bore pressure reached throughout the specified withdrawal schedule. …

Analysis Of The Traveling-Wave Transistor, Vernon Ray Stanley

Doctoral Dissertations

"Transmission lines containing independent and dependent distributed sources are considered and the transfer matrices of various active distributed lines are derived. A method is discussed by which a lossy line can be made lossless by the appropriate choice of distributed sources. A steady-state analysis of the uniform traveling wave transistor is given. Considering the device as an active four port network, the transfer matrix is found in closed form and the power gain, output voltage, and input impedance are found. A computer program is written and the frequency response is given for various values of line parameters and terminations. Finally, …

Characterizing Topologies By Continuous Selfmaps, Derald David Rothmann

Doctoral Dissertations

"Various topological spaces are examined in an effort to describe topological spaces from a knowledge of their class of continuous selfmaps or their class of autohomeomorphisms. Relationships between topologies and their continuous selfmaps are considered. Several examples of topological spaces are given and their corresponding classes of continuous selfmaps are described completely. The problem, given a set X and a topology U when does there exist a topology V either weaker or stronger than U such that the class of continuous selfmaps of (X,V) contains the class of continuous selfmaps of (X,U), is considered. M* and S** spaces are defined …